A hardening load transfer function for rock bolts and its calibration using distributed fiber optic sensing

Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most of which are based on the global rock bolt response evaluated in pull-out tests.This paper presents a laboratory experimental setup aiming to capture the rock formation effect,while using distributed fiber optic sensing to quantify the effect of the confinement and the reinforcement pull-out behavior on a more local level.It is shown that the behavior along the sample itself varies,with certain points exhibiting stress drops with crack formation.Some edge effects related to the kinematic freedom of the grout to dilate are also observed.Regardless,it was found that the mid-level response is quite similar to the average response along the sample.The ability to characterize the variation of the response along the sample is one of the many advantages high-resolution fiber optic sensing allows in such investigations.The paper also offers a plasticity-based hardening load transfer function,representing a"slice"of the anchor.The paper describes in detail the development of the model and the calibration/determination of its parameters.The suggested model captures well the coupled behavior in which the pull-out process leads to an increase in the confining stress due to dilative behavior.

Numerical modelling of resonance mechanisms in jointed rocks using transfer functions

Resonance effects in parallel jointed rocks subject to stress waves are investigated using transfer functions,derived from signals generated through numerical modelling.Resonance is important for a range of engineering situations as it identifies the frequency of waves which will be favourably transmitted.Two different numerical methods are used for this study,adopting the finite difference method and the combined discrete element-finite difference method.The numerical models are validated by replicating results from previous studies.The two methods are found to behave similarly and show the same resonance effects;one operating at low frequency and the other operating at relatively high frequency.These resonance effects are interpreted in terms of simple physical systems and analytical equations are derived to predict the resonant frequencies of complex rock masses.Low frequency resonance is shown to be generated by a system synonymous with masses between springs,described as spring resonance,with an equal number of resonant frequencies as the number of blocks.High frequency resonance is generated through superposition of multiple reflected waves developing standing waves within intact blocks,described as superposition resonance.While resonance through superposition has previously been identified,resonance based on masses between springs has not been previously identified in jointed rocks.The findings of this study have implications for future analysis of multiple jointed rock masses,showing that a wave travelling through such materials can induce other modes of propagation of waves,i.e.spring resonance.

Heat and Mass Transfer on Non-Newtonian Peristaltic Flow in a Channel in Presence of Magnetic Field: Analytical and Numerical Analysis

A study has been arranged to investigate the flow of non-Newtonian fluid in a vertical asymmetrical channel using peristalsis. The porous medium allows the electrically conductive fluid to flow in the channel, while a uniform magnetic field is applied perpendicular to the flow direction. The analysis takes into account the combined influence of heat and mass transfer, including the effects of Soret and Dufour. The flow’s non-Newtonian behavior is characterized using a Casson rheological model. The fluid flow equations are examined within a wave frame of reference that has a wave velocity. The analytic solution is examined using long wavelengths and a small Reynolds number assumption. The stream function, temperature, concentration and heat transfer coefficient expressions are derived. The bvp4c function from MATLAB has been used to numerically solve the transformed equations. The flow characteristics have been analyzed using graphs to demonstrate the impacts of different parameters.

Transfer function modeling and analysis of the open-loop Buck converter using the fractional calculus

Based on the fact that the real inductor and the real capacitor are fractional order in nature and the fractional calculus,the transfer function modeling and analysis of the open-loop Buck converter in a continuous conduction mode（CCM） operation are carried out in this paper.The fractional order small signal model and the corresponding equivalent circuit of the open-loop Buck converter in a CCM operation are presented.The transfer functions from the input voltage to the output voltage,from the input voltage to the inductor current,from the duty cycle to the output voltage,from the duty cycle to the inductor current,and the output impedance of the open-loop Buck converter in CCM operation are derived,and their bode diagrams and step responses are calculated,respectively.It is found that all the derived fractional order transfer functions of the system are influenced by the fractional orders of the inductor and the capacitor.Finally,the realization of the fractional order inductor and the fractional order capacitor is designed,and the corresponding PSIM circuit simulation results of the open-loop Buck converter in CCM operation are given to confirm the correctness of the derivations and the theoretical analysis.

Analysis of the optical quality by determining the modulation transfer function for anterior corneal surface in myopes

AIM: To describe the characteristics of modulation transfer function (MTF) of anterior corneal surface, and obtain the the normal reference range of MTF at different spatial frequencies and optical zones of the anterior corneal surface in myopes. METHODS: Four hundred eyes from 200 patients were examined under SIRIUS corneal topography system. Phoenis analysis software was applied to simulate the MTF curves of anterior corneal surface at vertical and horizontal meridians at the 3, 4, 5, 6, 7mm optical zones of cornea. The MTF values at spatial frequencies of 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55 and 60 cycles/degree (c/d) were selected. RESULTS: The MTF curve of anterior corneal surface decreased rapidly from low to intermediate frequency (0-15cpd) at various optical zones of cornea, the value decreased to 0 slowly at higher frequency (>15cpd). With the increase of the optical zones of cornea, MTF curve decreased gradually. 3) In the range of 3 mm- 6 mm optical zones of the cornea, the MTF values measured at horizontal meridian were greater than the corresponding values at horizontal meridian of each spatial frequency, the difference was statistically significant (P<0.05). At 7 mm optical zones of cornea, the MTF values measured at horizontal meridian were less than the corresponding values at vertical meridian at 10-60 spatial frequencies (cpd), and the difference was statistically significant in 25, 30, 35, 40, 45, 50 cpd(P<0.05). CONCLUSION: MTF can be used to describe the imaging quality of optical systems at anterior corneal surface objectively in detail.

Modulation transfer function characteristic of uniform-doping transmission-mode GaAs/GaAlAs photocathode

The resolution characteristic can be obtained by the modulation transfer function （MTF） of a GaAs/GaA1As photocathode. After establishing the theoretical model of GaAs（100）-oriented atomic configuration and the formula for the ionized impurity scattering of the non-equilibrium carriers, this paper calculates the trajectories of photoelectrons in a photocathode. Thus the distribution of photoelectron spots on the emit-face is obtained, which is namely the point spread function. The MTF is obtained by Fourier transfer of the line spread function obtained from the point spread function. The MTF obtained from these calculations is shown to depend heavily on the electron diffusion length, and enhanced considerably by decreasing the electron diffusion length and increasing the doping concentration. Furthermore, the resolution is enhanced considerably by increasing the active-layer thickness, especially at high spatial frequencies. The best spatial resolution is 860 lp/mm, for the GaAs photocathode of doping concentration 1 ×10^19 cm 3 electron diffusion length 3.6 μm and the active-layer thickness 2 μm, under the 633-nm light irradiated. This research will contribute to the future improvement of the cathode＇s resolution for preparing a high performance GaAs photocathode, and improve the resolution of a low light level image intensifier.

Repetitive PD control strategy with inverse transfer function compensation for CVCF inverter

A novel repetitive control strategy for the output waveform of single-phase CVCF inverters is presented. In this scheme, the inverse transfer function of inverter is used as a compensator to obtain stable and satisfy harmonic rejection. Besides, PD controller is adopted to improve transient performance. Simulation and experimental results, which are gotten from a DSP-based 400Hz, 5.5KW inverter, indicate that the proposed control scheme can achieve not only low THD during steady-state operation but also fast transient response during load step change.

Establishment of a diatom-total phosphorus transfer function for lakes on the Songnen Plain in northeast China

To understand the relationship between planktonic diatoms and environmental variables in the lakes on the Songnen Plain,northeast(NE)China,we investigated water quality and planktonic diatoms from 71 sampling points in 27 lakes,based on which Canonical Correspondence Analysis(CCA)was conducted.The result show that planktonic diatoms displayed certain responses to environment gradients,and the total phosphorus(TP)explained the maximum variation of planktonic diatom species among the 15 environmental variables,suggesting that TP was the most important and significant environmental parameter affecting the distribution of diatom species.In addition,we established a diatom-total phosphorus transfer(DTPT)function,of which component 5 of the weighted averaging partial least squares regression(WAPLS)was chosen to and compared with a series of weighted average regression(WA)models and WA-PLS models.According to the jackknifing statistical test,the component 5 of WA-PLS models provided a lower root-mean-square error prediction(RMSEP=0.202)and a higher correlation coefficient between observation and prediction(R^2_Jack=0.759).After deletion of three outliers,the root-mean-square error prediction of the DTPT function was reduced(RMSEP=0.169)while the correlation coefficient between observation and prediction was increased(R^2_Jack=0.823).Therefore,this DTPT function performed better than other regional TP models in the world.However,it remains demanding for expanding the background dataset to improve the prediction ability of the model.

Mathematical simulations of the galvanic coupling intra-body communication by using the transfer function method

The galvanic coupling intra-body communication （IBC） was mathematically simulated based on the proposed transfer function. Firstly, a galvanic coupling IBC circuit model was developed and the corresponding parameters were discussed. Secondly, the transfer function of the galvanic coupling IBC was derived and proposed. Finally, the signal attenuation characteristics of the galvanic coupling IBC were measured along different signal transmission paths of actual human bodies, while the corresponding mathematical simulations based on the proposed transfer function were carried out. Our investigation showed that the mathematical simulation results coincided with the measured results over the frequency range of 100kHz to 5MHz, which indicated that the proposed transfer function could be useful for theoretical analysis and application of the galvanic coupling IBC.

Spectrum Characteristics and Transfer Function of the Hydrograph of the Deep Aqueous System

The fluctuation of most of the hydrograph in the deep aqueous system records the fluid pulsation in lithosphere and variation of the earth's crust. Many observations have verified that groundwater is an ideal information carrier of the crust. In this paper, the series of input (precipitation, air pressure, Earth tide etc.) and output (water level, artesian flow) of the deep aqueous system are studied by using the spectrum analysis and system theory. The application concepts of transfer function and the spectral structure of the hydrograph enrich the knowledge of the deep aqueous system. Two typical spectral structures of the hydrograph of the deep aqueous system are obtained by comparing with many water-bearing systems of the Jizhong depression. One is from well Ma-17 and the other is from the well Xinze-5. Finally, the physical models of forming the spectrum of the hydrograph are constructed on the basis of the spectrum research on the deep aqueous system.

Optical Transfer Function Reconstruction in Incoherent Fourier Ptychography

An optical transfer function （OTF） reconstruction model is first embedded into incoherent Fourier ptychography （IFP）. The leading result is a proposed algorithm that can recover both the super-resolution image and the OTF of an imaging system with unknown aberrations simultaneously. This model overcomes the difficult problem of OTF estimation that the previous IFP faces. The effectiveness of this algorithm is demonstrated by numerical simulations, and the superior reconstruction is presented. We believe that the reported algorithm can extend the original IFP for more complex conditions and may provide a solution by using structured light for characterization of optical systems＇ aberrations.

Transfer function measurement for the SSRF SRF system

A digital transfer function measurement system has been embedded in the low-level radio frequency (LLRF) system of the storage ring of the Shanghai Synchrotron Radiation Facility. The measurement results indicate that the decreased control accuracy at high current is primarily owing to ripples from the high-voltage power supply, the transient beam loading effect, and the digital aliasing effect. The current LLRF algorithm is not able to suppress these disturbances.

Temperature and Water Vapor Weighting Functions from Radiative Transfer Equation with Surface Emissivity and Solar Reflectivity

Linearization of Radiative Transfer Equation (RTE) is the key step in physical retrieval of atmospheric temperature and moisture profiles from InfRared (IR) sounder observations. In this paper, the successive forms of temperature and water vapor mixing ratio component weighting functions are derived by applying one term variation method to RTE with surface emissivity and solar reflectivity contained. Retrivals of temperature and water vapor mixing ratio profiles from simulated Atmospheric Infrared Sounder (AIRS) observations with surface emissivity and solar reflectivity are presented.

INTERPOLATION OF HEAD-RELATED TRANSFER FUNCTIONS USING SPHERICAL FOURIER EXPANSION

A new interpolation algorithm for Head-Related Transfer Function （HRTF） is proposed to realize 3D sound reproduction via headphones in arbitrary spatial direction. HRTFs are modeled as a weighted sum of spherical harmonics on a spherical surface. Truncated Singular Value Decomposition （SVD） is adopted to calculate the weights of the model. The truncation number is chosen according to Frobenius norm ratio and the partial condition number. Compared with other interpolated methods, our proposed approach not only is continuous but exploits global information of available directions. The HRTF from any desired direction can be and interpolated results demonstrate that our obtained more accurately and robustly. Reconstructed proposed algorithm acquired better performance.

Transfer Function Based Recognition of Resonance Overvoltages Transformer Windings

Power transformer insulation systems are subjected to many stresses during normal operation due to lightning and switching.If the spectrum of incoming surge voltage matches the winding one,the corresponding resonance will be excited.Therefore external transients occurring in power systems might trigger internal overvoltages with large maximum value in transformer windings.Overvoltages having such characteristic have been the root cause of many power transformer failures.The paper presents an approach to the identification of sensitive zones in the transformer windings based on the measurements of overvoltages inside windings and frequency dependences of admittance of the power transformer.The frequency characteristic of the transformer winding may determine those regions in the frequency spectrum.The presented approach might be used both for design optimization and diagnostics of distribution and power transformers.

SYNTHESIS OF THERMAL RESPONSE FACTORS AND Z-TRANSFER FUNCTION COEFFICIENTS FOR CALCULATION OF ROOM TEMPERATURE VARIATION

A new method is presented for getting the general thermal response factors and z-transfer functioncoefficients of a room by synthesizing them from the thermal response factors of different parts of the thermalinsulation structure. How to use the general thermal response factors and z-transfer function coefficients toca1culate the indoor air temperature variation directly is also studied. It is shown through practical use that it iseasy to program with the methods presented in this paper and the calculated results are reliable.

Grey GM(1,1) Model with Function-Transfer Method for Wear Trend Prediction and its Application

Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the existing known information is used to infer the unknown information's character, state and development trend in a fault pattern, and to make possible forecasting and decisions for future development. It involves the whitenization of a Grey process. But the traditional equal time interval Grey GM (1,1) model requires equal interval data and needs to bring about accumulating addition generation and reversion calculations. Its calculation is very complex. However, the non equal interval Grey GM (1,1) model decreases the condition of the primitive data when establishing a model, but its requirement is still higher and the data were pre processed. The abrasion primitive data of plant could not always satisfy these modeling requirements. Therefore, it establishes a division method suited for general data modeling and estimating parameters of GM (1,1), the standard error coefficient that was applied to judge accuracy height of the model was put forward; further, the function transform to forecast plant abrasion trend and assess GM (1,1) parameter was established. These two models need not pre process the primitive data. It is not only suited for equal interval data modeling, but also for non equal interval data modeling. Its calculation is simple and convenient to use. The oil spectrum analysis acted as an example. The two GM (1,1) models put forward in this paper and the new information model and its comprehensive usage were investigated. The example shows that the two models are simple and practical, and worth expanding and applying in plant fault diagnosis.

Color Image Enhancement by an Integral Mask-filtering Approach Employing Nonlinear Transfer Function

We demonstrate a brand-new method to sharpen a color image by using an integral mask-filtering technique. The derivatives between the target pixel and its neighbors are transferred by the cubic root function instead of the traditional linear one. The obtained final image has clearer fine characteristics along with much less overshooting.

Solving the atmospheric scattering optical transfer function using the multi-coupled single scattering method

The atmospheric scattering optical transfer function （OTF） is solved by applying the multi-coupled single scattering （MCSS） method to the three-dimensional radiative transfer equation （RTE） under the periodic ground condition. This approach is a direct hit to the atmospheric scattering OTF using the same original context of modulation transfer function （MTF） measurement, i.e., images of sinusoidal grating at different spatial frequencies. Both the amplitude and phase shift of the OTF at various zenith and azimuth angles can be obtained at an arbitrary spatial frequency.

The anomalous reactions of the geomagnetic horizontal field transfer functions before Tangshan earthquake

We have collected the data of variometers in period from 1972 through 1984 at Changli and Baijiatuan stations. The results calculated from 19 groups of data show: 1) There are no significant anomalies of A, B at Baijiatuan and that of B at Changli, but there are evident anomalous changes for A u, A v at Changli station. This result basically agrees to the a, b calculated using the method of measuring magnetograms, which demonstrates that the anomalies limited in the aftershock area and its neighbouring regions. 2) There are some changes of the inter station transfer functions of C u, C v, F u, F v before Tangshan earthquake, and the changes of the image parts C v, F v are more obvious, which is in agreement with the research results for Hualian earthquake. However, according to the results of Carlisle M =5.0 earthquake by Beamish(1982), the real parts F u, C u change more significantly.