Comparative impact behaviours of ultra high performance concrete columns reinforced with polypropylene vs steel fibres

Polypropylene(PP) fibres have primarily used to control shrinkage cracks or mitigate explosive spalling in concrete structures exposed to fire or subjected to impact/blast loads, with limited investigations on capacity improvement. This study unveils the possibility of using PP micro-fibres to improve the impact behaviour of fibre-reinforced ultra-high-performance concrete(FRUHPC) columns. Results show that the addition of fibres significantly improves the impact behaviour of FRUHPC columns by shifting the failure mechanism from brittle shear to favourable flexural failure. The addition of steel or PP fibres affected the impact responses differently. Steel fibres considerably increased the peak impact force(up to 18%) while PP micro-fibres slightly increased the peak(3%-4%). FRUHPC significantly reduced the maximum midheight displacement by up to 30%(under 20°impact) and substantially improved the displacement recovery by up to 100%(under 20° impact). FRUHPC with steel fibres significantly improved the energy absorption while those with PP micro-fibres reduced the energy absorption, which is different from the effect of PP-macro fibre reported in the literature. The optimal fibre content for micro-PP fibres is 1% due to its minimal fibre usage and low peak and residual displacement. This study highlights the potential of FRUHPC as a promising material for impact-resistant structures by creating a more favourable flexural failure mechanism, enhancing ductility and toughness under impact loading, and advancing the understanding of the role of fibres in structural performance.

Effect of Strain Ratio on Fatigue Model of Ultra-fine Grained Pure Titanium

The ultra-fine grained(UFG)pure titanium was prepared by equal channel angular pressing(ECAP)and rotary swaging(RS).The strain controlled low cycle fatigue(LCF)test was carried out at room temperature.The fatigue life prediction model and mean stress relaxation model under asymmetrical stress load were discussed.The results show that the strain ratio has a significant effect on the low cycle fatigue performance of the UFG pure titanium,and the traditional Manson-coffin model can not accurately predict the fatigue life under asymmetric stress load.Therefore,the SWT mean stress correction model and three-parameter power curve model are proposed,and the test results are verified.The final research shows that the threeparameter power surface model has better representation.By studying the mean stress relaxation phenomenon under the condition of R≠-1,it is revealed that the stress ratio and the strain amplitude are the factors that significantly afiect the mean stress relaxation rate,and the mean stress relaxation model with the two variables is calculated to describe the mean stress relaxation phenomenon of the UFG pure titanium under different strain ratios.The fracture morphology of the samples was observed by SEM,and it was concluded that the final fracture zone of the fatigue fracture of the UFG pure titanium was a mixture of ductile fracture and quasi cleavage fracture.The toughness of the material increases with the increase of strain ratio at the same strain amplitude.

Overview of Jute Fibre as Thermoplastic Matrix Polymer Reinforcement

Recent decades have seen a substantial increase in interest in research on natural fibres that is aligned with sustainable development goals(SDGs).Due to their renewable resources and biodegradability,natural fiberreinforced composites have been investigated as a sustainable alternative to synthetic materials to reduce the usage of hazardous waste and environmental pollution.Among the natural fibre,jute fibre obtained from a bast plant has an increasing trend in the application,especially as a reinforcement material.Numerous research works have been performed on jute fibre with regard to reinforced thermoset and thermoplastic composites.Nevertheless,current demands on sustainable materials have required new developments in thermoplastic composites.In this paper,the author reviews jute plants as reinforcement materials for thermoplastic matrix polymers.This review provides an overview of the sustainability of jute plants as reinforcement material for thermoplastic matrix polymers.The overview on jute based thermoplastic composites focused on the thermal behavior and mechanical properties.Apart from physical,chemical,and mechanical properties,the study also covers the current and perspectives for future research challenges faced by the researchers on jute fibre reinforced thermoplastic composites.

Can waste textiles be completely transformed into fibres?

The advancement and novel technologies in materials science have been steadily growing toward adopting ethical practices.To reduce the stress on the environment the producers integrate novel materials to extend traditional functionality.They develop modern fibers that are eco-friendly,light,resilient,mechanically flexible,and easy to process.Moreover,novel fabrics are acquiring unique properties such as sensory capabilities,electrical conductivity,and data transmission.Cloths with characteristics such as hydrophobic cotton,plant-based textiles,antimicrobial fabrics,and shape memory polymers show versatility in textile innovations.Overall,these textile innovations provide sustainable alternatives,which are commercially viable and suitable for large-scale production.

Effect of silica fume and glass powder for enhanced impact resistance in GGBFS-based ultra high-performance geopolymer fibrous concrete:An experimental and statistical analysis

Solid waste recycling is an economically sound strategy for preserving the environment,safeguarding natural resources,and diminishing the reliance on raw material consumption.Geopolymer technology offers a significant advantage by enabling the reuse and recycling of diverse materials.This research assesses how including silica fume and glass powder enhances the impact resistance of ultra-high-performance geopolymer concrete(UHPGC).In total,18 distinct mixtures were formulated by substituting ground granulated blast furnace slag with varying proportions of silica fume and glass powder,ranging from 10%to 40%.Similarly,for each of the mixtures above,steel fibre was added at a dosage of 1.5%to address the inherent brittleness of UHPGC.The mixtures were activated by combining sodium hydroxide and sodium silicate solution to generate geopolymer binders.The specimens were subjected to drop-weight impact testing,wherein an examination was carried out to evaluate various parameters,including flowability,density at fresh and hardened state,compressive strength,impact numbers indicative of cracking and failure occurrences,ductility index,and analysis of failure modes.Additionally,the variations in the impact test outcomes were analyzed using the Weibull distribution,and the findings corresponding to survival probability were offered.Furthermore,the microstructure of UHPGC was scrutinized through scanning electron microscopy.Findings reveal that the specimens incorporating glass powder exhibited lower cracking impact number values than those utilizing silica fume,with reductions ranging from 18.63%to 34.31%.Similarly,failure impact number values decreased from 8.26%to 28.46%across glass powder contents.The maximum compressive and impact strength was recorded in UHPGC,comprising 10%silica fume with fibres.

Path-Dependent Progressive Failure Analysis for 3D-Printed Continuous Carbon Fibre Reinforced Composites

In order to predict the damage behaviours of 3D-printed continuous carbon fibre(CCF)reinforced composites,when additional short carbon fibre(SCF)composite components are employed for continuous printing or special functionality,a novel path-dependent progressive failure(PDPF)numerical approach is developed.First,a progressive failure model using Hashin failure criteria with continuum damage mechanics to account for the damage initiation and evaluation of 3D-printed CCF reinforced polyamide(PA)composites is developed,based on actual fibre placement trajectories with physical measurements of 3D-printed CCF/PA constituents.Meanwhile,an elastic-plastic model is employed to predict the plastic damage behaviours of SCF/PA parts.Then,the accuracy of the PDPF model was validated so as to study 3D-printed CCF/PA composites with either negative Poisson's ratio or high stiffness.The results demonstrate that the proposed PDPF model can achieve higher prediction accuracies in mechanical properties of these 3D-printed CCF/PA composites.Mechanism analyses show that the stress distribution is generally aggregated in the CCF areas along the fibre placement paths,and the shear damage and matrix tensile/compressive damage are the key damage modes.This study provides a new approach with valuable information for characterising complex 3D-printed continuous fibre-matrix composites with variable mechanical properties and multiple constituents.

In Situ Polymer Gel Electrolyte in Boosting Scalable Fibre Lithium Battery Applications

The poor interfacial stability not only deteriorates fibre lithium-ion batteries(FLBs)performance but also impacts their scalable applications.To efficiently address these challenges,Prof.Huisheng Peng team proposed a generalized channel structures strategy with optimized in situ polymerization technology in their recent study.The resultant FLBs can be woven into different-sized powering textiles,providing a high energy density output of 128 Wh kg^(-1) and simultaneously demonstrating good durability even under harsh conditions.Such a promising strategy expands the horizon in developing FLB with particular polymer gel electrolytes,and significantly ever-deepening understanding of the scaled wearable energy textile system toward a sustainable future.

Optical Fibre Communication Feature Analysis and Small Sample Fault Diagnosis Based on VMD-FE and Fuzzy Clustering

To solve the problems of a few optical fibre line fault samples and the inefficiency of manual communication optical fibre fault diagnosis,this paper proposes a communication optical fibre fault diagnosis model based on variational modal decomposition(VMD),fuzzy entropy(FE)and fuzzy clustering(FC).Firstly,based on the OTDR curve data collected in the field,VMD is used to extract the different modal components(IMF)of the original signal and calculate the fuzzy entropy(FE)values of different components to characterize the subtle differences between them.The fuzzy entropy of each curve is used as the feature vector,which in turn constructs the communication optical fibre feature vector matrix,and the fuzzy clustering algorithm is used to achieve fault diagnosis of faulty optical fibre.The VMD-FE combination can extract subtle differences in features,and the fuzzy clustering algorithm does not require sample training.The experimental results show that the model in this paper has high accuracy and is relevant to the maintenance of communication optical fibre when compared with existing feature extraction models and traditional machine learning models.

BTMA’s advanced fibre focus at Techtextil 2024

New fibres continue to be developed for a wide range of technical textile applications.Currently,they include fibres based on organic or recycled feedstocks to meet sustainability targets and others with new functional properties for advanced high performance applications.Many of them were showcased at the forthcoming Techtextil 2024 exhibition which takes place in Frankfurt,Germany,from April 23-26.The development of specific multifilaments,monofilaments and nonwovens for niche fibre applications–over 70 to date–is very much the specialist field of BTMA member Fibre Extrusion Technologies(FET),along with designing the bespoke fibre extrusion and spunbond and meltblown nonwoven systems to successfully produce them.

Preparation technology of ultra-fine powders of Auricularia auricular

Conventional mechanical method and mechanical method combined with vacuum freeze-drying technology were used to make the ultra-fine powders of edible fungus (Auricularia auricular). The content of basic nutrients, amino acid, micro structure and their properties of raw edible fungus and the edible fungus powders obtained with the two methods were analyzed and compared. The granularity size and micro-structure of the pulverized samples were analyzed by SEM and TEM technology. The average granularity size of the edible fungus powder obtained with mechanical method was 1–5 μm, while that obtained with mechanical method combined with vacuum freeze-drying process was 0.5–1 μm. The ultra-fine powders of edible fungus obtained with the two methods had better water recovery capability and quality, and their preserving time was longer than that of raw edible fungus. All the properties of the ultra-fine powders of edible fungus obtained with the vacuum freeze-drying technology were evidently superior to that of the conventional mechanical method. Keywords Auricularia auricula - Edible fungus - Ultra-fine powders - Vacuum freeze-drying CLC number TS205 Document code B Biography: YANG Chun-yu (1975), female, Ph. D. in Engineering Technology Center of Forestry and Wood Workine, Machinery, Northeast Forestry University, Harbin 150040, P. R. China.Responsible editor: Zhu Hong

Preparation of ultra-fine grain Ni-Al-WC coating with interlocking bonding on austenitic stainless steel by laser clad and friction stir processing

The ultra-fine structured Ni?Al?WC layer with interlocking bonding was fabricated on austenitic stainless steel by combination of laser clad and friction stir processing (FSP). Laser was initially applied to Ni?Al elemental powder preplaced on the austenitic stainless steel substrate to produce a coating for further processing. The as-received coating was subjected to FSP treatment, processed by a rotary tool rod made of WC?Co alloy, to obtain sample for inspection. Microstructure, phase constitutions, hardness and wear property were investigated by methods of scanning electronic microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDX) microanalysis, and X-ray diffraction (XRD), hardness test alongside with dry sliding wear test. The results show that the severe deformation effect exerted on the specimen resulted in an ultra-fine grain layer of about 100μmin thickness and grain size of 1?2μm. Synergy between introduction of WC particles to the deformation layer and deformation strengthening contributes greatly to the increase in hardness and friction resistance. An interlocking bonding between the coating and matrix which significantly improves bonding strength was formed due to the severe deformation effect.

Fabrication of SiC fibres from yttrium-containing polycarbosilane

The yttrium as a sintering aid was introduced into polycarbosilane（PCS） to prepare yttrium-containing PCS（PYCS）.Two types of yttrium-containing SiC fibres,the SiC（OY） fibres and the SiC（Y） fibres,were fabricated with PYCS.The structural evolution and the associated properties on changing from SiC（OY） to SiC（Y） fibres during the sintering process were studied.The chemical composition of the SiC（OY） fibres is SiC1.53O0.22Y0.005 with an amorphous structure.The composition of SiC（Y） fibres is SiC1.23O0.05Y0.005.The fibres are composed of a large number of β-SiC crystallites with a size of 50 nm and a small amount of α-SiC crystalline.The tensile strength and fracture toughness of the SiC（OY） fibres are 2.25 GPa and 2.37 MPa·m1/2,respectively,and 1.61 GPa,1.91 MPa·m1/2,respectively for SiC（Y） fibres.The SiC（Y） fibres have a higher thermal stability than the SiC（OY） fibres.

Evaluation of ultra-fine grained tungsten under transient high heat flux by high-intensity pulsed ion beam

Pure tungsten, oxide dispersion strengthened tungsten and carbide dispersion strengthened tungsten were fabricated by high-energy ball milling and spark plasma sintering process. In order to evaluate the properties of the tungsten alloys under transient high heat flues, four tungsten samples with different grain sizes were tested by high-intensity pulsed ion beam with a heat flux as high as 160 MW/（m^2·s^-1/2）. Compared with the commercial tungsten, the surface modification of the oxide dispersion strengthened tungsten by high-intensity pulsed ion beam is completely different. The oxide dispersion strengthened tungsten shows inferior thermal shock response due to the low melting point second phase of Ti and Y2O3, which results in the surface melting, boiling bubbles and cracking. While the carbide dispersion strengthened tungsten shows better thermal shock response than the commercial tungsten.

Caustics study of the effect of glass fibres on dynamic fracture of hardened cement paste

The reflected optical caustics method is applied to study dynamic fracture problems in hardened cement paste. First both the unreinforced cement paste and the glass fibres reinforced cement paste specimens were fabricated and the reflective coating on the surface of the specimen was prepared. Secondly the crack path and the shadow spot patterns during the crack propagation process for the two specimens were recorded by using a multi-spark high speed camera.Thirdly some dynamic parameters of two cement paste specimens including crack onset time the dynamic stress intensity factor and crack growth velocity were determined and analyzed comparatively.This indicates that the glass fibres can improve the fracture resistance and delay fracture time.These results will play an important role in evaluating the dynamic fracture properties of cement paste.

Fracture Properties of Cement Composites Reinforced with Steel Polypropylene Hybrid Fibres

Polypropylene fibres and three sizes of steel fibres reinforced concrete are discussed. The total fibres content ranges from 0 4%-0 95% by volume of concrete. A four point bending test is adopted on the notched prisms with the size of 100?mm×100?mm×500?mm to investigate the effect of hybrid fibres on crack arresting. The research results show that there is a positive synergy effect between large steel fibres and polypropylene fibres on the load bearing capacity in the small displacement range. But this synergy effect disappears in the large displacement range. The large and strong steel fibre is better than soft polypropylene fibre and small steel fibre in the aspect of energy absorption capacity in the large displacement range. The static usage limitation for the hybrid fibres concrete with “wide peak' or “multi peaks' load CMOD pattern should be carefully selected. The ultimate load bearing capacity and the crack width or CMOD at this load level should be jointly considered.

Interfacial microstructure and chemical stability during diffusion bonding of single crystal Al_2O_3-fibres with Ni25.8Al9.6Ta8.3Cr matrix

BN coated A1203 fibre-reinforced NiAl-alloy composites were fabricated by hot pressing at 1 200-1 400 ℃, and the interracial microstructure and chemical stability of BN coated Al2O3 fibre-reinforced NiAl-alloy composites were investigated by scanning electron microscopy （SEM） and analytical transmission electron microscopy （TEM）. It was found that the complicated chemical reactions and diffusion processes happened in the interface area between BN-layer and Ni25.8A19.6Ta8.3 during the hot pressing at 1 200-1 400 ℃. A continuous AlN-layer was formed at the interface due to the reaction between NiAl and BN. At the same time, Cr diffused extensively into the BN-layer and reacted with boron to form Cr boride precipitates （CrsB3）. In addition, a few particles of Ta-rich phase were also precipitated in NiAl matrix near the interface.

Orientation distribution of fibres in a channel flow of fibre suspension

The orientation and concentration distributions of fibres in laminar and turbulent channel flows are investigated numerically. The obtained results are in good agreement with the experimental data. In the laminar flow regime, more fibres orient to the flow direction as the Reynolds number increases. The shear rate of fluid around a fibre plays an important role in determining the orientation distribution of fibres, while the fibre density and the fibre aspect-ratio have marginal influence on the orientation distribution. In the turbulent regime, the orientation distribution of fibres becomes more homogeneous with the increase of Reynolds number, and the concentration profile is flatter than that in the laminar regime. The fluctuating intensity of fibre velocity in the downstream direction is larger than that in the lateral directions.

Influence of ultra-fine fly ash on hydration shrinkage of cement paste

Hydration shrinkage generated by cement hydration is the cause of autogenous shrinkage of high strength concrete. It may result in the volume change and even cracking of mortar and concrete. According to the data analysis in a series of experimental studies, the influence of ultra-fine fly ash on the hydration shrinkage of composite cementitious materials was investigated. It is found that ultra-fine fly ash can reduce the hydration shrinkage of cement paste effectively, and the more the ultra-fine fly ash, the less the hydration shrinkage. Compared with cement paste without the ultra-fine fly ash, the shrinkage ratio of cement paste reduces from 23.4% to 39.7% when the ultra-fine fly ash replaces cement from 20% to 50%. Moreover, the microscopic mechanism of the ultra-fine fly ash restraining the hydration shrinkage was also studied by scanning electron microscopy, X-ray diffraction and hydrated equations. The results show that the hydration shrinkage can be restrained to a certain degree because the ultra-fine fly ash does not participate in the hydration at the early stage and the secondary hydration products are different at the later stage.

Temperature dependence of birefringence in olarization-maintaining photonic crystal fibres

In this paper,the temperature dependence of birefringence in polarization maintaining photonic crystal fibres（PMPCFs） is investigated theoretically and experimentally.Utilizing the structural parameters of the PM-PCF samples in the experiment,two effects leading to the birefringence variation under different temperatures are analysed,which are the thermal expansion of silica material and the refractive index variation due to the temperature variation.The actual birefringence variation of the PM-PCF is the combination of the two effects,which is in the order of 10-9 K-1 for both fibre samples.Calculation results also show that the influence of refractive index variation is the dominant contribution,which determines the tendency of the fibre birefringence variation with varying temperature.Then,the birefringence beat lengths of the two fibre samples are measured under the temperature,which varies from -40℃ to 80℃.A traditional PANDA-type polarization maintaining fibre（PMF） is also measured in the same way for comparison.The experimental results indicate that the birefringence variation of the PM-PCF due to temperature variation is far smaller than that of the traditional PMF,which agrees with the theoretical analysis.The ultra-low temperature dependence of the birefringence in the PM-PCF has great potential applications in temperature-insensitive fibre interferometers,fibre sensors,and fibre gyroscopes.

Manufacturing Titanium Metal Matrix Composites by Consolidating Matrix Coated Fibres

Titanium metal matrix composites （TiMMCs） reinforced by continuous silicon carbide fibres are being developed for aerospace applications. TiMMCs manufactured by the consolidation of matrix-coated fibre （MCF） method offer optimum properties because of the resulting uniform fibre distribution, minimum fibre damage and fibre volume fraction control. In this paper, the consolidation of Ti-6Al-4V matrix-coated SiC fibres during vacuum hot pressing has been investigated. Experiments were carried out on multi-ply MCFs under vacuum hot pressing （VHP）. In contrast to most of existing studies, the fibre, arrangement has been carefully controlled either in square or hexagonal arrays throughout the consolidated sample. This has enabled the dynamic consolidation behaviour of MCFs to be demonstrated by eliminating the fibre re-arrangement during the VHP process. The microstructural evolution of the matrix coating was reported and the deformation mechanisms involved were discussed.