Dendritic spine degeneration:a primary mechanism in the aging process

Recent reports suggest that aging is not solely a physiological process in living beings;instead, it should be considered a pathological process or disease(Amorim et al., 2022). Consequently, this process involves a wide range of factors, spanning from genetic to environmental factors, and even includes the gut microbiome(GM)(Mayer et al., 2022). All these processes coincide at some point in the inflammatory process, oxidative stress, and apoptosis, at different degrees in various organs and systems that constitute a living organism(Mayer et al., 2022;AguilarHernández et al., 2023).

Comparative study of two biological nitrogen removal processes:A/O process and step-feeding process

Two biological nitrogen removal processes are compared in the aspect of nitrogen removal, process operation and energy saving. Results show that when the returned sludge ratio is 50% of the inflow rate, the step-feeding process achieves over 80% total nitrogen （TN） removal efficiency, but the TN removal efficiency of the A/O process is only 40%. Moreover, filamentous sludge bulking can be well restrained in the step-feeding process. Given the conditions of a returned sludge ratio of 100% and a nitrifying liquor recycle ratio of 200%, the TN removal efficiency is 78.32% in the A/O process, but the sludge volume index （SVI） value increases to 143 mL/g. In the step-feeding process, the SVI is only 94.4 mL/g when the TN removal efficiency reaches 81. 1%. The step-feeding process has distinct advantages over the A/O process in the aspects of practicability, nitrogen removal and operating stability.

Simultaneous nitrification and denitrification in step feeding biological nitrogen removal process

The simultaneous nitrification and denitrification in step-feeding biological nitrogen removal process were investigated under different influent substrate concentrations and aeration flow rates. Biological occurrence of simultaneous nitrification and denitrification was verified in the aspect of nitrogen mass balance and alkalinity. The experimental results also showed that there was a distinct linear relationship between simultaneous nitrification and denitrification and DO concentration under the conditions of low and high aeration flow rate. In each experimental run the floc sizes of activated sludge were also measured and the results showed that simultaneous nitrification and denitrification could occur with very small size of floc.

基于Arduino与Processing的心率检测计设计研究

随着社会经济的高速发展,人们的物质生活也有了极大的提高,但同时也伴随着各种疾病的到来,身体健康已经成为人们普遍关注的焦点,因此,心率检测仪、血压计、血糖仪等各种家用医疗监测仪器已经逐渐融入日常生活。心脏病是人们难以预防的突发致命疾病之一,本文介绍的是一款基于Arduino【是基于易用硬件和软件的原型开源平台,包由可编程的电路板(简称微控制器),以及集成开发环境(称为Arduino IDE)的现成软件组成】Processing(开源编程语言,包括编辑器、编译器、展示器)的简易心率检测计系统,其功能实用、操作简单,可以测量心率,当超出正常心率范围时及时预警,是一款便携的实时心率测试仪。

A two-step transient liquid phase diffusion bonding process of T91 steels

In this study, a two-step heating process is introduced for transient liquid phase （ TLP） diffusion bonding fo r sound joints with T91 heat resistant steels. At first, a short-time higher temperature heating step is addressed to melt the interlayer, followed by the second step to complete isothermal solidification at a low temperature. The most critical feature of our new method is producing a non-planar interface at the T9／ heat resistant steels joint. We propose a transitional liquid phase bonding of T91 heat resistant steels by this approach. Since joint microstructures have been studied, we tested the tensile strength to assess joint mechanical property. The result indicates that the solidified bond may contain a primary solid-solution, similar composition to the parent metal and free from precipitates. Joint tensile strength of the joint is not lower than parent materials. Joint bend＇s strengths are enhanced due to the higher metal-to-metal junction producing a non-planar bond lines. Nevertheless, the traditional transient liquid phase diffusion bonding produces planar ones. Bonding parameters of new process are 1 260 °C for 0. 5 min and 1 230 °C fo r 4 min.

Effect of Cu content on microstructures and mechanical properties of ADI treated by twostep austempering process

The effect of Cu content on the microstructures and mechanical properties (yield strength, ultimate tensile strength, impact energy, fracture toughness) of austempering ductile iron (ADI) treated by two-step austempering process were investigated. High Cu content in nodular cast irons leads to a significant volume fraction of retained austenite in the iron after austempering treatment, but the carbon content of austenite decreases with the increasing of Cu content. Moreover, austenitic stability reaches its maximum when the Cu content is 1.4% and then drops rapidly with further increase of Cu. The ultimate tensile strength and yield strength of the ADI firstly increases and then decreases with increasing the Cu content. The elongation keeps constant at 6.5% as the Cu content increases from 0.2% to 1.4%, and then increases rapidly to 10.0% with further increase Cu content to 2.0%. Impact toughness is enhanced with Cu increasing at first, and reaches a maximum 122.9 J at 1.4% Cu, then decreases with the further increase of Cu. The fracture toughness of ADI shows a constant increase with the increase of Cu content. The influencing mechanism of Cu on austempered ductile iron (ADI) can be classified into two aspects. On the one hand, Cu dissolves into the matrix and functions as solid solution strengthening. On the other hand, Cu reduces solubility of C in austenite and contributes more stable retained austenite.

Theoretical evaluation on nitrogen removal of step-feed anoxic/oxic activated sludge process

Evaluation on nitrogen removal of step-feed anoxic/oxic activated sludge process at the standpoint of reaction kinetics and process kinetics was conducted. Theoretical biological nitrogen removal efficiency was deduced based on the mass balance of nitrate in the last stage. The comparison of pre-denitrification process and step feed process in the aspects of nitrogen removal efficiency, volume of reactor and building investment was studied, and the results indicated that step-feed anoxic/oxic activated sludge process was superior to pre-denitrification process in these aspects.

Automatic control strategy for step feed anoxic/aerobic biological nitrogen removal process

Control of sludge age and mixed liquid suspended solids concentration in the activated sludge process is critical for ensuring effective wastewater treatment. A nonlinear dynamic model for a step-feed activated sludge process was developed in this study. The system is based on the control of the sludge age and mixed liquor suspended solids in the aerator of last stage by adjusting the sludge recycle and wastage flow rates respectively. The simulation results showed that the sludge age remained nearly constant at a value of 16 d in the variation of the influent characteristics. The mixed liquor suspended solids in the aerator of last stage were also maintained to a desired value of 2500 g/m3 by adjusting wastage flow rates.

A Novel 2-D Signal Processing Scheme for Quasi-Random Step Frequency Signal

Due to the heavy congestion in HF bands, HF radars are restricted to operating within narrow frequency bands. To improve the system bandwidth and avoid heavy interference bands, a quasi-random step frequency signal with discontinuous bands is presented. A novel two-dimensional signal processing scheme for this signal is proposed on the basis of delicate signal analysis. Simulation results demonstrate that the scheme could successfully realize the resolutions by decoupling the range-Doppler ambiguity, and effectively suppress the maximal sidelobe. Moreover, the scheme is simple and has good numerical stability.

3D Rigid-Plastic Finite Element Analysis for Skew Rolling Process of the Stepped Part

Based on rigid-plastic finite element method, a skew rolling process of stepped part is simulated. Considering nodesaving and effective remeshing, the tetrahedron solid elements are used to discrete workpiece. The workpiece material adopts rigid-plastic model, where the flow stress is function of effective strain, effective strain rate and temperature.The thermomechanical coupling is considered in the simulation. To model the spinning workpiece undergoing plastic deformation, a novel solution is presented and applied in this paper. The stress state in the workpiece and forming characteristic of skew rolling are analyzed. The forming load, including roller torque and forces in three directions are predicted. The above analyses are helpful to understanding of forming mechanisms and improving of process and die design.

Modeling and Simulation of Production Process on Dimethyl Ether Synthesized from Coal-based Syngas by One-step Method

As a result of shortage supply of oil resources, the process for the alternative coal-based fuel, dimethyl ether （DME）, has emerged as an important process in chemical engineering field. With the laboratory experiment data about DME synthesis and separation, the production process for DME with high purity is proposed when one-step synthesis of DME in slurry bed reactor from syngas is adopted. On the basis of experimental research and process analysis, the proper unit modules and thermophysical calculation methods for the simulation process are selected. Incorporated the experimentally determined parameters of reaction dynamic model for DME synthesis, regression constants of parameters in non-random two-liquid equation （NRTL） model for binary component in DME separation system with built-in properties model, .the process flowsheet, is.developed and simulated on the Aspen Plus platform. The simulation results coincide well with data obtained in laboratory experiment. Accordingly, the accurate simulation results offer useful references to similar equipment design and process operation optimization.

A rapid one-step electrodeposition process for fabrication of superhydrobic surfaces on anode and cathode

This work presents a method to solve the weak solubility of zinc chloride(ZnCl_2) in the ethanol by adding some reasonable water into an ethanol electrolyte containing ZnCl_2 and myristic acid(CH_3(CH_2)_(12)COOH).A rapid one-step electrodeposition process was developed to fabricate anodic(2.5 min) and cathodic(40 s) superhydrophobic surfaces of copper substrate(contact angle more than 150°) in an aqueous ethanol electrolyte.Morphology,composition,chemical structure and superhydrophobicity of these superhydrophobic surfaces were investigated by SEM,FTIR,XRD,and contact angle measurement,respectively.The results indicate that water ratio of the electrolyte can reduce the required deposition time,superhydrophobic surface needs over 30 min with anhydrous electrolyte,while it needs only 2.5 min with electrolyte including 10 mL water,and the maximum contact angle of anodic surface is 166° and that of the cathodic surface is 168°.Two copper electrode surfaces have different reactions in the process of electrodeposition time,and the anodic copper surface covers copper myristate(Cu[CH_3(CH_2)_(12)COO]_2) and cupric chloride(CuCl);while,zinc myristate(Zn[CH_3(CH_2)_(12)COO]_2) and pure zinc(Zn) appear on the cathodic surface.

First Step in Dissociation Process in the Gas Phase for Small Molecules with Neutral Atoms: Application with the Even-Odd Rule and a Specific Periodic Table for Organic and Inorganic Atoms

Dissociations in the gas phase of small molecules have been intensively studied and dissociation energies of various gases are available in reference works. Configurations of compounds before and after the dissociation are usually known, but local charges are not defined. Building on the even-odd rule, the topic of a series of previous articles by the same author, the objective of this paper is to show how it can be used to give electronic rules for dissociations in gases. To this end, a specific periodic table is created and used. The rules are applied to a selection of more than 30 common molecules, showing that the even-odd rule and its consequences are useful in explaining the phenomenon of dissociation in gases.

Developing super-hydrophobic and corrosion-resistant coating on magnesium-lithium alloy via one-step hydrothermal processing

Formation of super-hydrophobic and corrosion-resistant coatings can provide significant corrosion protection to magnesium alloys.However,it remains a grand challenge to produce such coatings for magnesium-lithium alloys due to their high chemical reactivity.Herein,a one-step hydrothermal processing was developed using a stearic-acid-based precursor medium,which enables the hydrothermal conversion and the formation of low surface energy materials concurrently to produce the super-hydrophobic and corrosion-resistant coating.The multiscale microstructures with nanoscale stacks and microscale spheres on the surface,as well as the through-thickness stearates,lead to the super-hydrophobicity and excellent corrosion resistance of the obtained coating.

IS HYPOMETHYLATION OF CELLULAR DNA A STEP REQUIRED IN THE INITIATION PROCESS OF CHEMICAL CARCINOGENESIS

The level of DNA methylation in carcinogen treat-ed cells were determined by HpaII restriction frag-ment length analysis of the newly replicated DNAslabelled with H-TdR 24 hr prior to harvesting aswell as by direct HPLC measurement of the 5-methyl-cytosine(~mC)contents of the cellular DNAs.

A Two-step Design Method for Shaft Work Targeting on Low-temperature Process

In low-temperature processes, there are interactions between heat exchanger network(HEN) and refrigeration system. The modification on HEN of the chilling train for increasing energy recovery does not always coordinate with the minimum shaft work consumption of the corresponding refrigeration system. In this paper, a systematic approach for optimizing low-temperature system is presented through mathematical method and exergy analysis. The possibility of "pockets", which appears as right nose section in the grand composite curve(EGCC) of the process, is first optimized. The EGCC with the pockets cutting down is designed as a separate part. A case study is used to illustrate the application of the approach for a HEN of a chilling train with propylene and ethylene refrigerant system in an ethylene production process.

Effects of extra-cellular polymeric substances on organic pollutants biodegradation kinetics for A-step of adsorption-biodegradation process

The features of organic pollutants degradation mainly characterized by bio-flocculation for step-A of adsorption-biodegredation（AB） process were studied. By investigating the relationship of extracellular polymeric substances（EPS） with bioflocculation and introducing kinetic model of organic pollutant degradation into EPS, the kinetic model of organic pollutant degradation for step-A hioflocculation was deducted. And through the experiments, the kinetic constants were calculated as follows： k1 =0. 005 3; kc1 =1 710.7 and vmax1=10 min^-1.

Optimization of Biodiesel Production from Waste Vegetable Oil Assisted by Co-Solvent and Microwave Using a Two-Step Process

The two-step catalyzing process for biodiesel production from waste vegetable oil was assisted by both co-solvent and microwave irradiation. Central composite design (CCD) was employed to optimize the reaction conditions. Optimal reaction conditions of the first step were alcohol to oil molar ratio of 9:1, catalyst (H2SO4) amount 1 wt%, reaction temperature 333 K, and reaction time 7.5 minutes;while for the second step, optimal reaction conditions were alcohol to oil molar ratio 12:1, catalyst (NaOH) amount 1 wt%, reaction temperature 333 K, and reaction time 2.0 minutes. The total reaction time was 9.5 min and the conversion rate of fatty acid methyl esters (FAMEs) achieved was 97.4%. The total reaction time was shorter than previous studies. Therefore, the co-solvent and microwave assisted two-step catalyzing process has a potential application in producing biodiesel from waste vegetable oil.

A novel integrated step-feed biofilm process for the treatment of decentralized domestic wastewater in rural areas of China

For wastewater treatment in rural areas, a novel three-stage step-feed wastewater treatment system, combined with a drop-aeration biofilm process, was tested in the laboratory to investigate its performance in removing suspended solids （SS）, chemical oxygen demand （COD）, NH4＋-N, total nitrogen （TN）, and total phosphorus （TP）. The removal rates of SS, COD and NH4＋-N were 90%, 80%, and 90% in efluent concentrations less than 10 mg/L, 50 mg/L and 8 mg/L, respectively. The TP removal rate was less satisfactory. The C/N ratio in the raw wastewater was often less than 3.5, and the removal efficiency of TN was therefore limited. A carbon-release batch experiment was carried out to measure the feasibility of enhancing denitrification at low influent C/N ratios. The result showed that the C/N could be over 9.0 in the supernatant. Polymerase chain reaction denaturing gradient gel electrophoresis technology was used to reveal the changes in the bacterial community during different stages of the integrated step-feed biofilm process. The results showed that banding patterns and the distribution of dominant bands for the same experimental period in different aerobic zones were similar. Phylogenetic analysis indicated that lanes 10, 11 and 12, which presented three aerobic zones at the same operation period, had the closest phylogenetic relationship among the lanes.

Influence of a multi-step process on the thickness reduction error of sheet metal in a flexible rolling process

Flexible rolling is a forming process based on thickness reduction, and the precision of thickness reduction is the key factor affecting bending deformation. The major purpose of the present work is to solve the problem of bending deformation error caused by insufficient thickness reduction. Under the condition of different rolling reductions with the same sheet thickness and the same thickness reduction with different sheet thicknesses, the thickness reduction error of sheet metal is analyzed. In addition, the bending deformation of sheet metal under the same conditions is discussed and the influence of the multi-step forming process on the thickness reduction error is studied. The results show that, under the condition of the same sheet thickness, the thickness reduction error increases with increasing rolling reduction because of an increase in work hardening. As rolling reduction increases, the longitudinal bending deformation decreases because of the decrease of the maximum thickness difference. Under the condition with the same thickness reduction, the thickness reduction error increases because of the decrease of the rolling force with increasing sheet thickness. As the sheet thickness increases, the longitudinal bending deformation increases because of the increase in the maximum thickness difference. A larger bending deformation is divided into a number of small bending deformations in a multi-step forming process, avoiding a sharp increase in the degree of work hardening; the thickness reduction error is effectively reduced in the multi-step forming process. Numerical simulation results agree with the results of the forming experiments.