Experimental study on Ti+Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the ferrite region

A Ti＋Nb bearing ultra-low carbon bake hardening sheet steel hot-rolled in the conventional austenite region and in the ferrite region with lubrication was experimentally studied. Subsequent cold rolling and continuous annealing processes were also conducted. The results show that microstructures of ultra-low carbon bake hardening hot strips at room temperature are basically irregular polygonal ferrites. The yield strength, ultimate tensile strength, n value, and r value of the No.2 specimen hot-rolled in the ferrite region with lubrication are 243 MPa, 364 MPa, 0.29, and 1.74, respectively, which are similar to those of the No.1 specimen hot-roiled in the conventional austenite region. The elongation rate and bake hardening value of No.2 specimen are 51% and 49.4 MPa, respectively, which are greater than those of No. 1 specimen. The No.2 specimen hot-rolled in the ferrite region with lubrication exhibits good mechanical properties and relatively excellent baking hardening performance. Therefore, the hot rolling experiment of Ti＋Nb bearing ultra-low carbon bake hardening steel in the ferrite region with lubrication is feasible and can be considered in the future industrial trial production.

Decarburization rate of RH refining for ultra low carbon steel

The decarburization behaviors of ultra low carbon steel in a 210-t RH vacuum degasser were investigated under practical operat- ing conditions. According to the apparent decarburization rate constant （Kc） calculated by the carbon content in the samples taken from the hot melt in a ladle at an interval of 1-2 min, it is observed that the total decarburization reaction period in RH can be divided into the quick decarburization period and the stagnant decarburization period, which is quite different from the traditional one with three stages. In this study, the average apparent decarburization rate constant during the quick decarburization period is 0.306 min^-1, and that of the stagnant period is 0.072 min^-1. Increasing the initial carbon content and enhancing the exhausting capacity can increase the apparent decarburization rate constant in the quick decarburization period. The decarburization reaction comes into the stagnant decarburization period when the carbon content in molten steel is less than 14× 10^-6 after 10 min of decarburization.

Effect of temper rolling on the bake-hardening behavior of low carbon steel

In a typical process, low carbon steel was annealed at two different temperatures （660℃ and 750℃）, and then was temper rolled to improve the mechanical properties. Pre-straining and baking treatments were subsequently carried out to measure the bake-hardening （BH） values. The influences of annealing temperature and temper rolling on the BH behavior of the steel were investigated. The results indicated that the microstructure evolution during temper rolling was related to carbon atoms and dislocations. After an apparent increase, the BH value of the steel significantly decreased when the temper rolling reduction was increased from 0%to 5%. This was attributed to the increase in solute carbon concentration and dislocation density. The maximum BH values of the steel annealed at 660℃ and 750℃ were 80 MPa and 89 MPa at the reductions of 3%and 4%, respectively. Moreover, increasing the annealing temperature from 660 to 750℃ resulted in an ob-vious increase in the BH value due to carbide dissolution.

Novel mechanism for the modification of Al_2O_3-based inclusions in ultra-low carbon Al-killed steel considering the effects of magnesium and calcium

Many researchers have explored the inclusion modification mechanism to improve non-metallic inclusion modifications in steelmaking. In this study, two types of industrial trials on inclusion modifications in liquid steel were conducted using ultra-low-carbon Al-killed steel with different Mg and Ca contents to verify the effects of Ca and Mg contents on the modification mechanism of Al_2O_3-based inclusions during secondary refining. The results showed that Al_2O_3-based inclusions can be modified into liquid calcium aluminate or a multi-component inclusion with the addition of a suitable amount of Ca. In addition, [Mg] in liquid steel can further reduce CaO in liquid calcium aluminate to drive its evolution into CaO–MgO–Al_2O_3 multi-component inclusions. Thermodynamic analysis confirmed that the reaction between [Mg] and CaO in liquid calcium aluminate occurs when the MgO content of liquid calcium aluminate is less than 3 wt% and the temperature is higher than 1843 K.

Structure Character of M-A Constituent in CGHAZ of New Ultra-Low Carbon Bainitic Steel under Laser Welding Conditions

800 MPa grade new ultra-low carbon bainitic （NULCB） steel is the recently developed new generation steel. The microstructure in the coarse-grained heat affected zone （CGHAZ） of NULCB steel under laser welding conditions was investigated by thermal simulation. The influence of the cooling time from 800℃ to 500℃.t8/5 （0.3-30 s）, on the microstructure of the CGHAZ was discussed. The experimental results indicate that the microstructnre of the CGHAZ is only the granular bainite which consists of bainitic ferrite （BF） lath and M-A constituent while t8/5 is 0.3-30 s. The M-A constituent consists of twinned martensite and residual austenite, and the change of the volume fraction of the residual austenite in the M-A constituent is very small when t8/5 is between 0.3 and 30 s. The morphology of the M-A constituent obviously changes with the variation of t8/5.As t8/5 increases, tile average width, gross and shape parameter of the M-A constituent increase, while the line density of the M-A constituent decreases.

Mathematical Model of Decarburization of Ultra Low Carbon Steel during RH Treatment

According to the balance of carbon and oxygen, a decarburization model for the RH treatment has been developed. in which the influence of the mass transfer of carbon and oxygen in the liquid steel and the stirring energy (ε) in the vacuum vessel on decarburization rate has been considered. The conclusion that the volumetric coefficients of the mass transfer of carbon is proportional to ε(1.5) is drawn. Industrical experiment proves this model is reliable. The influence of some factors on decarburization rate has been obtained. which can provide directions for RH treatment The decarburization behavior of steel with RH-OB treatment is also studied. The OB-or-not curve, the optimized OB time and OB amount are discussed.

Isothermal precipitation behavior of copper sulfide in ultra low carbon steel

Copper and sulfur are typical residual elements or impurity elements in steel.Sufficient removal of them during steelmaking process is difficult for copper and costly for sulfur.Utilization of copper and sulfur in steel, especially in steel scrap,has been an important issue for a long period for metallurgists.Copper and sulfur may combine to form copper sulfide,which may provide a prospect to avoid the detrimental effects of copper and sulfur in steel.Unfortunately the formation mechanism of copper sulfide in steel has not been completely clarified so far. In the present paper,solution treatment of samples containing copper and sulfur are firstly performed at 1623 K for 2.7×10~3 s followed by quenching into water.The samples are then isothermally heat-treated at 673 K,873 K, 1073 K,1273 K and 1373K for different time followed by quenching into water again.The size,morphology, constituent and crystallography of sulfide precipitates in these samples are investigated by scanning electron microscope(SEM) and TEM equipped with EDS.Fine copper sulfides(less than 100 nm) are observed to coexist with silicon oxide in samples even isothermally heat-treated at 1 373 K for 1.44×10~4 s;Film-like copper sulfides are generally observed to co-exist with iron sulfide in all samples;Plate-like copper sulfides are observed especially in sample isothermally heat-treated at 1 073 K for 1.44×10~4 s.The formation mechanisms of these copper sulfides have been discussed.

Advanced manufacturing technologies of large martensitic stainless steel castings with ultra low carbon and high cleanliness

The key manufacturing technologies associated with composition, microstructure, mechanical properties, casting quality and key process control for large martensitic stainless steel castings are involved in this paper. The achievements fully satisfeid the technical requirements of the large 700 MW stainless steel hydraulic turbine runner for the Three Gorges Hydropower Station, and become the major technical support for the design and manufacture of the largest 700 MW hydraulic turbine generator unit in the world developed through our own efforts. The characteristics of a new high yield to tensile strength (R p0.2/R m ) ratio and high obdurability martensitic stainless steel with ultra low carbon and high cleanliness are also described. Over the next ten years, the large martensitic stainless steel castings and advanced manufacturing technologies will see a huge demand in clean energy industry such as nuclear power, hydraulic power at home and abroad. Therefore, the new high yield o tensile strength (R p0.2/R m ) ratio and high obdurability martensitic stainless steel materials, the fast and flexible manufacturing technologies of large size castings, and new environment friendly sustainable process will face new challenges and opportunities.

Effect of an upward magnetic field on nanosized sulfide precipitation in ultra-low carbon steel

An induction levitation melting （ILM） refining process is performed to remove most microsized inclusions in ultra-low carbon steel （UCS）. Nanosized, spheroid shaped sulfide precipitates remain dispersed in the UCS. During the ILM process, the UCS is molten and is rotated under an upward magnetic field. With the addition of Ti additives, the spinning molten steel under the upward magnetic field ejects particles because of resultant centrifugal, floating, and magnetic forces. Magnetic force plays a key role in removing sub-micrometer-sized particles, composed of porous aluminum titanate enwrapping alumina nuclei. Consequently, sulfide precipitates with sizes less than 50 nan remain dispersed in the steel matrix. These findings open a path to the fabrication of clean steel or steel bearing only a nanosized strengthen- ing phase.

Deformation Behavior of Ultra-low Carbon Steel in Ferrite Region during Warm Processing

The hot deformation experiments of ultra-low carbon steel in ferrite range were carried out in a hot simulator in order to research hot deformation behaviors of ultra-low carbon steel in ferrite range at low temperature. The results show that the influences of deformation parameters on flow stress are different to those in austenitic deformation. The deformation characteristic parameters were calculated for ultra-low carbon steel in ferrite region. The flow stress equation for ultra-low carbon steel in ferritic deformation at low temperature was obtained.

Mechanical Method Determining Precipitation in an Ultra-Low Carbon Bainitic Steel

Stress relaxation was chosen as the best method for monitoring the precipitation process. Tests were carried out on an ultra-low carbon bainitic steel containing Mn, Nb and B over 800~950℃. Specimens were solu- tion treated at 1250℃ for a certain holding period. A prestain of 20% was applied at a strain rate of 0.1/s. The exper- imental results are displayed by a set of stress vs. 1g(time) curves different from the typical stress relaxation curves. There are two singularities forming a stress plateau on the stress vs.1g(time) curves when precipitates could be observed. Suppose the first one is the start of precipitation (Ps), and the second represcnts the fihish (Pf). As a result Precipitation-Time-Temperature relationship is described as C-shape curves based on two points. This mechanical method is suitable and precise for measuring precipitates in microalloyed steels during hot working.

Optimum process of RH-MFB refining for ultra-low carbon steel

A mathematical model was established and applied to simulate thedecarburization of RH-MFB process in Pansteel Company. Study of theeffects of w_[C]0, w_[O]0, Ar flowrate, evaluation rate the MFB lanceblowing parameters on the decarburization process was car- Ried out.The results showed that this model could give the quantitativeunderstanding of the process, especially the behavior of MFB Lanceblowing. This model has realized the optimum process of RH-MFBrefining for ultra-low carbon steels in Pansteel.

Experimental Procedure and Hardening Model to Consider Forming and Baking Effects in Simulation

This paper investigated an experimental method for bake hardening properties, a technique for deriving the true stress-strain curves after reaching the maximum load, and a constitutive equation considering both work hardening and bake hardening in order to apply the work hardening occurring in the forming process of parts and the bake hardening induced in the baking process to an automotive crash simulation. A general bake hardening test is that a pre-tensioned specimen is baked and then the same specimen is tensioned again without any further treatment. For a bake hardening test of automotive steel with a tensile strength of 1.2 GPa or more, fractures often occur in curvature section outside, an extensometer due to the difference in the material strength caused by non-uniform bake hardening. This causes a problem in that the bake hardening properties cannot be obtained. In this paper, to prevent curvature fracture, tensile specimens were re-machined in the uniformly deformed region of large specimens subjected to pre-strain, and the re-machined specimens with uniform strength in all regions were re-tensioned. In the bake hardening test of ultra-high strength steels with a tensile strength of 1 GPa or more, shear band fractures occur when the pre-strain is large. This makes it impossible to obtain a true stress-strain curve because there is no uniformly deformed region under a tensile test. To overcome this problem, a new method to calculate the true stress-strain curve by comparing experimental results and the load calculated by the local strain obtained from digital images was developed. This method can be applied not only where shear band deformation occurs, but also in necking deformation, and true stress-strain curves for strains up to 2 - 3 times the uniform elongation can be obtained. A new constitutive equation was developed since an appropriate hardening model is required to simultaneously apply the work hardening and the bake hardening to the simulation. For the newly developed model, the user material subroutine of LS-Dyna was configured, and the simulation was performed on the single hat specimens with pre-strain. When both work hardening and bake hardening were considered, there was a significant increase in absorbed energy compared to when only work hardening was considered. This means that both work hardening and bake hardening should be considered in the car crash simulations to enhance the accuracy of the simulation.

The micro structure of high carbon low alloy steel for easy drawing

For better processing performance of high carbon low alloy steel wire rod,an investigation about the influence of cementite lamellar spacing on wire 'easy drawing' performance is completed.It is pointed out that too thin cementite lamellar spacing(<80 um) reduces the strain hardening level of wire drawing, and reduce the torsion performance of drawn wire at same time.For the wire or wire rod from industrial production,compared with the micro-structure with troostite,the micro-structure with sorbite or sorbite mixed with pearlite is more suitable to the drawing process with high reduction ratio.

Effect of annealing time and phosphorus addition on bake hardening behavior of ultra-low carbon bake hardening steel

The relationship of the P and C grain boundary segregation and its effect on bake hardening behavior were investigated in ultra-low carbon bake hardening (ULC-BH)steel with and without P addition annealed at 810 ℃ for various time using electron probe micro-analyzer,electroh backscattered diffraction,and three-dimensional atomic probe techniques.Results revealed that P addition and annealing duration considerably affected the bake hardening behavior of experimental steel. The BH value of ULC-BH steel without P addition is lower than that with P addition within a short annealing time,and the difference in the BH value gradually decreases as the annealing duration is prolonged.P segregation is dominant in terms of a high P bulk content in steels with P addition at the expense of C segregation during annealing.By contrast,opposite effects are observed in low carbon bake hardening steel.The high residual solute C content in steel with P addition is due to P segregation at the grain boundary.Site competition is mainly responsible for the lower BH value in ULC-BH steel without P addition than that with P addition.As the annealing time is further extended,C segregation begins at grain boundary despite the delayed P segregation,leading to a gradual decrease in the solute concentration in the matrix of steels with P addition.C and P segregations reach the equilibrium as the annealing time increases to 60 min at 810 ℃ in the two steel samples.Theoretical calculations reveal that the residual solute C concentration in the matrix decreases to zero,and this finding is consistent with the change trend of the bake hardening value.Hence,the C segregation at grain boundary. adversely influences the bake hardening property of ULC-BH steel.

Microstructure and Property of Coarse Grain HAZ X80 Pipeline Steel

The coarse grain HAZ microstructure and property of X80 pipeline steel with different carbon content was investigated. The weld thermal simulation test was carried out on Gleeble 1500 thermal mechanical test machine. The Charpy tests were completed at --20 ℃ for evaluating the toughness of coarse grain heat affected zone （CGHAZ）. The microstructure was examined by optical microscope （OM） and transmission electron microscopy （TEM）, and the austenite constituent was quantified by X-ray diffraction. The results showed that the ultra-low carbon can improve the toughness of CGHAZ by suppressing the formation of carbide, decreasing the martensite austenite （M-A） constituent and increasing the residual austenite in the M A.

Continuous Cooling Transformation Behavior and Kinetic Models of Transformations for an Ultra-Low Carbon Bainitic Steel

The aim was to investigate transformation behavior and transformation kinetics of an ultra-low carbon bai- nitic steel during continuous cooling. Continuous cooling transformation （CCT） curves of tested steel were measured by thermal dilatometer and metallographic structures at room temperature were observed by optical microscope. Then transformation kinetic equation of austenite to ferrite as well as austenite to bainite was established by analyzing the relationship of lnln]-l/（1--f）] and lnt in the kinetic equation on the basis of processed experimental data. Finally, the measured and calculated kinetic behaviors of the steel during continuous cooling were compared and growth pat- terns of transformed ferrite and bainite were analyzed. Results showed that calculated result was in reasonable agree- ment with the experimental data. It could be concluded that the growth modes of transformed ferrite and bainite were mainly one dimension as the Avrami exponents were between 1 and 2.

A method for observing the three-dimensional morphologies of inclusions in steel

A method for observing the three-dimensional morphologies of inclusions by deeply eroding a steel sample with a kind of organic solution composed of bromine water, acetone, and HCl （volume ratio, 45：45：10） was introduced. Four different kinds of inclusions in ultra low carbon steel were compared by metallographic observation and erosion observation. The results show that the three-dimensional morphologies of different kinds of inclusions could be observed clearly and simply after erosion. The method is useful for the observation and analysis of inclusions made by deep erosion. It also provides a new way to control and remove inclusions based on the true morphologies of inclusions.

Microstructure and Properties of Ti and Ti+Nb Ultra-Low-Carbon Bake Hardened Steels

Hot rolling, cold rolling and continuous annealing processes of Ti bearing and Ti＋ Nb stabilized ultra-low-carbon bake hardened steels were experimentally studied. The microstructure and texture evolution, as well as the morphology, size and distribution of second phase precipitates during hot rolling, cold rolling and continuous annealing were also analyzed. The results showed that the size of NbC precipitates in Ti＋Nb stabilized ultra-low-carbon bake hardened steel was smaller than that of TiC precipitates in Ti bearing ultra-low-carbon bake hardened steel, which made the average grain size of Ti＋ Nb stabilized ultra-low-carbon bake hardened steel finer than that of Ti bearing ultra-low-carbon bake hardened steel; for the yield strength, the former was higher than the latter; but for the r value which reflects the deep-drawing performance, the former was lower than the latter.

Carbon and oxygen behavior in the RH degasser with carbon powder addition

For ultra-low-carbon(ULC)steel production,the higher oxygen content before Ruhrstahl-Heraeus(RH)decarburization(de-C)treatment could shorten the de-C time in the RH degasser.However,this would lead to oxidation rates being exceeded by molten steel production,affecting ULC steel surface quality.In this work,a carbon powder addition(CPA)process was proposed to reduce the dissolved oxygen content at the end of RH de-C through addition of carbon powder to molten steel in the vacuum vessel.Carbon and oxygen behavior during the CPA and conventional process was then studied.The results demonstrated that the de-C rate with CPA was lower compared to the conventional process,but the carbon content at the end of de-C presented no difference.The de-C reaction for CPA process took place in the four reaction sites:(1)within the bulk steel where the spontaneous CO bubbles form;(2)splashing area on the liquid steel surface;(3)Ar bubble surface;(4)molten steel surface.The CPA process could significantly reduce the dissolved oxygen content at the end of de-C,the sum content of FeO and MnO in the slag,the aluminum consumption,and the defect rate of rolled products.This was beneficial in improving ULC steel cleanliness.