Life-Cycle Bearing Capacity for Pre-Stressed T-beams Based on Full-Scale Destructive Test

To investigate the evolution of load-bearing characteristics of pre-stressed beams throughout their service life and to provide a basis for accurately assessing the actual working state of damaged pre-stressed concrete T-beams,destructive tests were conducted on full-scale pre-stressed concrete beams.Based on the measurement and ana-lysis of beam deflection,strain,and crack development under various loading levels during the research tests,combined with the verification coefficient indicators specified in the codes,the verification coefficients of bridges at different stages of damage can be examined.The results indicate that the T-beams experience complete,incom-plete linear,and non-linear stages during the destructive test process.In the complete linear elastic stage,both the deflection and bottom strain verification coefficients comply with the specifications,indicating a good structural load-bearing capacity no longer adheres to the code’s requirements.In the non-linear stage,both coefficients exhi-bit a sharp increase,resulting in a further decrease in the structure’s load-bearing capacity.According to the pro-visions of the current code,the beam can be in the incomplete linear stage when both values fall within the code’s specified range.The strain verification coefficient sourced from the compression zone at the bottom of theflange is not recommended for assessing the bridge’s load-bearing capacity.

Experimental research on ultimate bearing capacity of N-joints of grouted square steel tube trusses

Cave-in failure is apt to occur in joints of trusses made of square hollow sections. In order to turn the failure mode into a strength failure mode of joint members, the idea is proposed that the chord of the truss is grouted to increase the cave-in beating capacity of a hollow tube chord. An experiment of eight specimens of N- joints made of grout-filled square steel tubes is performed. Based on the experimental study, the geometrical parameters of specimens are analyzed, and the effects of the confinement index ε, the spacing between the two web members g and the ratio of side length of the vertical web member to that of the chord β on the behavior of specimens are investigated through simulation analysis by simulation analyses, the mechanical properties and the failure an ANSYS program. Based on the test results and modes of this kind of joints are analyzed and the formulae to predict the ultimate bearing capacities corresponding to different failure modes are developed. The ultimate bearing capacity of compressive N-joints is calculated in accordance with the cave-in failure mode of a chord member; the ultimate bearing capacity of tension N-joints is calculated in accordance with the punchingshear failure mode; the ultimate bearing capacity of a chord member is calculated in accordance with the shear failure mode in normal sections.

Construction of improved rigid blocks failure mechanism for ultimate bearing capacity calculation based on slip-line field theory

Based on the slip-line field theory, a two-dimensional slip failure mechanism with mesh-like rigid block system was constructed to analyze the ultimate bearing capacity problems of rough foundation within the framework of the upper bound limit analysis theorem. In the velocity discontinuities in transition area, the velocity changes in radial and tangent directions are allowed. The objective functions of the stability problems of geotechnical structures are obtained by equating the work rate of external force to internal dissipation along the velocity discontinuities, and then the objective functions are transformed as an upper-bound mathematic optimization model. The upper bound solutions for the objective functions are obtained by use of the nonlinear sequential quadratic programming and interior point method. From the numerical results and comparative analysis, it can be seen that the method presented in this work gives better calculation results than existing upper bound methods and can be used to establish the more accurate plastic collapse load for the ultimate bearing capacity of rough foundation.

New design equations for estimation of ultimate bearing capacity of shallow foundations resting on rock masses

Rock masses are commonly used as the underlying layer of important structures such as bridges, dams and transportation constructions. The success of a foundation design for such structures mainly depends on the accuracy of estimating the bearing capacity of rock beneath them. Several traditional numerical approaches are proposed for the estimation of the bearing capacity of foundations resting on rock masses to avoid performing elaborate and expensive experimental studies. Despite this fact, there still exists a serious need to develop more robust predictive models. This paper proposes new nonlinear prediction models for the ultimate bearing capacity of shallow foundations resting on non-fractured rock masses using a novel evolutionary computational approach, called linear genetic programming. A comprehensive set of rock socket, centrifuge rock socket, plate load and large-scaled footing load test results is used to develop the models. In order to verify the validity of the models, the sensitivity analysis is conducted and discussed. The results indicate that the proposed models accurately characterize the bearing capacity of shallow foundations. The correlation coefficients between the experimental and predicted bearing capacity values are equal to 0.95 and 0.96 for the best LGP models. Moreover, the derived models reach a notably better prediction performance than the traditional equations.

Analysis of the Ultimate Bearing Capacity of Oil Field Drilling Masts

In order to improve the safety of drilling operations, this paper presents a new method for forecasting the ultimate bearing capacity of oil field drilling masts. The method is based on a double nonlinear finite element theory and applies a referential stress method for measuring defects and defacements. The lab mast model was analyzed using the proposed method. The relative error, which was less than 5.0% between the forecast results and the destructive experiment values,verified the correctness of this method. It also forecasts the ultimate bearing capacity for a local drilling mast.

Influence of the Spudcan Angle on the Ultimate Bearing Capacity of Jack-up Platform

Jack-up platforms of the Ocean engineering structures always withstand the vertical gravity loads which are applied to the seabed by spudcan, so it is important to determine the bearing capacity and the penetration depth of the spudcan for its geometry. In fact, it is up to the deformation law and the failure modes of soil surrounding the spudcan which can calculate the ultimate bearing capacity of the spudcan foundation on the soil seabed. By using the finite element analysis software Abaqus, the deformation law of soil around the spudcan is analyzed in detail, and the failure modes of soil surrounding the spudcan foundation are achieved. At the same time, based on the limit equilibrium theory, by use of static permissible slip-line field, the ultimate bearing capacity of the spudcan foundation is analyzed and the lower limit solution is derived theoretically, and the effect of the spudcan angle on the ultimate bearing capacity is investigated. The numerical results are compared with those obtained by the theoretical formulas deduced in this paper. On the basis of the lower limit solutions in this paper, the effect of the spudcan angle on the ultimate bearing capacity is revealed, and a practical bearing capacity formula is given to take the effect of the spudcan angle into consideration.

Probabilistic analysis of ultimate seismic bearing capacity of strip foundations

This paper presents a reliability analysis of the pseudo-static seismic bearing capacity of a strip foundation using the limit equilibrium theory. The first-order reliability method(FORM) is employed to calculate the reliability index. The response surface methodology(RSM) is used to assess the Hasofer e Lind reliability index and then it is optimized using a genetic algorithm(GA). The random variables used are the soil shear strength parameters and the seismic coefficients(khand kv). Two assumptions(normal and non-normal distribution) are used for the random variables. The assumption of uncorrelated variables was found to be conservative in comparison to that of negatively correlated soil shear strength parameters. The assumption of non-normal distribution for the random variables can induce a negative effect on the reliability index of the practical range of the seismic bearing capacity.

Experimental research on ultimate bearing capacity of grouted-round-steel-tube N-joint

As an important structural member in self-supporting concrete floor during construction,encased steel truss-concrete composite beam has brilliant prospect in outer-jacketing structures for adding stories or mega frame structures.Compared with encased angle truss,encased round steel tube truss can facilitate layout of itself in column and facilitate layout and anchorage of prestressed reinforcement placed horizontally.N-joint is wildly used in encased steel truss.For cave-in failure easily occurs in hollow steel-tube joint,the idea that the chord is grouted to increase cave-in bearing capacity of hollow tube is proposed.Test results of 8 grouted-round-steel-tube N-joints from the beginning of loading to failure are reported.Mechanical property and failure mode of this kind of truss joint are analyzed,and the formulas of ultimate bearing capacity of the joint corresponding to different failure modes are established.All these can provide basic data for spreading encased steel truss-concrete composite beam.

Determination of ultimate bearing capacity of uplift piles using intact and non-intact load−displacement curve

Based on the field destructive test of six rock-socketed piles with shallow overburden,three prediction models are used to quantitatively analyze and predict the intact load−displacement curve.The predicted values of ultimate uplift capacity were further determined by four methods(displacement controlling method(DCM),reduction coefficient method(RCM),maximum curvature method(MCM),and critical stiffness method(CSM))and compared with the measured value.Through the analysis of the relationship between the change rate of pullout stiffness and displacement,a method used to determine the ultimate uplift capacity via non-intact load−displacement curve was proposed.The results show that the predicted value determined by DCM is more conservative,while the predicted value determined by MCM is larger than the measured value.This suggests that RCM and CSM in engineering applications can be preferentially applied.Moreover,the development law of the change rate of pullout stiffness with displacement agrees well with the attenuation form of power function.The theoretical predicted results of ultimate uplift capacity based on the change rate of pullout stiffness will not be affected by the integrity of the curve.The method is simple and applicable for the piles that are not loaded to failure state,and thus provides new insights into ultimate uplift capacity determination of test piles.

Seismic ultimate bearing capacity of strip footings on slope

The influence of earthquake forces on ultimate bearing capacity of foundations on sloping ground was studied. A solution to seismic ultimate bearing capacity of strip footings on slope was obtained by utilizing pseudo-static analysis method and taking the effect of intermediate principal stress into consideration. Based on limit equilibrium theory, the formulae for computing static bearing capacity factors, Nq, Nc, Nγ, and dynamic bearing capacity factors, Nqd, Ned, Nγd, which are associated with surcharge, cohesion and self-weight of soils respectively, were presented. A great number of analysis calculations were carried out to obtain the relationship curves of the static and dynamic bearing capacity factors versus various calculation parameters. The curves can serve as the practical engineering design. The calculation results also show that when the values of horizontal and vertical seismic coefficients are 0.2, the dynamic bearing capacity factors Nqd, Ned and Nγd, in which the effects of intermediate principal stress are taken into consideration, increase by 4%-42%, 3%-27% and 34%-57%, respectively.

Upper Bound Solutions for Uplift Ultimate Bearing Capacity of Suction Caisson Foundation

Suction caisson foundation derives most of their uplift resistance from passive suction developed during the pullout movement. It was observed that the passive suction generated in soil at the bottom of the caisson and the failure mode of suction caisson foundation subjecting pullout loading behaves as a reverse compression failure mechanism.The upper bound theorems have been proved to be a powerful method to find the critical failure mechanism and critical load associated with foundations, buried caissons and other geotechnical structures. However, limited attempts have been reported to estimate the uplift bearing capacity of the suction caisson foundation using the upper bound solution. In this paper, both reverse failure mechanisms from Prandtl and Hill were adopted as the failure mechanisms for the computation of the uplift bearing capacity of the suction caisson. New equations were proposed based on both failure mechanisms to estimate the pullout capacity of the suction caisson. The proposed equations were verified by the test results and experimental data from published literature. And the two solutions agree reasonably well with the other test results. It can be proved that both failure mechanisms are reasonably and more consistent with the actual force condition.

Stability Analysis of Space Compcoite Structore and Its Ultimate Bearing Capacity

In this paper, using incremental equilibrium equation, the authors have studiedthe effeet of ultimate bearing capacity of every component on structuralstability, and discussed the stability analysis method for space compositestructures. With the help of the test results for the concrete filled ateel tubeskeleton of the long-spen RC arch bridse, it is proved that the proposed methodis accurate and reliable.

3D FE Analysis of Effect of Ground Subsidence and Piled Spacing on Ultimate Bearing Capacity of Piled Raft and Axial Force of Piles in Piled Raft

The effects of ground subsidence and piled spacing on axial force of piles in squared piled rafts were investigated using numerical analysis. Two cases of piled rafts in soft clay including case 1 (s = 2d) and case 2 (s = 4d) with s and d were piled spacing and piled diameter respectively were considered in this study. Undrained (without ground water pumping) and drained (with ground water pumping) conditions were applied in each case in order to evaluate variations of ultimate bearing capacity of piled raft and axial force of the piles in piled raft. The results showed that ultimate bearing capacity increased about 25% for undrained condition and about 32% for drained condition when piled spacing increased from 2d to 4d. In the same piled spacing, axial force of the piles increased about 9% for piled spacing of 2d and 7% for piled spacing of 4d when drained condition was applied. When piled spacing increased 2 times (2d to 4d), the axial force of piles increased about 7% for undrained condition and about 5% for drained condition.

ULTIMATE LOAD-BEARING CAPACITY OF CYLINDER DERIVED FROM AUTOFRETTAGE UNDER IDEAL CONDITION

According to the basic theory on autofrettage and according to the 4th strength theory, several parameters and their relations are studied under ideal condition, including σej/σy, the equivalent stress of total stresses at elastoplastic juncture; σei/σy, the equivalent stress of total stresses at inside surface; σej＇/σy, the equivalent stress of residual stresses at elastoplastic juncture; σei＇/σy, the equivalent stress of residual stresses at inside surface; and p/σy, load-bearing capacity of an autofrettaged cylinder. By theoretical study on relations between the parameters, noticeable results and laws are achieved： to satisfy ｜σei＇｜=σy. the relation between kj and k is, k^2lnkj^2-k^2-kj^2＋2=0, when k→∞, kj = √e = 1.648 72, as based on the 3rd strength theory, where k is the outside/inside radius ratio of a cylinder, kj is the ratio of elastoplastic juncture radius to inside radius of a cylinder; If the plastic region covers the whole wall of a cylinder, for compressive yield not to occur after removing autofrettage pressure, the ultimate k is k=-2.218 46 as based on the 3rd strength theory; With k=2.218 46, a cylinder＇s ultimate load-bearing capacity equals its entire yield pressure, or p/σy=21nk/√3; The maximum and optimum load-bearing capacity of an autofrettaged cylinder is just 2 times the loading which an unautofrettaged cylinder can bear elastically, or p/σy=2（k^2-1）/√3 k^2, and the limit of the load-bearing capacity of an autofrettaged cylinder is also just 2 times that of an unautofrettaged cylinder. The conclusions are the same as based on the 3rd strength theory, but some equations are different from each other.

Ultimate Bearing Capacity of Subsoils to Marine Pipelines

Based on the theory of limit analysis, the Finite Difference Method (FDM) is established for evaluating the ultimate bearing capacity of subsoils to bear the unburied pipelines. The analytical results of bearing capacity of the ideal clay is given. The approach to bearing capacity evaluation of cohesionless subsoils without surcharge is suggested. The results from this method are consistent with those obtained from model tests.

Development of mathematically motivated hybrid soft computing models for improved predictions of ultimate bearing capacity of shallow foundations

Ultimate bearing capacity(UBC)is a key subject in geotechnical/foundation engineering as it determines the limit of loads imposed on the foundation.The most reliable means of determining UBC is through experiment,but it is costly and time-consuming which has led to the development of various models based on the simplified assumptions.The outcomes of the models are usually validated with the experimental results,but a large gap usually exists between them.Therefore,a model that can give a close prediction of the experimental results is imperative.This study proposes a grasshopper optimization algorithm(GOA)and salp swarm algorithm(SSA)to optimize artificial neural networks(ANNs)using the existing UBC experimental database.The performances of the proposed models are evaluated using various statistical indices.The obtained results are compared with the existing models.The proposed models outperformed the existing models.The proposed hybrid GOA-ANN and SSA-ANN models are then transformed into mathematical forms that can be incorporated into geotechnical/foundation engineering design codes for accurate UBC measurements.

Methods for Estimating the Ultimate Bearing Capacity of Layered Foundations

The Meyerhof and Hanna′s(M-H) method to estimate the ultimate bearing capacity of layered foundations was improved. The experimental results of the load tests in Tianjin New Harbor were compared with predictions with the method recommended by the code for the foundations of harbor engineering, i.e. Hansen′s method and the improved M-H method. The results of the comparisons implied that the code and the improved M-H method could give a better prediction.

Evaluation of ultimate bearing capacity of Y-shaped vibro-pile

Based on Mindlin stress solution, a numerical computational method was proposed to calculate the stresses in the ground induced by side friction and the resistance of Y-shaped vibro-pile. The improved Terzaghi's and ЪерезанцевВГ's methods for ultimate bearing capacity evaluation were proposed by considering the stress strength induced by friction resistance at pile head level of Y-pile. A new method to calculate the ultimate bearing capacity of Y-pile was also proposed based on the assumptions of soil failure mode at the tip of Y-pile and the use of Mohr-Coulomb soil yield criterion and Vesic compressive correction coefficient with the induced stresses in the ground. Based on the comparisons with the field static load test results, it is found that the improved Terzaghi's method gives higher ultimate capacity, while the other two methods shows good agreement with the field results.

Revisiting the analytical solutions for ultimate bearing capacity of pile embedded in rocks

This paper investigates the validity and shortcomings of the existing analytical solution for the ultimate bearing capacity of a pile embedded in a rock mass using the modified HoekeBrown failure criterion.Although this criterion is considered a reference value for empirical and numerical calculations,some limitations of its basic simplifications have not been clarified yet.This research compares the analytical results obtained from the novel discontinuity layout optimization(DLO)method and the numerical solutions from the finite difference method(FDM).The limitations of the analytical solution are considered by comparing different DLO failure modes,thus allowing for the first time a critical evaluation of its scope and conditioning for implementation.Errors of up to 40%in the bearing capacity and unrealistic failure modes are the main issues in the analytical solution.The main aspects of the DLO method are also analyzed with an emphasis on the linearization of the rock failure criterion and the accuracy resulting from the discretization size.The analysis demonstrates DLO as a very efficient and accurate tool to address the pile tip bearing capacity,presenting considerable advantages over other methods.

Ultimate Bearing Capacity of Hollow Spherical Joints Welded with Circular Pipes under Eccentric Loads

The hollow spherical joints welded with circular pipes applied to the National Swimming Center of China are subjected to large bending moments, but the influence of bending moments is not considered in the design equations in Technical Specification for Latticed Shells. Based on the von Mises yield criterion, multilinear isotropic hardening rule and associated flow rule, the elasto-plastic finite element model is put forward to analyze the behavior of the joints, and a calculation method for the joints under bending moments or eccentric loads is proposed. It is shown by the analytical results of joint that the stiffening rib can improve the ultimate bearing capacity by 10% for joints under axial tensile load, by 40% for joints under axial compressive load, and by 50% for joints under bending moment. The unified calculation equations for joints with or without stiffening rib are put forward, which can be applied to calculating the ultimate bearing capacity of the hollow spherical joints with circular pipes under eccentric loads.