A 28/56 Gb/s NRZ/PAM-4 dual-mode transceiver(TRx)designed in a 28-nm complementary metal-oxide-semiconduc-tor(CMOS)process is presented in this article.A voltage-mode(VM)driver featuring a 4-tap reconfigurable feed-fo...A 28/56 Gb/s NRZ/PAM-4 dual-mode transceiver(TRx)designed in a 28-nm complementary metal-oxide-semiconduc-tor(CMOS)process is presented in this article.A voltage-mode(VM)driver featuring a 4-tap reconfigurable feed-forward equal-izer(FFE)is employed in the quarter-rate transmitter(TX).The half-rate receiver(RX)incorporates a continuous-time linear equal-izer(CTLE),a 3-stage high-speed slicer with multi-clock-phase sampling,and a clock and data recovery(CDR).The experimen-tal results show that the TRx operates at a maximum speed of 56 Gb/s with chip-on board(COB)assembly.The 28 Gb/s NRZ eye diagram shows a far-end vertical eye opening of 210 mV with an output amplitude of 351 mV single-ended and the 56 Gb/s PAM-4 eye diagram exhibits far-end eye opening of 33 mV(upper-eye),31 mV(mid-eye),and 28 mV(lower-eye)with an output amplitude of 353 mV single-ended.The recovered 14 GHz clock from the RX exhibits random jitter(RJ)of 469 fs and deterministic jitter(DJ)of 8.76 ps.The 875 Mb/s de-multiplexed data features 593 ps horizontal eye opening with 32.02 ps RJ,at bit-error rate(BER)of 10-5(0.53 UI).The power dissipation of TX and RX are 125 and 181.4 mW,respectively,from a 0.9-V sup-ply.展开更多
With the explosive development of artificial intelligence(AI),machine learning(ML),and high-performance comput-ing(HPC),the ever-growing data movement is asking for high density interconnects with higher bandwidth(BW)...With the explosive development of artificial intelligence(AI),machine learning(ML),and high-performance comput-ing(HPC),the ever-growing data movement is asking for high density interconnects with higher bandwidth(BW),lower power and lower latency[1−3].The optical I/O leverages silicon photonic(SiPh)technology to enable high-density large-scale integrated photonics.展开更多
This article presents an 8-element dual-polarized phased-array transceiver(TRX)front-end IC for millimeter-wave(mm-Wave)5G new radio(NR).Power enhancement technologies for power amplifiers(PA)in mm-Wave 5G phased-arra...This article presents an 8-element dual-polarized phased-array transceiver(TRX)front-end IC for millimeter-wave(mm-Wave)5G new radio(NR).Power enhancement technologies for power amplifiers(PA)in mm-Wave 5G phased-array TRX are discussed.A four-stage wideband high-power class-AB PA with distributed-active-transformer(DAT)power combining and multi-stage second-harmonic traps is proposed,ensuring the mitigated amplitude-to-phase(AM-PM)distortions across wide carrier frequencies without degrading transmitting(TX)power,gain and efficiency.TX and receiving(RX)switching is achieved by a matching network co-designed on-chip T/R switch.In each TRX element,6-bit 360°phase shifting and 6-bit 31.5-dB gain tuning are respectively achieved by the digital-controlled vector-modulated phase shifter(VMPS)and differential attenuator(ATT).Fabricated in 65-nm bulk complementary metal oxide semiconductor(CMOS),the proposed TRX demonstrates the measured peak TX/RX gains of 25.5/21.3 dB,covering the 24−29.5 GHz band.The measured peak TX OP1dB and power-added efficiency(PAE)are 20.8 dBm and 21.1%,respectively.The measured minimum RX NF is 4.1 dB.The TRX achieves an output power of 11.0−12.4 dBm and error vector magnitude(EVM)of 5%with 400-MHz 5G NR FR2 OFDM 64-QAM signals across 24−29.5 GHz,covering 3GPP 5G NR FR2 operating bands of n257,n258,and n261.展开更多
Unmanned aerial vehicles(UAVs)may be subjected to unintentional radio frequency interference(RFI)or hostile jamming attack which will lead to fail to track global navigation satellite system(GNSS)signals.Therefore,the...Unmanned aerial vehicles(UAVs)may be subjected to unintentional radio frequency interference(RFI)or hostile jamming attack which will lead to fail to track global navigation satellite system(GNSS)signals.Therefore,the simultaneous realization of anti-jamming and high-precision carrier phase difference positioning becomes a dilemmatic problem.In this paper,a distortionless phase digital beamforming(DBF)algorithm with self-calibration antenna arrays is proposed,which enables to obtain distortionless carrier phase while suppressing jamming.Additionally,architecture of high precision Beidou receiver based on anti-jamming antenna arrays is proposed.Finally,the performance of the algorithm is evaluated,including antenna calibration accuracy,carrier phase distortionless accuracy,and carrier phase measurement accuracy without jamming.Meanwhile,the maximal jamming to signal ratio(JSR)and real time kinematic(RTK)positioning accuracy under wideband jamming are also investigated.The experimental results based on the real-life Beidou signals show that the proposed method has an excellent performance for precise relative positioning under jamming when compared with other anti-jamming methods.展开更多
Aiming at evaluating and predicting rapidly and accurately a high sensitivity receiver’s adaptability in complex electromagnetic environments,a novel testing and prediction method based on dual-channel multi-frequenc...Aiming at evaluating and predicting rapidly and accurately a high sensitivity receiver’s adaptability in complex electromagnetic environments,a novel testing and prediction method based on dual-channel multi-frequency is proposed to improve the traditional two-tone test.Firstly,two signal generators are used to generate signals at the radio frequency(RF)by frequency scanning,and then a rapid measurement at the intermediate frequency(IF)output port is carried out to obtain a huge amount of sample data for the subsequent analysis.Secondly,the IF output response data are modeled and analyzed to construct the linear and nonlinear response constraint equations in the frequency domain and prediction models in the power domain,which provide the theoretical criteria for interpreting and predicting electromagnetic susceptibility(EMS)of the receiver.An experiment performed on a radar receiver confirms the reliability of the method proposed in this paper.It shows that the interference of each harmonic frequency and each order to the receiver can be identified and predicted with the sensitivity model.Based on this,fast and comprehensive evaluation and prediction of the receiver’s EMS in complex environment can be efficiently realized.展开更多
Wideband spectrum sensing with a high-speed analog-digital converter(ADC) presents a challenge for practical systems.The Nyquist folding receiver(NYFR) is a promising scheme for achieving cost-effective real-time spec...Wideband spectrum sensing with a high-speed analog-digital converter(ADC) presents a challenge for practical systems.The Nyquist folding receiver(NYFR) is a promising scheme for achieving cost-effective real-time spectrum sensing,which is subject to the complexity of processing the modulated outputs.In this case,a multipath NYFR architecture with a step-sampling rate for the different paths is proposed.The different numbers of digital channels for each path are designed based on the Chinese remainder theorem(CRT).Then,the detectable frequency range is divided into multiple frequency grids,and the Nyquist zone(NZ) of the input can be obtained by sensing these grids.Thus,high-precision parameter estimation is performed by utilizing the NYFR characteristics.Compared with the existing methods,the scheme proposed in this paper overcomes the challenge of NZ estimation,information damage,many computations,low accuracy,and high false alarm probability.Comparative simulation experiments verify the effectiveness of the proposed architecture in this paper.展开更多
We collected high-quality teleseismic events recorded by 12 broadband seismographs deployed in the Anyuan Coal Mine and its adjacent areas in Pingxiang City,Jiangxi Province for nearly two years.The H-κ-c stacking me...We collected high-quality teleseismic events recorded by 12 broadband seismographs deployed in the Anyuan Coal Mine and its adjacent areas in Pingxiang City,Jiangxi Province for nearly two years.The H-κ-c stacking method was employed to obtain the crustal thickness and Poisson's ratio distribution,then the characteristics of crustal structure below the stations were obtained by using the time-domain linear inversion method.The crustal thickness in the Anyuan Coal Mine and its adjacent areas ranges from approximately 32~35 km,with an average thickness of 33 km,which is consistent with the crustal thickness results in South China from previous studies using the receiver function method.The average Poisson's ratio of the crustal bulk composition in the study area varies between 0.22 and 0.25,which is lower than the global value with a 0.27 average,indicating a predominantly intermediate-acidic or felsic crustal composition.There is a weak negative correlation between Poisson's ratio and crustal thickness estimates in the Anyuan Coal Mine and its adjacent areas,suggesting that the absence of mafic-ultramafic materials in the lower crust is associated with the process of crustal delamination.The velocity inversion results indicate that the crustal structure including three velocity discontinuity interfaces,with the first at a depth of approximately 1.5 km,the second at about 10~15 km,and the third being the Moho.The study also indicates that the results obtained by the H-κ-c stacking method are significantly better than those obtained by the H-κmethod,effectively reducing the standard deviation and dispersion of crustal thickness and vP/vSratio.展开更多
Lithospheric structure beneath the northeastern Qinghai-Xizang Plateau is of vital significance for studying the geodynamic processes of crustal thickening and expansion of the Qinghai-Xizang Plateau. We conducted a j...Lithospheric structure beneath the northeastern Qinghai-Xizang Plateau is of vital significance for studying the geodynamic processes of crustal thickening and expansion of the Qinghai-Xizang Plateau. We conducted a joint inversion of receiver functions and surface wave dispersions with P-wave velocity constraints using data from the Chin Array Ⅱ temporary stations deployed across the Qinghai-Xizang Plateau. Prior to joint inversion, we applied the H-κ-c method(Li JT et al., 2019) to the receiver function data in order to correct for the back-azimuthal variations in the arrival times of Ps phases and crustal multiples caused by crustal anisotropy and dipping interfaces. High-resolution images of vS, crustal thickness, and vP/vSstructures in the Qinghai-Xizang Plateau were simultaneously derived from the joint inversion. The seismic images reveal that crustal thickness decreases outward from the Qinghai-Xizang Plateau. The stable interiors of the Ordos and Alxa blocks exhibited higher velocities and lower crustal vP/vSratios. While, lower velocities and higher vP/vSratios were observed beneath the Qilian Orogen and Songpan-Ganzi terrane(SPGZ), which are geologically active and mechanically weak, especially in the mid-lower crust.Delamination or thermal erosion of the lithosphere triggered by hot asthenospheric flow contributes to the observed uppermost mantle low-velocity zones(LVZs) in the SPGZ. The crustal thickness, vS, and vP/vSratios suggest that whole lithospheric shortening is a plausible mechanism for crustal thickening in the Qinghai-Xizang Plateau, supporting the idea of coupled lithospheric-scale deformation in this region.展开更多
There are numerous applications, such as Radar, that leverage wideband technology. However, the presence of noise introduces certain limitations and challenges. It is crucial to harness wideband technology for applica...There are numerous applications, such as Radar, that leverage wideband technology. However, the presence of noise introduces certain limitations and challenges. It is crucial to harness wideband technology for applications demanding the rapid and precise transmission of diverse information from one point to another within a short timeframe. The ability to report a signal without tuning within the input bandwidth stands out as one of the advantages of employing a digital wideband receiver. As indicated, a digital wideband receiver plays a pivotal role in achieving high precision and accuracy. The primary distinction between Analog and Digital Instantaneous Frequency Measurement lies in the fact that analog Instantaneous Frequency Measurement (IFM) receivers have traditionally covered extensive input bandwidths, reporting one accurate frequency per short pulse. In the contemporary landscape, digital IFM systems utilize high-sampling-rate Analog-to-Digital Converters (ADC) along with Hilbert transforms to generate two output channels featuring a 90-degree phase shift. This paper explores the improvement of sensitivity in current digital IFM receivers. The optimization efforts target the Hilbert transform and autocorrelations architectures, aiming to refine the system’s ability to report fine frequencies within a noisy wide bandwidth environment, thereby elevating its overall sensitivity.展开更多
The Tian Shan is a vast range that spans several countries in Asia.Understanding its evolutionary history may provide valuable insights into intracontinental orogenic dynamics.In this study,we explored the crustal cha...The Tian Shan is a vast range that spans several countries in Asia.Understanding its evolutionary history may provide valuable insights into intracontinental orogenic dynamics.In this study,we explored the crustal characteristics of the Tian Shan and their relationships to the tectonic evolution of the region.A new H-stacking method that combines the P receiver function and gravity anomalies was used to estimate the thickness and ratio of P-to S-wave velocities(Vp/Vs)for 91 broadband seismic stations in the central and western Tian Shan.Our results revealed significant lateral variations in crustal thickness and Vp/Vs.A—45-km-thick crust and an intermediate-high Vp/Vs(-1.74-1.84)were found in the Kazakh Shield and Tarim Basin,which we interpreted to indicate a mafic crystalline basement and lower crust.The central Tian Shan varied greatly in crustal thickness(40-64 km)and Vp/Vs ratio(1.65-2.00).which may be due to crustal shortening,mafic underplating,and crustal melting.In contrast,we observed a relatively thin crust(42-50 km)with an intermediate Vp/Vs ratio(-1.78)in the western Tian Shan.The differences in the crustal structures between the western and central Tian Shan imply that the Talas-Fergana Fault may be trans-lithospheric.展开更多
Nyquist Folding Receiver(NYFR)is a perceptron structure that realizes a low probability of intercept(LPI)signal analog to information.Aiming at the problem of LPI radar signal receiving,the time domain,frequency domai...Nyquist Folding Receiver(NYFR)is a perceptron structure that realizes a low probability of intercept(LPI)signal analog to information.Aiming at the problem of LPI radar signal receiving,the time domain,frequency domain,and time-frequency domain problems of signals intercepted by NYFR structure are studied.Combined with the time-frequency analysis(TFA)method,a radar recognition scheme based on deep learning(DL)is introduced,which can reliably classify common LPI radar signals.First,the structure of NYFR and its characteristics in the time domain,frequency domain,and time and frequency domain are analyzed.Then,the received signal is then converted into a time-frequency image(TFI).Finally,four kinds of DL algorithms are used to classify LPI radar signals.Simulation results demonstrate the correctness of the NYFR structure,and the effectiveness of the proposed recognition method is verified by comparison experiments.展开更多
Thermoelectric generators(TEGs)are considered promising devices for waste heat recovery from various systems.The Seebeck effect can be utilized to generate power using the residual heat emitted by the filter dryer rec...Thermoelectric generators(TEGs)are considered promising devices for waste heat recovery from various systems.The Seebeck effect can be utilized to generate power using the residual heat emitted by the filter dryer receiver(FDR)of an air conditioning(A/C)system,which would otherwise go to waste.The study aims to build a set of thermoelectric generators(TEG)to collect the waste heat of the FDR and generate low-power electricity.A novel electrical circuit with two transformers is designed and fabricated to produce a more stable voltage for operation and charging.The thermoelectric generator(TEGs)was installed on the FDR of the A/C unit.The test showed that climate conditions have a significant impact on the output power generated from the system.The results showed that the peak voltage recorded in the current study is 5.2 V per day(wet,cold,and wind weather)with an output power of 0.2 W.These values are acceptable for powering the load and charging a single battery with 3.5 V as the voltage increases battery 0.1 V/20 min charge.A case study of operating the emergency signs in a building was considered.The current heat recovery system is deemed to be easily installed and can be connected to a network of TEGs to produce more power.展开更多
Radio frequency identification(RFID) is a ubiquitous identification technology nowadays. An on-chip high-performance transmit/receive(T/R) switch is designed and simulated in 0.13-μm CMOS technology for reader-less R...Radio frequency identification(RFID) is a ubiquitous identification technology nowadays. An on-chip high-performance transmit/receive(T/R) switch is designed and simulated in 0.13-μm CMOS technology for reader-less RFID tag. The switch utilizes only the transistor width and length(W/L) optimization, proper gate bias resistor and resistive body floating technique and therefore,exhibits 1 d B insertion loss, 31.5 d B isolation and 29.2 d Bm 1-d B compression point(P1d B). Moreover, the switch dissipates only786.7 n W power for 1.8/0 V control voltages and is capable of switching in 794 fs. Above all, as there is no inductor or capacitor used in the circuit, the size of the switch is 0.00208 mm2 only. This switch will be appropriate for reader-less RFID tag transceiver front-end as well as other wireless transceivers operated at 2.4 GHz band.展开更多
The study of inter-system bias(ISB)is important for multi-system fusion and the performance of different signal compatibility.In this paper,the stability of ISB at the BDS3/BDS2 receiver end is calculated and analyzed...The study of inter-system bias(ISB)is important for multi-system fusion and the performance of different signal compatibility.In this paper,the stability of ISB at the BDS3/BDS2 receiver end is calculated and analyzed for different time spans(DOY 060~090 in 2021)from a total of 31 MGEX and iGMAS stations.We adopted two estimation strategies,random walk and constant approach,using the precision products of orbit and clock bias provided by WUM,the influence of which on ISB was also analyzed.Our results showed that the ISB value varied little within a day,and the mean of daily ISB standard deviation was only 0.037 m when the observation condition was good.The signal reception was continuous,indicating a high ISB stability for one day.If extending the time series to one month,however,the ISB standard deviation calculated by constant approach,in which a constant ISB is estimated on a daily basis was about 0.1 m,and the results of adjacent days were not continuous,with no apparent pattern.Concerning the random walk approach,the obtained ISB time series also had a jump,and the conclusion was the same as that of the constant strategy.Besides,receiver types showed a strong regularity in ISB numerical situation,and the distribution of ISB values corresponding to the same receiver type was relatively close.Therefore,we conclude that the ISB parameters remain stable in the short term(one day)and less stable in the long-term period.It is recommended that the ISB term should be set as a constant estimate every day in BDS3/BDS2 solutions,regardless of receiver type consistency.展开更多
In planning and executing marine controlled-source electromagnetic methods, seafloor electromagnetic receivers must overcome the problems of noise, clock drift, and power consumption. To design a receiver that perform...In planning and executing marine controlled-source electromagnetic methods, seafloor electromagnetic receivers must overcome the problems of noise, clock drift, and power consumption. To design a receiver that performs well and overcomes the abovementioned problems, we performed forward modeling of the E-field abnormal response and established the receiver's characteristics. We describe the design optimization and the properties of each component, that is, low-noise induction coil sensor, low-noise Ag/AgCI electrode, low-noise chopper amplifier, digital temperature-compensated crystal oscillator module, acoustic telemetry modem, and burn wire system. Finally, we discuss the results of onshore and offshore field tests to show the effectiveness of the developed seafloor electromagnetic receiver and its performance: typical E-field noise of 0.12 nV/m/rt(Hz) at 0.5 Hz, dynamic range higher than 120 dB, clock drift lower than 1 ms/day, and continuous operation of at least 21 days.展开更多
This paper introduces a novel digital transceiver for the cordless telephone zero (CT0) standard,which uses a digital modulation and demodulation technique to handle the signal instead of the traditional analog meth...This paper introduces a novel digital transceiver for the cordless telephone zero (CT0) standard,which uses a digital modulation and demodulation technique to handle the signal instead of the traditional analog meth-od. In the transmitter,a fractional-N phase locked loop (PLL) is utilized to realize the continuous phase frequency shift key (CPFSK) modulation,and a 2 Ts raised cosine (2RC) shaping technique is used to reduce the occupied bandwidth. In the receiver,a novel digital method is proposed to demodulate the 2RC CPFSK signal. This chip is fabricated using an SMIC 0.35μm mixed signal CMOS process with a die size of 2mm × 2mm. With an external low noise amplifier (LNA),the sensitivity of the chip is better than -103dBm.展开更多
Based on the analyses of the reported Gilbert mixers operating at low supply vol tage,a down-conversion mixer and an up-conversion mixer for 2.4GHz bluetooth transceiver are presented with the modified low voltage de...Based on the analyses of the reported Gilbert mixers operating at low supply vol tage,a down-conversion mixer and an up-conversion mixer for 2.4GHz bluetooth transceiver are presented with the modified low voltage design techniques,respe ctively.Feedback and current mirror techniques suitable for low voltage operatio n are used to improve the linearity of the up-conversion mixer,and folded-casc ode output stage is adopted to optimize the noise and conversion gain of the dow n-conversion mixer operating at low voltage.Based on 0.35μm CMOS technology,s imulations are performed with 2V supply voltage.The results show that 20dBm thir d-order intercept point (IIP3),87mV output signal amplitude are achieved for up -conversion mixer with about 3mA current;while 20dB conversion gain (CG),6.5nV /Hz input-referred noise,4.4dBm IIP3 are obtained for down-conversion mixer with about 3.5mA current.展开更多
The development of a high performance wideband radio frequency (RF) transceiver used in the next generation mobile communication system is presented. The developed RF transceiver operates in the 6 to 6.3 GHz band an...The development of a high performance wideband radio frequency (RF) transceiver used in the next generation mobile communication system is presented. The developed RF transceiver operates in the 6 to 6.3 GHz band and the channel bandwidth is up to 100 MHz. It operates in the time division duplex (TDD) mode and supports the multiple-input multipleoutput (MIMO) technique for the international mobile telecommunications (IMT)-advanced systems. The classical superheterodyne scheme is employed to achieve optimal performance. Design issues of the essential components such as low noise amplifier, power amplifier and local oscillators are described in detail. Measurement results show that the maximum linear output power of the RF transceiver is above 23 dBm, and the gain and noise figure of the low noise amplifier is around 24 dB and below 1 dB, respectively. Furthermore, the error vector magnitude (EVM) measurement shows that the performance of the developed RF transceiver is well beyond the requirements of the long term evolution (LTE)-advanced system. With up to 8 x 8 MIMO configuration, the RF transceiver supports more than a 1 Gbit/s data rate in field tests.展开更多
A wideband monolithic optoelectronic integrated receiver with a high-speed photo-detector,completely compatible with standard CMOS processes,is designed and implemented in 0.6μm standard CMOS technology.The experimen...A wideband monolithic optoelectronic integrated receiver with a high-speed photo-detector,completely compatible with standard CMOS processes,is designed and implemented in 0.6μm standard CMOS technology.The experimental results demonstrate that its performance approaches applicable requirements,where the photo-detector achieves a -3dB frequency of 1.11GHz,and the receiver achieves a 3dB bandwidth of 733MHz and a sensitivity of -9dBm for λ=850nm at BER=10-12.展开更多
The design of a global positioning system (GPS) software receiver is introduced. This design uses the concept of software radio, and it consists of the following parts: front-end, acquisition, tracking, synchroniza...The design of a global positioning system (GPS) software receiver is introduced. This design uses the concept of software radio, and it consists of the following parts: front-end, acquisition, tracking, synchronization, navigation solution and some assisting modules. In the acquisition module, the acquisition algorithm based on circular correlation is utilized. The input data and the local code are converted into the frequency domain by means of the fast Fourier transform (FFT). After performing circular correlation, the initial phase of the C/A code can be obtained and the cartier frequency can be found in 1 kHz frequency resolution, which is too coarse to use for the tracking loop. In order to improve the frequency resolution, the fine frequency estimation through a phase relationship is then achieved, by which, the frequency resolution is improved dramatically. Experiments show that the inaccuracy of the carrier frequency can be estimated within a few hertz by the fine frequency estimation method, and the fine frequency attained can be directly used for the tracking loop.展开更多
基金supported by National Natural Science Foundation of China under Grant 62174132the Fundamental Research Funds for Central Universities under Grant xzy022022060.
文摘A 28/56 Gb/s NRZ/PAM-4 dual-mode transceiver(TRx)designed in a 28-nm complementary metal-oxide-semiconduc-tor(CMOS)process is presented in this article.A voltage-mode(VM)driver featuring a 4-tap reconfigurable feed-forward equal-izer(FFE)is employed in the quarter-rate transmitter(TX).The half-rate receiver(RX)incorporates a continuous-time linear equal-izer(CTLE),a 3-stage high-speed slicer with multi-clock-phase sampling,and a clock and data recovery(CDR).The experimen-tal results show that the TRx operates at a maximum speed of 56 Gb/s with chip-on board(COB)assembly.The 28 Gb/s NRZ eye diagram shows a far-end vertical eye opening of 210 mV with an output amplitude of 351 mV single-ended and the 56 Gb/s PAM-4 eye diagram exhibits far-end eye opening of 33 mV(upper-eye),31 mV(mid-eye),and 28 mV(lower-eye)with an output amplitude of 353 mV single-ended.The recovered 14 GHz clock from the RX exhibits random jitter(RJ)of 469 fs and deterministic jitter(DJ)of 8.76 ps.The 875 Mb/s de-multiplexed data features 593 ps horizontal eye opening with 32.02 ps RJ,at bit-error rate(BER)of 10-5(0.53 UI).The power dissipation of TX and RX are 125 and 181.4 mW,respectively,from a 0.9-V sup-ply.
基金This work was supported by the National Natural Science Foundation of China(Grant Nos.61925505,92373209 and 62235017).
文摘With the explosive development of artificial intelligence(AI),machine learning(ML),and high-performance comput-ing(HPC),the ever-growing data movement is asking for high density interconnects with higher bandwidth(BW),lower power and lower latency[1−3].The optical I/O leverages silicon photonic(SiPh)technology to enable high-density large-scale integrated photonics.
基金This work was supported in part by the National Key Research and Development Program of China under Grant 2019YFB1803000in part by the Major Key Project of Peng Cheng Laboratory,Shenzhen,China,under Project PCL2021A01-2.
文摘This article presents an 8-element dual-polarized phased-array transceiver(TRX)front-end IC for millimeter-wave(mm-Wave)5G new radio(NR).Power enhancement technologies for power amplifiers(PA)in mm-Wave 5G phased-array TRX are discussed.A four-stage wideband high-power class-AB PA with distributed-active-transformer(DAT)power combining and multi-stage second-harmonic traps is proposed,ensuring the mitigated amplitude-to-phase(AM-PM)distortions across wide carrier frequencies without degrading transmitting(TX)power,gain and efficiency.TX and receiving(RX)switching is achieved by a matching network co-designed on-chip T/R switch.In each TRX element,6-bit 360°phase shifting and 6-bit 31.5-dB gain tuning are respectively achieved by the digital-controlled vector-modulated phase shifter(VMPS)and differential attenuator(ATT).Fabricated in 65-nm bulk complementary metal oxide semiconductor(CMOS),the proposed TRX demonstrates the measured peak TX/RX gains of 25.5/21.3 dB,covering the 24−29.5 GHz band.The measured peak TX OP1dB and power-added efficiency(PAE)are 20.8 dBm and 21.1%,respectively.The measured minimum RX NF is 4.1 dB.The TRX achieves an output power of 11.0−12.4 dBm and error vector magnitude(EVM)of 5%with 400-MHz 5G NR FR2 OFDM 64-QAM signals across 24−29.5 GHz,covering 3GPP 5G NR FR2 operating bands of n257,n258,and n261.
基金supported by the Key Research and Development Program of Science&Technology Department of Sichuan Province(2021YFG0155)the Technical Innovation Fund of Southwest China Institute of Electronic Technology(H21004.2).
文摘Unmanned aerial vehicles(UAVs)may be subjected to unintentional radio frequency interference(RFI)or hostile jamming attack which will lead to fail to track global navigation satellite system(GNSS)signals.Therefore,the simultaneous realization of anti-jamming and high-precision carrier phase difference positioning becomes a dilemmatic problem.In this paper,a distortionless phase digital beamforming(DBF)algorithm with self-calibration antenna arrays is proposed,which enables to obtain distortionless carrier phase while suppressing jamming.Additionally,architecture of high precision Beidou receiver based on anti-jamming antenna arrays is proposed.Finally,the performance of the algorithm is evaluated,including antenna calibration accuracy,carrier phase distortionless accuracy,and carrier phase measurement accuracy without jamming.Meanwhile,the maximal jamming to signal ratio(JSR)and real time kinematic(RTK)positioning accuracy under wideband jamming are also investigated.The experimental results based on the real-life Beidou signals show that the proposed method has an excellent performance for precise relative positioning under jamming when compared with other anti-jamming methods.
基金supported by the National Natural Science Foundation of China(62071473).
文摘Aiming at evaluating and predicting rapidly and accurately a high sensitivity receiver’s adaptability in complex electromagnetic environments,a novel testing and prediction method based on dual-channel multi-frequency is proposed to improve the traditional two-tone test.Firstly,two signal generators are used to generate signals at the radio frequency(RF)by frequency scanning,and then a rapid measurement at the intermediate frequency(IF)output port is carried out to obtain a huge amount of sample data for the subsequent analysis.Secondly,the IF output response data are modeled and analyzed to construct the linear and nonlinear response constraint equations in the frequency domain and prediction models in the power domain,which provide the theoretical criteria for interpreting and predicting electromagnetic susceptibility(EMS)of the receiver.An experiment performed on a radar receiver confirms the reliability of the method proposed in this paper.It shows that the interference of each harmonic frequency and each order to the receiver can be identified and predicted with the sensitivity model.Based on this,fast and comprehensive evaluation and prediction of the receiver’s EMS in complex environment can be efficiently realized.
基金supported by the Key Projects of the 2022 National Defense Science and Technology Foundation Strengthening Plan 173 (Grant No.2022-173ZD-010)the Equipment PreResearch Foundation of The State Key Laboratory (Grant No.6142101200204)。
文摘Wideband spectrum sensing with a high-speed analog-digital converter(ADC) presents a challenge for practical systems.The Nyquist folding receiver(NYFR) is a promising scheme for achieving cost-effective real-time spectrum sensing,which is subject to the complexity of processing the modulated outputs.In this case,a multipath NYFR architecture with a step-sampling rate for the different paths is proposed.The different numbers of digital channels for each path are designed based on the Chinese remainder theorem(CRT).Then,the detectable frequency range is divided into multiple frequency grids,and the Nyquist zone(NZ) of the input can be obtained by sensing these grids.Thus,high-precision parameter estimation is performed by utilizing the NYFR characteristics.Compared with the existing methods,the scheme proposed in this paper overcomes the challenge of NZ estimation,information damage,many computations,low accuracy,and high false alarm probability.Comparative simulation experiments verify the effectiveness of the proposed architecture in this paper.
基金supported by the Spark Program of Earthquake Technology of CEA,China(XH20032)open Research Project from the State Key Laboratory of Nuclear Resources and Environment,East China University of Technology(2022NRE17)+1 种基金open Research Project from the State Key Laboratory of Geological Processes,Mineral Resources,China University of Geosciences(GPMR202114)the Graduate Student Innovation Fund of East China University of Technology(YC2022-s628)。
文摘We collected high-quality teleseismic events recorded by 12 broadband seismographs deployed in the Anyuan Coal Mine and its adjacent areas in Pingxiang City,Jiangxi Province for nearly two years.The H-κ-c stacking method was employed to obtain the crustal thickness and Poisson's ratio distribution,then the characteristics of crustal structure below the stations were obtained by using the time-domain linear inversion method.The crustal thickness in the Anyuan Coal Mine and its adjacent areas ranges from approximately 32~35 km,with an average thickness of 33 km,which is consistent with the crustal thickness results in South China from previous studies using the receiver function method.The average Poisson's ratio of the crustal bulk composition in the study area varies between 0.22 and 0.25,which is lower than the global value with a 0.27 average,indicating a predominantly intermediate-acidic or felsic crustal composition.There is a weak negative correlation between Poisson's ratio and crustal thickness estimates in the Anyuan Coal Mine and its adjacent areas,suggesting that the absence of mafic-ultramafic materials in the lower crust is associated with the process of crustal delamination.The velocity inversion results indicate that the crustal structure including three velocity discontinuity interfaces,with the first at a depth of approximately 1.5 km,the second at about 10~15 km,and the third being the Moho.The study also indicates that the results obtained by the H-κ-c stacking method are significantly better than those obtained by the H-κmethod,effectively reducing the standard deviation and dispersion of crustal thickness and vP/vSratio.
基金supported by the Natural Science Basic Research Program of Shaanxi(No.2023-JC-QN-0306)the Special Fund of the Institute of Geophysics,China Earthquake Administration(No.DQJB21B32)the National Natural Science Foundation of China(No.42174069).
文摘Lithospheric structure beneath the northeastern Qinghai-Xizang Plateau is of vital significance for studying the geodynamic processes of crustal thickening and expansion of the Qinghai-Xizang Plateau. We conducted a joint inversion of receiver functions and surface wave dispersions with P-wave velocity constraints using data from the Chin Array Ⅱ temporary stations deployed across the Qinghai-Xizang Plateau. Prior to joint inversion, we applied the H-κ-c method(Li JT et al., 2019) to the receiver function data in order to correct for the back-azimuthal variations in the arrival times of Ps phases and crustal multiples caused by crustal anisotropy and dipping interfaces. High-resolution images of vS, crustal thickness, and vP/vSstructures in the Qinghai-Xizang Plateau were simultaneously derived from the joint inversion. The seismic images reveal that crustal thickness decreases outward from the Qinghai-Xizang Plateau. The stable interiors of the Ordos and Alxa blocks exhibited higher velocities and lower crustal vP/vSratios. While, lower velocities and higher vP/vSratios were observed beneath the Qilian Orogen and Songpan-Ganzi terrane(SPGZ), which are geologically active and mechanically weak, especially in the mid-lower crust.Delamination or thermal erosion of the lithosphere triggered by hot asthenospheric flow contributes to the observed uppermost mantle low-velocity zones(LVZs) in the SPGZ. The crustal thickness, vS, and vP/vSratios suggest that whole lithospheric shortening is a plausible mechanism for crustal thickening in the Qinghai-Xizang Plateau, supporting the idea of coupled lithospheric-scale deformation in this region.
文摘There are numerous applications, such as Radar, that leverage wideband technology. However, the presence of noise introduces certain limitations and challenges. It is crucial to harness wideband technology for applications demanding the rapid and precise transmission of diverse information from one point to another within a short timeframe. The ability to report a signal without tuning within the input bandwidth stands out as one of the advantages of employing a digital wideband receiver. As indicated, a digital wideband receiver plays a pivotal role in achieving high precision and accuracy. The primary distinction between Analog and Digital Instantaneous Frequency Measurement lies in the fact that analog Instantaneous Frequency Measurement (IFM) receivers have traditionally covered extensive input bandwidths, reporting one accurate frequency per short pulse. In the contemporary landscape, digital IFM systems utilize high-sampling-rate Analog-to-Digital Converters (ADC) along with Hilbert transforms to generate two output channels featuring a 90-degree phase shift. This paper explores the improvement of sensitivity in current digital IFM receivers. The optimization efforts target the Hilbert transform and autocorrelations architectures, aiming to refine the system’s ability to report fine frequencies within a noisy wide bandwidth environment, thereby elevating its overall sensitivity.
基金supported by the National Science Foundation of China (Nos. U1839210, 41874097, 41474072, and 41874108)
文摘The Tian Shan is a vast range that spans several countries in Asia.Understanding its evolutionary history may provide valuable insights into intracontinental orogenic dynamics.In this study,we explored the crustal characteristics of the Tian Shan and their relationships to the tectonic evolution of the region.A new H-stacking method that combines the P receiver function and gravity anomalies was used to estimate the thickness and ratio of P-to S-wave velocities(Vp/Vs)for 91 broadband seismic stations in the central and western Tian Shan.Our results revealed significant lateral variations in crustal thickness and Vp/Vs.A—45-km-thick crust and an intermediate-high Vp/Vs(-1.74-1.84)were found in the Kazakh Shield and Tarim Basin,which we interpreted to indicate a mafic crystalline basement and lower crust.The central Tian Shan varied greatly in crustal thickness(40-64 km)and Vp/Vs ratio(1.65-2.00).which may be due to crustal shortening,mafic underplating,and crustal melting.In contrast,we observed a relatively thin crust(42-50 km)with an intermediate Vp/Vs ratio(-1.78)in the western Tian Shan.The differences in the crustal structures between the western and central Tian Shan imply that the Talas-Fergana Fault may be trans-lithospheric.
基金supported by the National Defence Pre-research Foundation of China。
文摘Nyquist Folding Receiver(NYFR)is a perceptron structure that realizes a low probability of intercept(LPI)signal analog to information.Aiming at the problem of LPI radar signal receiving,the time domain,frequency domain,and time-frequency domain problems of signals intercepted by NYFR structure are studied.Combined with the time-frequency analysis(TFA)method,a radar recognition scheme based on deep learning(DL)is introduced,which can reliably classify common LPI radar signals.First,the structure of NYFR and its characteristics in the time domain,frequency domain,and time and frequency domain are analyzed.Then,the received signal is then converted into a time-frequency image(TFI).Finally,four kinds of DL algorithms are used to classify LPI radar signals.Simulation results demonstrate the correctness of the NYFR structure,and the effectiveness of the proposed recognition method is verified by comparison experiments.
文摘Thermoelectric generators(TEGs)are considered promising devices for waste heat recovery from various systems.The Seebeck effect can be utilized to generate power using the residual heat emitted by the filter dryer receiver(FDR)of an air conditioning(A/C)system,which would otherwise go to waste.The study aims to build a set of thermoelectric generators(TEG)to collect the waste heat of the FDR and generate low-power electricity.A novel electrical circuit with two transformers is designed and fabricated to produce a more stable voltage for operation and charging.The thermoelectric generator(TEGs)was installed on the FDR of the A/C unit.The test showed that climate conditions have a significant impact on the output power generated from the system.The results showed that the peak voltage recorded in the current study is 5.2 V per day(wet,cold,and wind weather)with an output power of 0.2 W.These values are acceptable for powering the load and charging a single battery with 3.5 V as the voltage increases battery 0.1 V/20 min charge.A case study of operating the emergency signs in a building was considered.The current heat recovery system is deemed to be easily installed and can be connected to a network of TEGs to produce more power.
基金supported by the research grant Economic Transformation Programme (ETP-2013-037) from Universiti Kebangsaan Malaysia and the Ministry of Science, Technology and Innovation (MOSTI) respectively
文摘Radio frequency identification(RFID) is a ubiquitous identification technology nowadays. An on-chip high-performance transmit/receive(T/R) switch is designed and simulated in 0.13-μm CMOS technology for reader-less RFID tag. The switch utilizes only the transistor width and length(W/L) optimization, proper gate bias resistor and resistive body floating technique and therefore,exhibits 1 d B insertion loss, 31.5 d B isolation and 29.2 d Bm 1-d B compression point(P1d B). Moreover, the switch dissipates only786.7 n W power for 1.8/0 V control voltages and is capable of switching in 794 fs. Above all, as there is no inductor or capacitor used in the circuit, the size of the switch is 0.00208 mm2 only. This switch will be appropriate for reader-less RFID tag transceiver front-end as well as other wireless transceivers operated at 2.4 GHz band.
基金the Natural Science Innovation Group Foundation of China under Grants NO.41721003the Science and Technology Support Project of Department of Natural Resources of Hubei Province under Grants NO.ZRZY2022KJ29+1 种基金the Special Fund of Hubei Luojia Laboratory under Grants NO.220100020the National Natural Science Foundation of China under Grants NO.42174030.
文摘The study of inter-system bias(ISB)is important for multi-system fusion and the performance of different signal compatibility.In this paper,the stability of ISB at the BDS3/BDS2 receiver end is calculated and analyzed for different time spans(DOY 060~090 in 2021)from a total of 31 MGEX and iGMAS stations.We adopted two estimation strategies,random walk and constant approach,using the precision products of orbit and clock bias provided by WUM,the influence of which on ISB was also analyzed.Our results showed that the ISB value varied little within a day,and the mean of daily ISB standard deviation was only 0.037 m when the observation condition was good.The signal reception was continuous,indicating a high ISB stability for one day.If extending the time series to one month,however,the ISB standard deviation calculated by constant approach,in which a constant ISB is estimated on a daily basis was about 0.1 m,and the results of adjacent days were not continuous,with no apparent pattern.Concerning the random walk approach,the obtained ISB time series also had a jump,and the conclusion was the same as that of the constant strategy.Besides,receiver types showed a strong regularity in ISB numerical situation,and the distribution of ISB values corresponding to the same receiver type was relatively close.Therefore,we conclude that the ISB parameters remain stable in the short term(one day)and less stable in the long-term period.It is recommended that the ISB term should be set as a constant estimate every day in BDS3/BDS2 solutions,regardless of receiver type consistency.
基金sponsored by the 863 Program(No.2009AA09A2012012AA09A201)+1 种基金China Geological Survey Project(No.201100307)the Fundamental Research Funds of the Ministry of Education for the Central Universities(No.2652011249)
文摘In planning and executing marine controlled-source electromagnetic methods, seafloor electromagnetic receivers must overcome the problems of noise, clock drift, and power consumption. To design a receiver that performs well and overcomes the abovementioned problems, we performed forward modeling of the E-field abnormal response and established the receiver's characteristics. We describe the design optimization and the properties of each component, that is, low-noise induction coil sensor, low-noise Ag/AgCI electrode, low-noise chopper amplifier, digital temperature-compensated crystal oscillator module, acoustic telemetry modem, and burn wire system. Finally, we discuss the results of onshore and offshore field tests to show the effectiveness of the developed seafloor electromagnetic receiver and its performance: typical E-field noise of 0.12 nV/m/rt(Hz) at 0.5 Hz, dynamic range higher than 120 dB, clock drift lower than 1 ms/day, and continuous operation of at least 21 days.
文摘This paper introduces a novel digital transceiver for the cordless telephone zero (CT0) standard,which uses a digital modulation and demodulation technique to handle the signal instead of the traditional analog meth-od. In the transmitter,a fractional-N phase locked loop (PLL) is utilized to realize the continuous phase frequency shift key (CPFSK) modulation,and a 2 Ts raised cosine (2RC) shaping technique is used to reduce the occupied bandwidth. In the receiver,a novel digital method is proposed to demodulate the 2RC CPFSK signal. This chip is fabricated using an SMIC 0.35μm mixed signal CMOS process with a die size of 2mm × 2mm. With an external low noise amplifier (LNA),the sensitivity of the chip is better than -103dBm.
文摘Based on the analyses of the reported Gilbert mixers operating at low supply vol tage,a down-conversion mixer and an up-conversion mixer for 2.4GHz bluetooth transceiver are presented with the modified low voltage design techniques,respe ctively.Feedback and current mirror techniques suitable for low voltage operatio n are used to improve the linearity of the up-conversion mixer,and folded-casc ode output stage is adopted to optimize the noise and conversion gain of the dow n-conversion mixer operating at low voltage.Based on 0.35μm CMOS technology,s imulations are performed with 2V supply voltage.The results show that 20dBm thir d-order intercept point (IIP3),87mV output signal amplitude are achieved for up -conversion mixer with about 3mA current;while 20dB conversion gain (CG),6.5nV /Hz input-referred noise,4.4dBm IIP3 are obtained for down-conversion mixer with about 3.5mA current.
基金The National Natural Science Foundation of China (No.60702027,60921063)the National Basic Research Program of China(973 Program)(No.2010CB327400)the National Science and Technology Major Project of Ministry of Science and Technology of China(No.2010ZX03007-001-01,2011ZX03004-001)
文摘The development of a high performance wideband radio frequency (RF) transceiver used in the next generation mobile communication system is presented. The developed RF transceiver operates in the 6 to 6.3 GHz band and the channel bandwidth is up to 100 MHz. It operates in the time division duplex (TDD) mode and supports the multiple-input multipleoutput (MIMO) technique for the international mobile telecommunications (IMT)-advanced systems. The classical superheterodyne scheme is employed to achieve optimal performance. Design issues of the essential components such as low noise amplifier, power amplifier and local oscillators are described in detail. Measurement results show that the maximum linear output power of the RF transceiver is above 23 dBm, and the gain and noise figure of the low noise amplifier is around 24 dB and below 1 dB, respectively. Furthermore, the error vector magnitude (EVM) measurement shows that the performance of the developed RF transceiver is well beyond the requirements of the long term evolution (LTE)-advanced system. With up to 8 x 8 MIMO configuration, the RF transceiver supports more than a 1 Gbit/s data rate in field tests.
文摘A wideband monolithic optoelectronic integrated receiver with a high-speed photo-detector,completely compatible with standard CMOS processes,is designed and implemented in 0.6μm standard CMOS technology.The experimental results demonstrate that its performance approaches applicable requirements,where the photo-detector achieves a -3dB frequency of 1.11GHz,and the receiver achieves a 3dB bandwidth of 733MHz and a sensitivity of -9dBm for λ=850nm at BER=10-12.
基金Program for New Century Excellent Talents in Universi-ty(No.NCET-06-0462)Excellent Young Teacher Foundation of SoutheastUniversity(No.4022001002).
文摘The design of a global positioning system (GPS) software receiver is introduced. This design uses the concept of software radio, and it consists of the following parts: front-end, acquisition, tracking, synchronization, navigation solution and some assisting modules. In the acquisition module, the acquisition algorithm based on circular correlation is utilized. The input data and the local code are converted into the frequency domain by means of the fast Fourier transform (FFT). After performing circular correlation, the initial phase of the C/A code can be obtained and the cartier frequency can be found in 1 kHz frequency resolution, which is too coarse to use for the tracking loop. In order to improve the frequency resolution, the fine frequency estimation through a phase relationship is then achieved, by which, the frequency resolution is improved dramatically. Experiments show that the inaccuracy of the carrier frequency can be estimated within a few hertz by the fine frequency estimation method, and the fine frequency attained can be directly used for the tracking loop.