ISOCHRONOUS STRESS-STRAIN CURVES OF LOW ALLOY STEEL CROSS-WELD-SPECIMEN AT HIGH TEMPERATURE

In this work, a parametric approach is presented and utilized to determine the creep properties of weldments; then the model of creep strain for cross weld specimen is given. On the basis of the experimental results, attempt has been made to establish equations of the isochronous stress-strain for weld joint that can predict the function of loading and service time in use of the creep data of base metal and weld metal.

Numerical simulation of the stress-strain curve and the stress and strain distributions of the titanium-duplex alloy

The stress-strain curve of an α-β Ti-8Mn alloy was measured and then it was calculated with finite element method （FEM） based on the stress-strain curves of the single α and β phase alloys. By comparing the calculated stress-strain curve with the measured one, it can be seen that they fit each other very well. Thus, the FE model built in this work is effective. According to the above mentioned model, the distributions of stress and strain in the α and β phases were simulated. The results show that the stress gradients exist in both α and β phases, and the distributions of stress are inhomogeneous. The stress inside the phase is generally higher than that near the interface. Meanwhile, the stress in the α phase is lower than that in the β phase, whereas the strain in the α phase is higher than that in the β phase.

The Complete Stress-strain Curve of Recycled Aggregate Concrete under Uniaxial Compression Loading

The mechanical performance of recycled aggregate concrete （RAC） is investigated. An experiment on the complete stress-strain curve under uniaxial compression loading of RAC is carried out. The experimental results indicate that the peak stress, peak strain, secant modulus of the peak point and original point increase with the strength grade of RAC enhanced. On the contrary, the residual stress of RAC decreases with the strength grade enhancing, and the failure of RAC is often broken at the interface between the recycled aggregate and the mortar matrix. Finally, the constitutive model of stress-strain model of RAC has been constituted, and the results from the constitutive model of stress-strain meet the experiment results very well.

Charactersitics of Stress-strain Curve of High Strength Steel Fiber Reinforced Concrete under Uniaxial Tension

A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.

On the calibration of a shear stress criterion for rock joints to represent the full stress-strain profile

Conventional numerical solutions developed to describe the geomechanical behavior of rock interfaces subjected to differential load emphasize peak and residual shear strengths.The detailed analysis of preand post-peak shear stress-displacement behavior is central to various time-dependent and dynamic rock mechanic problems such as rockbursts and structural instabilities in highly stressed conditions.The complete stress-displacement surface(CSDS)model was developed to describe analytically the pre-and post-peak behavior of rock interfaces under differential loads.Original formulations of the CSDS model required extensive curve-fitting iterations which limited its practical applicability and transparent integration into engineering tools.The present work proposes modifications to the CSDS model aimed at developing a comprehensive and modern calibration protocol to describe the complete shear stressdisplacement behavior of rock interfaces under differential loads.The proposed update to the CSDS model incorporates the concept of mobilized shear strength to enhance the post-peak formulations.Barton’s concepts of joint roughness coefficient(JRC)and joint compressive strength(JCS)are incorporated to facilitate empirical estimations for peak shear stress and normal closure relations.Triaxial/uniaxial compression test and direct shear test results are used to validate the updated model and exemplify the proposed calibration method.The results illustrate that the revised model successfully predicts the post-peak and complete axial stressestrain and shear stressedisplacement curves for rock joints.

High temperature stress–strain curves of MnS and their applications in finite element simulation

A novel method for testing stress–strain curves of non-metallic materials was presented.The high temperature stress-strain curves of MnS were preliminarily obtained and corrected to account for the influence of friction.Using the finite element method,the influence of deformation parameters on the deformation evolution of MnS inclusions was investigated based on the experimental reference data.The corresponding physical experiment was designed for comparative analysis.The results indicate that the experimental high-temperature deformation data of MnS are highly reliable.In the process of matrix deformation,the shapes of MnS inclusions change from spherical to ellipsoidal and even to lamellar.There are some differences in the morphological deformation of MnS inclusions located at different positions.With the increase in the initial size of MnS inclusions,the risk of failing the inclusion-flaw inspection increases and the forging quality further deteriorates.

Relations of complete creep processes and triaxial stress-strain curves of rock

Based on the results of triaxial compressive creep tests for five kinds of rock under the different stress loading,unloading and cycle-loading-unloading conditions,the creep deformation is not only a function of stress and time,but also it has the corresponding relations to the triaxial stress-strain curves of rock.The deformation properties of soften-strain,harden-strain and ideal plasticity presented by conventional triaxial compressive test curves under the different stress states were utilized,and the creep characteristics,the creep starting stress and the different entire creep process curves of rock were studied systematically according to creep experiment results,and the relations of the triaxial stress-strain curves to the creeping starting stress,the terminating curve,the different creep processes,and the different creep fracture properties were established.The relations presented in this paper were verified partially by the creep experiment results of five types of rock.

MODELLING OF TENSILE STRESS-STRAIN CURVE OF WOVEN FABRICS

A general shape of tensile stress-strain curves of woven fabrics is first recognised by puttingtested and predicted results together.An exponential function with two parameters is then selectedfor the prediction of tensile stress-strain relationship.The predicted results by using the proposedfunction show excellent agreement with experimental data.

Investigation into the stress-strain curves of deformation-induced ferrite transformation in a low carbon steel

A series of tests of deformation-induced ferrite transformation （DIP-T） in a low carbon steel were carried out by the Gleeble-3500 hot simulation machine at a temperature range of Ae3-Ar3. The overall stress-strain curves during DIFT can be divided into three typical types： ＂double-humped＂,＂ single-humped＂ and ＂transitional＂. The peaks exhibited in the curve are involved with deformation-induced transformation which happened in grains or at the grain boundaries. According to the stress-time curve and strain-time curve, strain capacity dramatically postponed the strain-induced transformation, which leads to the start of the transformation right ahead of the finish of deformation and the majority of the ferrite transformation process mainly happened after the deformation. Deformation-induced transformation is a metadynamic transformation process with dynamic nucleation.

Finite Element Modeling of Stress Strain Curve and Micro Stress and Micro Strain Distributions of Titanium Alloys— A Review

Most of the alloys like titanium, steel, brass, copper, etc., are used in engineering applications like automobile, aero- space, marine etc., consist of two or more phases. If a material consists of two or more phases or components it is very difficult to predict the properties like mechanical and other properties based on simple laws such as rule of mixtures. Titanium alloys are capable of producing different microstructures when it subjected to heat treatments, so much of money and time are squandering to study the effect of microstructure on mechanical properties of titanium alloys. This squandering can be reduced with the help of modeling and optimization techniques. There are many modeling tech- niques like Finite element method, Mat lab, Mathematical modeling etc. are available. But Finite element method is widely used for prediction because of capable of producing distributions of stresses and strains at any different loads. From the literature it is observed that there is a good agreement between the calculated and measured stress strain curves. This review paper describes the effect of volume fraction and grain size of alpha phase on the stress strain curve of the titanium alloys. It also can predict the effect of strength ratio on stress strain curve by using FEM. This informa- tion will be of great use in designing and selecting the titanium alloys for various engineering applications.

时间旅行的量子门

量子计算可以解决经典计算难于求解的问题,在物理原理允许范围内扩大了可有效计算的问题范围,对经典计算的扩展丘奇图灵论题提出了挑战.这里我们讨论一个有趣的问题:通过突破物理原理限制来实现更强大的计算机,进一步扩展量子计算机的能力.我们考虑一种全新的操纵能力,让量子计算可以实现时间穿梭旅行的量子控制门.这是量子门线路图形语言的一个符合直觉的扩展,作为例子,我们展示了一个可以有效求解SAT难题的扩展量子算法.我们的结果有助于更深刻地理解计算和物理原理之间的关系.

Plastic Flow Modeling of Ti-5 Al-2 Sn-2 Zr-4 Mo-4 Cr Alloy at Elevated Temperatures and High Strain Rates

The true stress-sWain relationships of Ti-5A1-2Sn-2Zr-4Mo-4Cr（TC17） alloy with a wide range of strain rates were investigated by tmiaxial quasi-static and dynamic compression tests, respectively. Quasi- static compression tests were carried out with Instron 8874 test machine, while dynamic compression tests were performed with the split Hopkinson pressure bar （SHPB） which was installed with heating device and synchro- assembly system. The dynamic mechanical behaviors tests of TC17 were carded out from room temperature to 800 ℃ at intervals of 200 ℃ and at high sWain rates （5 500-1 9200 s-l）. The stress-strain curves considering temperature-sWain rate coupling actions were obtained. The Johnson-Cook constitutive model was developed through data fitting of the stress-sWain curves. The material constants in the developed constitutive model can be determined using isothermal and adiabatic stress-strain curves at different strain rates. The Johnson-Cook constitutive model provided satisfied prediction of the plastic flow stress for TC17 alloy.

Stress-strain Model of Corroded Concrete under Uniaxial Compressive Loading

The prism specimens of corroded concrete were subjected to uniaxial compressive load to develop the stress-strain model. Compared to the un-corroded concrete, the mechanical prop- erties of corroded concrete, such as peak strength, Young＇s modulus, and residual deformation, et al are degraded. The concrete, which were subjected to the aggressive media in the environment, were resulted in randomly distributed pre-loading flaws and defects. The propagation of these corrosion flaws during the procedure of loading was the main reason of degradation of corroded concrete properties. By the application of the statistic theory of continuum damage, the compressive stress-strain curve of corroded concrete was simulated. The initial damage factor was introduced to represent the corrosive effects of different media. The present damage constitutive model agreed well with the test results.

Stress-strain analysis of loess triaxial shear test by PFC^(3D)

In order to compensate for limitations of microscopic study on loess triaxial tests, taking the loess in Longxi area as an example, the authors established the loess triaxial test model by using PFC3D software and simulating tfiaxial shear test under the different confining pressures in 0 kPa, 50 kPa and 300 kPa. Compared with laboratory triaxial shear test, the numerical simulation test has a guiding role in loess mechanical strength analysis.

Mechanical behaviour of wood compressed in radial direction-part I.New method of determining the yield stress of wood on the stress-strain curve

A test equipment was developed,which allows for real time observation of the deformation behav-ior of wood cellular structure under a compression load applied in radial direction.Compression tests were performed on jack pine(Pinus banksiana)and balsam poplar(Populus balsamifera)spec-imens to explore the relationship between the yield stress and the first failure occurring in wood cell layers during radial compression.The microstructural changes for P.banksiana and P.bal-samifera wood below and above the yield point were analyzed.The study results showed that for P.banksiana the first failure of wood cells occurred at the first earlywood layer,while for P.balsamifera it occurred at the layer with the largest vessels.The first failure of wood cell layer for each species tested was found to correspond to the yield point on the stress-strain curve.A new method of determining the yield stress for wood specimens under radial compression was developed.

Full-Range Compressive Stress-Strain Curves for Cold-Formed 304 Stainless Steel Circular Hollow Sections After Exposure to Vacuum Brazing

With the rapid development of microscale cellular structures, the small-diameter cold-formed welded stainless steel tubes have recently been used for creating the metallic lat- tice topologies with high mechanical properties. In this paper, to obtain the accurate material properties of the circular hollow section （CHS） under pure compression, a series of concentric compression tests are conducted on the millimeter-scale cold-formed 304 stainless steel circu- lar tubular stub columns after exposure to a vacuum brazing process. The tests cover a total of 18 small-diameter stub tubes with measured thickness-to-diameter ratios （t/D） from 0.023 to 0.201. A generalized three-stage nominal stress-strain model is developed for describing the compressive behavior of the post-brazing CHSs over the full strain range. This mechanical model is especially applicable to computer code implementation. Hence, an interactive computer pro- gram is developed to simultaneously optimize three strain hardening exponents （n1, n2, n3） in the expression of the model to produce the stress-strain curve capable of accurately replicating the test data. To further reduce the number of the model and material parameters on which this model depends, this paper also develops five expressions for determining the 2.5% proof stress （ap2）, n2, the ultimate compressive strength （σp3）, n3, and the ultimate plastic strain （p3%） for given experimental values of three basic material parameters （E0, σ0.01, σ0.2）. These expressions are validated to he effective for the CHSs with t/D 〉_ 0.027. The analytically predicted full-range stress-strain curves have generally shown close agreement with the ones obtained experimentally.

Fractal approximation of the stress-strain curve of frozen soil

A method to approach the stress-strain curve of frozen soil is presented based on the fact that the stressstrain curve of frozen soil has fractal property. First, a linear hyperbolic iterated function system (LHIFS) in which the perpendicular contraction factors are regarded as parameters is established using fractal geometry theories. Secondly, a method to calculate the best point which makes the attractor of the LHIFS an optimal approximation of the stress-strain curve of frozen soil is presented. Then, a method for calculating the fractal dimension of the stress-strain curve of frozen soil is obtained. Finally, a simple example is provided. The method presented in this paper provides a new method for simulating the stress-strain curve and calculating its fractal dimension of geomaterials that have the fractal feature by using computer.

Extracting compressive stress-strain curve based on stick-slip shear banding process in bulk metallic glasses

Based on the stick-slip process,an effective method to extract the stress-strain curve directly from the crosshead displacement-load raw data in compression of bulk metallic glasses was proposed.The method was tested in two bulk metallic glass samples with different plasticities and shear band morphologies.The extracted stress-strain curves were found to well resemble the stress-strain curve measured by a laser extensometer.In addition,the extracted curve could resolve fine structures of serrated flow much better than that measured by extensometer,thus facilitating the study of shear banding process.Results obtained by this method made the stick-slip dynamics of shear banding valid,and this method could be employed to obtain the real strain of small-sized metallic glass samples where extensometer cannot be applied.

Microscopic damage and dynamic mechanical properties of rock under freeze-thaw environment

For understanding the rock microscopic damage and dynamic mechanical properties subjected to recurrent freeze-thaw cycles, experiments for five groups of homogeneous sandstone under different freeze-thaw cycles were conducted. After freezethaw, nuclear magnetic resonance(NMR) tests and impact loading tests were carried out, from which microscopic damage characteristics of sandstone and dynamic mechanical parameters were obtained. The results indicate that the porosity increases with the increase of cycle number, the rate of porosity growth descends at the beginning of freeze-thaw, yet accelerates after a certain number of cycles. The proportion of pores with different sizes changes dynamically and the multi-scale distribution of pores tends to develop on pore structure with the continuing impact of freeze-thaw and thawing. Dynamic compressive stress-strain curve of sandstone undergoing freeze-thaw can be divided into four phases, and the phase of compaction is inconspicuous compared with the static curve. Elastic modulus and dynamic peak intensity of sandstone gradually decrease with freeze-thaw cycles, while peak strain increases. The higher the porosity is, the more serious the degradation of dynamic intensity is. The porosity is of a polynomial relationship with the dynamic peak intensity.

推导水驱特征曲线的渗流理论基础和通用方法

针对目前水驱特征曲线理论研究中的不足 ,提出了一种通用推导水驱特征曲线的理论方法。该方法主要从油、水两相渗流特征曲线出发 ,充分考虑到油田一般都有无水采收期 ,利用定积分导出了不同油、水两相渗流特征下带有校正项的完整形水驱特征曲线 ,从而揭示了渗流特征与水驱特征的内在联系 ,体现了油。