Effects of multimodal microstructure on fracture toughness and its anisotropy of LPSO-type extruded Mg-1Zn-2Y alloys

The fracture toughness of extruded Mg-1Zn-2Y(at.%)alloys,featuring a multimodal microstructure containing fine dynamically recrystallized(DRXed)grains with random crystallographic orientation and coarse-worked grains with a strong fiber texture,was investigated.The DRXed grains comprised randomly oriented equiaxedα-Mg grains.In contrast,the worked grains includedα-Mg and long-period stacking ordered(LPSO)phases that extended in the extrusion direction(ED).Both types displayed a strong texture,aligning the(10.10)direction parallel to the ED.The volume fractions of the DRXed and worked grains were controlled by adjusting the extrusion temperature.In the longitudinal-transverse(L-T)orientation,where the loading direction was aligned parallel to the ED,there was a tendency for the conditional fracture toughness,KQ,tended to increase as the volume fraction of the worked grains increased.However,the KQ values in the T-L orientation,where the loading direction was perpendicular to the ED,decreased with an increase in the volume fraction of the worked grains.This suggests strong anisotropy in the fracture toughness of the specimen with a high volume fraction of the worked grains,relative to the test direction.The worked grains,which included the LPSO phase and were elongated perpendicular to the initial crack plane,suppressed the straight crack extension,causing crack deflection,and generating secondary cracks.Thus,these worked grains significantly contributed to the fracture toughness of the extruded Mg-1Zn-2Y alloys in the L-T orientation.

Effect of microstructure on impact toughness of magnesium alloys

Microstructures of as-cast and extruded ZK60-xRE （RE=Dy, Ho and Gd, x=0-5, mass fraction） alloys were investigated. Meanwhile, the impact toughness was tested and then the relationship was discussed. The results show that as-cast microstructure is refined gradually with increasing the RE content. Mg-Zn-RE new phase increases gradually, while MgZn2 phase decreases gradually to disappear. Second phase tends to distribute along grain boundary in continuous network. Extruded microstructure is refined obviously to reach the micron level. Broken second phase tends to distribute along the extrusion direction in zonal shape. Impact toughness value -nK increases from 9-17 J/cm2 for as-cast state to 26-54 J/cm2 for extruded state. With increasing the value of -nK, fracture macro-morphology changes from a rough plane via multi-plane with step to V-type plane; and from single radiation zone to two zones of fiber and shear lip, respectively. Fracture micro-morphology changes from the brittle fracture to the ductile fracture. Fine grain and few fine dispersed second phase can enhance the impact toughness of magnesium alloys effectively.

Microstructure and indentation toughness of Cr/CrN multilayer coatings by arc ion plating

Cr/CrN multilayer coatings with bilayer periods in the range from 1351 to 260 nm were prepared on 304 stainless steel substrates by arc ion plating to study the microstructure and properties of multilayer coatings and stimulate their application.SEM results confirm the clear periodicity of the Cr/CrN multilayer coatings and the clear interface between individual layers.XRD patterns reveal that these multilayer coatings contain Cr,CrN and Cr_2N phases.Because Cr layer is softer than its nitride layer,the hardness decreases with the shortening of the bilayer period(or increasing volume fraction of Cr layer).The Cr/CrN multilayer coating with 862 nm period possesses the highest indentation toughness due to a proper individual Cr and nitride layer thickness.However,for the Cr/CrN multilayer with the bilayer period of 1351 nm,it possesses the lowest toughness due to more nitride phase.The indentation toughness of Cr/CrN multilayer coatings is related with their bilayer period.A coating with a proper individual Cr and nitride layer thickness possesses the highest indentation toughness.

Microstructure and fracture toughness of a TiAl-Nb composite consolidated by spark plasma sintering

A TiAl-Nb composite was prepared by spark plasma sintering （SPS） at 1250 °C and 50 MPa for 5 min from prealloyed TiAl powder and elemental Nb powder in a molar ratio of 9：1 for improving the fracture toughness of TiAl alloy at room temperature. The microstructure, phase constitute, fracture surface and fracture toughness were determined by X-ray diffractometry, electron probe micro-analysis, scanning and transmission electron microscopy and mechanical testing. The results show that the sintered samples mainly consist of γ phase, O phase, niobium solid solution （Nbss） phase and B2 phase. The fracture toughness is as high as 28.7 MPa？m1/2 at room temperature. The ductile Nbss phase plays an important role in absorbing the fracture energy in front of the cracks. Moreover, B2 phase can branch the propagation of the cracks. The microhardness of each phase of the composite was also tested.

Microstructures and impact toughness behavior of Al 5083 alloy processed by cryorolling and afterwards annealing

The influence of rolling at liquid nitrogen temperature and annealing on the microstructure and mechanical properties of Al 5083 alloy was studied in this paper. Cryorolled samples of Al 5083 show significant improvements in strength and hardness. The ultimate tensile strength increases up to 340 MPa and 390 MPa for the 30% and 50% cryorolled samples, respectively. The cryorolled samples, with 30% and 50% reduction, were subjected to Charpy impact testing at various temperatures from 190℃ to 100℃. It is observed that increasing the percentage of reduction of samples during cryorolling has significant effect on decreasing impact toughness at all temperatures by increasing yield strength and decreasing ductility. Annealing of samples after cryorolling shows remarkable increment in impact toughness through recovery and recrystallization. The average grain size of the 50% cryorolled sample （14 μm） after annealing at 350℃ for 1 h is found to be finer than that of the 30% cryorolled sample （25 μm）. The scanning electron microscopy （SEM） analysis of fractured surfaces shows a large-size dimpled morphology, resembling the ductile fracture mechanism in the starting material and fibrous structure with very fine dimples in cryorolled samples corresponding to the brittle fracture mechanism.

Microstructures and Toughness of Weld Metai of Ultrafine Grained Ferritic Steel by Laser Welding

3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.

Effect of Microstructure Refinement on the Strength and Toughness of Low Alloy Martensitic Steel

Martensitic microstructure in quenched and tempered 17CrNiMo6 steel with the prior austenite grain size ranging from 6 μm to 199 μm has been characterized by optical metallography （OM）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The yield strength and the toughness of the steel with various prior austenite grain sizes were tested and correlated with microstructure characteristics. Results show that both the prior austenite grain size and the martensitic packet size in the 17CrNiMo6 steel follow a HalI-Petch relation with the yield strength. When the prior austenite grain size was refined from 199 μm to 6 μm , the yield strength increased by 235 MPa, while the Charpy U-notch impact energy at 77 K improved more than 8 times, indicating that microstructure refinement is more effective in improving the resistance to cleavage fracture than in increasing the strength. The fracture surfaces implied that the unit crack path for cleavage fracture is identified as being the packet.

Microstructure-fracture toughness relationships and toughening mechanism of TC21 titanium alloy with lamellar microstructure

The independent influence of microstructural features on fracture toughness of TC21alloy with lamellar microstructure was investigated.Triple heat treatments were designed to obtain lamellar microstructures with different parameters,which were characterized by OM and SEM.The size and content ofαplates were mainly determined by cooling rate from singleβphase field and solution temperature in two-phase field;while the precipitation behavior of secondaryαplatelets was dominantly controlled by aging temperature in two-phase field.The content and thickness ofαplates and the thickness of secondaryαplatelets were important microstructural features influencing the fracture toughness.Both increasing the content ofαplates and thickeningαplates(or secondaryαplatelets)could enhance the fracture toughness of TC21alloy.Based on energy consumption by the plastic zone of crack tip inαplates,a toughening mechanism for titanium alloys was proposed.

Effect of microstructure on the impact toughness of a bainitic steel bloom for large plastic molds

The correlation between the impact toughness and microstructural characteristics of a large bainitic steel bloom has been investigated. The study focuses on microcrack nucleation and propagation in the basic cleavage plane. To analyze the phase transformation during the wind-cooling process, the temperature field of the bloom was acquired by computer simulation, and a continuous cooling transformation experiment was conducted. The results show that compared with the surface of the bloom, the toughness of the bloom’s core is decreased by the increase in proeutectoid ferrite and the coarsening of tempered martensite–austenite constituents. The proeutectoid ferrite decreases the toughness via its effects on carbide precipitation, the formation of martensite–austenite constituents, and the bainite transformation. The relatively large tempered martensite–austenite constituents are conducive to microcrack nucleation and propagation.

Influence of band microstructure on carbide precipitation behavior and toughness of 1 GPa-grade ultra-heavy gauge low-alloy steel

This study investigated the influence of band microstructure induced by centerline segregation on carbide precipitation behavior and toughness in an 80 mm-thick 1 GPa low-carbon low-alloy steel plate.The quarter-thickness(1/4t)and half-thickness(1/2t)regions of the plate exhibited similar ductility and toughness after quenching.After tempering,the 1/4t region exhibited~50%and~25%enhancements in both the total elongation and low-temperature toughness at-40°C,respectively,without a decrease in yield strength,whereas the toughness of the 1/2t region decreased by~46%.After quenching,both the 1/4t and 1/2t regions exhibited lower bainite and lath martensite concentrations,but only the 1/2t region exhibited microstructure bands.Moreover,the tempered 1/4t region featured uniformly dispersed short rod-like M_(23)C_(6)carbides,and spherical MC precipitates with diameters of~20–100 nm and<20 nm,respectively.The uniformly dispersed nanosized M_(23)C_(6)carbides and MC precipitates contributed to the balance of high strength and high toughness.The band microstructure of the tempered 1/2t region featured a high density of large needle-like M3C carbides.The length and width of the large M3C carbides were~200–500 nm and~20–50 nm,respectively.Fractography analysis revealed that the high density of large carbides led to delamination cleavage fracture,which significantly deteriorated toughness.

Effects of Microstructure on the Tensile, Fracture Toughness and Fatigue Behaviour of Gamma Titanium Aluminides

The effects of microstructure on the deformation and fracture behaviour of two-phase TiAl alloys were investjgated under monotonic and cyclical loading conditions, over a range of temperatu res.The tensile behaviour is analyzed for deformation temperatures between RT and 950℃, Fracture resistance behaviour and toughening mechanisms at RT and 800℃ are analyzed. and the inverse relationship botween ductility and toughness is explained using the crack initiation toughness. The preliminary results of load-controlled fatigue behaviour at 800℃ are interpreted using the tensile behaviour because deformation structure and fracture modes are similar under these two loading conditions

Effect of microstructure on the low temperature toughness of high strength pipeline steels

Microstructure observations and drop-weight tear test were performed to study the microstructures and mechanical properties of two kinds of industrial X70 and two kinds of industrial X80 grade pipeline steels. The effective grain size and the fraction of high angle grain boundaries in the pipeline steels were investigated by electron backscatter diffraction analysis. It is found that the low temperature toughness of the pipeline steels depends not only on the effective grain size, but also on other microstructural factors such as martensite-austenite （MA） constituents and precipitates. The morphology and size of MA constituents significantly affect the mechanical properties of the pipeline steels. Nubby MA constituents with large size have significant negative effects on the toughness, while smaller granular MA constituents have less harmful effects. Similarly, larger Ti-rich nitrides with sharp corners have a strongly negative effect on the toughness, while fine, spherical Nb-rich carbides have a less deleterious effect. The low temperature toughness of the steels is independent of the fraction of high angle grain boundaries.

Determining role of heterogeneous microstructure in lowering yield ratio and enhancing impact toughness in high-strength low-alloy steel

Here we present a novel approach of intercritical heat treatment for microstructure tailoring,in which intercritical annealing is introduced between conventional quenching and tempering.This induced a heterogeneous microstructure consisting of soft intercritical ferrite and hard tempered martensite,resulting in a low yield ratio(YR)and high impact toughness in a high-strength low-alloy steel.The initial yielding and subsequent work hardening behavior of the steel during tensile deformation were modified by the presence of soft intercritical ferrite after intercritical annealing,in comparison to the steel with full martensitic microstructure.The increase in YR was related to the reduction in hardness difference between the soft and hard phases due to the precipitation of nano-carbides and the recovery of dislocations during tempering.The excellent low-temperature toughness was ascribed not only to the decrease in probability of microcrack initiation for the reduction of hardness difference between two phases,but also to the increase in resistance of microcrack propagation caused by the high density of high angle grain boundaries.

Mechanical properties and microstructure of an α+β titanium alloy with high strength and fracture toughness

The Ti-Al-Sn-Zr-Cr-Mo-V-Si （Ti-62A） alloy, an alpha-beta alloy with high strength and fracture toughness, is currently used as an advanced structural material in aerospace and non-aerospace applications. Thermo-mechanical processes can be used to optimize the relationship between its strength and fracture toughness. A Ti-62A alloy bar can be machined through a transus β-forged plus α＋β solution treated and aged specimen with a lamellar alpha microstructure. The effects of heat treatment on the mechanical properties were discussed. Heat treatment provided a practical balance of strength, fracture toughness, and fatigue crack growth resistance. A comparison of the Ti-62A alloy with the Ti-62222S alloy under the same thermo-mechanical processing conditions showed that their properties are at the same level.

Microstructure and fracture toughness of electron beam welded joints of 30CrMnSiNi2A steel

Two post weld heat treatments (PWHT), 900 ℃ oil quenched and low temperature tempered (PWHTA) and high temperature tempered and then 900 ℃ oil quenched and low temperature tempered (PWHTB), are employed to treat the weldment. Then the effect of two post weld heat treatment processes on the microstructure,mechanical properties and fracture toughness of electron beam welded joints of 30CrMnSiNi2A steel have been discussed. The results show that, after two kinds of PWHT the microstructure and hardness at every zones of EBW joints are nearly same. Although the welds have good mechanical properties, fracture toughness of both weld and heat affected zone (HAZ) is low, the CTOD values of welds are comparatively higher than that of HAZ. Microstructure and fracture toughness of two EBW joints have no evident differences.

EFFECT OF WELDING THERMAL CYCLE ON THE MICROSTRUCTURE AND TOUGHNESS OF LOW ALLOY HIGH STRENGTH STEEL

Weldingthermalcyclicsimulated techniquesisemployed in thestudy. By meansof analysismetalloscope, fracture morphology and impact toughness test of the sample, the effect ofweldingthermalcycle peak temperature and dualthermal cycle on the micro structure and toughnessoflow alloy high strength steel HQ100 isinvestigated.Inner fine martensitic andbainitic microstrctureisobservedby TEM.Theresultsshow that withtheincreaseof peaktem perature, grain sizesbecomelarger,theimpacttoughness drop down .Ifthermalcycleisim posed twiceand dualthermalcyclicpeaktemperatureis1275 ℃+ 750 ℃,theimpacttoughnessisatthelowest value.Alsotheimpacttoughnessagrees withthefracture morphology.

Effect of Al in Ti－microalloyed Mn－Ni－Mo welding wire on microstructure and toughness of deposited metal

The effect of Al in Ti-microalloyed welding wire on microstructure and toughness of deposited metals is studied.The results show that the deposited metal toughness worsens with increasing Al in wire' The mechanism of Al is as follows:(1) Al makes oxygen content in deposited metal increase.(2)Al restrains the formation of Ti-rich oxide inclusion, which causes granular bainite microstructure in deposited metal.(3)The content of solute Ti in deposited metal increases with Al content in welding wire,as a result,a part of carbonrich constitution in deposited metal is in the form of twin martensite.

Microstructure and toughness of coarse grain heat-affected zone for Nb-microalloyed X80 pipeline steel

Based on welding thermal simulation on Nb-microaUoyed XSO pipeline stee! using Gleeble-3500 thermal simulation equipment, microstlttcture and impact toughness in coarse grain heat-affected zone （CGHAZ） under different welding parameters were investigated in this paper. The results show that high heat inputs with low preheats or low heat inputs with high preheats should be applied to achieve high impact toughness. Coarse original austenite grains may lower impact toughness. CGHAZ microstructure is mostly composed of upper bainite, granular bainite and lath bainite. The phase composition of microstructure and the quantity, size, shape of M/A constituents both have effects on impact toughness.

Microstructure and toughness of local brittle zone of HSLA steel multipass weld metals

By using thermo-simulation,Auger analysis and Charpy Ⅴ impact test and with the observation of the microstructures in which cleavage crack was initiated,the morphology and toughness of the local brittle zone of C-Mn and Cr-Ni-Mo multipass weld metals have been investigated.The results indicated that the local brittle zone in C-Mn weld metals with low and high Mn％ and Cr- Ni-Mo weld metals is different.With statistical analysis,it has been revealed that the more the local brittle zone and the lower their toughness,the lower the toughness of the entire weld metals.The alloy elements have a noticeable influ- ence on the toughness of the local brittle zone,thereby changing the toughness of weld metals.

Effect of Mn and Ni on Microstructure and Impact Toughness of Submerged Arc Weld Metals

The influences of Mn and Ni contents on the impact toughness and microstructure in the weld metals of high strength low alloy steels were studied. The objective of this study was to determine the optimum composition ranges of Mn and Ni to develop welding consumables with better resistance to cold cracking. The results indicated that Mn and Ni had considerable effect on the microstructure of weld metal, and both Mn and Ni promoted acicular ferrite at the expense of proeutectoid ferrite and ferrite side plates. Varying Ni content influenced the Charpy impact energy, the extent of which depended on Mn content. Based on the properties and impact resistance, the optimum levels of Mn and Ni were suggested to be 0.6%—0.9%,, and 2.5%—3.5%, respectively. Additions beyond this limit promoted the formation of segregation structures and other microstructural features, which may be detrimental to weld metal toughness.