The new accelerator project （ HIRFL-CSR ） constructed at the Heavy Ion Research Facility in Lanzhou （HIRFL） is approaching completion. It is a multipurpose cooler-storage-ring system, consisting of a maim ring （C...The new accelerator project （ HIRFL-CSR ） constructed at the Heavy Ion Research Facility in Lanzhou （HIRFL） is approaching completion. It is a multipurpose cooler-storage-ring system, consisting of a maim ring （CSRm）, an experimental ring （CSRe） and two transfer beam lines. The UHV system of CSRm is the most representative subsystem in the project. To minimize the beam loss due to charge exchange of the heavy ions with the residual gas molecules, the pressure of the CSRm vacuum system should reach 3.5 × 10^-9 Pa （N2 equivalent） and the pressure of 8 × 10^-10 Pa is expected for very heavy ion such as uranium to make its lifetime longer than 50 s in the ring. Now, the vacuum system of CSRm has been completed and a pressure less than 5 × 10^-10 Pa has been obtained. In this paper the layout of the CSRm vacuum system, the vacuum equipment in CSRm, the treatment method for the CSRm vacuum chambers, and the installation and operation of the system will be reported.展开更多
Thin strain-relaxed Si0.81Ge0.19 films (95 nm) on the Ar+ ion implanted Si substrates with different ener- gies (30 keV,40 keV and 60 keV) at the same implanted dose (3×1015cm-2) were grown by ultra high vacuum c...Thin strain-relaxed Si0.81Ge0.19 films (95 nm) on the Ar+ ion implanted Si substrates with different ener- gies (30 keV,40 keV and 60 keV) at the same implanted dose (3×1015cm-2) were grown by ultra high vacuum chemi- cal vapor deposition (UHVCVD). Rutherford backscattering/ion channeling (RBS/C),Raman spectra as well as atomic force microscopy (AFM) were used to characterize these SiGe films. Investigations by RBS/C demonstrate that these thin Si0.81Ge0.19 films were epitaxially grown on the Ar+ ion implanted Si substrates,although there existed lots of crystal defects. The relaxation extent of Si0.81Ge0.19 films on the Ar+ implanted Si substrates is larger than that in the unimplanted case,which were verified by Raman spectra. Considering the relaxation extent of strain,surface roughness and crystal defects in these SiGe films,the thin relaxed SiGe film on the 30 keV Ar+ implanted Si substrate is optimal.展开更多
Problems continue to be encountered concerning the traditional vacuum preloading method in field during the treatment of newly deposited dredger fills.In this paper,an improved multiple-vacuum preloading method was de...Problems continue to be encountered concerning the traditional vacuum preloading method in field during the treatment of newly deposited dredger fills.In this paper,an improved multiple-vacuum preloading method was developed to consolidate newly dredger fills that are hydraulically placed in seawater for land reclamation in Lingang Industrial Zone of Tianjin City,China.With this multiplevacuum preloading method,the newly deposited dredger fills could be treated effectively by adopting a novel moisture separator and a rapid improvement technique without sand cushion.A series of model tests was conducted in the laboratory for comparing the results from the multiple-vacuum preloading method and the traditional one.Ten piezometers and settlement plates were installed to measure the variations in excess pore water pressures and moisture content,and vane shear strength was measured at different positions.The testing results indicate that water dischargeetime curves obtained by the traditional vacuum preloading method can be divided into three phases:rapid growth phase,slow growth phase,and steady phase.According to the process of fluid flow concentrated along tiny ripples and building of larger channels inside soils during the whole vacuum loading process,the fluctuations of pore water pressure during each loading step are divided into three phases:steady phase,rapid dissipation phase,and slow dissipation phase.An optimal loading pattern which could have a best treatment effect was proposed for calculating the water discharge and pore water pressure of soil using the improved multiple-vacuum preloading method.For the newly deposited dredger fills at Lingang Industrial Zone of Tianjin City,the best loading step was 20 kPa and the loading of 40-50 k Pa produced the highest drainage consolidation.The measured moisture content and vane shear strength were discussed in terms of the effect of reinforcement,both of which indicate that the multiple-vacuum preloading method has a better treatment effect not only in decreasing the moisture content and increasing the bearing capacity,but also in increasing the process uniformity at different depths of foundation.展开更多
The desire for practical utilization of rechargeable lithium batteries with high energy density has motivated attempts to develop new electrode materials and battery systems. Here, without additional binders we presen...The desire for practical utilization of rechargeable lithium batteries with high energy density has motivated attempts to develop new electrode materials and battery systems. Here, without additional binders we present a simple vacuum filtration method to synthesize nitrogen and sulfur codoped graphene(N,S-G) blocking layer, which is ultra-lightweight, conductive, and free standing. When the N,S-G membrane was inserted between the catholyte and separator, the lithium–selenium(Li–Se)batteries exhibited a high reversible discharge capacity of 330.7 mAh g^(-1) at 1 C(1 C = 675 mA g^(-1)) after 500 cycles and high rate performance(over 310 mAh g^(-1) at 4 C) even at an active material loading as high as ～5 mg cm^(-2). This excellent performance can be ascribed to homogenous dispersion of the liquid active material in the electrode, good Li^+-ion conductivity, fast electronic transport in the conductive graphene framework, andstrong chemical confinement of polyselenides by nitrogen and sulfur atoms. More importantly, it is a promising strategy for enhancing the energy density of Li–Se batteries by using the catholyte with a lightweight heteroatom doping carbon matrix.展开更多
By means of ultra-violet(UV)irradiation with photoini-tiator and multifunctional crosslinking agent,thecrosslinking modification of ultrahigh molecular weightpolyethylene(UHMWPE)fibers prepared by gel-spin-ning was ca...By means of ultra-violet(UV)irradiation with photoini-tiator and multifunctional crosslinking agent,thecrosslinking modification of ultrahigh molecular weightpolyethylene(UHMWPE)fibers prepared by gel-spin-ning was carried out.Thermal properties of fiber sampleswere examined using differential scanning calorimetry(DSC),thermomechanical analysis(TMA)apparatusand a manual device.The results indicated that the opti-mal irradiation energy is 250-400 mJ/cm^2,heat-andcreep-resistant behaviors of modified fibers have beenimproved.展开更多
Due to the low density and excellent mechanical proper-ties,high performance fiber reinforced materials have aconsiderable application in the area of high technologyand dally usage.In this paper,the Ultra-high Molecu-...Due to the low density and excellent mechanical proper-ties,high performance fiber reinforced materials have aconsiderable application in the area of high technologyand dally usage.In this paper,the Ultra-high Molecu-lar Weight Polyethylene(UHMWPE)fiber reinforcedPE tape prepared with the method of powder impregnat-ion was studied.The effect of impregnate length and thetensile force of the yarn on the fiber content as well as on the strength and modulus of the tape were discussed.Calculation shows that the strength and the modulus ofthe ULMWPE fiber can keep about 85％ after it undergothe process.展开更多
Synthesis of a m m oniu m alu min u m carbonate hydroxide ( A A C H) w as investigated usinga m m oniu m alu min u m sulfate and a m moniu m hydro carbonate as the starting m aterials . Itw as found that A A C Hca...Synthesis of a m m oniu m alu min u m carbonate hydroxide ( A A C H) w as investigated usinga m m oniu m alu min u m sulfate and a m moniu m hydro carbonate as the starting m aterials . Itw as found that A A C Hcan be synthesized by adding a m m oniu m alu m inu m sulfate solution torapidly stirred a m moniu m hydro - carbonate solution at a tem perature of 30 ℃. A A C Hcantransfor m to α Al2 O3 co m pletely by calcining at 1100 ℃ for 1 hour , and the obtained po w ders , with a particle size of 100 n m , can be sintered to 98 99 % relative density at 1500 ℃for 2 hours .展开更多
This work explored the way to improve hot modulus q/＇ rupture （HMOR） and refractoriness under load （RUL） by adding mild-calcined coal gangue （MCG） in Al2O3 -SiO2 ultra low cement （ULC） castables, making use o...This work explored the way to improve hot modulus q/＇ rupture （HMOR） and refractoriness under load （RUL） by adding mild-calcined coal gangue （MCG） in Al2O3 -SiO2 ultra low cement （ULC） castables, making use of the in-situ effect of the MCG during heating-up. The influence of respective additions of 5%, 10% and 1.5% of the MCG powders calcined at 700℃ was investigated on HMOR at 1400 ℃ and RUL of the castables. With increased addition of the MCG, HMOR and RUL become significantly enhanced. At 10% of the MCG addition, HMOR reaches 3 MPa, as compared to 0. 3 MPa in the case of no MCG addition. RUL of the specimens dried at 110 ℃for 24 h can be increased by some 270 ℃ with 10% of the MCG addition. RUL 0.11 the specimens preheated at 1 500℃ for 3 h maintains the growth trend with the MCG addition increasing. The microstructure of the heated castable samples was investigated by means of SEM. The in-situ formed needle-like and interlaced mullite in the matrix is contributive to the tmprovement.展开更多
Mutagenesis and retrotransposons have a close relationship, but little attention has been paid yet to the activity of retrotransposons produced by physical mutagens. The variation of retrotransposon WIS 2-1A activity ...Mutagenesis and retrotransposons have a close relationship, but little attention has been paid yet to the activity of retrotransposons produced by physical mutagens. The variation of retrotransposon WIS 2-1A activity in wheat （Triticum aestivum L.） embryos at three different growth times （30 h, 45 h and 60 h） was investigated after they had been treated with N^＋ implantation in a vacuum of 5× 10^-2 Pa and irradiation by ^60Coγ-ray respectively. For each of the three growth times the expression of WIS 2-1A showed almost entirely a same trend of downregulation, upregulation, then downregulation, and upregulation again with the increase in dose of N^＋ implantation, but the expression appeared irregular with the increase in irradiation of ^60Coγ-ray. In conclusion, the acutely activating effect of WIS 2-1A stimulated by vacuum and high dose N^＋ implantation within a shorter incubation time may provide a convenient tool to advance the research on mutagenic breeding and function genes.展开更多
文摘The new accelerator project （ HIRFL-CSR ） constructed at the Heavy Ion Research Facility in Lanzhou （HIRFL） is approaching completion. It is a multipurpose cooler-storage-ring system, consisting of a maim ring （CSRm）, an experimental ring （CSRe） and two transfer beam lines. The UHV system of CSRm is the most representative subsystem in the project. To minimize the beam loss due to charge exchange of the heavy ions with the residual gas molecules, the pressure of the CSRm vacuum system should reach 3.5 × 10^-9 Pa （N2 equivalent） and the pressure of 8 × 10^-10 Pa is expected for very heavy ion such as uranium to make its lifetime longer than 50 s in the ring. Now, the vacuum system of CSRm has been completed and a pressure less than 5 × 10^-10 Pa has been obtained. In this paper the layout of the CSRm vacuum system, the vacuum equipment in CSRm, the treatment method for the CSRm vacuum chambers, and the installation and operation of the system will be reported.
基金Partially supported by the National Natural Sciences Foundation of China (No.10075072)
文摘Thin strain-relaxed Si0.81Ge0.19 films (95 nm) on the Ar+ ion implanted Si substrates with different ener- gies (30 keV,40 keV and 60 keV) at the same implanted dose (3×1015cm-2) were grown by ultra high vacuum chemi- cal vapor deposition (UHVCVD). Rutherford backscattering/ion channeling (RBS/C),Raman spectra as well as atomic force microscopy (AFM) were used to characterize these SiGe films. Investigations by RBS/C demonstrate that these thin Si0.81Ge0.19 films were epitaxially grown on the Ar+ ion implanted Si substrates,although there existed lots of crystal defects. The relaxation extent of Si0.81Ge0.19 films on the Ar+ implanted Si substrates is larger than that in the unimplanted case,which were verified by Raman spectra. Considering the relaxation extent of strain,surface roughness and crystal defects in these SiGe films,the thin relaxed SiGe film on the 30 keV Ar+ implanted Si substrate is optimal.
基金the National Natural Science Foundation of China(NSFC)(Grant Nos.51378344 and 51578371)Tianjin Research Program of Application Foundation and Advanced Technology(Grant No.14JCYBJC21700)Beijing-Tianjin-Hebei Special Projects of Cooperation(Grant No.16JCJDJC40000) for their financial supports
文摘Problems continue to be encountered concerning the traditional vacuum preloading method in field during the treatment of newly deposited dredger fills.In this paper,an improved multiple-vacuum preloading method was developed to consolidate newly dredger fills that are hydraulically placed in seawater for land reclamation in Lingang Industrial Zone of Tianjin City,China.With this multiplevacuum preloading method,the newly deposited dredger fills could be treated effectively by adopting a novel moisture separator and a rapid improvement technique without sand cushion.A series of model tests was conducted in the laboratory for comparing the results from the multiple-vacuum preloading method and the traditional one.Ten piezometers and settlement plates were installed to measure the variations in excess pore water pressures and moisture content,and vane shear strength was measured at different positions.The testing results indicate that water dischargeetime curves obtained by the traditional vacuum preloading method can be divided into three phases:rapid growth phase,slow growth phase,and steady phase.According to the process of fluid flow concentrated along tiny ripples and building of larger channels inside soils during the whole vacuum loading process,the fluctuations of pore water pressure during each loading step are divided into three phases:steady phase,rapid dissipation phase,and slow dissipation phase.An optimal loading pattern which could have a best treatment effect was proposed for calculating the water discharge and pore water pressure of soil using the improved multiple-vacuum preloading method.For the newly deposited dredger fills at Lingang Industrial Zone of Tianjin City,the best loading step was 20 kPa and the loading of 40-50 k Pa produced the highest drainage consolidation.The measured moisture content and vane shear strength were discussed in terms of the effect of reinforcement,both of which indicate that the multiple-vacuum preloading method has a better treatment effect not only in decreasing the moisture content and increasing the bearing capacity,but also in increasing the process uniformity at different depths of foundation.
基金supported by the National Natural Science Foundation of China (51125001,51172005)the NSFCRGC Joint Research Scheme (51361165201)the Start-up Foundation of High-level Talents in Chongqing Technology and Business University (1856008)
文摘The desire for practical utilization of rechargeable lithium batteries with high energy density has motivated attempts to develop new electrode materials and battery systems. Here, without additional binders we present a simple vacuum filtration method to synthesize nitrogen and sulfur codoped graphene(N,S-G) blocking layer, which is ultra-lightweight, conductive, and free standing. When the N,S-G membrane was inserted between the catholyte and separator, the lithium–selenium(Li–Se)batteries exhibited a high reversible discharge capacity of 330.7 mAh g^(-1) at 1 C(1 C = 675 mA g^(-1)) after 500 cycles and high rate performance(over 310 mAh g^(-1) at 4 C) even at an active material loading as high as ～5 mg cm^(-2). This excellent performance can be ascribed to homogenous dispersion of the liquid active material in the electrode, good Li^+-ion conductivity, fast electronic transport in the conductive graphene framework, andstrong chemical confinement of polyselenides by nitrogen and sulfur atoms. More importantly, it is a promising strategy for enhancing the energy density of Li–Se batteries by using the catholyte with a lightweight heteroatom doping carbon matrix.
基金oral prepared in the Second East Asian Polymer Conference held in Hongkong,China,January 12-16,1999
文摘By means of ultra-violet(UV)irradiation with photoini-tiator and multifunctional crosslinking agent,thecrosslinking modification of ultrahigh molecular weightpolyethylene(UHMWPE)fibers prepared by gel-spin-ning was carried out.Thermal properties of fiber sampleswere examined using differential scanning calorimetry(DSC),thermomechanical analysis(TMA)apparatusand a manual device.The results indicated that the opti-mal irradiation energy is 250-400 mJ/cm^2,heat-andcreep-resistant behaviors of modified fibers have beenimproved.
文摘Due to the low density and excellent mechanical proper-ties,high performance fiber reinforced materials have aconsiderable application in the area of high technologyand dally usage.In this paper,the Ultra-high Molecu-lar Weight Polyethylene(UHMWPE)fiber reinforcedPE tape prepared with the method of powder impregnat-ion was studied.The effect of impregnate length and thetensile force of the yarn on the fiber content as well as on the strength and modulus of the tape were discussed.Calculation shows that the strength and the modulus ofthe ULMWPE fiber can keep about 85％ after it undergothe process.
文摘Synthesis of a m m oniu m alu min u m carbonate hydroxide ( A A C H) w as investigated usinga m m oniu m alu min u m sulfate and a m moniu m hydro carbonate as the starting m aterials . Itw as found that A A C Hcan be synthesized by adding a m m oniu m alu m inu m sulfate solution torapidly stirred a m moniu m hydro - carbonate solution at a tem perature of 30 ℃. A A C Hcantransfor m to α Al2 O3 co m pletely by calcining at 1100 ℃ for 1 hour , and the obtained po w ders , with a particle size of 100 n m , can be sintered to 98 99 % relative density at 1500 ℃for 2 hours .
文摘This work explored the way to improve hot modulus q/＇ rupture （HMOR） and refractoriness under load （RUL） by adding mild-calcined coal gangue （MCG） in Al2O3 -SiO2 ultra low cement （ULC） castables, making use of the in-situ effect of the MCG during heating-up. The influence of respective additions of 5%, 10% and 1.5% of the MCG powders calcined at 700℃ was investigated on HMOR at 1400 ℃ and RUL of the castables. With increased addition of the MCG, HMOR and RUL become significantly enhanced. At 10% of the MCG addition, HMOR reaches 3 MPa, as compared to 0. 3 MPa in the case of no MCG addition. RUL of the specimens dried at 110 ℃for 24 h can be increased by some 270 ℃ with 10% of the MCG addition. RUL 0.11 the specimens preheated at 1 500℃ for 3 h maintains the growth trend with the MCG addition increasing. The microstructure of the heated castable samples was investigated by means of SEM. The in-situ formed needle-like and interlaced mullite in the matrix is contributive to the tmprovement.
基金supported by National Natural Science Foundation of China(Nos.10505018,30800204)the Chinese Ministry of Agriculture(No.200803034)
文摘Mutagenesis and retrotransposons have a close relationship, but little attention has been paid yet to the activity of retrotransposons produced by physical mutagens. The variation of retrotransposon WIS 2-1A activity in wheat （Triticum aestivum L.） embryos at three different growth times （30 h, 45 h and 60 h） was investigated after they had been treated with N^＋ implantation in a vacuum of 5× 10^-2 Pa and irradiation by ^60Coγ-ray respectively. For each of the three growth times the expression of WIS 2-1A showed almost entirely a same trend of downregulation, upregulation, then downregulation, and upregulation again with the increase in dose of N^＋ implantation, but the expression appeared irregular with the increase in irradiation of ^60Coγ-ray. In conclusion, the acutely activating effect of WIS 2-1A stimulated by vacuum and high dose N^＋ implantation within a shorter incubation time may provide a convenient tool to advance the research on mutagenic breeding and function genes.
