Tree plantation and forest restoration are the major strategies for enhancing terrestrial carbon sequestration and mitigating climate change.The Grain for Green Project in China has positively impacted global carbon s...Tree plantation and forest restoration are the major strategies for enhancing terrestrial carbon sequestration and mitigating climate change.The Grain for Green Project in China has positively impacted global carbon sequestration and the trend towards fragmentation of plantation forests.Limited studies have been conducted on changes in plantation biomass and stand structure caused by fragmentation,and the effect of fragmentation on the carbon storage of plantation forests remains unclear.This study evaluated the differences between carbon storage and stand structure in black locust forests in fragmented and continuous landscape in the Ansai District,China and discussed the effects of ecological significance of four landscape indices on carbon storage and tree density.We used structural equation modelling to explore the direct and indirect effects of fragmentation,edge,abiotic factors,and stand structure on above-ground carbon storage.Diameter at breast height(DBH)in fragmented forests was 53.3%thicker,tree density was 40.9%lower,and carbon storage was 49.8%higher than those in continuous forests;for all given DBH>10 cm,the trees in fragmented forests were shorter than those in continuous forests.The patch area had a negative impact on carbon storage,i.e.,the higher the degree of fragmentation,the lower the density of the tree;and fragmentation and distance to edge(DTE)directly increased canopy coverage.However,canopy coverage directly decreased carbon storage,and fragmentation directly increased carbon storage and tree density.In non-commercial forests,fragmentation reduces the carbon storage potential of plantation,and the influence of patch area,edge,and patchy connection on plantation should be considered when follow-up trees are planted and for the plantation management.Thus,expanding the area of plantation patches,repairing the edges of complex-shaped patches,enhancing the connectivity of similar patches,and applying nutrients to plantation forests at regular intervals are recommended in fragmented areas of the Loess Plateau.展开更多
Metal tellurides(MTes) are highly attractive as promising anodes for high-performance potassium-ion batteries. The capacity attenuation of most reported MTe anodes is attributed to their poor electrical conductivity a...Metal tellurides(MTes) are highly attractive as promising anodes for high-performance potassium-ion batteries. The capacity attenuation of most reported MTe anodes is attributed to their poor electrical conductivity and large volume variation. The evolution mechanisms, dissolution properties, and corresponding manipulation strategies of intermediates(K-polytellurides, K-pTe_(x)) are rarely mentioned. Herein,we propose a novel structural engineering strategy to confine ultrafine CoTe_(2) nanodots in hierarchical nanogrid-in-nanofiber carbon substrates(CoTe_(2)@NC@NSPCNFs) for smooth immobilization of K-pTe_(x) and highly reversible conversion of CoTe_(2) by manipulating the intense electrochemical reaction process. Various in situ/ex situ techniques and density functional theory calculations have been performed to clarify the formation, transformation, and dissolution of K-pTe_(x)(K_(5)Te_(3) and K_(2)Te), as well as verifying the robust physical barrier and the strong chemisorption of K_(5)Te_(3) and K_(2)Te on S, N co-doped dual-type carbon substrates. Additionally, the hierarchical nanogrid-in-nanofiber nanostructure increases the chemical anchoring sites for K-pTe_(x), provides sufficient volume buffer space, and constructs highly interconnected conductive microcircuits, further propelling the battery reaction to new heights(3500 cycles at 2.0 A g^(-1)). Furthermore, the full cells further demonstrate the potential for practical applications. This work provides new insights into manipulating K-pTe_(x) in the design of ultralong-cycling MTe anodes for advanced PIBs.展开更多
The effects of annealing treatment on the microstructure and electrochemical properties of low-Co LaNi 3.55 Mn 0.35 Co 0.20 Al 0.20 Cu 0.75 Fe 0.10 hydrogen storage alloys were investigated. X-ray diffraction (XRD) ...The effects of annealing treatment on the microstructure and electrochemical properties of low-Co LaNi 3.55 Mn 0.35 Co 0.20 Al 0.20 Cu 0.75 Fe 0.10 hydrogen storage alloys were investigated. X-ray diffraction (XRD) analysis indicated that annealing treatment remarkably reduced the lattice strain and defects, and increased the unit-cell volume. The optical microscope analysis showed that the as-cast alloy had a crass dendrite microstructure with noticeable composition segregation, which gradually disappeared with increasing annealing temperature, and the micro-structure changed to an equiaxed structure after annealing the alloy at 1233 K. The electrochemical tests indicated that the annealed alloys demonstrated much better cycling stability compared with the as-cast one. The capacity retention at the 100th cycle increased from 90.0% (as-cast) to 94.7% (1273 K). The annealing treatment also improved the discharge capacity. However, the high rate dischargeability (HRD) value of the annealed alloy slightly dropped, which was believed to be ascribed to the decreased exchange current density and the hydrogen diffusion coefficient in alloy bulk.展开更多
To improve the electrochemical properties of rare-earth-Mg-Ni-based hydrogen storage alloys, the effects of stoichiometry and Cu-substitution on the phase structure and thermodynamic properties of the alloys were stud...To improve the electrochemical properties of rare-earth-Mg-Ni-based hydrogen storage alloys, the effects of stoichiometry and Cu-substitution on the phase structure and thermodynamic properties of the alloys were studied. Nonsubstituted Ml0.80Mg0.20(Ni2.90Co0.50-Mn0.30Al0.30)x (x=0.68, 0.70, 0.72, 0.74, 0.76) alloys and Cu-substituted Ml0.80Mg0.20(Ni2.90Co0.50-yCuyMn0.30Al0.30)0.70 (y=0, 0.10, 0.30, 0.50) alloys were prepared by induction melting. Phase structure analysis shows that the nonsubstituted alloys consist of a LaNi5 phase, a LaNi3 phase, and a minor La2Ni7 phase;in addition, in the case of Cu-substitution, the Nd2Ni7 phase appears and the LaNi3 phase vanishes. Ther-modynamic tests show that the enthalpy change in the dehydriding process decreases, indicating that hydride stability decreases with in-creasing stoichiometry and increasing Cu content. The maximum discharge capacity, kinetic properties, and cycling stability of the alloy electrodes all increase and then decrease with increasing stoichiometry or increasing Cu content. Furthermore, Cu substitution for Co ame-liorates the discharge capacity, kinetics, and cycling stability of the alloy electrodes.展开更多
The phase structure and hydrogen storage properties of LaMg 3.70 Ni 1.18 alloy were investigated. The LaMg 3.70 Ni 1.18 alloy consists of main LaMg 2 Ni phase, minor La 2 Mg 17 and LaMg 3 phases. The alloy can be acti...The phase structure and hydrogen storage properties of LaMg 3.70 Ni 1.18 alloy were investigated. The LaMg 3.70 Ni 1.18 alloy consists of main LaMg 2 Ni phase, minor La 2 Mg 17 and LaMg 3 phases. The alloy can be activated in the first hydriding/dehydriding process, and initial LaMg 2 Ni, La 2 Mg 17 , and LaMg 3 phases transfer to LaH 2.34 , Mg, and Mg 2 Ni phases after activation. The reversible hydrogen storage capacity of the LaMg 3.70 Ni 1.18 alloy is 2.47 wt.% at 558 K, which is higher than that of the LaMg 2 Ni alloy. The pressure-composition-temperature (PCT) curves display two hydriding plateaus, corresponding to the formation of MgH 2 and Mg 2 NiH 4 . However, only one dehydriding plateau is observed, owing to the synergetic effect of hydrogen desorption between MgH 2 and Mg 2 NiH 4 . The uptake time for hydrogen content to reach 99% of saturated state is less than 250 s, and 90% hydrogen can be released in 1200 s in the experimental conditions, showing fast kinetics in hydriding and dehydriding. The activation energies of the LaMg 3.70 Ni 1.18 alloy are –51.5 ± 1.1 kJ/mol and –57.0 ± 0.6 kJ/mol for hydriding and dehydriding, respectively. The hydriding/dehydriding kinetics of the LaMg 3.70 Ni 1.18 alloy is better than that of the Mg 2 Ni alloy, owing to the lower activation energy values.展开更多
In order to improve the cycle stability of La-Mg-Ni-Co type alloy electrode, rapid quenching technology was employed. The effects of rapid quenching on the microstructure and cycle stability of the alloy were investig...In order to improve the cycle stability of La-Mg-Ni-Co type alloy electrode, rapid quenching technology was employed. The effects of rapid quenching on the microstructure and cycle stability of the alloy were investigated. The obtained results show that the La2Mg(Ni0.85Co0.15)9M0.1 (M=B, Cr) alloy electrodes are composed of (La, Mg)Ni3 phase, LaNi5 phase and a small amount of the LaNi2 phase. A trace of the Ni2B phase exists in the as-cast MB alloy, and the Ni2B phase in the alloy nearly disappears after rapid quenching. Rapid quenching technology can slightly improve the cycling life of the alloy. When the quenching rate increases from 0 m·s-1 (As-cast is defined as quenching rate of 0 m·s-1) to 30 m·s-1, the cycle lives of the MB, MCr alloys enhance from 86 and 87 cycles to 106 and 119 cycles, respectively. On the other hand, the average capacity decay rates of the MB, MCr alloys decrease from 1.7172 and 1.7178 mAh·g-1·cycle-1 to 1.5751 and 1.3060 mAh·g-1·cycle-1 after 86 charge-discharges cycling, respectively.展开更多
The crystal structure, phase abundance and the electrochemical properties of Zr(Mn1-x Nix)2 (0.40 ≤x≤0.75) alloys were investigated by means of XRD, Rietveld refinement method and electrochemical measurements. The a...The crystal structure, phase abundance and the electrochemical properties of Zr(Mn1-x Nix)2 (0.40 ≤x≤0.75) alloys were investigated by means of XRD, Rietveld refinement method and electrochemical measurements. The alloys are multiphase. C15 Laves phase occurs as a main phase accompanying with C14 phase and other minor phases, indicating that Ni element is C15-stabilized element for ZrMn2 alloy. The phase abundance and lattice parameters of Laves phase are influenced significantly by Ni substitution. The Zr(Mn0.45 Ni0.55)2 alloy with the highest amount of C15 phase exhibits the maximum electrochemical capacity of 242m Ah/g. C14 phase occurring in Zr-Mn-Ni alloys is beneficial for the electrochemical kinetics of hydride electrodes.展开更多
The content and composition of wheat storage proteins are the major determinants of dough rheological properties and breadmaking quality and are influenced by cultivation conditions.This study aimed to investigate the...The content and composition of wheat storage proteins are the major determinants of dough rheological properties and breadmaking quality and are influenced by cultivation conditions.This study aimed to investigate the effects of water deficit and high N-fertilizer application on wheat storage protein synthesis,gluten secondary structure,and breadmaking quality.Reverse-phase ultrahigh-performance liquid chromatography analysis showed that storage protein and gluten macropolymer accumulation was promoted under both independent applications and a combination of water-deficit and high N-fertilizer treatments.Fourier-transform infrared spectroscopy showed that water deficit and high N-fertilizer treatments generally improved protein secondary structure formation and lipid accumulation,and reduced flour moisture.In particular,high N-fertilizer application increasedβ-sheet content by 10.4%and the combination of water-deficit and high N-fertilizer treatments increased random coil content by 7.6%.These changes in gluten content and secondary structure led to improved dough rheological properties and breadmaking quality,including superior loaf internal structure,volume,and score.Our results demonstrate that moderately high N-fertilizer application under drought conditions can improve gluten accumulation,gluten secondary structure formation,and baking quality.展开更多
The stoichiometric alloy MlB5.0 and the hypo-stoichiometric alloy MlB4.85 were prepared by twin-roller rapid quenching process, and their structure and electrochemical properties were studied. The results of XRD show ...The stoichiometric alloy MlB5.0 and the hypo-stoichiometric alloy MlB4.85 were prepared by twin-roller rapid quenching process, and their structure and electrochemical properties were studied. The results of XRD show that both of the alloys have a typical single-phase hexagonal CaCus-type structure. The cell volume of the hylpo-stoichiometric alloy M1B4.85 is slightly larger than that of the stoichiometric alloy M1B5.0, although its lattice constant cla is smaller. Under 2 C discharging rate, i.e. 640 mA/g, the M1B4.85 has a discharge capacity of 320 mAh/g, which is higher than that of the M1Bs.o, 312 mAh/g. Nevertheless, the capacities of the M1B4.85 and the M1Bs.o decline 24.7% and 20.2% after 400 cycles, respectively. The relationship of electrochemical performances of the alloys with their structures is discussed.展开更多
Mm0.3Ml0.7Ni3.55Co0.75Mn0.4-Al0.3 alloy has high chemical activity and favorable plateaus pressure. Mg2Ni is in favor of high hydrogen storage capacity and low weight, but it is difficult to be activated. In order to ...Mm0.3Ml0.7Ni3.55Co0.75Mn0.4-Al0.3 alloy has high chemical activity and favorable plateaus pressure. Mg2Ni is in favor of high hydrogen storage capacity and low weight, but it is difficult to be activated. In order to improve the capacity and cycle performances of hydrogen-storage alloy electrodes, Mm0.3Ml0.7Ni3.55Co0.75Mn0.4-Al0.3-x%Mg2Ni(x=0, 5, 10, 30) composite hydrogen storage alloys prepared by two-step re-melting were investigated in this work. The influences of Mg2Ni content on the cycle stabilities were analyzed by electrochemical methods. It was observed by XRD that the main phase of all the alloys is LaNi5 and the crystal lattice parameters of LaNi5 are changed with the increasing of x value, i.e, a-axis and unit cell volume decrease and c-axis decreases nonlinearly. The c-axis of alloy with x=5 is larger than the others. With the increasing of x value, capacity retentions of the composite hydrogen storage alloys rise from 66.21% while x=0 to 82.04% while x=10, but the capacity retention of the composite alloy with 30% Mg2Ni declines because of its decreasing axial ratio. More over, the composite alloy with 5% Mg2Ni shows the best cycle stability and higher discharge capacity, and it is an appropriate candidate for battery materials.展开更多
The interfacial performance of implanted neural electrodes is crucial for stimulation safety and the recording quality of neuronal activity.This paper proposes a novel surface architecture and optimization strategy fo...The interfacial performance of implanted neural electrodes is crucial for stimulation safety and the recording quality of neuronal activity.This paper proposes a novel surface architecture and optimization strategy for the platinum–iridium(Pt–Ir)electrode to optimize electrochemical performance and wettability.A series of surface micro/nano structures were fabricated on Pt–Ir electrodes with different combinations of four adjustable laser-processing parameters.Subsequently,the electrodes were characterized by scanning electron microscopy,energy-dispersive X-ray spectroscopy,cyclic voltammetry,electrochemical impedance spectroscopy,and wetting behavior.The results show that electrode performance strongly depends on the surface morphology.Increasing scanning overlap along with moderate pulse energy and the right number of pulses leads to enriched surface micro/nano structures and improved electrode performance.It raises the maximum charge storage capacity to 128.2 mC/cm^(2) and the interface capacitance of electrodes to 3.0×10^(4)μF/cm^(2) for the geometric area,compared with 4.6 mC/cm^(2) and 443.1μF/cm2,respectively,for the smooth Pt–Ir electrode.The corresponding optimal results for the optically measured area are 111.8 mC/cm^(2) and 2.6×10^(4)μF/cm^(2),which indicate the contribution of fner structures to the ablation profle.The hierarchical structures formed by the femtosecond laser dramatically enhanced the wettability of the electrode interface,giving it superwicking properties.A wicking speed of approximately 80 mm/s was reached.Our optimization strategy,leading to superior performance of the superwicking Pt–Ir interface,is promising for use in new neural electrodes.展开更多
Rare earth-Mg-Ni-based alloys with superlattice structures are new generation negative electrode materials for the nickel metal hydride batteries.Among them,the novel AB_(4)-type superlattice structure alloy is suppos...Rare earth-Mg-Ni-based alloys with superlattice structures are new generation negative electrode materials for the nickel metal hydride batteries.Among them,the novel AB_(4)-type superlattice structure alloy is supposed to have superior cycling stability and rate capability.Yet its preparation is hindered by the crucial requirement of temperature and the special composition which is close to the other superlattice structure.Here,we prepare rare earth-Mg-Ni-based alloy and study the phase transformation of alloys to make clear the formation of AB_(4)-type phase.It is found Pr_(5)Co_(19)-type phase is converted from Ce_(5)Co_(19)-type phase and shows good stability at higher temperature compared to the Ce_(5)Co_(19)-type phase in the range of 930-970℃.Afterwards,with further 5℃increasing,AB_(4)-type superlattice structure forms at a temperature of 975℃by consuming Pr_(5)Co_(19)-type phase.In contrast with A_(5)B_(19)-type alloy,AB_(4)-type alloy has superior rate capability owing to the dominant advantages of charge transfer and hydrogen diffusion.Besides,AB_(4)-type alloy shows long lifespan whose capacity retention rates are 89.2%at the 100;cycle and 82.8%at the 200;cycle,respectively.AB_(4)-type alloy delivers 1.53 wt.%hydrogen storage capacity at room temperature and exhibits higher plateau pressure than Pr_(5)Co_(19)-type alloy.The work provides novel AB_(4)-type alloy with preferable electrochemical performance as negative electrode material to inspire the development of nickel metal hydride batteries.展开更多
Up to now,three kinds of ion-storage mechanisms are summarized towards anode materials in lithium/sodium-ion batteries,but they have low capacity and poor cyclic performance.Therefore,it is necessary to develop a new ...Up to now,three kinds of ion-storage mechanisms are summarized towards anode materials in lithium/sodium-ion batteries,but they have low capacity and poor cyclic performance.Therefore,it is necessary to develop a new approach to optimize ion storage.Herein,we report an adsorption/desorption storage route through engineering electronic structure of cation-deficient Ti_(1-x)O_(2)nanosheets.Ti_(1-x)O_(2)nanosheets indeed exhibit higher capacity(332.1 mA h g^(-1)vs.137.7 mA h g^(-1)for LIBs,195.7 mA h g^(-1)vs.111 mA h g^(-1)for SIBs),and more stable cyclic performance(296 mA h g^(-1)vs.99 mA h g^(-1)for LIBs,178.1 mA h g^(-1)vs.80.2 mA h g^(-1)for SIBs after 100 cycles)at 0.1 A g^(-1)than TiO_(2)nanosheets.Kinetics analysis and density functional theory(DFT)calculations reveal that electronic structures of vacancy within Ti_(1-x)O_(2) nanosheets encourage a novel adsorption-desorption storage route.These results highlight the benefits of the engineered electronic structures within electrode material and implement novel ion-storage mechanism towards broad energy storage applications.展开更多
There was an obvious relationship between seed testa structure, storage material and resistance to A. flavus of peanut. Results showed that seed testa of peanut germplasm with high resistance (HR) to A. flavus infec...There was an obvious relationship between seed testa structure, storage material and resistance to A. flavus of peanut. Results showed that seed testa of peanut germplasm with high resistance (HR) to A. flavus infection had thicker wax layer, integrated and tight epidermis layer, regular vascular tissue range. However, the seed testa of peanut germplasm with high sensitivity (HS) to A. flavus had the reverse results, and results of those with medium resistance (MR) to A. flavus lay in between, but changes of testa thickness were not significant among different resistance kinds. Results also showed that some seed storage materials were closely related with resistance potential to A. flavus. It seemed that varieties with higher resistance to A. flavus had higher oleic acid and protein content, lower linoleic acid and fat content. Content of palm acid, total sugar and VE did not show positive relationship with the resistance to A. flavus.展开更多
Rational architecture design has turned out to be an effective strategy in improving the electrochemical performance of electrode materials for batteries.However,an elaborate structure that could simultaneously endow ...Rational architecture design has turned out to be an effective strategy in improving the electrochemical performance of electrode materials for batteries.However,an elaborate structure that could simultaneously endow active materials with promoted reaction reversibility,accelerated kinetic and restricted volume change still remains a huge challenge.Herein,a novel chemical interaction motivated structure design strategy has been proposed,and a chemically bonded Co(CO_(3))_(0.5)OH·0.11 H_(2)O@MXene(CoCH@MXene)layered-composite was fabricated for the first time.In such a composite,the chemical interaction between Co^(2+)and MXene drives the growth of smaller-sized CoCH crystals and the subsequent formation of interwoven CoCH wires sandwiched in-between MXene nanosheets.This unique layered structure not only encourages charge transfer for faster reaction dynamics,but buffers the volume change of CoCH during lithiation-delithiation process,owing to the confined crystal growth between conductive MXene layers with the help of chemical bonding.Besides,the sandwiched interwoven CoCH wires also prevent the stacking of MXene layers,further conducive to the electrochemical performance of the composite.As a result,the as-prepared CoCH@MXene anode demonstrates a high reversible capacity(903.1 mAh g^(-1)at 100 mA g^(-1))and excellent cycling stability(maintains 733.6 mAh g^(-1)at1000 mA g^(-1)after 500 cycles)for lithium ion batteries.This work highlights a novel concept of layerby-layer chemical interaction motivated architecture design for futuristic high performance electrode materials in energy storage systems.展开更多
The rare earth based hydrogen storage alloys MmxM1 1 - x ( Ni3.55 Co0.75 Mn0.4 A10.3 ) ( x = 0 ~ 0.5 ) were investigated in this work.Adjusted Ml: Mm ratio to change the content of La,Ce,Pr and Nd in the alloys and t...The rare earth based hydrogen storage alloys MmxM1 1 - x ( Ni3.55 Co0.75 Mn0.4 A10.3 ) ( x = 0 ~ 0.5 ) were investigated in this work.Adjusted Ml: Mm ratio to change the content of La,Ce,Pr and Nd in the alloys and then to change the phase structure, the influences of phase structure on the electrochemical properties were analyzed.The results indicate that the main phase of all alloys is LaNi5 with CaCu5 type structure and the crystal lattices constants of LaNi5 are changed with increasing x value, i.e, decreased a-axis, increased c-axis and axis ratio and nonlinear decreased crystal volume.The crystal volume of the alloy with x = 0.3 is larger than others.There is second phase A1LaNi4 in alloys when x≥0.3, which decrease the discharge capacity, but increase the cycling stability and high rate discharge ability.Compared comprehensively, the alloy with x = 0.3 shows the higher discharge capacity and the better cycling stability.展开更多
MgNi-based hydrogen storage alloys Mg1–xTixNi (x = 0, 0.1, 0.2, and 0.3) were prepared by means of mechanical alloying. Mg in the alloy was partially substituted by Ti to improve the cycle stability of the alloys. ...MgNi-based hydrogen storage alloys Mg1–xTixNi (x = 0, 0.1, 0.2, and 0.3) were prepared by means of mechanical alloying. Mg in the alloy was partially substituted by Ti to improve the cycle stability of the alloys. The effects of the substitution of Ti for Mg on the microstructure and electrochemical performances of the alloys were investigated in detail. The results indicate that the substitution of Ti for Mg obviously decreases the discharge capacity, but it significantly improves their cycle stabilities. The microstructure of the alloys analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM) shows that the alloys have a dominatingly amorphous structure. The substitution of Ti for Mg helps to improve the anti-oxidation/corrosion ability of the MgNi alloy but demolishes the electrochemical kinetics of hydrogenation/dehydrogenation. The Mg0.9Ti0.1Ni alloy electrode milled for 80 h exhibits the best integrative capability, which has the maximal discharge capacity of 331.66 mAh/g and the C30/Cmax of 63.65%.展开更多
The phase structure and electrochemical characteristics of Ml ((Ni3.55Co0.75Mn0.40Al0.30)sx ( x = 0.88, 0.92, 0.96, 1.00) hydrogen storage alloys were studied. The effect of the stoichiometric ratio on the phase ...The phase structure and electrochemical characteristics of Ml ((Ni3.55Co0.75Mn0.40Al0.30)sx ( x = 0.88, 0.92, 0.96, 1.00) hydrogen storage alloys were studied. The effect of the stoichiometric ratio on the phase structure and electrochemical characteristics was analyzed. The results of XRD reveal that all the alloys consist mainly of LaNi5 phase with the hexagonal CaCu5 structure. But a few of the diffraction peaks of La2Ni7 phase on XRD pattern are observed when x ≤ 0.92, and with decreasing x, the intensity of La2Ni7 diffraction peaks increases and the values of lattice parameters a and cell volume increase, c and c/a of LaNi5 phase decrease gradually. When x≥0.96, La2Ni7 phase disappears and the alloys become single CaCu5-type. The electrochemical tests show that the maximum discharge capacity, high rate dischargeability and low temperature dischargeability are improved to different degrees by adjusting the stoichiometric ratio.展开更多
Structure and electrochemical properties of (La, Ce, Pr, Nd)_2MgNi_9 hydrogen storage alloys were investigated through orthogonal design experiments, and the alloys were obtained through induction melting followed by ...Structure and electrochemical properties of (La, Ce, Pr, Nd)_2MgNi_9 hydrogen storage alloys were investigated through orthogonal design experiments, and the alloys were obtained through induction melting followed by annealing treatment. The structure of main phase in alloys belongs to PuNi_3-type with a space group R3m. Rare earth elements, as a substitute of lanthanum, have a significant effect on phase structure of alloys, elements of cerium and neodymium are beneficial to the formation of Gd_2Co_7-type phase with a space group P 6_3/mmc. Rare earth elements can decrease the unit cell volume of main phase of alloys dramatically, and increase the axis ratio. The results of electrochemical experiment showed that the discharge capacity of alloy electrodes ranged from 342.97 to 380.68 mAh·g -1, and elements of cerium and neodymium can reduce the discharge capacity of alloy electrodes significantly. Compared to the electrode of La_2MgNi_9 alloy, the substitution of lanthanum by rare earth elements did not improve the cyclic stability of alloy electrodes due to the anisotropic structure change of unit cell. While rare-earth elements can improve the high rate dischargeability of alloy electrodes, the high rate dischargeability of alloy electrodes could reach the maximum when the unit cell volume of PuNi_3-type structure was about 0532 nm.展开更多
基金supported by the National Natural Science Foundation of China(32201429)the College of Landscape Architecture and Art,Northwest A&F University,China.
文摘Tree plantation and forest restoration are the major strategies for enhancing terrestrial carbon sequestration and mitigating climate change.The Grain for Green Project in China has positively impacted global carbon sequestration and the trend towards fragmentation of plantation forests.Limited studies have been conducted on changes in plantation biomass and stand structure caused by fragmentation,and the effect of fragmentation on the carbon storage of plantation forests remains unclear.This study evaluated the differences between carbon storage and stand structure in black locust forests in fragmented and continuous landscape in the Ansai District,China and discussed the effects of ecological significance of four landscape indices on carbon storage and tree density.We used structural equation modelling to explore the direct and indirect effects of fragmentation,edge,abiotic factors,and stand structure on above-ground carbon storage.Diameter at breast height(DBH)in fragmented forests was 53.3%thicker,tree density was 40.9%lower,and carbon storage was 49.8%higher than those in continuous forests;for all given DBH>10 cm,the trees in fragmented forests were shorter than those in continuous forests.The patch area had a negative impact on carbon storage,i.e.,the higher the degree of fragmentation,the lower the density of the tree;and fragmentation and distance to edge(DTE)directly increased canopy coverage.However,canopy coverage directly decreased carbon storage,and fragmentation directly increased carbon storage and tree density.In non-commercial forests,fragmentation reduces the carbon storage potential of plantation,and the influence of patch area,edge,and patchy connection on plantation should be considered when follow-up trees are planted and for the plantation management.Thus,expanding the area of plantation patches,repairing the edges of complex-shaped patches,enhancing the connectivity of similar patches,and applying nutrients to plantation forests at regular intervals are recommended in fragmented areas of the Loess Plateau.
基金supported by the National Natural Science Foundation of China (Grant Nos. 51920105004, 52102223, 52002081)。
文摘Metal tellurides(MTes) are highly attractive as promising anodes for high-performance potassium-ion batteries. The capacity attenuation of most reported MTe anodes is attributed to their poor electrical conductivity and large volume variation. The evolution mechanisms, dissolution properties, and corresponding manipulation strategies of intermediates(K-polytellurides, K-pTe_(x)) are rarely mentioned. Herein,we propose a novel structural engineering strategy to confine ultrafine CoTe_(2) nanodots in hierarchical nanogrid-in-nanofiber carbon substrates(CoTe_(2)@NC@NSPCNFs) for smooth immobilization of K-pTe_(x) and highly reversible conversion of CoTe_(2) by manipulating the intense electrochemical reaction process. Various in situ/ex situ techniques and density functional theory calculations have been performed to clarify the formation, transformation, and dissolution of K-pTe_(x)(K_(5)Te_(3) and K_(2)Te), as well as verifying the robust physical barrier and the strong chemisorption of K_(5)Te_(3) and K_(2)Te on S, N co-doped dual-type carbon substrates. Additionally, the hierarchical nanogrid-in-nanofiber nanostructure increases the chemical anchoring sites for K-pTe_(x), provides sufficient volume buffer space, and constructs highly interconnected conductive microcircuits, further propelling the battery reaction to new heights(3500 cycles at 2.0 A g^(-1)). Furthermore, the full cells further demonstrate the potential for practical applications. This work provides new insights into manipulating K-pTe_(x) in the design of ultralong-cycling MTe anodes for advanced PIBs.
基金supported by the National Natural Science Foundation of China (No. 20673093)the Natural Science Foundation of Hebei Province, China (No. B2007000303)
文摘The effects of annealing treatment on the microstructure and electrochemical properties of low-Co LaNi 3.55 Mn 0.35 Co 0.20 Al 0.20 Cu 0.75 Fe 0.10 hydrogen storage alloys were investigated. X-ray diffraction (XRD) analysis indicated that annealing treatment remarkably reduced the lattice strain and defects, and increased the unit-cell volume. The optical microscope analysis showed that the as-cast alloy had a crass dendrite microstructure with noticeable composition segregation, which gradually disappeared with increasing annealing temperature, and the micro-structure changed to an equiaxed structure after annealing the alloy at 1233 K. The electrochemical tests indicated that the annealed alloys demonstrated much better cycling stability compared with the as-cast one. The capacity retention at the 100th cycle increased from 90.0% (as-cast) to 94.7% (1273 K). The annealing treatment also improved the discharge capacity. However, the high rate dischargeability (HRD) value of the annealed alloy slightly dropped, which was believed to be ascribed to the decreased exchange current density and the hydrogen diffusion coefficient in alloy bulk.
基金supported by the National Natural Science Foundation of China(Nos.21303157 and 21106123)the Natural Science Foundation of Hebei Province,China(No.B2012203104)+1 种基金the China Postdoctoral Science Foundation Project(2013M541201)the Research Fund for the Doctoral Program of Higher Education of China(20131333120008)
文摘To improve the electrochemical properties of rare-earth-Mg-Ni-based hydrogen storage alloys, the effects of stoichiometry and Cu-substitution on the phase structure and thermodynamic properties of the alloys were studied. Nonsubstituted Ml0.80Mg0.20(Ni2.90Co0.50-Mn0.30Al0.30)x (x=0.68, 0.70, 0.72, 0.74, 0.76) alloys and Cu-substituted Ml0.80Mg0.20(Ni2.90Co0.50-yCuyMn0.30Al0.30)0.70 (y=0, 0.10, 0.30, 0.50) alloys were prepared by induction melting. Phase structure analysis shows that the nonsubstituted alloys consist of a LaNi5 phase, a LaNi3 phase, and a minor La2Ni7 phase;in addition, in the case of Cu-substitution, the Nd2Ni7 phase appears and the LaNi3 phase vanishes. Ther-modynamic tests show that the enthalpy change in the dehydriding process decreases, indicating that hydride stability decreases with in-creasing stoichiometry and increasing Cu content. The maximum discharge capacity, kinetic properties, and cycling stability of the alloy electrodes all increase and then decrease with increasing stoichiometry or increasing Cu content. Furthermore, Cu substitution for Co ame-liorates the discharge capacity, kinetics, and cycling stability of the alloy electrodes.
基金supported by the High-Tech Research and Development Program of China (No. 2007AA05Z117)the National Natural Science Foundation of China (Nos. 50971112 and 51001043)+1 种基金the China Post-doctoral Science Foundation Funded Project (20100470990)the Natural Science Foundation of Hebei Province, China (No. E2010001170)
文摘The phase structure and hydrogen storage properties of LaMg 3.70 Ni 1.18 alloy were investigated. The LaMg 3.70 Ni 1.18 alloy consists of main LaMg 2 Ni phase, minor La 2 Mg 17 and LaMg 3 phases. The alloy can be activated in the first hydriding/dehydriding process, and initial LaMg 2 Ni, La 2 Mg 17 , and LaMg 3 phases transfer to LaH 2.34 , Mg, and Mg 2 Ni phases after activation. The reversible hydrogen storage capacity of the LaMg 3.70 Ni 1.18 alloy is 2.47 wt.% at 558 K, which is higher than that of the LaMg 2 Ni alloy. The pressure-composition-temperature (PCT) curves display two hydriding plateaus, corresponding to the formation of MgH 2 and Mg 2 NiH 4 . However, only one dehydriding plateau is observed, owing to the synergetic effect of hydrogen desorption between MgH 2 and Mg 2 NiH 4 . The uptake time for hydrogen content to reach 99% of saturated state is less than 250 s, and 90% hydrogen can be released in 1200 s in the experimental conditions, showing fast kinetics in hydriding and dehydriding. The activation energies of the LaMg 3.70 Ni 1.18 alloy are –51.5 ± 1.1 kJ/mol and –57.0 ± 0.6 kJ/mol for hydriding and dehydriding, respectively. The hydriding/dehydriding kinetics of the LaMg 3.70 Ni 1.18 alloy is better than that of the Mg 2 Ni alloy, owing to the lower activation energy values.
基金This work was financially supported by National Natural Science Foundations of China (No.50131040)Key Technologies R & D Program of Inner Mongolia (No.20050205)College Scientific Research Project of Inner Mongolia (No.NJ05064).
文摘In order to improve the cycle stability of La-Mg-Ni-Co type alloy electrode, rapid quenching technology was employed. The effects of rapid quenching on the microstructure and cycle stability of the alloy were investigated. The obtained results show that the La2Mg(Ni0.85Co0.15)9M0.1 (M=B, Cr) alloy electrodes are composed of (La, Mg)Ni3 phase, LaNi5 phase and a small amount of the LaNi2 phase. A trace of the Ni2B phase exists in the as-cast MB alloy, and the Ni2B phase in the alloy nearly disappears after rapid quenching. Rapid quenching technology can slightly improve the cycling life of the alloy. When the quenching rate increases from 0 m·s-1 (As-cast is defined as quenching rate of 0 m·s-1) to 30 m·s-1, the cycle lives of the MB, MCr alloys enhance from 86 and 87 cycles to 106 and 119 cycles, respectively. On the other hand, the average capacity decay rates of the MB, MCr alloys decrease from 1.7172 and 1.7178 mAh·g-1·cycle-1 to 1.5751 and 1.3060 mAh·g-1·cycle-1 after 86 charge-discharges cycling, respectively.
基金the National Advanced Materials Committee of China andthe National Natural Science Foundation of China(Grunt NO.5
文摘The crystal structure, phase abundance and the electrochemical properties of Zr(Mn1-x Nix)2 (0.40 ≤x≤0.75) alloys were investigated by means of XRD, Rietveld refinement method and electrochemical measurements. The alloys are multiphase. C15 Laves phase occurs as a main phase accompanying with C14 phase and other minor phases, indicating that Ni element is C15-stabilized element for ZrMn2 alloy. The phase abundance and lattice parameters of Laves phase are influenced significantly by Ni substitution. The Zr(Mn0.45 Ni0.55)2 alloy with the highest amount of C15 phase exhibits the maximum electrochemical capacity of 242m Ah/g. C14 phase occurring in Zr-Mn-Ni alloys is beneficial for the electrochemical kinetics of hydride electrodes.
基金financially supported by the National Natural Science Foundation of China(31771773 and 31971931)the National Key Research and Development Program of China(2016YFD0100502)。
文摘The content and composition of wheat storage proteins are the major determinants of dough rheological properties and breadmaking quality and are influenced by cultivation conditions.This study aimed to investigate the effects of water deficit and high N-fertilizer application on wheat storage protein synthesis,gluten secondary structure,and breadmaking quality.Reverse-phase ultrahigh-performance liquid chromatography analysis showed that storage protein and gluten macropolymer accumulation was promoted under both independent applications and a combination of water-deficit and high N-fertilizer treatments.Fourier-transform infrared spectroscopy showed that water deficit and high N-fertilizer treatments generally improved protein secondary structure formation and lipid accumulation,and reduced flour moisture.In particular,high N-fertilizer application increasedβ-sheet content by 10.4%and the combination of water-deficit and high N-fertilizer treatments increased random coil content by 7.6%.These changes in gluten content and secondary structure led to improved dough rheological properties and breadmaking quality,including superior loaf internal structure,volume,and score.Our results demonstrate that moderately high N-fertilizer application under drought conditions can improve gluten accumulation,gluten secondary structure formation,and baking quality.
基金[This project was supported by the National Natural Science Foundation of China (No. 20373016), the Key Project of In-ternational Science and Technology Cooperation of MOST of China (No. 2005DFA60580), the Key Project of Guangdong Province (No. 2005B50101003), and the Excellent Young Teachers Program of MOE of China.]
文摘The stoichiometric alloy MlB5.0 and the hypo-stoichiometric alloy MlB4.85 were prepared by twin-roller rapid quenching process, and their structure and electrochemical properties were studied. The results of XRD show that both of the alloys have a typical single-phase hexagonal CaCus-type structure. The cell volume of the hylpo-stoichiometric alloy M1B4.85 is slightly larger than that of the stoichiometric alloy M1B5.0, although its lattice constant cla is smaller. Under 2 C discharging rate, i.e. 640 mA/g, the M1B4.85 has a discharge capacity of 320 mAh/g, which is higher than that of the M1Bs.o, 312 mAh/g. Nevertheless, the capacities of the M1B4.85 and the M1Bs.o decline 24.7% and 20.2% after 400 cycles, respectively. The relationship of electrochemical performances of the alloys with their structures is discussed.
基金Project Supported bythe Talents Development Foundation of Inner Mongolia Autonomous Region (200608)
文摘Mm0.3Ml0.7Ni3.55Co0.75Mn0.4-Al0.3 alloy has high chemical activity and favorable plateaus pressure. Mg2Ni is in favor of high hydrogen storage capacity and low weight, but it is difficult to be activated. In order to improve the capacity and cycle performances of hydrogen-storage alloy electrodes, Mm0.3Ml0.7Ni3.55Co0.75Mn0.4-Al0.3-x%Mg2Ni(x=0, 5, 10, 30) composite hydrogen storage alloys prepared by two-step re-melting were investigated in this work. The influences of Mg2Ni content on the cycle stabilities were analyzed by electrochemical methods. It was observed by XRD that the main phase of all the alloys is LaNi5 and the crystal lattice parameters of LaNi5 are changed with the increasing of x value, i.e, a-axis and unit cell volume decrease and c-axis decreases nonlinearly. The c-axis of alloy with x=5 is larger than the others. With the increasing of x value, capacity retentions of the composite hydrogen storage alloys rise from 66.21% while x=0 to 82.04% while x=10, but the capacity retention of the composite alloy with 30% Mg2Ni declines because of its decreasing axial ratio. More over, the composite alloy with 5% Mg2Ni shows the best cycle stability and higher discharge capacity, and it is an appropriate candidate for battery materials.
基金the National Natural Science Foundation of China(Nos.51777115 and 81527901)the National Key Research and Development Program of China(Nos.2016YFC0105502 and 2016YFC0105900)Tsinghua University Intiative Scientifc Research Program and Major Achievements Transformation Project of Beijing’s College.
文摘The interfacial performance of implanted neural electrodes is crucial for stimulation safety and the recording quality of neuronal activity.This paper proposes a novel surface architecture and optimization strategy for the platinum–iridium(Pt–Ir)electrode to optimize electrochemical performance and wettability.A series of surface micro/nano structures were fabricated on Pt–Ir electrodes with different combinations of four adjustable laser-processing parameters.Subsequently,the electrodes were characterized by scanning electron microscopy,energy-dispersive X-ray spectroscopy,cyclic voltammetry,electrochemical impedance spectroscopy,and wetting behavior.The results show that electrode performance strongly depends on the surface morphology.Increasing scanning overlap along with moderate pulse energy and the right number of pulses leads to enriched surface micro/nano structures and improved electrode performance.It raises the maximum charge storage capacity to 128.2 mC/cm^(2) and the interface capacitance of electrodes to 3.0×10^(4)μF/cm^(2) for the geometric area,compared with 4.6 mC/cm^(2) and 443.1μF/cm2,respectively,for the smooth Pt–Ir electrode.The corresponding optimal results for the optically measured area are 111.8 mC/cm^(2) and 2.6×10^(4)μF/cm^(2),which indicate the contribution of fner structures to the ablation profle.The hierarchical structures formed by the femtosecond laser dramatically enhanced the wettability of the electrode interface,giving it superwicking properties.A wicking speed of approximately 80 mm/s was reached.Our optimization strategy,leading to superior performance of the superwicking Pt–Ir interface,is promising for use in new neural electrodes.
基金financially supported by the Natural Science Foundation of Hebei Province(Nos.E2019203414,E2020203081 and E2019203161)the National Natural Science Foundation of China(Nos.51701175 and 51971197)+1 种基金the Innovation Fund for the Graduate Students of Hebei Province(No.CXZZBS2020062)the Doctoral Fund of Yanshan University(No.BL19031)
文摘Rare earth-Mg-Ni-based alloys with superlattice structures are new generation negative electrode materials for the nickel metal hydride batteries.Among them,the novel AB_(4)-type superlattice structure alloy is supposed to have superior cycling stability and rate capability.Yet its preparation is hindered by the crucial requirement of temperature and the special composition which is close to the other superlattice structure.Here,we prepare rare earth-Mg-Ni-based alloy and study the phase transformation of alloys to make clear the formation of AB_(4)-type phase.It is found Pr_(5)Co_(19)-type phase is converted from Ce_(5)Co_(19)-type phase and shows good stability at higher temperature compared to the Ce_(5)Co_(19)-type phase in the range of 930-970℃.Afterwards,with further 5℃increasing,AB_(4)-type superlattice structure forms at a temperature of 975℃by consuming Pr_(5)Co_(19)-type phase.In contrast with A_(5)B_(19)-type alloy,AB_(4)-type alloy has superior rate capability owing to the dominant advantages of charge transfer and hydrogen diffusion.Besides,AB_(4)-type alloy shows long lifespan whose capacity retention rates are 89.2%at the 100;cycle and 82.8%at the 200;cycle,respectively.AB_(4)-type alloy delivers 1.53 wt.%hydrogen storage capacity at room temperature and exhibits higher plateau pressure than Pr_(5)Co_(19)-type alloy.The work provides novel AB_(4)-type alloy with preferable electrochemical performance as negative electrode material to inspire the development of nickel metal hydride batteries.
基金supported financially by the National Natural Science Foundation of China(Grant Nos.91961125 and 21905019)“Key Program for International S&T Cooperation Projects of China”from the Ministry of Science and Technology of China(Grant No.2018YFE0124600)+2 种基金“the Fundamental Research Funds for the Central Universities”(Grant No.2018JBZ107)the Chemistry and Chemical Engineering Guangdong Laboratory(Grant No.1932004)support from the“Excellent One Hundred”project of Beijing Jiaotong University。
文摘Up to now,three kinds of ion-storage mechanisms are summarized towards anode materials in lithium/sodium-ion batteries,but they have low capacity and poor cyclic performance.Therefore,it is necessary to develop a new approach to optimize ion storage.Herein,we report an adsorption/desorption storage route through engineering electronic structure of cation-deficient Ti_(1-x)O_(2)nanosheets.Ti_(1-x)O_(2)nanosheets indeed exhibit higher capacity(332.1 mA h g^(-1)vs.137.7 mA h g^(-1)for LIBs,195.7 mA h g^(-1)vs.111 mA h g^(-1)for SIBs),and more stable cyclic performance(296 mA h g^(-1)vs.99 mA h g^(-1)for LIBs,178.1 mA h g^(-1)vs.80.2 mA h g^(-1)for SIBs after 100 cycles)at 0.1 A g^(-1)than TiO_(2)nanosheets.Kinetics analysis and density functional theory(DFT)calculations reveal that electronic structures of vacancy within Ti_(1-x)O_(2) nanosheets encourage a novel adsorption-desorption storage route.These results highlight the benefits of the engineered electronic structures within electrode material and implement novel ion-storage mechanism towards broad energy storage applications.
文摘There was an obvious relationship between seed testa structure, storage material and resistance to A. flavus of peanut. Results showed that seed testa of peanut germplasm with high resistance (HR) to A. flavus infection had thicker wax layer, integrated and tight epidermis layer, regular vascular tissue range. However, the seed testa of peanut germplasm with high sensitivity (HS) to A. flavus had the reverse results, and results of those with medium resistance (MR) to A. flavus lay in between, but changes of testa thickness were not significant among different resistance kinds. Results also showed that some seed storage materials were closely related with resistance potential to A. flavus. It seemed that varieties with higher resistance to A. flavus had higher oleic acid and protein content, lower linoleic acid and fat content. Content of palm acid, total sugar and VE did not show positive relationship with the resistance to A. flavus.
基金financially supported by the National Natural Science Foundation of China(No.51933007,No.51673123 and No.22005346)the National Key R&D Program of China(No.2017YFE0111500)+1 种基金the State Key Laboratory of Polymer Materials Engineering(Grant No.:sklpme2020-1-02)Financial support provided by the Fundamental Research Funds for the Central Universities(No.YJ202118)。
文摘Rational architecture design has turned out to be an effective strategy in improving the electrochemical performance of electrode materials for batteries.However,an elaborate structure that could simultaneously endow active materials with promoted reaction reversibility,accelerated kinetic and restricted volume change still remains a huge challenge.Herein,a novel chemical interaction motivated structure design strategy has been proposed,and a chemically bonded Co(CO_(3))_(0.5)OH·0.11 H_(2)O@MXene(CoCH@MXene)layered-composite was fabricated for the first time.In such a composite,the chemical interaction between Co^(2+)and MXene drives the growth of smaller-sized CoCH crystals and the subsequent formation of interwoven CoCH wires sandwiched in-between MXene nanosheets.This unique layered structure not only encourages charge transfer for faster reaction dynamics,but buffers the volume change of CoCH during lithiation-delithiation process,owing to the confined crystal growth between conductive MXene layers with the help of chemical bonding.Besides,the sandwiched interwoven CoCH wires also prevent the stacking of MXene layers,further conducive to the electrochemical performance of the composite.As a result,the as-prepared CoCH@MXene anode demonstrates a high reversible capacity(903.1 mAh g^(-1)at 100 mA g^(-1))and excellent cycling stability(maintains 733.6 mAh g^(-1)at1000 mA g^(-1)after 500 cycles)for lithium ion batteries.This work highlights a novel concept of layerby-layer chemical interaction motivated architecture design for futuristic high performance electrode materials in energy storage systems.
文摘The rare earth based hydrogen storage alloys MmxM1 1 - x ( Ni3.55 Co0.75 Mn0.4 A10.3 ) ( x = 0 ~ 0.5 ) were investigated in this work.Adjusted Ml: Mm ratio to change the content of La,Ce,Pr and Nd in the alloys and then to change the phase structure, the influences of phase structure on the electrochemical properties were analyzed.The results indicate that the main phase of all alloys is LaNi5 with CaCu5 type structure and the crystal lattices constants of LaNi5 are changed with increasing x value, i.e, decreased a-axis, increased c-axis and axis ratio and nonlinear decreased crystal volume.The crystal volume of the alloy with x = 0.3 is larger than others.There is second phase A1LaNi4 in alloys when x≥0.3, which decrease the discharge capacity, but increase the cycling stability and high rate discharge ability.Compared comprehensively, the alloy with x = 0.3 shows the higher discharge capacity and the better cycling stability.
基金supported by the National Natural Science Foundation of China (No. 50772133)
文摘MgNi-based hydrogen storage alloys Mg1–xTixNi (x = 0, 0.1, 0.2, and 0.3) were prepared by means of mechanical alloying. Mg in the alloy was partially substituted by Ti to improve the cycle stability of the alloys. The effects of the substitution of Ti for Mg on the microstructure and electrochemical performances of the alloys were investigated in detail. The results indicate that the substitution of Ti for Mg obviously decreases the discharge capacity, but it significantly improves their cycle stabilities. The microstructure of the alloys analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM) shows that the alloys have a dominatingly amorphous structure. The substitution of Ti for Mg helps to improve the anti-oxidation/corrosion ability of the MgNi alloy but demolishes the electrochemical kinetics of hydrogenation/dehydrogenation. The Mg0.9Ti0.1Ni alloy electrode milled for 80 h exhibits the best integrative capability, which has the maximal discharge capacity of 331.66 mAh/g and the C30/Cmax of 63.65%.
文摘The phase structure and electrochemical characteristics of Ml ((Ni3.55Co0.75Mn0.40Al0.30)sx ( x = 0.88, 0.92, 0.96, 1.00) hydrogen storage alloys were studied. The effect of the stoichiometric ratio on the phase structure and electrochemical characteristics was analyzed. The results of XRD reveal that all the alloys consist mainly of LaNi5 phase with the hexagonal CaCu5 structure. But a few of the diffraction peaks of La2Ni7 phase on XRD pattern are observed when x ≤ 0.92, and with decreasing x, the intensity of La2Ni7 diffraction peaks increases and the values of lattice parameters a and cell volume increase, c and c/a of LaNi5 phase decrease gradually. When x≥0.96, La2Ni7 phase disappears and the alloys become single CaCu5-type. The electrochemical tests show that the maximum discharge capacity, high rate dischargeability and low temperature dischargeability are improved to different degrees by adjusting the stoichiometric ratio.
文摘Structure and electrochemical properties of (La, Ce, Pr, Nd)_2MgNi_9 hydrogen storage alloys were investigated through orthogonal design experiments, and the alloys were obtained through induction melting followed by annealing treatment. The structure of main phase in alloys belongs to PuNi_3-type with a space group R3m. Rare earth elements, as a substitute of lanthanum, have a significant effect on phase structure of alloys, elements of cerium and neodymium are beneficial to the formation of Gd_2Co_7-type phase with a space group P 6_3/mmc. Rare earth elements can decrease the unit cell volume of main phase of alloys dramatically, and increase the axis ratio. The results of electrochemical experiment showed that the discharge capacity of alloy electrodes ranged from 342.97 to 380.68 mAh·g -1, and elements of cerium and neodymium can reduce the discharge capacity of alloy electrodes significantly. Compared to the electrode of La_2MgNi_9 alloy, the substitution of lanthanum by rare earth elements did not improve the cyclic stability of alloy electrodes due to the anisotropic structure change of unit cell. While rare-earth elements can improve the high rate dischargeability of alloy electrodes, the high rate dischargeability of alloy electrodes could reach the maximum when the unit cell volume of PuNi_3-type structure was about 0532 nm.