OBSERVATION OF THE EFFECT OF S－（－）USNIC ACID SODIUM ON TRICHOMONAS VAGINALIS BY TRANSMISSION ELECTRON MICROSCOPE

This paper reports the ultrastructural changes of trichomonas vaginaiis (T. vag. ) under the action of s-(-)usnic acid sodium in vitro. These changes can be shown by the following results:At first, the degranulation of the rough endoplasmic reticulum (RER) took place, the polyribosomes disaggregated. And then, the Golgi complex and the endoplasmic reticulum dilated. The cytoplasmic matrix presented and inhomogeneous apperance. Finally, the biomembrane loosed and fractured.The cell nuclei presented the karyorrhexis.

Characterization of Li-rich layered oxides by using transmission electron microscope

Lithium-rich layered oxides(LrLOs) deliver extremely high specific capacities and are considered to be promising candidates for electric vehicle and smart grid applications. However, the application of LrLOs needs further understanding of the structural complexity and dynamic evolution of monoclinic and rhombohedral phases, in order to overcome the issues including voltage decay, poor rate capability, initial irreversible capacity loss and etc. The development of aberration correction for the transmission electron microscope and concurrent progress in electron spectroscopy, have fueled rapid progress in the understanding of the mechanism of such issues. New techniques based on the transmission electron microscope are first surveyed, and the applications of these techniques for the study of the structure, migration of transition metal, and the activation of oxygen of LrLOs are then explored in detail, with a particular focus on the mechanism of voltage decay.

Ultrastructural view of colon anastomosis under propolis effect by transmission electron microscopy

AIM： To evaluate the effect of propolis administration on the healing of colon anastomosis with light and transmission electron microscopes. METHODS： Forty-eight Wistar-AIbino female rats were divided into two groups and had colon resection and anastomosis. In group Ⅰ, rats were fed with standard rat chow pre- and postoperatively. The rats in group Ⅱ were fed with standard rat chow and began receiving oral supplementation of propolis 100 mg/kg per day beginning 7 d before the operation and continued until they were sacrificed. Rats were sacrificed 1, 3, 7 and 14 d after operation, and anastomotic bursting pressures measured. After the resection of anastomotic segments, histopathological examination was performed with light and transmission electron microscopes by two blinded histologists and photographed. RESULTS： The colonic bursting pressures of the propolis group were statistically significantly better than the control group. UItrastructural histopathological analysis of the colon anastomosis revealed that propotis accelerated the phases of the healing process and stimulated mature granulation tissue formation and collagen synthesis of fibroblasts. CONCLUSION： Bursting pressure measurements and ultra structural histopathological evaluation showed that administration of propolis accelerated the healing of colon anastomosis following surgical excision.

Specimen preparation of aluminum alloy powders for transmission electron microscopy

By nickel electroplating at room temperature, the specimen preparation of ultra sonic gas atomized aluminum alloy powders for observation in transmission electron microscope was carried out. The advantages of this technique are simple technologically and convenient practically. The nickel and the powders combine well in the plated sheet which can be thinned by ion milling. The powders in the thinned sheet possess large thinned area and can be examined in common TEM for the studies of their microstructure.

Characterization of swift heavy ion tracks in MoS2 by transmission electron microscopy

The various morphologies of tracks in MoS2 irradiated by swift heavy ions at normal and 30° incidence with 9.5–25.0 MeV/u 86Kr, 129Xe, 181Ta, and 209Bi ions were investigated by transmission electron microscopy. The diameter of ion tracks increases from 1.9 nm to 4.5 nm with increasing electronic energy loss. The energy loss threshold of the track formation in MoS2 is predicted as about 9.7 keV/nm based on the thermal spike model and it seems consistent with the experimental results. It is shown that the morphology of ion tracks is related to the penetration length of ions in MoS2. The formation process of ion tracks is discussed based on the cooperative process of outflow and recrystallization of the molten phase during rapid quenching.

Bacteriophage Morphological Characterization by Using Transmission Electron Microscopy

Bacteriophages or more commonly ＂phages＂ are bacterial viruses. They are ubiquitous and good indicators of bacterial contaminations since their prevalence is high in those environments where their hosts are abundant. Phage classification is based on morphology and for this reason, even though it is considered an old technique, TEM （Transmission Electron Microscopy） still plays a key role in their characterization. In the present work, the authors focused on TEM analysis of phage ФApr-1 isolated against Lactococcuslactis （L. lactis）, implicated in industrial fermentations and of phage ФIZSAM-1, active against Listeria monocytogenes （L. monocytogenes）, isolated from the environment. For observation with TEM （EM 900T-Zeiss）, phages were harvested in liquid media and were negative stained with fosfotungstic acid 2‰. An accurate viral ultrastructure analysis by using TEM is fundamental not only in the first approach of characterization of newly isolated phages but also for providing useful information to go further to the selection process as potential bio-decontaminants.

Tracking lithiation with transmission electron microscopy

Li-ion batteries(LIBs)have dominated energy-storage techniques for portable electronic devices and electric cars,and are expanding their territory into the large-scale energy storage.The energy storage of LIBs is realized by the reversible shuttle of lithium ions between electrodes.It is essential to track the lithium diffusion and obtain a profound insight into the lithiation mechanism during the work cycle of LIBs.Transmission electron microscopy(TEM)is a powerful tool for the structural characterization,which can provide the information about the lithiation at the atomic scale.In this review,we summarize the research frontiers of TEM applications on LIBs.We introduce the techniques for the direct observation of Li species in LIB-related materials.Especially,the application of cryo-TEM is highlighted.Moreover,in-situ TEM technique is further discussed since it shows great advantages in studying the dynamical structure changes of LIBs.The perspectives and strategies in this review offer feasible guidance for researchers to further improve the performance of LIBs.

Bacteriological and electron microscopic examination of primary intrahepatic stones

BACKGROUND: Primary intrahepatic cholelithiasis is usually combined with biliary tract infection. This research was undertaken to investigate the relationship between intrahepatic stones and biliary tract infection. METHODS: Thirty-five bile samples and 30 stones specimens were cultured for bacteria and 12 stones specimens were examined with a scan electron microscope (SEM) or a transmission electron microscope (TEM). RESULT: 94.2% bile samples and 96.7% stones specimens were positive in bacteria culture. Bacteria were found in stones under SEM and TEM. CONCLUSION: Bacteria in stones are associated with the infection of the biliary tract.

Nanoelectronic devices resonant tunnelling diodes grown on InP substrates by molecular beam epitaxy with peak to valley current ratio of 17 at room temperature

This paper reports that InAs/In0.53Ga0.47As/AlAs resonant tunnelling diodes have been grown on InP substrates by molecular beam epitaxy. Peak to valley current ratio of these devices is 17 at 300K. A peak current density of 3kA/cm^2 has been obtained for diodes with AlAs barriers of ten monolayers, and an Ino.53Ga0.47As well of eight monolayers with four monolayers of InAs insert layer. The effects of growth interruption for smoothing potential barrier interfaces have been investigated by high resolution transmission electron microscope.

基于MEMS芯片的磁性材料TEM表征技术

传统透射电子显微镜(TEM)以电磁场为透镜,通常情况下磁性材料不能直接在TEM下进行观测,一般使用以碳为支撑膜的双联铜网作为样品载网,但仍然有一定的破损概率。设计并实现了一种新型的基于微电子机械系统(MEMS)芯片的磁性材料TEM表征技术。该技术通过磁性TEM芯片和配套的样品杆,在TEM内形成一个密闭空间。将磁性样品上载到磁性TEM芯片上,从而实现在TEM下对磁性样品的安全观测。该芯片的核心结构是可以透射电子束的超薄氮化硅窗口,该窗口采用低压化学气相沉积(LPCVD)法制备,具有极高的机械强度,最高可以承受接近400 kPa的气压差。实验结果表明,利用该TEM表征技术可以在TEM下成功观测铁包硅和NiO两种磁性材料,分辨率可以达到原子级。

FinFET芯片TEM样品制备及避免窗帘效应方法

制备高质量纳米尺度芯片透射电子显微镜(TEM)样品对于探索半导体器件结构设计、材料分布与芯片性能之间的关系具有重要的意义。使用聚焦离子束(FIB)/扫描电子显微镜(SEM)双束系统制备14 nm鳍式场效应晶体管(FinFET)截面TEM样品,制备过程中从技术角度提出了两种自下而上制样方案来抑制窗帘效应。为扩大样品的可表征视场范围,在避免样品弯曲的前提下,提出了一种薄片提取方法。结果表明,离子束流越大,窗帘效应越严重,自下而上方法能有效规避窗帘效应;离子束电压30 kV时采用清洗截面(CCS)模式、5 kV/2 kV时采用矩形模式,样品台倾斜补偿角度为1.5°~3.5°,进行交叉减薄,且最终铣削长度控制在1μm时减薄效果最好;新的薄片提取方法改变了样品的铣削方向,在避免窗帘效应破坏感兴趣结构和样品弯曲的前提下,将样品的可表征视场范围扩大了5倍。研究结果对优化TEM样品制备方法以及芯片失效分析提供了参考。

Mssbauer and electron microscopy study of martensitic transformations in an Fe-Mn-Mo alloy

The kinetic,morphological,crystallographic,and magnetic characteristics of thermally induced martensites in Fe-13.4wt% Mn-5.2wt%Mo alloy were investigated by scanning electron microscopy（SEM）,transmission electron microscopy（TEM）,and M（o｜¨）ssbauer spectroscopy.The experimental results reveal that two types of thermal-induced martensites,e（hcp） andα＇（bcc） martensites,are formed in the as-quenched condition,and these transformations have athermal characters.Mo addition to the Fe-Mn alloy does not change the coexistence ofεandα＇ martensites with the Mn content between 10wt%and 15wt%.Besides,M（o｜¨）ssbauer spectra reveal a paramagnetic character with a singlet for theγ（fcc） austenite andεmartensite phases and a ferromagnetic character with a broad sextet for theα＇ martensite phase. The volume fraction ofα＇ martensite forming in the quenched alloy is much more than that of theεmartensite.

Ultrafast electron microscopy in material science

Recent advances in the ultrafast transmission electron microscope （UTEM）, with combined spatial and temporal resolutions, have made it possible to directly visualize the atomic, electronic, and magnetic structural dynamics of materials. In this review, we highlight the recent progress of UTEM techniques and their applications to a variety of material systems. It is emphasized that numerous significant ultrafast dynamic issues in material science can be solved by the integration of the pump-probe approach with the well-developed conventional transmission electron microscopy （TEM） techniques. For instance, UTEM diffraction experiments can be performed to investigate photoinduced atomic-scale dynamics, including the chemical reactions, non-equilibrium phase transition/melting, and lattice phonon coupling. UTEM imaging methods are invaluable for studying, in real space, the elementary processes of structural and morphological changes, as well as magnetic-domain evolution in the Lorentz TEM mode, at a high magnification. UTEM electron energy-loss spectroscopic techniques allow the examination of the ultrafast valence states and electronic structure dynamics, while photoinduced near-field electron microscopy extends the capability of the UTEM to the regime of electromagnetic-field imaging with a high real space resolution.

聚焦离子束制样条件对TEM样品形貌的影响

聚焦离子束(FIB)因其制样成功率和效率高,可定点精确制样等特点已经成为半导体失效分析领域重要的透射电子显微镜(TEM)制样方法。利用双束FIB系统针对TEM样品制备条件对样品形貌的影响进行了分析和研究。通过控制变量法等方法分析了FIB的电子束或离子束等制样条件可能对样品带来的损伤。通过实验发现,FIB的离子束能量对TEM样品热损伤影响较小,电子束的电压和电流是引起样品损伤的主要因素。实验证明,在电子束辅助沉积保护层时适当降低电子束的电压和电流,可有效改善样品的微观形貌。

Electron Micrographic Representations of Mechanisms of Action of Murine Norovirus on ATCC TIB-71 Cells and Level of Gene Expression

Human noroviruses (HuNoV) are the number one cause of viral gastroenteritis worldwide resulting in a significant cause of morbidity and mortality in all age groups. However, despite the medical relevance of HuNoV, effective treatment against norovirus infection is yet to be developed. In this study, we investigated the anti-Noroviral activity of Hibiscus sabdariffa (HS) calyces and Zanthoxylum armatum (ZA) seeds using murine norovirus, a surrogate of human norovirus. The antiviral mechanisms of action were also examined using a gene expression studies and transmission electron microscopy. Our results showed that virus-infected cells were left potentially void of all the cell machineries whereas uninfected cells represent healthy normal and dividing cells. The infected treated cells with extracts showed restoration of the dense cytoplasm, cytoplasmic membrane, and the nucleus. These cells were also associated with the expression of ORF genes. This study demonstrates the antiviral properties of Hibiscus sabdariffa (HS) calyces and Zanthoxylum armatum (ZA) and thus indicates their potential as natural remedies to treat noroviruses.

Nanoparticles Production and Inclusion in <i>S. aureus</i>Incubated with Polyurethane: An Electron Microscopy Analysis

This study shows that submicron/nanoparticles found in bacterial cells (S. aureus) incubated with polyurethane (a material commonly used for prostheses in odontostomatology) are a consequence of biodestruction. The presence of polyurethane nanoparticles into bacterial vesicles suggests that the internalization process occurs through endocytosis. TEM and FIB/SEM are a suitable set of correlated instruments and techniques for this multi facet investigation: polyurethane particles influence the properties of S. aureus from the morpho-functional standpoint that may have undesirable effects on the human body. S. aureus and C. albicans are symbiotic microorganisms;it was observed that C. albicans has a similar interaction with polyurethane and an increment of the biodestruction capacity is expected by its mutual work with S. aureus.

基于FIB-SEM和TEM的催化裂化催化剂元素分布研究

为了研究催化裂化(FCC)催化剂的失活机理,利用聚集离子束扫描电镜(FIB-SEM)制作透射电镜样品;采用扫描电镜、透射电镜、X射线荧光光谱、X射线能谱等手段,对FCC催化剂单个颗粒及其FIB切片的元素分布进行表征。结果发现:与新鲜剂相比,催化裂化过程中FCC平衡剂上沉积了Fe,Ni,V,Ca,P等元素;随着杂质元素沉积量的增加,催化剂的骨架密度逐渐增大;随着骨架密度增大,催化剂Fe,Ni,Ca含量提高,而其硅铝比、P含量、比表面积降低;Fe,Ni,P元素主要分布在催化剂颗粒外表面,V元素在催化剂内部和外部分布比较均匀。

Manufacturing of SEM and TEM Samples for Oocyte

[ Objective] The research aimed to explore the manufacturing methods of scanning electron microscope （SEM） and transmission electron microscopy （TEM） for oocyte and provide technical support for related research. [ Method] Based on GV-and MII-stage oocytes, samples of SEM and TEM were prepared respectively, then ultrastructure changes were observed. [ Result] The results showed that the method needed few samples, keep intact cell morphology and can see clear ultrastructure. [Conclusion] The method is suitable for ultrastructural observation of oocyte.

洛伦兹电镜在本科教学中的应用

磁畴是磁性材料中的基础结构,它决定了材料的磁学性质。通过深入研究磁畴,我们可以深入理解磁性材料的特性,优化其性能,进而推动相关应用的进步。洛伦兹电镜,作为一种基于透射电镜的设备,能够观察和分析磁性材料的磁畴结构。其工作原理是利用洛伦兹力使电子束发生偏转,形成明暗相间的图案,从而反映出面内磁矩的不同取向。洛伦兹电镜具有超高的探测灵敏度,其分辨率能够达到纳米量级,因此被广泛应用于磁性材料的研究。将洛伦兹电镜引入本科教学是非常有意义的。通过实际操作,学生可以更好地掌握科学研究的实践技能和方法。同时,学生还能够培养科研素养和科研能力,为他们未来的科研工作打下坚实的基础。因此,将洛伦兹电镜应用于本科教学不仅是可行的,而且是必要的。

ZnO/ZnSe复合材料的制备、 表征及催化特性

对传统的两步水合热法进行改进,采用更加经济、安全、简便的方法在室温下合成ZnO/ZnSe核壳结构。调节原料比例,实验温度,优化了制备ZnO/ZnSe核壳结构的最佳生长与修饰条件,使其具有良好的分散性,时间稳定性,良好的发光特性。研究采用醋酸锌作为锌源,硒粉作为硒源,通过调整原料比例以及实验温度制备出球形核壳结构的ZnO/ZnSe复合材料,用透射电子显微镜(TEM),X射线粉末衍射仪(XRD),紫外可见分光光度计(UV-Vis),光致发光光谱(PL),X射线光电子能谱(XPS)对晶体结构进行了表征,同时对光催化性能进行了研究。结果表明,改变实验条件,原料比例为Zn∶Se=1.6∶1,温度为80℃时生成的ZnO/ZnSe核壳结构对甲基橙溶液有较好的吸光效果。ZnSe过厚的壳层生长会阻碍复合材料对甲基橙的降解效率。实验数据结合理论分析得到了实验最佳条件。