Characteristics of high-sulfate wastewater treatment by two-phase anaerobic digestion process with Jet-loop anaerobic fluidized bed

A new anaerobic reactor, Jet-loop anaerobic fluidized bed （JLAFB）, was designed for treating high-sulfate wastewater. The treatment characteristics, including the effect of influent COD/SO42 ratio and alkalinity and sulfide inhibition in reactors, were discussed for a JLAFB and a general anaerobic fiuidized bed （AFB） reactor used as sulfate-reducing phase and methane-producing phase, respectively, in two-phase anaerobic digestion process. The formation of granules in the two reactors was also examined. The results indicated that COD and sulfate removal had different demand of influent COD/SO4^2- ratios. When total COD removal was up to 85%, the ratio was only required up to 1.2, whereas, total sulfate removal up to 95% required it exceeding 3.0. The alkalinity in the two reactors increased linearly with the growth of influent alkalinity. Moreover, the change of influent alkalinity had no significant effect on pH and volatile fatty acids （VFA） in the two reactors. Influent alkalinity kept at 400-500 mg/L could meet the requirement of the treating process. The JLAFB reactor had great advantage in avoiding sulfide and free-H2S accumulation and toxicity inhibition on microorganisms. When sulfate loading rate was up to 8. 1 kg/（m^3.d）, the sulfide and free-H2S concentrations in JLAFB reactor were 58.6 and 49.7 mg/L, respectively. Furthermore, the granules, with offwhite color, ellipse shape and diameters of 1.0-3.0 mm, could be developed in JLAFB reactor. In granules, different groups of bacteria were distributed in different layers, and some inorganic metal compounds such as Fe, Ca, Mg etc. were found.

Digital image processing of saturation for two-phase flow in planar porous media model

In this paper, the accuracy of estimating stained non-wetting phase saturation using digital image processing is examined, and a novel post-processing approach for calculating threshold is presented. In order to remove the effect of the background noise of images and to enhance the high-frequency component of the original image, image smoothing and image sharpening methods are introduced. Depending on the correct threshold, the image binarization processing is particularly useful for estimating stained non-wetting phase saturation. Calculated saturation data are compared with the measured saturation data during the two-phase flow experiment in an artificial steel planar porous media model. The results show that the calculated saturation data agree with the measured ones. With the help of an artificial steel planar porous media model, digital image processing is an accurate and simple method for obtaining the stained non-wetting phase saturation.

Treatment of methanol wastewater with two-stage and two-phase anaerobic process

The two-stage and two-phase anaerobic process (TSTP) composed of hydrolytic acidification reactor,first-order and second-order external circulation anaerobic reactors (EC) was taken to treat methanol wastewater. Test results show that TSTP process is quick start-up in 51 d, and the maximum VFA of hydrolytic acidification reactor effluent reaches 876 mg/L. Under the condition of volume loading of 6.56 kgCOD/m3·d, COD removal rate of the first-order EC reactor is about 85%, and under the condition of volume loading of 1.02 kgCOD/m3·d, COD removal rate of the second-order EC reactor is about 50%. When the inflow COD of TSTP process is between 7000-11000 mg/L, its effluent COD is lower than 600 mg/L. In the biological conversion process of methanol into methane,the production of acetic acids as an intermediate product can be ignored and the direct production of methane from methanol is predominant.

New numerical algorithm of gas-liquid two-phase flow considering characteristics of liquid metal during mold filling

A new program is developed for gas-liquid two-phase mold filling simulation in casting. The gas fluid, the superheated liquid metal and the liquid metal containing solid grains are assumed to be governed by Navier-Stokes equations and solved through Projection method. The Level set method is used to track the gas-liquid interface boundary. In order to demonstrate the correctness of this new program for simulation of gas-liquid two-phase mold filling in casting, a benchmark filling experiment is simulated （this benchmark test is designed by XU and the filling process is recorded by a 16-mm film camera）. The simulated results agree very well with the experimental results, showing that this new program can be used to properly predicate the gas-liquid two-phase mold filling simulation in casting.

Direct Patterning of Carbon Nanotube via Stamp Contact Printing Process for Stretchable and Sensitive Sensing Devices

Flexible and wearable sensing devices have broad application prospects in bio-monitoring such as pulse measurement,motion detection and voice recognition.In recent years,many significant improvements had been made to enhance the sensor’s performance including sensitivity,flexibility and repeatability.However,it is still extremely complicated and difficult to prepare a patterned sensor directly on a flexible substrate.Herein,inspired by typography,a lowcost,environmentally friendly stamping method for the mass production of transparent conductive carbon nanotube(CNT)film is proposed.In this dry transfer strategy,a porous CNT block was used as both the seal and the ink;and Ecoflex film was served as an object substrate.Welldesigned CNT patterns can be easily fabricated on the polymer substrate by engraving the target pattern on the CNT seal before the stamping process.Moreover,the CNT film can be directly used to fabricate ultrathin(300μm)strain sensor.This strain sensor possesses high sensitivity with a gauge factor(GF)up to 9960 at 85%strain,high stretchability(>200%)and repeatability(>5000 cycles).It has been used to measure pulse signals and detect joint motion,suggesting promising application prospects in flexible and wearable electronic devices.

Identification Method of Gas-Liquid Two-phase Flow Regime Based on Image Multi-feature Fusion and Support Vector Machine

The knowledge of flow regime is very important for quantifying the pressure drop, the stability and safety of two-phase flow systems. Based on image multi-feature fusion and support vector machine, a new method to identify flow regime in two-phase flow was presented. Firstly, gas-liquid two-phase flow images including bub- bly flow, plug flow, slug flow, stratified flow, wavy flow, annular flow and mist flow were captured by digital high speed video systems in the horizontal tube. The image moment invariants and gray level co-occurrence matrix texture features were extracted using image processing techniques. To improve the performance of a multiple classifier system, the rough sets theory was used for reducing the inessential factors. Furthermore, the support vector machine was trained by using these eigenvectors to reduce the dimension as flow regime samples, and the flow regime intelligent identification was realized. The test results showed that image features which were reduced with the rough sets theory could excellently reflect the difference between seven typical flow regimes, and successful training the support vector machine could quickly and accurately identify seven typical flow regimes of gas-liquid two-phase flow in the horizontal tube. Image multi-feature fusion method provided a new way to identify the gas-liquid two-phase flow, and achieved higher identification ability than that of single characteristic. The overall identification accuracy was 100%, and an estimate of the image processing time was 8 ms for online flow regime identification.

Three-Dimensional Rigid-Plastic FEM Simulation of Bulk Forming Processes with New Contact and Remeshing Techniques

Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.

A Study on Law of Change of Real Contact Area of Friction during Transition Process

Mechanism of frictional vibration and the difference of kinctic-static friction is an open question. Research shows that the change of real area of contact during transition process of friction results in the phenomena mentioned above. In substance, the F-Vr, descent and F-T ascent characters are caused by A-Vr, and A-T characters respectively. Based on ultrasonic experiment the mechanism of the phenomena is explained and the frictional formulas using the parameter-real area of contact are given in this article.

CONTACT PROCESS ON HEXAGONAL LATTICE

In this article, we discuss several properties of the basic contact process on hexagonal lattice H, showing that it behaves quite similar to the process on d-dimensional lattice Zd in many aspects. Firstly, we construct a coupling between the contact process on hexagonal lattice and the oriented percolation, and prove an equivalent finite space-time condition for the survival of the process. Secondly, we show the complete convergence theorem and the polynomial growth hold for the contact process on hexagonal lattice. Finally, we prove exponential bounds in the supercritical case and exponential decay rates in the subcritical case of the process.

The Printing and Firing Process of Al Paste in PTC Ohmic Contact Electrodes

Al electrodes are well known as ohmic contact electrodes for the PTC component , the influence of their thickness on final component properties was investigated by comparing their ohmic characteristics with the ones of InGa electrodes . After observing the Al paste physical and chemical behaviors during rising temperature by thermal analysis (DTA), the firing operation of Al electrodes could be divided into three main subsections: the temperature rising time (t-r), the peak firing temperature (T-p) and the hold time at peak firing temperature (t-h). The effects of these three parameters on final component properties were discussed in detail.

COMPLETE CONVERGENCE THEORY OF THE CONTACT PROCESS ON T_d×Z

The author considers the contact process on a branching plane Td×Z, which is the product of a regular tree Td and the line Z. It is shown that above the second critical point, the complete convergence theory holds.

DIFFERENCE SCHEME FOR TWO-PHASE FLOW

A numerical method for two-phase flow with hydrodynamics behavior was considered. The nonconservative hyperbolic governing equations proposed by Saurel and Gallout were adopted. Dissipative effects were neglected but they could be included in the model without major difficulties. Based on the opinion proposed by Abgrall that “a two phase system, uniform in velocity and pressure at t=0 will be uniform on the same variable during its temporal evolution", a simple accurate and fully Eulerian numerical method was presented for the simulation of multiphase compressible flows in hydrodynamic regime. The numerical method relies on Godunov-type scheme, with HLLC and Lax-Friedrichs type approximate Riemann solvers for the resolution of conservation equations, and nonconservative equation. Speed relaxation and pressure relaxation processes were introduced to account for the interaction between the phases. Test problem was presented in one space dimension which illustrated that our scheme is accurate, stable and oscillation free.

Modeling of Energy Processes in Wheel-Rail Contacts Operating under Influence of Periodic Discontinuous Forces

In this paper we present new numerical simulation approaches for determining the energy processes under periodic conditions caused by time-discontinuous forces in the wheel-rail contacts. The main advantage of the presented method is the total elimination of frequency analysis, which in effect introduces important simplifications in the identification of the effects in the contact. The second important feature is the fact that the method is based on the analysis of appropriate loops on the energy phase plane leading to an easy estimation of the rail strength through the evaluation of the loop’s area. That model based simulation in the applied dynamics relies on advanced methods for model setup, robust and efficient numerical solution techniques and powerful simulation tools for practical applications. Fundamental properties of contact displacements of the rail surface have been considered on the basis of the newly established method. The contact zone between railway wheels and the rail surfaces made of bulk materials is perceived as strong enough to resist the normal (vertical) forces introduced by heavy loads and the dynamic response induced by track and wheel irregularities. The analysis is carried out for a wheel running on an elastic rail rested on sleepers arranged on completely rigid foundation. The equations of displacement motion are established through the application of the Lagrange equations approach. The established model of the wheel-rail contact dynamics has been applied to that same roll plane but with taking into account a nonlinear characteristic of the sleeper with respect to the ground. Attention then is focused completely on the modeling of the energy absorbed by the rail. The applied method employs the energy state variables as time functions leading to determine the susceptibility of a given contact on the strength induced by the rail roll.

Business Process Analysis and Simulation: The Contact Center of a Public Health and Social Information Office

This article proposes a framework, called BP-M* which includes: 1) a methodology to analyze, engineer, restructure and implement business processes, and 2) a process model that extends the process diagram with the specification of resources that execute the process activities, allocation policies, schedules, times of activities, management of queues in input to the activities and workloads so that the same model can be simulated by a discrete event simulator. The BP-M* framework has been applied to a real case study, a public Contact Center which provides different typologies of answers to users’ requests. The simulation allows to study different system operating scenarios (“What-If” analysis) providing useful information for analysts to evaluate restructuring actions.

SMALL DENSITY FLUCTUTAION FOR ONE DIMENSIONAL CONTACT PROCESSES UNDER NONEQUILIBRIUM

This paper shows that for a supercritical contact process in one dimension, if the initial distribution satisfies reasonable hypothesis, then the first hitting time of certain set with anomalous small density is asymptotically exponentially distributed. We also show the similar result for the contact process on the finite set [0, N].

Existence and numerical approximation of a solution to frictional contact problem for electro-elastic materials

In this paper,a frictional contact problem between an electro-elastic body and an electrically conductive foundation is studied.The contact is modeled by normal compliance with finite penetration and a version of Coulomb’s law of dry friction in which the coefficient of friction depends on the slip.In addition,the effects of the electrical conductivity of the foundation are taken into account.This model leads to a coupled system of the quasi-variational inequality of the elliptic type for the displacement and the nonlinear variational equation for the electric potential.The existence of a weak solution is proved by using an abstract result for elliptic variational inequalities and a fixed point argument.Then,a finite element approximation of the problem is presented.Under some regularity conditions,an optimal order error estimate of the approximate solution is derived.Finally,a successive iteration technique is used to solve the problem numerically and a convergence result is established.

Preparation and microstructure characterization of a nano-sized Ti^(4+)-doped AgSnO_2 electrical contact material

A Ti^4＋-doped nano-structured AgSnO2 material was prepared using sol-gel method and characterized by X-ray diffraction （XRD）, transmission electron microscopy （TEM）, and scanning electron microscopy （SEM）. The results show that Ti^4＋ cations are successfully doped into the crystal lattice of SnO2, and thus significantly improve the electrical conductivity of the sample. Furthermore, the coating of Ag on Ti^4＋-doped SnO2 nano-sized particles enhances the surface wettability and enables the resulting AgSnO2 material to have better mechanical properties.

Machine Vision Based Measurement of Dynamic Contact Angles in Microchannel Flows

When characterizing flows in miniaturized channels, the determination of the dynamic contact angle is important. By measuring the dynamic contact angle, the flow properties of the flowing liquid and the effect of material properties on the flow can be characterized. A machine vision based system to measure the contact angle of front or rear menisci of a moving liquid plug is described in this article. In this research, transparent flow channels fabricated on thermoplastic polymer and sealed with an adhesive tape are used. The transparency of the channels enables image based monitoring and measurement of flow variables, including the dynamic contact angle. It is shown that the dynamic angle can be measured from a liquid flow in a channel using the image based measurement system. An image processing algorithm has been developed in a MATLAB environment. Images are taken using a CCD camera and the channels are illuminated using a custom made ring light. Two fitting methods, a circle and two parabolas, are experimented and the results are compared in the measurement of the dynamic contact angles.

Numerical simulation of mould filling process for pressure plate and valve handle in LFC

In lost foam casting (LFC), the distribution of polymer beads during the bead filling process is not uniform, and the collision between polymer beads determines the distribution of two-phase flow of gas and solid. The interaction between the gas and solid phases reveals as coupling effect of the force that gas exerts on particles or vice versa, or that among particles. The gas-solid flow in filling process is nonlinearity, which makes the coupling effect an essential point to carry out a simulation properly. Therefore, information of each particle's motion is important for acquiring the law of filling process. In bead filling process, compressed air is pressed into mold cavity, and discharged from gas vent, creating a pressure difference between outer and inner space near the gas vent. This pressure difference directly changes the spatial distribution and motion trace of gas and solid phases. In this paper, Discrete Element Method (DEM) and Computational Fluid Dynamics (CFD) are employed to simulate the fluid dynamic character based on Newton's Third Law of Motion. The simulation results of some casting products such as pressure plate and valve handle are compared with the result obtained from practical experiment in order to test the feasibility of DEM. The comparison shows that this DEM method can be a very promising tool in the mould filling simulation of beads' movement.

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strengthand high electrical conductivity, Cu-Cr alloy series were selected asmaterials and cu-Cr alloy castings were produced by means ofdirectional solidification continu- ous casting (DSCC) process. theresults show that the fibrillar strengthening phase, β-Cr, orderlyarranges among the copper matrix phase along the wire direction; andmicrostructure of in-situ composite forms, which retains the basicproperty of good conductivity of the copper matrix and meanwhileobtains the strengthening effect ofβ-Cr phase.