Numerical Flow Simulation in Turbine Mode of Counter-Rotating Type Pumping Unit to Cooperate with Wind Turbine

This serial research has proposed the hybrid power system combined the wind power unit with the counter-rotating type pump-turbine unit, to provide the constant output for the grid system, even at the suddenly fluctuating/turbulent wind circumstance. In this paper, the tandem impellers prepared for the counter-rotating type pumping unit were operated at the turbine mode, and the performances and the flow conditions were investigated numerically with accompanying the experimental results. Even though providing the pumping unit for the turbine mode, the maximum hydraulic efficiency is close to one of the counter-rotating type hydroelectric unit designed exclusively for the turbine mode. Besides, the runners/impellers of the unit work evidently so as to coincide the angular momentum change through the front runners/impellers with that through the rear runners/impellers, namely to take the axial flow at not only the inlet but also the outlet, without the guide vanes. From these results, it can be concluded that this type unit is effective to work at not only the pumping but also the turbine modes.

A Hydraulic Performance Comparison of Centrifugal Pump Operating in Pump and Turbine Modes

The modifications of impeller may show diverse impact on centrifugal pump operating in pump and turbine modes.To clarify this problem,the hydraulic performance of a low specific speed centrifugal pump operating in both modes was firstly obtained by CFD method and verified by experiment.Then,based on the single-factor design method,a series of calculations have been conducted to identify the effects of impeller geometry parameters on the hydraulic performance in different modes.The variations of head,shaft power and hydraulic efficiency curves with different impeller parameters were explored.It is found that compared with turbine,the pump shows a more obvious variation of head.The outlet angle has positive impact both on the head consumed by pump or generated by turbine.The change of turbine shaft power is apparently smaller than that of pump for different impeller geometry parameters.Only the outlet width somewhat changes the turbine shaft power.The hydraulic efficiency in both modes shows different variation under different impeller geometric parameters,while the hydraulic efficiency of both modes is reduced with the outlet angle increasing.Meanwhile,the response amount of hydraulic efficiency caused by certain change of impeller parameters was estimated by sensitivity analysis method.It is found that only the appropriate blade number and outlet width can improve the hydraulic performance both in pump and turbine modes.Eventually,the hydraulic loss,skin friction loss and theoretical analysis were performed to explore the reason of hydraulic performance variation due to different impeller parameters.The change of slip factor,impeller inlet area,impeller outlet area or hydraulic loss results in the change of hydraulic performance in both modes.The results can be useful for hydraulic performance improvement for both pump and turbine modes through impeller geometry modification.

PCTRAN Westinghouse AP1000 Power Control of Pressurized Water Reactor Using Simulink of MATLAB

This paper introduces the simulation, and controls using Simulink of MATLAB for PCTRAN (Personal Computer Transient Analysis) of the power control system (PWR) type pressurized water reactor of PWR WESTINGHOUSE AP1000. The power controller model produces mathematical model description in nonlinear relation form in Simulink of MATLAB which is an important and popular program used at most universities for education. The power controller is described by a block diagram in this paper and some details introduce to clearly understand the work function. The results of action control compared with the PCTRAN programme in modes of automatic and manual control.

Numerical simulation of hydraulic force on the impeller of reversible pump turbines in generating mode

The hydraulic force on the reversible pump turbine might cause serious problems（e.g., the abnormal stops due to large vibrations of the machine）, affecting the safe operations of the pumped energy storage power plants. In the present paper, the hydraulic force on the impeller of a model reversible pump turbine is quantitatively investigated through numerical simulations. It is found that both the amplitude of the force and its dominant components strongly depend on the operating conditions（e.g., the turbine mode, the runaway mode and the turbine brake mode） and the guide vane openings. For example, the axial force parallel with the shaft is prominent in the turbine mode while the force perpendicular to the shaft is the dominant near the runaway and the turbine brake modes. The physical origins of the hydraulic force are further revealed by the analysis of the fluid states inside the impeller.

Experimental investigations of a prototype reversible pump turbine in generating mode with water head variations

Influences of water head variations on the performances of a prototype reversible pump turbine are experimentally studied in generating mode within a wide range of load conditions(from 25% to 96% of the rated power). The pressure fluctuations of the reversible pump turbine at three different water heads(with non-dimensional values being 0.48, 0.71 and 0.90) are measured and compared based on the pressure data recorded in the whole flow passage of the turbine. Furthermore, effects of monitoring points and load variations on the impeller-induced unstable behavior(e.g. blade passing frequency and its harmonics) are quantitatively discussed. Our findings reveal that water head variations play a significant role on the pressure fluctuations and their propagation mechanisms inside the reversible pump turbine.

Counter-Rotating Type Pump-Turbine Unit Cooperating with Wind Power Unit

This serial research proposes the hybrid power system combined the wind power unit with the counter-rotating type pump-turbine unit,to provide the constant output for the grid system,even at the suddenly fluctuating/turbulent wind.In this paper,the tandem impellers of the counter-rotating type pumping unit was operated at the turbine mode,and the performances and the flow conditions were investigated numerically and experimentally.The 3-D turbulent flows in the runners were simulated at the steady state condition by using the commercial CFD code of ANSYS-CFX ver.12 with the SST turbulence model.While providing the pump unit for the turbine mode,the maximum hydraulic efficiency is close to one of the counter-rotating type hydroelectric unit designed exclu-sively for the turbine mode.Besides,the runner/impeller of the unit works evidently so as to coincide the angularmomentum change through the front runners/impellers with that through the rear runners/impellers,namely to take the axial flow at not only the inlet but also the outlet without the guide vanes.These results show that this type of unit is effective to work at not only the pumping but also the turbine modes.