The effects of the two-step ageing parameters （temperature and time） on the mechanical properties and electrical conductivity of 7B04 （A1-Zn-Mg-Cu） pre-stretched thick plates were studied. The results reveal that ...The effects of the two-step ageing parameters （temperature and time） on the mechanical properties and electrical conductivity of 7B04 （A1-Zn-Mg-Cu） pre-stretched thick plates were studied. The results reveal that the initial T1 ageing contributes a major increase of the tensile strength, and the 0.2% proof stress value reaches 482 MPa after ageing for 7 h at 115℃. Behavioral differences in the tensile properties of the alloy after the two-step ageing treatment were less with the first-step ageing at 115~C for different time periods （7, 14, and 21 h）. The effects of the second ageing parameters on the properties and microstructure of the 7B04 alloy were remarkable. TEM analysis of the samples aged at Temper I （7 h at 115℃ ＋ 12 h at 160℃） and Temper II （7 h at 115℃ ＋ 16 h at 165℃） indicates that two kinds of phases, i.e. 11＇ and 11 phases, precipitate from the matrix and efficiently improve the tensile strength of the alloy, and the grain boundary precipitates are coarse and discrete. There are obvious precipitate free zones （PFZs） along the grain boundary in the microstructure of the alloy after the two-step ageing treatment.展开更多
The tensile properties, electrical conductivity, and microstructure of the forged A1-7.1Zn-1.1Mg-1.6Cu-0.14Zr alloy were investigated after a two-step ageing treatment at 120 and 170℃. The results indicate that the s...The tensile properties, electrical conductivity, and microstructure of the forged A1-7.1Zn-1.1Mg-1.6Cu-0.14Zr alloy were investigated after a two-step ageing treatment at 120 and 170℃. The results indicate that the strength of the alloy reaches the peak value at 170~C for 1 h during the second step ageing and then decreases sharply. However, the electrical conductivity value increases continuously with the second ageing time increasing. The fracture mechanism of the alloy is intergranular fracture for 1 h and then changes to dimple transgranular fracture later, and the toughness of the alloy is improved significantly. The phases of rl＇ and 1＂1 are major precipitates in the alloy under the two-step ageing condition. Discontinuous grain boundary precipitates and precipitate-flee zones along the grain boundary are clearly observed.展开更多
Background Depression,anxiety and schizophrenia among older persons have become global public health challenges.However,the burden of these disorders in ageing and aged countries has not been analysed.Aims To investig...Background Depression,anxiety and schizophrenia among older persons have become global public health challenges.However,the burden of these disorders in ageing and aged countries has not been analysed.Aims To investigate the burden of depression,anxiety and schizophrenia among older adults in ageing and aged countries.Methods Using data from the Global Burden of Disease Study 2019,we calculated the estimated annual percentage change(EAPC)in the age-standardised incidence rates(ASiR)and age-standardised disability-adjusted life years(DALYs)rates(ASDR)for depression,anxiety and schizophrenia of older people in ageing countries(China,India,Indonesia)and aged countries(Japan,Italy,Portugal)between 1990 and 2019.Trends in incidence and DALYs were analysed by gender and age.Results In 2019,the highest incidence of depression,anxiety and schizophrenia in the older population in aged countries was in Japan(927271.3(752552.3-1125796.5),51498.2(37625.7-70487.3)and 126.0(61.0-223.2),respectively),while the highest incidence in ageing countries was in China(5797556.9(4599403.4-7133006.5),330256.1(246448.9-445987.4)and 1067.7(556.2-1775.9),respectively).DALYs for these disorders were similar,with the highest in Japan and China.From 1990 to 2019,the ASIR for depressive disorders decreased in aged countries but increased in ageing countries;the ASIR for anxiety disorders and schizophrenia declined in both ageing and aged countries.The ASDR for depressive disorders was consistent with the ASIR but not for anxiety disorders and schizophrenia.The ASIR for depressive disorders was higher in older women,while the opposite was observed in anxiety disorders and schizophrenia.Notably,the conditions of burden of depressive disorders,anxiety disorders and schizophrenia in the 65-70-year-old age group were the most burdensome.Conclusions The incidence and DALYs of these three mental disorders increased while exhibiting differences between ageing and aged countries.Raising awareness about formulating health policies for preventing and treating mental disorders in the older population is necessary to reduce the future burden posed by the ageing challenge.展开更多
Multiplicative noise removal problems have attracted much attention in recent years.Unlike additive noise,multiplicative noise destroys almost all information of the original image,especially for texture images.Motiva...Multiplicative noise removal problems have attracted much attention in recent years.Unlike additive noise,multiplicative noise destroys almost all information of the original image,especially for texture images.Motivated by the TV-Stokes model,we propose a new two-step variational model to denoise the texture images corrupted by multiplicative noise with a good geometry explanation in this paper.In the first step,we convert the multiplicative denoising problem into an additive one by the logarithm transform and propagate the isophote directions in the tangential field smoothing.Once the isophote directions are constructed,an image is restored to fit the constructed directions in the second step.The existence and uniqueness of the solution to the variational problems are proved.In these two steps,we use the gradient descent method and construct finite difference schemes to solve the problems.Especially,the augmented Lagrangian method and the fast Fourier transform are adopted to accelerate the calculation.Experimental results show that the proposed model can remove the multiplicative noise efficiently and protect the texture well.展开更多
The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formabilit...The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formability of Al-Cu-Li alloy is vital.A thorough comparison of the effects of cryo-deformation and ambient temperature large pre-deformation(LPD)on the creep ageing response in the 2195 alloy sheet at 160℃with different stresses has been made.The evolution of dislocations and precipitates during creep ageing of LPD alloys are revealed by X-ray diffraction and transmission electron microscopy.High-quality 2195 alloy sheet largely pre-deformed by 80%without edge-cracking is obtained by cryo-rolling at liquid nitrogen temperature,while severe edge-cracking occurs during room temperature rolling.The creep formability and strength of the 2195 alloy are both enhanced by introducing pre-existing dislocations with a density over 1.4×10^(15)m^(−2).At 160℃and 150 MPa,creep strain and creep-aged strength generally increases by 4−6 times and 30−50 MPa in the LPD sample,respectively,compared to conventional T3 alloy counterpart.The elongation of creep-aged LPD sample is low but remains relevant for application.The high-density dislocations,though existing in the form of dislocation tangles,promote the formation of refined T1 precipitates with a uniform dispersion.展开更多
The safety and reliability of weapon systems would be significantly affected by changes in the performance of energetic materials due to ambient temperature and humidity.Nanothermites have promising applications due t...The safety and reliability of weapon systems would be significantly affected by changes in the performance of energetic materials due to ambient temperature and humidity.Nanothermites have promising applications due to their excellent reactivity.Therefore it becomes extremely important to understand their aging and failure process in the environment before using them.Here,the aging and failure process of Al/CuO in 71°C/60%RH were investigated,and showed that CuO nanoparticles negatively catalyze Al nanopowders,resulting in rapid hydration.The anti-aging effect of FAS-17-coated Al nanopowder was also examined.The aging process of Al,Al/CuO,and Al@FAS-17/CuO in high humidity and heat environment were revealed by quasi-in situ SEM and TEM methods.Compared with the aging of pure Al,the Al nanopowder in the nanothermites strongly agglomerated with the CuO nanopowder and hydrated earlier.This may be caused by CuO catalyzed hydration of Al nanopowder.The energy release experiments showed that the performance of Al/CuO decreased rapidly and failed to ignite after 4 h of aging.In contrast,the Al@FAS-17/CuO thermite can achieve long-term stability of up to 60 h in the same environment by simple cladding of FAS-17.It is found that FAS-17 coated Al nanopowder can prevent both particle agglomeration and water erosion,which is an effective means to make nanothermites application in high humidity and heat environment.展开更多
This research considered the effect of non-natural aging on the microstructural characteristics and mechanical properties of as-cast aluminum 6063 alloys. The samples were developed through a sand casting process and ...This research considered the effect of non-natural aging on the microstructural characteristics and mechanical properties of as-cast aluminum 6063 alloys. The samples were developed through a sand casting process and machined into tensile and impact test samples before carrying out solution heat treatment at 550?C (0.83 T<sub>m</sub>) on two parts of the samples while retaining one part as the control. The two parts were further divided into sets denoted A and B and were aged at 180?C (0.27 T<sub>m</sub>) and 160?C (0.24 T<sub>m</sub>), respectively, for 12 hours. The results showed that sample A has the optimal yield strength and ultimate tensile strength of 192 and 206 MPa, respectively. Likewise, the sample gave the highest impact strength value of about 9.63 J/mm<sup>2</sup>. The observed results were supported by the optical micrograph, which revealed that the sample has evenly dispersed precipitates in its microstructure. This is deemed responsible for the observed increase in strength of the sample.展开更多
基金the National High-Tech Research Development Program of China (No. 2003AA331100).
文摘The effects of the two-step ageing parameters （temperature and time） on the mechanical properties and electrical conductivity of 7B04 （A1-Zn-Mg-Cu） pre-stretched thick plates were studied. The results reveal that the initial T1 ageing contributes a major increase of the tensile strength, and the 0.2% proof stress value reaches 482 MPa after ageing for 7 h at 115℃. Behavioral differences in the tensile properties of the alloy after the two-step ageing treatment were less with the first-step ageing at 115~C for different time periods （7, 14, and 21 h）. The effects of the second ageing parameters on the properties and microstructure of the 7B04 alloy were remarkable. TEM analysis of the samples aged at Temper I （7 h at 115℃ ＋ 12 h at 160℃） and Temper II （7 h at 115℃ ＋ 16 h at 165℃） indicates that two kinds of phases, i.e. 11＇ and 11 phases, precipitate from the matrix and efficiently improve the tensile strength of the alloy, and the grain boundary precipitates are coarse and discrete. There are obvious precipitate free zones （PFZs） along the grain boundary in the microstructure of the alloy after the two-step ageing treatment.
基金supported by the Sub-project of Major State Basic Research Development Program of China (No 2005CB623705)the National Natural Science Foundation of China (No 50875031)
文摘The tensile properties, electrical conductivity, and microstructure of the forged A1-7.1Zn-1.1Mg-1.6Cu-0.14Zr alloy were investigated after a two-step ageing treatment at 120 and 170℃. The results indicate that the strength of the alloy reaches the peak value at 170~C for 1 h during the second step ageing and then decreases sharply. However, the electrical conductivity value increases continuously with the second ageing time increasing. The fracture mechanism of the alloy is intergranular fracture for 1 h and then changes to dimple transgranular fracture later, and the toughness of the alloy is improved significantly. The phases of rl＇ and 1＂1 are major precipitates in the alloy under the two-step ageing condition. Discontinuous grain boundary precipitates and precipitate-flee zones along the grain boundary are clearly observed.
基金Shanghai'Science and Technology Innovation Action Plan'medical innovation research(21Y11905600)Shanghai'Science and Technology Innovation Action Plan'Natural Science Foundation of Shanghai(21ZR1455100)+1 种基金the National Natural Science Foundation of China(81701344)the Shanghai Mental Health Center General Projects(2021-YJ-02).
文摘Background Depression,anxiety and schizophrenia among older persons have become global public health challenges.However,the burden of these disorders in ageing and aged countries has not been analysed.Aims To investigate the burden of depression,anxiety and schizophrenia among older adults in ageing and aged countries.Methods Using data from the Global Burden of Disease Study 2019,we calculated the estimated annual percentage change(EAPC)in the age-standardised incidence rates(ASiR)and age-standardised disability-adjusted life years(DALYs)rates(ASDR)for depression,anxiety and schizophrenia of older people in ageing countries(China,India,Indonesia)and aged countries(Japan,Italy,Portugal)between 1990 and 2019.Trends in incidence and DALYs were analysed by gender and age.Results In 2019,the highest incidence of depression,anxiety and schizophrenia in the older population in aged countries was in Japan(927271.3(752552.3-1125796.5),51498.2(37625.7-70487.3)and 126.0(61.0-223.2),respectively),while the highest incidence in ageing countries was in China(5797556.9(4599403.4-7133006.5),330256.1(246448.9-445987.4)and 1067.7(556.2-1775.9),respectively).DALYs for these disorders were similar,with the highest in Japan and China.From 1990 to 2019,the ASIR for depressive disorders decreased in aged countries but increased in ageing countries;the ASIR for anxiety disorders and schizophrenia declined in both ageing and aged countries.The ASDR for depressive disorders was consistent with the ASIR but not for anxiety disorders and schizophrenia.The ASIR for depressive disorders was higher in older women,while the opposite was observed in anxiety disorders and schizophrenia.Notably,the conditions of burden of depressive disorders,anxiety disorders and schizophrenia in the 65-70-year-old age group were the most burdensome.Conclusions The incidence and DALYs of these three mental disorders increased while exhibiting differences between ageing and aged countries.Raising awareness about formulating health policies for preventing and treating mental disorders in the older population is necessary to reduce the future burden posed by the ageing challenge.
文摘Multiplicative noise removal problems have attracted much attention in recent years.Unlike additive noise,multiplicative noise destroys almost all information of the original image,especially for texture images.Motivated by the TV-Stokes model,we propose a new two-step variational model to denoise the texture images corrupted by multiplicative noise with a good geometry explanation in this paper.In the first step,we convert the multiplicative denoising problem into an additive one by the logarithm transform and propagate the isophote directions in the tangential field smoothing.Once the isophote directions are constructed,an image is restored to fit the constructed directions in the second step.The existence and uniqueness of the solution to the variational problems are proved.In these two steps,we use the gradient descent method and construct finite difference schemes to solve the problems.Especially,the augmented Lagrangian method and the fast Fourier transform are adopted to accelerate the calculation.Experimental results show that the proposed model can remove the multiplicative noise efficiently and protect the texture well.
基金Projects(52274404,52305441,U22A20190)supported by the National Natural Science Foundation of ChinaProjects(2022JJ20065,2023JJ40739)supported by the Natural Science Foundation of Hunan Province,China+2 种基金Project(2022RC1001)supported by the Science and Technology Innovation Program of Hunan Province,ChinaProject(2023ZZTS0972)supported by the Fundamental Research Funds for the Central Universities,ChinaProject(2021YFB3400903)supported by the National Key R&D Program of China。
文摘The creep strain of conventionally treated 2195 alloy is very low,increasing the difficulty of manufacturing Al-Cu-Li alloy sheet parts by creep age forming.Therefore,finding a solution to improve the creep formability of Al-Cu-Li alloy is vital.A thorough comparison of the effects of cryo-deformation and ambient temperature large pre-deformation(LPD)on the creep ageing response in the 2195 alloy sheet at 160℃with different stresses has been made.The evolution of dislocations and precipitates during creep ageing of LPD alloys are revealed by X-ray diffraction and transmission electron microscopy.High-quality 2195 alloy sheet largely pre-deformed by 80%without edge-cracking is obtained by cryo-rolling at liquid nitrogen temperature,while severe edge-cracking occurs during room temperature rolling.The creep formability and strength of the 2195 alloy are both enhanced by introducing pre-existing dislocations with a density over 1.4×10^(15)m^(−2).At 160℃and 150 MPa,creep strain and creep-aged strength generally increases by 4−6 times and 30−50 MPa in the LPD sample,respectively,compared to conventional T3 alloy counterpart.The elongation of creep-aged LPD sample is low but remains relevant for application.The high-density dislocations,though existing in the form of dislocation tangles,promote the formation of refined T1 precipitates with a uniform dispersion.
基金supported by the National Natural Science Foundation of China(Grant No.22275092)。
文摘The safety and reliability of weapon systems would be significantly affected by changes in the performance of energetic materials due to ambient temperature and humidity.Nanothermites have promising applications due to their excellent reactivity.Therefore it becomes extremely important to understand their aging and failure process in the environment before using them.Here,the aging and failure process of Al/CuO in 71°C/60%RH were investigated,and showed that CuO nanoparticles negatively catalyze Al nanopowders,resulting in rapid hydration.The anti-aging effect of FAS-17-coated Al nanopowder was also examined.The aging process of Al,Al/CuO,and Al@FAS-17/CuO in high humidity and heat environment were revealed by quasi-in situ SEM and TEM methods.Compared with the aging of pure Al,the Al nanopowder in the nanothermites strongly agglomerated with the CuO nanopowder and hydrated earlier.This may be caused by CuO catalyzed hydration of Al nanopowder.The energy release experiments showed that the performance of Al/CuO decreased rapidly and failed to ignite after 4 h of aging.In contrast,the Al@FAS-17/CuO thermite can achieve long-term stability of up to 60 h in the same environment by simple cladding of FAS-17.It is found that FAS-17 coated Al nanopowder can prevent both particle agglomeration and water erosion,which is an effective means to make nanothermites application in high humidity and heat environment.
文摘This research considered the effect of non-natural aging on the microstructural characteristics and mechanical properties of as-cast aluminum 6063 alloys. The samples were developed through a sand casting process and machined into tensile and impact test samples before carrying out solution heat treatment at 550?C (0.83 T<sub>m</sub>) on two parts of the samples while retaining one part as the control. The two parts were further divided into sets denoted A and B and were aged at 180?C (0.27 T<sub>m</sub>) and 160?C (0.24 T<sub>m</sub>), respectively, for 12 hours. The results showed that sample A has the optimal yield strength and ultimate tensile strength of 192 and 206 MPa, respectively. Likewise, the sample gave the highest impact strength value of about 9.63 J/mm<sup>2</sup>. The observed results were supported by the optical micrograph, which revealed that the sample has evenly dispersed precipitates in its microstructure. This is deemed responsible for the observed increase in strength of the sample.
