Performance of composite foundations with different load transfer platforms and substratum stiffness over silty clay

The semi-rigid pile-supported composite foundation is widely used in highway projects due to its effectiveness in increasing the bearing capacity and stability of foundations.It is crucial to understand the stress distribution across the embankment width and the behaviour of unreinforced foundations.Thus,five centrifuge tests were conducted to examine the bearing and deformation behaviours of NPRS(Non-Connected Piled Raft Systems)and GRPS(GeosyntheticReinforced Pile-Supported systems)with varying substratum stiffness,then a comparative analysis was conducted on embankment settlement,pressures underneath the embankments,and axial forces along the piles.The results indicated that greater substratum stiffness correlates with reduced settlement and deformation at various depths.Deformation occurring 5 meters from the embankment toe includes settlement in NPRS and upward movement in GRPS.The potential sliding surface is primarily located within the embankment in NPRS,whereas it may extend through both the embankment and foundation in GRPS.The pile-soil stress ratio and efficiency in NPRS are higher than in GRPS across the embankment.The axial force borne by end-bearing piles is significantly greater than that by floating piles.As the buried depth increases,the axial force in GRPS initially rises then declines,whereas in NPRS,it remains relatively constant within a certain range before decreasing.This study aids in assessing the applicability of composite foundations in complex railway environments and provides a reference for procedural measures under similar conditions.

Numerical and theoretical study of load transfer behavior during cascading pillar failure

To further study the load transfer mechanism of roofemulti-pillarefloor system during cascading pillar failure(CPF),numerical simulation and theoretical analysis were carried out to study the three CPF modes according to the previous experimental study on treble-pillar specimens,e.g.successive failure mode(SFM),domino failure mode(DFM)and compound failure mode(CFM).Based on the finite element code rock failure process analysis(RFPA^(2D)),numerical models of treble-pillar specimen with different mechanical properties were established to reproduce and verify the experimental results of the three CPF modes.Numerical results show that the elastic rebound of roofefloor system induced by pillar instability causes dynamic disturbance to adjacent pillars,resulting in sudden load increases and sudden jump displacement of adjacent pillars.The phenomena of load transfer in the roofemulti-pillarefloor system,as well as the induced accelerated damage behavior in adjacent pillars,were discovered and studied.In addition,based on the catastrophe theory and the proposed mechanical model of treble-pillar specimen edisc spring group system,a potential function that characterizes the evolution characteristics of roof emulti-pillarefloor system was established.The analytical expressions of sudden jump and energy release of treble-pillar specimenedisc spring group system of the three CPF modes were derived according to the potential function.The numerical and theoretical results show good agreement with the experimental results.This study further reveals the physical essence of load transfer during CPF of roof emulti-pillarefloor system,which provides references for mine design,construction and disaster prevention.

Intelligent Power Grid Load Transferring Based on Safe Action-Correction Reinforcement Learning

When a line failure occurs in a power grid, a load transfer is implemented to reconfigure the network by changingthe states of tie-switches and load demands. Computation speed is one of the major performance indicators inpower grid load transfer, as a fast load transfer model can greatly reduce the economic loss of post-fault powergrids. In this study, a reinforcement learning method is developed based on a deep deterministic policy gradient.The tedious training process of the reinforcement learning model can be conducted offline, so the model showssatisfactory performance in real-time operation, indicating that it is suitable for fast load transfer. Consideringthat the reinforcement learning model performs poorly in satisfying safety constraints, a safe action-correctionframework is proposed to modify the learning model. In the framework, the action of load shedding is correctedaccording to sensitivity analysis results under a small discrete increment so as to match the constraints of line flowlimits. The results of case studies indicate that the proposed method is practical for fast and safe power grid loadtransfer.

Optimal allocation method of electric/air braking force of high-speed train considering axle load transfer

Reasonable distribution of braking force is a factor for a smooth,safe,and comfortable braking of trains.A dynamic optimal allocation strategy of electric-air braking force is proposed in this paper to solve the problem of the lack of consideration of adhesion difference of train wheelsets in the existing high-speed train electric-air braking force optimal allocation strategies.In this method,the braking strategy gives priority to the use of electric braking force.The force model of a single train in the braking process is analyzed to calculate the change of adhesion between the wheel and rail of each wheelset after axle load transfer,and then the adhesion of the train is estimated in real time.Next,with the goal of maximizing the total adhesion utilization ratio of trailer/motor vehicles,a linear programming distribution function is constructed.The proportional coefficient of adhesion utilization ratio of each train and the application upper limit of braking force in the function is updated according to the change time point of wheelset adhesion.Finally,the braking force is dynamically allocated.The simulation results of Matlab/Simulink show that the proposed algorithm not only uses the different adhesion limits of each trailer to reduce the total amount of braking force undertaken by the motor vehicle,but also considers the adhesion difference of each wheelset.The strategy can effectively reduce the risk and time of motor vehicles during the braking process and improve the stability of the train braking.

A priority-based dynamic load transfer algorithm for cellular/WLAN integrated networks

For the integration network of a cellular network and a wireless local area network （WLAN）, a priority-based dynamic load transfer （PDLT） algorithm is proposed. The dynamic vertical handoffs by call admission control are jointly determined by the network conditions and the traffic characteristics in combination with the location-condition of mobile terminals. When there is no bandwidth resource available in the cellular network or WLAN, the proposed PDLT algorithm allows an incoming voice call or data call within the overlapping area of the cellular network and the WLAN to be directed to the spare network; meanwhile, by dynamically computing the occupancy of the bandwidth resource, the proposed PDLT algorithm also allows an ongoing voice call or data communication to be transferred to the network with a sufficient bandwidth resource according to the given threshold to balance the number of voice/data calls in the two networks. The analysis results of a two-dimensional Markov model and the simulation results show that the PDLT algorithm can effectively enhance the whole integrated network＇ s traffic, reduce the blocking probability of new calls and increase the data throughput, and thus decrease the response time for various services.

Analytical method of load-transfer of single pile under expansive soil swelling

The elastic differential equations of load-transfer of single pile either with applied loads on pile-top or only under the soil swelling were established,respectively,based on the theory of pile-soil interaction and the shear-deformation method.The derivation of analytic solution to load-transfer for single pile in expansive soil could hereby be obtained by means of superposition principle under expansive soils swelling.The comparison of two engineering examples was made to prove the credibility of the suggested method.The analyzed results show that this analytic solution can achieve high precision with few parameters required,indicating its' simplicity and practicability in engineering application.The employed method can contribute to determining the greatest tension along pile shaft resulting from expansive soils swelling and provide reliable bases for engineering design.The method can be employed to obtain various distributive curves of axial force,settlements and skin friction along the pile shaft with the changes of active depth,vertical movements of the surface and loads of pile-top.

Optimization of the fully grouted rock bolts for load transfer enhancement

The purpose of this study is to investigate the role of bolt profile configuration in load transfer capacity between the bolt and grout.Therefore,five types of rock bolts are used with different profiles.The rock bolts are modeled by ANSYS software.Models show that profile rock bolt T_3 and T_ with load capacity 180 and 195 kN in the jointed rocks,are the optimum profiles.Finally,the performances of the selected profiles are examined in Tabas Coal Mine by FLAC software.There is good subscription between the results of numerical modeling and instrumentation reading such as tells tale,sonic extensometer and strain gauge rock bolt.According to the finding of this study,the proposed pattern of rock bolts,on 7 + 6 patterns per meter with 2 flexi bolt(4 m) for support gate road.

Vertical bearing capacity of pile based on load transfer model

The load transfer analytical method is applied to study the bearing mechanism of piles with vertical load in this paper. According to the different hardening rules of soil or rock around the pile shaft, such as work-softening, ideal elasto-plastic and work-hardening, a universal tri-linear load transfer model is suggested for the development of side and tip resistance by various types of soil (rock) with the consideration of sediment at the bottom of the pile. Based on the model, a formula is derived for the relationship between the settlement and load on the pile top to determine the vertical bearing capacity, taking into account such factors as the characteristics of the stratum, the side resistance along the shaft, and tip resistance under the pile tip. A close agreement of the calculated results with the measured data from a field test pile lends confidence to the future application of the present approach in engineering practice.

A hardening load transfer function for rock bolts and its calibration using distributed fiber optic sensing

Confinement of rock bolts by the surrounding rock formation has long been recognized as a positive contributor to the pull-out behavior,yet only a few experimental works and analytical models have been reported,most of which are based on the global rock bolt response evaluated in pull-out tests.This paper presents a laboratory experimental setup aiming to capture the rock formation effect,while using distributed fiber optic sensing to quantify the effect of the confinement and the reinforcement pull-out behavior on a more local level.It is shown that the behavior along the sample itself varies,with certain points exhibiting stress drops with crack formation.Some edge effects related to the kinematic freedom of the grout to dilate are also observed.Regardless,it was found that the mid-level response is quite similar to the average response along the sample.The ability to characterize the variation of the response along the sample is one of the many advantages high-resolution fiber optic sensing allows in such investigations.The paper also offers a plasticity-based hardening load transfer function,representing a"slice"of the anchor.The paper describes in detail the development of the model and the calibration/determination of its parameters.The suggested model captures well the coupled behavior in which the pull-out process leads to an increase in the confining stress due to dilative behavior.

Uplift behavior and load transfer mechanism of prestressed high-strength concrete piles

Prestressed high-strength-concrete (PHC) tube-shaped pile is one of the recently used foundations for soft soil. The research on uplift resistance of PHC pile is helpful to the design of pile foundations. A field-scale test program was conducted to study the uplift behavior and load transfer mechanism of PHC piles in soft soil. The pullout load tests were divided into two groups with different diameters, and there were three piles in each group. A detailed discussion of the axial load transfer and pile skin resistance distribution was also included. It is found from the tests that the uplift capacity increases with increasing the diameter of pile. When the diameter of piles increases from 500 to 600 mm, the uplift load is increased by 51.2%. According to the load-displacement (Q-S) curves, all the piles do not reach the ultimate state at the maximum load. The experimental results show that the piles still have uplift bearing capacity.

Load Transfer Test of Post-Tensioned Anchorage Zone in Ultra High Performance Concrete

Researches on ultra-high performance concrete (UHPC) have been conducted worldwide owing to its outstanding durability and strength performances. The exploitation of the mechanical properties of UHPC will render it possible to achieve economic design through substantial reduction in the cross sectional dimensions and simplification in the reinforcement arrangement. This paper investigates experimentally the load transfer in the prestressed concrete anchorage zone. To provide distinctive features of UHPC compared to ordinary concrete, the cross sectional dimensions of the member were reduced and the stress distribution, deformation and cracking pattern of the PS anchorage zone were examined experimentally according to the degree of reinforcement of the members chosen. The distributions of the bursting stress, spalling stress and longitudinal edge stress in the specimens were observed according to the various types of reinforcement. All the specimens satisfied the load-bearing capacity criterion specified by the European ETAG-013 guidelines and their stress distributions were similar to those in the PS anchorages of post-tensioned members applying ordinary concrete. The cracks propagated longitudinally with lengths up to twice the cross sectional dimensions and their width was smaller than when applying ordinary concrete owing to the bridging effect of the steel fibers in UHPC. Accordingly, the exploitation of the high strength of UHPC enabled us to secure the resistance of the anchorage with no need for particular reinforcing devices.

Quantification of the Vertical Load Applied to the Pavement during Cornering Maneuver of a Battery Electric Commercial Vehicle

The wheel loads of heavy trucks are the major source of pavement damage,given the repeated loadings imposed by them due to transient events and surface irregularities.While related studies focus on steady-state context regarding simplified vehicle’s parameters and ideal pavement conditions,this paper aims to analyze the vertical load applied to the pavement by considering cornering maneuver as a transient event,on a battery electric vehicle truck.In this concern,measurements were performed on a rigid truck,with two steering front axles,in a closed course proving ground.The relationship has been presented between vehicle’s speed,lateral acceleration and transferred vertical load for a given curve radius of 85.6 m and 3.7°of transversal slope.The measurements results indicated that for every 10 km/h increasing on the vehicle’s speed,additional 110 kgf will be transferred to the pavement on the outer side of the cornering radius.This value itself could not be considered high,but it will be also added to the static load,or overload in some truck applications.

Analysis of Capability Requirement of Dynamic Positioning System for Cargo Transfer Vessel at Sea

In response to the development of deep-sea oil and gas resources,which require a high degree of cooperation by crude oil transportation equipment,a new type of ship known as the cargo transfer vessel(CTV)has been developed.To provide a theoretical reference for the design and equipment of the CTV’s dynamic positioning system,in this paper,we take the new deepwater CTVas the study object and theoretically and numerically analyze its operation,wind load,current load,wave load,and navigational resistance in a range of Brazilian sea conditions with respect to its positioning and towing modes.We confirm that our proposed method can successfully calculate the total environmental load of the CTVand that the CTV is able to operate normally under the designed sea conditions.

Simulation and Experimental Design of Load Adaptive Braking System on Two Wheeler

The braking quality is considered the main execution of the adaptive control framework that impacts the vehicle safety and rides solace astoundingly notably the stopping distance.This research work aims to create a pattern and design of an electromechanically adjusted lever that multiplies the applied braking force depending on the inputs given by the sensors to reduce the stopping distance of the vehicle.It is carried out using two main parts of the two-wheeler vehicle:thefirst part deals with the detection of load acting on the vehicle and identifying the required braking force to be applied,and the second part deals with the micro-controller which activates the stepper motor for varying the mechanical leverage ratio from various loads on the vehicle using two actively movable wedges.The electromechanically operated variable braking force system is developed to actuate the braking system based on the load on the motorcycle.The MATLAB simulation and experimental work are carried out for various loading(driver and pillion)conditions on a two-wheeler.The results indicate that the proposed electronically operated braking system is more effective than the conventional braking system for various loads and vehicle speeds.Specifically,the stopping distance of the vehicle is decreased significantly by about 4.9%between the con-ventional braking system and the simulated proposed system.Further,the experi-mental results show that the stopping distance is condensed by about 4.1%.The validation between simulated and experimental results revealed a great deal with the least error percentage of about 0.8%.

Transfer function measurement for the SSRF SRF system

A digital transfer function measurement system has been embedded in the low-level radio frequency (LLRF) system of the storage ring of the Shanghai Synchrotron Radiation Facility. The measurement results indicate that the decreased control accuracy at high current is primarily owing to ripples from the high-voltage power supply, the transient beam loading effect, and the digital aliasing effect. The current LLRF algorithm is not able to suppress these disturbances.

Thermal Load Reduction with Green Building Envelope

Various studies have confirmed that high thermal resistance in roof & wall can reduce the heat transfer load of the buildings. In this study, experimental investigation of the effects of some sustainable features (such as green roof, reflective coated roof & Fly ash brick (FAB) etc.) on the building has been conducted in the Indian context. For the purpose, two scaled building models i.e. Model I (conventional design) & Model II (green design) have been examined with different design configurations. The sensible heat transfer (SHT) load of the building is reduced by 21% - 29% through the use of FAB with cavity wall in place of Fired clay brick (FCB) wall. The load reduction increases to 26% - 44% by using FAB cavity wall with reflective coating on the roof. This reduction further increases to 64% - 68% with FAB cavity wall along with green roof. In this final scenario, the monthly electrical energy saving for air-conditioning is approximately 5.1 kWhe/m2 per unit envelope area, with associated reduction in GHG emissions up to 6.36 kg CO2eq/m2 per unit envelope area, assuming continuous operation of HVAC systems.

The Effects of Fatigue Cracks on Fastener Loads during Cyclic Loading and on the Stresses Used for Crack Growth Analysis in Classical Linear Elastic Fracture Mechanics Approaches

High strength threaded fasteners are widely used in the aircraft industry, and service experience shows that for structures where shear loading of the joints is significant, like skin splices, fuselage joints or spar caps-web attachments, more cracks are initiated and grow from the edges of the fastener holes than from features like fillets radii and corners or from large access holes. The main causes of this cracking are the stress concentrations introduced by the fastener holes and by the threaded fasteners themselves, with the most common damage site being at the edge of the fastener holes. Intuitively, it is easy to visualize that after the crack initiation, during the growth stages, some of the load transferred initially by the fastener at the cracked hole will decrease, and it will be shed to the adjacent fasteners that will carry higher loads than in uncracked condition. Using currently available computer software, the method presented in this paper provides a relatively quick and quantitatively defined solution to account for the effects of crack length on the fastener loads transfer, and on the far field and bypass loads at each fastener adjacent to the crack. At each location, these variations are determined from the 3-dimensional distribution of stresses in the joint, and accounting for secondary bending effects and fastener tilt. Two cases of a typical skins lap splice with eight fasteners in a two rows configuration loaded in tension are presented and discussed, one representative for wing or fuselage skins configurations, and the second case representative for cost effective laboratory testing. Each case presents five cracking scenarios, with the cracks growing from approx. 0.03 inch to either the free edge, next hole or both simultaneously.

切顶沿空留巷充填体—矸石协同承载机理及控制技术研究

针对深部沿空留巷顶底板移近量大、充填体大变形破坏失稳等问题,采用数值模拟和现场实践相结合的方法,分析了传统沿空留巷和切顶卸压协同承载沿空留巷围岩应力演化规律和变形特征,揭示了切顶沿空留巷充填体—矸石协同承载机理。在此基础上,以朱庄煤矿Ⅲ635工作面沿空留巷为工程背景,提出了一种巷旁充填体—矸石组合结构体协同承载的切顶卸压沿空留巷技术,建立充填体—矸石协同支撑顶板力学模型、推导出顶板挠度方程,并进行工程应用。数值模拟结果表明:采用切顶卸压协同承载沿空留巷技术后,实体煤帮和充填体的垂直应力峰值分别降低了28.3%、44.4%,巷道顶底板移近量降低了58.2%。现场应用结果表明:采用该技术后,顶底板和两帮移近量分别为382.9、253.6 mm,工作面支架平均支撑力下降了45.3%,有效控制了巷道变形。可为类似条件下沿空留巷围岩控制提供参考。

高速铁路无砟轨道车辆荷载传递特性研究

为进一步探讨无砟轨道荷载设计参数取值,为我国时速400 km及以上高速铁路建设提供重要理论支撑,通过开展无砟轨道静力分析以及钢轨焊缝、车轮扁疤激励下车辆-轨道动力相互作用,揭示列车静、动力载荷特征及传递规律;同时根据轨道承载特点和无砟轨道设计原理,提出车辆竖向设计荷载取值建议。研究结果表明:(1)高速列车车轮扁疤和钢轨焊缝不平顺将造成显著的轮轨冲击,其轮载动载系数最大可达5.79,远高于现行规范取值;扣件系统对扁疤和焊缝不平顺引起的轮轨力高频成分衰减作用明显,扣件支反力的动载系数最大为2.64;(2)钢轨焊缝不平顺引起的轮轨冲击力随着车速提高以及焊缝不平顺幅值的增大而迅速增大,建议500 km/h及以下高速铁路的钢轨焊缝平直度标准取0.2 mm/m;(3)列车轮载通过扣件支反力作用于轨道板,从传递特性的角度来说,以扣件支反力作为轨道板竖向设计荷载更为合理,其动载系数可取3.0,且能满足400 km/h及以上高速铁路的行车需求。

常泰长江大桥组合索塔锚固结构钢-混传剪构造足尺模型试验研究

常泰长江大桥索塔锚固结构采用钢箱-核芯混凝土组合结构,为研究该新型组合索塔锚固结构钢-混传剪构造的受力特性,进行钢-混传剪构造足尺模型试验研究。制作2个锚固结构足尺节段试验模型,通过压剪试验研究锚固结构的荷载~滑移曲线及应力、应变分布等受力特性,并通过有限元模型分析锚固结构的传力机理和各组件的内力分配比例,推导剪力钉剪力计算方法。结果表明:在2.14倍单索最大索力荷载作用下,锚固结构保持弹性状态,钢壁板未产生明显滑移,钢-混界面最大滑移不超过0.25 mm,该锚固结构中钢-混传剪构造至少具有2.14倍的安全系数;荷载作用下,剪力钉剪力从上至下逐渐增大,锚腹板附近底部3排剪力钉剪力较大,钢-混传剪构造至少存在剪力钉和界面摩擦力2种传剪机制,钢-混传剪构造的承载能力显著提高;钢-混传剪构造受力过程分为粘结力传力阶段和局部滑移阶段,剪力钉剪力分布不仅与沿剪切方向长度分布有关,也与荷载的大小线性相关。