Now vibration isolation of ultra precision machine tool is usually achieved through air springs systems. As far as HCM I sub micro turning machine developed by HIT, an active vibration isolation system that consists o...Now vibration isolation of ultra precision machine tool is usually achieved through air springs systems. As far as HCM I sub micro turning machine developed by HIT, an active vibration isolation system that consists of air springs and electro magnetic actuators was presented. The primary function of air springs is to support the turning machine and to isolate the high frequency vibration. The electro magnetic actuators controlled by fuzzy neural networks isolate the low frequency vibration. The experiment indicates that active vibration isolation system isolates base vibration effectively in all the frequency range. So the vibration of the machine bed is controlled under 10 -6 g and the surface roughness is improved.展开更多
The characteristics of several different linear motors have been investigated, and the feed drive system with linear motor instead of screw-nut mechanism has been built for a submicro ultraprecision turning machine. I...The characteristics of several different linear motors have been investigated, and the feed drive system with linear motor instead of screw-nut mechanism has been built for a submicro ultraprecision turning machine. In the control system for the feed drive system arranged as "T", both P-position and PI-speed control loops are used. The feedback variable is obtained from a double frequecy laser interferometor. Experiments show that the feed drive with linear motor is simple in construction, and that its dynamics is better than others. So the machining accuracy of the workpiece machined has been successfully improved.展开更多
The investigation of low cost uncoated andcoated carbide insert in the hard turning of hardened AISID2 steel （≥55 HRC） will definitely open up a new arena asan economical alternative suitable to industrial machinin...The investigation of low cost uncoated andcoated carbide insert in the hard turning of hardened AISID2 steel （≥55 HRC） will definitely open up a new arena asan economical alternative suitable to industrial machiningsectors. Thus, this paper reports the comparative machin-ability assessment for the hard turning of AISI D2 steel（（55 ± 1） HRC） by coated and uncoated carbide insert in adry environment. Micro hardness and abrasion tests werecarried out to assess resistance capability against wear. Theabove test results confirmed the greater wear resistanceability of AIaO3 coated carbide insert over uncoated car-bide. Based on the extensive investigation of comparativemachinability, the coated carbide insert （TiN-TiCN-A12O3）outperformed the uncoated carbide insert with regard tosurface roughness, flank wear, chip-tool interface temper-ature, and chip morphology. Abrasion and diffusion wereobserved as the principal tool wear mechanisms in theinvestigated range. The uncoated carbide failed completelydue to the severe chipping and quick dulling of the cuttingedge, which led to its unsuitability for machining hardenedsteel.展开更多
文摘Now vibration isolation of ultra precision machine tool is usually achieved through air springs systems. As far as HCM I sub micro turning machine developed by HIT, an active vibration isolation system that consists of air springs and electro magnetic actuators was presented. The primary function of air springs is to support the turning machine and to isolate the high frequency vibration. The electro magnetic actuators controlled by fuzzy neural networks isolate the low frequency vibration. The experiment indicates that active vibration isolation system isolates base vibration effectively in all the frequency range. So the vibration of the machine bed is controlled under 10 -6 g and the surface roughness is improved.
文摘The characteristics of several different linear motors have been investigated, and the feed drive system with linear motor instead of screw-nut mechanism has been built for a submicro ultraprecision turning machine. In the control system for the feed drive system arranged as "T", both P-position and PI-speed control loops are used. The feedback variable is obtained from a double frequecy laser interferometor. Experiments show that the feed drive with linear motor is simple in construction, and that its dynamics is better than others. So the machining accuracy of the workpiece machined has been successfully improved.
文摘The investigation of low cost uncoated andcoated carbide insert in the hard turning of hardened AISID2 steel （≥55 HRC） will definitely open up a new arena asan economical alternative suitable to industrial machiningsectors. Thus, this paper reports the comparative machin-ability assessment for the hard turning of AISI D2 steel（（55 ± 1） HRC） by coated and uncoated carbide insert in adry environment. Micro hardness and abrasion tests werecarried out to assess resistance capability against wear. Theabove test results confirmed the greater wear resistanceability of AIaO3 coated carbide insert over uncoated car-bide. Based on the extensive investigation of comparativemachinability, the coated carbide insert （TiN-TiCN-A12O3）outperformed the uncoated carbide insert with regard tosurface roughness, flank wear, chip-tool interface temper-ature, and chip morphology. Abrasion and diffusion wereobserved as the principal tool wear mechanisms in theinvestigated range. The uncoated carbide failed completelydue to the severe chipping and quick dulling of the cuttingedge, which led to its unsuitability for machining hardenedsteel.
