Ultra-wide band gap and wave attenuation mechanism of a novel star-shaped chiral metamaterial

A novel hollow star-shaped chiral metamaterial(SCM)is proposed by incorporating chiral structural properties into the standard hollow star-shaped metamaterial,exhibiting a wide band gap over 1500 Hz.To broaden the band gap,solid single-phase and two-phase SCMs are designed and simulated,which produce two ultra-wide band gaps(approximately 5116 Hz and 6027 Hz,respectively).The main reason for the formation of the ultra-wide band gap is that the rotational vibration of the concave star of two novel SCMs drains the energy of an elastic wave.The impacts of the concave angle of a single-phase SCM and the resonator radius of a two-phase SCM on the band gaps are studied.Decreasing the concave angle leads to an increase in the width of the widest band gap,and the width of the widest band gap increases as the resonator radius of the two-phase SCM increases.Additionally,the study on elastic wave propagation characteristics involves analyzing frequency dispersion surfaces,wave propagation directions,group velocities,and phase velocities.Ultimately,the analysis focuses on the transmission properties of finite periodic structures.The solid single-phase SCM achieves a maximum vibration attenuation over 800,while the width of the band gap is smaller than that of the two-phase SCM.Both metamaterials exhibit high vibration attenuation capabilities,which can be used in wideband vibration reduction to satisfy the requirement of ultra-wide frequencies.

ON THE PAR REDUCTION OF MB-OFDM ULTRA-WIDEBAND SIGNALS

The Peak to Average power Ratio (PAR) of a Multi-Band Orthogonal Frequency-Division Multiplexing (MB-OFDM) Ultra-Wide Band (UWB) signals can be substantially larger than that of single carrier or carrier-less ultra-wideband signals. In this letter, a novel PAR reduction scheme for the MB-OFDM UWB system based on spreading and interleaving is proposed. By spreading the coded bits over each subcarrier in corresponding band and interleaving the spread symbols across all bands, the PAR statistics of the MB-OFDM signals can be improved and the PAR is reduced obviously. In the PAR reduction scheme, there is no loss in transmission data rate or Bit Error Rate (BER) performance decreasing. Since the spreading and interleaving operation are implemented by unitary Hadamard sequences and used for an approach to provide the robustness of the UWB system to narrowband interference, there is no additional implementation burden. Simulation results show that the investigated scheme gives the PAR reduction of 3dB compared with that of the original MB-OFDM signals.

Mathematical Formulations of Signal Propagation in Ultra-Wideband Transceiver Systems under a UWB Channel Environment with an Extension of Frequency Offset Correction

This paper analyzes mathematically the crucial aspects of signal processing in a Multi-Band (MB) Orthogonal Frequency Division Multiplexing (OFDM) based system considering Ultra-Wideband (UWB) channel environment. In the process of analysis, it emphasizes the significant features of UWB receiver design in comparison with ‘conventional’ narrow-band system. The analysis shows that the high dispersive nature of a frequency selective UWB channel effects the design of different signal processing blocks like pre-select filter, low noise amplifier (LNA) and analog-to-digital (A/D) converter in the receiver front end. The characteristic functions of each of these stages are now dominated by the channel characteristics and it needs to be modified accordingly. This analysis is extended further with the study of frequency offset error and its correction. The unbiased Cramer Rao Lower Bound (CRLB) of estimation error is calculated and supported by computer simulation. The performance of an MB-OFDM system with frequency offset correction in terms of Bit-Error-Rate (BER) is also reported.

Evaluation of System Performance of Ultra-Wide Band Jointing in MC Signaling in Correlated Environments

The evaluation of System Performance of UWB (ultra-wide band) jointing in MC (multi-carrier) signaling in correlated environments is presented in the report. The correlated Nakagami-m statistical distribution for the multipath fading model is assumed in this scenario. In fact to establish the model for analyzing in this article is using MC-CDMA (multi-carrier code-division multiple-access) system characterization combined with a UWB scheme. The average BER (bit error rate) is calculated and compared to a special case of previously published results. Studied results from this paper can be implied to approve the system performance for a UWB system combined with a MC-CDMA wireless communication system. It is worth noting that the Nakagami-m distributed fading parameter significantly dominates UWB system performance when it cooperates with MC signaling under a fading environment. Finally, it is worthy of noting that when the SNR (signal-to-noise ratio) at system’s receiver reaches a preset high threshold value, the parameter of power decay ratio effect could be not included.

Compact Coplanar Epsilon-Negative Antenna with Ultra-Wide Band Character

In this paper, a compact coplanar epsilon.negative(ENG) antenna is proposed with ultra.wide operation band and small size of 18×11.5 mm2. The proposed antenna is designed based on a coplanar.waveguide(CPW) feeding antenna, and thus the via.free structure is employed to realize the ENG unit cell, which is convenient to tune the frequency of zeroth.order resonance(ZOR) and extends the ZOR bandwidth. The high.order resonant frequencies are achieved and mainly determined by the separate slots that are located between the radiating patch and the ground plane. Adding the left.handed inductance between the radiating patch and ground has slight impact on the high.order resonant frequencies, and then the ultra.wide band is achieved by merging the ZOR bandwidth with the high.order resonant bandwidths. The ground plane primarily works as a matching network for the proposed antenna. Although it generates a low.frequency resonance, the performance is undesirable due to the impedance mismatching. The measured results show that the reflection coefficient, |S11| <.10 d B, is in a wide frequency range from 5.25 to 13 GHz, which covers the upper operation band of UWB communication. Also, the antenna contains relatively stable gains and omni.directional radiation patterns.

Numerical simulation of the coupling of ultra-wide band electromagnetic pulse into landmine by aperture

The modern landmine＇s electronic fuse is susceptible to strong interference or can even be damaged by the ultra-wide band electromagnetic pulse（UWB-EMP）. The finite-difference time-domain（FDTD） method in lossy media with cylindrical coordinates is used to study the interactions of the UWB-EMP with the landmine. First, the coupling of UWB-EMP into the landmine shielding shell through an aperture is numerically simulated. Second, the coupled electromagnetic field of mine shells made of different shielding materials and with apertures of different sizes is plotted. Third, the aperture coupling laws of UWB-EMP into shells are analyzed and categorized. Such an algorithm is capable of effectively preventing ladder similar errors, and consequently improving the calculation precision, and in addition to adopting the message passing interface（MPI） parallel method to divide the total calculating range into more sub-ranges, the overall calculating efficiency is greatly increased. These calculations are surely a constructive reference for modern landmine design against electromagnetic damage.

Mobile Robot Positioning and Tracking Based on Ultra-wideband Technology

To solve the precision self-positioning problem for mobile robot,a positioning program based on ultra-wideband technology was proposed. Ultra-wideband pulse has very high bandwidth; ranging accuracy can achieve centimeter-level theoretically. The mobile robot obtained the distance to the reference node by sending ultra-wideband pulse. According to the geometric relations among the references and the robot,establish equations to calculate the position coordinates. Then Kalman filter algorithm was applied for mobile robot tracking. Simulation results show that robot positioning and tracking based on ultra-wideband technology can achieve indoor and outdoor seamless docking.

Designing a Carbon Nanotube Field-Effect Transistor with High Transition Frequency for Ultra-Wideband Application

Theoretical calculations predict transition frequencies in the terahertz range for the field-effect transistors based on carbon nanotubes, and this shows their suitability for being used in high frequency applications. In this paper, we have designed a field-effect transistor based on carbon nanotube with high transition frequency suitable for ultra-wide band applications. We did this by optimizing nanotube diameter, gate insulator thickness and dielectric constant. As a result, we achieved the transition frequency about 7.45 THz. The environment of open source software FETToy is used to simulate the device. Also a suitable model for calculating the transition frequency is presented.

ULTRAWIDE BAND RADAR SIGNAL DETECTION, ESTIMATION AND EXPERIMENT

With reference to the air target detection of ultra-wide band (UWB)/impulse radar(IR), the transient signal processing techniques was discussed. In weak UWB signal detection, the wavelet transforms and high order spectrum estimation techniques were preferred. In target characteristic analysis, a time domain bispectrum estimation algorithm was used to analyze the target impulse response, which could estimate accurately local scattering distribution of complex target. A free field IR experimental system installed in an anechoic chamber was used. With this system, experiments to several target models were made. The results of these experiments verified the signal processing method efficiency.

PIM Interference Analysis under Multi-band Multi-signal Input in Duplex Indoor Distribution System

This analysis focuses on PIM interference under multi-band multi-signal input in mobile communication system.Unlike single band system that only odd order PIM(especially 3rd order) should be concerned,in multi-band multi-signal case,both odd and even order PIM could be interference source because of more complicated intermodulation,more IMPs generated and more receive bands.Especially,the 2nd order PIM may interfere more serious to receiving channel for its strong magnitude.In duplex indoor distribute system,the PIM interference is a potential problem to GSM900,DCS1800,CDMA,and even 3G system wireless services,because the PIM frequencies may fall in receive bands and interfere to the receiving channels.In radio system design and wireless channel assignment,precautions must be taken to minimize the PIM level and to avoid interfere to receiving channels.For practical use,the lower order possible PIM interference to 2G and 3G systems is calculated.

基于多载波调制技术的无线短波通信多频段信号增强研究

在现代无线通信系统中,多载波调制技术由于其高效的频谱利用和强大的信号处理能力,成为实现可靠通信的关键技术之一。这项技术特别适用于复杂的短波通信环境,其中信号容易受到多路径效应和频率选择性衰落的影响。文章综合研究了多载波调制技术在无线短波通信中的应用,并提出了一系列信号增强措施,包括多载波调制参数的优化、多频段信号的同步与校准、功率控制与信号优化的集成技术以及针对频段拥堵的动态频率分配策略。此外,文章还通过技术应用测试验证了这些策略的有效性,结果显示这些策略能显著提升短波通信系统的性能和可靠性。

基于MAXBAND和VISSIM的交通管理与控制信号绿波实验设计

为了促进学生更直观地理解信号绿波的控制原理和效果,基于MAXBAND模型和VISSIM软件系统性地构建了干线信号绿波的实验方案。实验包括绿波相位差的确定、绿波控制方案的仿真模拟和控制方案评价分析3个步骤,可帮助学生理解绿波协调、交通流量、相位结构等因素对干线交通运行状况的影响,从而培养学生使用现代化的工具分析和解决交通控制问题的能力。

A Novel UWB Signal Sampling Method for Localization based on Compressive Sensing

Ultra-wide-band (UWB) signals are suitable for localization, since their high time resolution can provide precise time of arrival (TOA) estimation. However, one major challenge in UWB signal processing is the requirement of high sampling rate which leads to complicated signal processing and expensive hardware. In this paper, we present a novel UWB signal sampling method called UWB signal sampling via temporal sparsity (USSTS). Its sampling rate is much lower than Nyquist rate. Moreover, it is implemented in one step and no extra processing unit is needed. Simulation results show that USSTS can not recover the signal precisely, but for the use in localization, the accuracy of TOA estimation is the same as that in traditional methods. Therefore, USSTS gives a novel and effective solution for the use of UWB signals in localization.

PERFORMANCE OF NON-COHERENT RECEIVER WITH UWB PPM SIGNAL IN MULTIPATH CHANNELS

Mainly due to its implementation simplicity, the non-coherent Ultra-Wide Band (UWB) receiver is attractive for lower data rate applications, which gains much attention again in recent years. In this paper, a General Likelihood Ratio Test (GLRT) based non-coherent receiver on UWB Pulse-Position-Modulation (PPM) signal in multipath channels is derived, and a novel structure is proposed as well. Subsequently, the closed-form expressions of asymptotic error-rate performance related to the non-coherent receiver are also derived and verified.

The measurement of sea surface profile with X-band coherent marine radar

The line-of-sight velocity of scattering facets is related to the Doppler signals of X-band coherent marine radar from the oceanic surface. First, the sign Doppler Estimator is applied to estimate the Doppler shift of each radar resolution cell. And then, in terms of the Doppler shift, a retrieval algorithm extracting the vertical displacement of the sea surface has been proposed. The effects induced by radar look-direction and radar spatial resolution are both taken into account in this retrieval algorithm. The comparison between the sea surface spectrum of buoy data and the retrieved spectrum reveals that the function of the radar spatial resolution is equivalent to a low pass filter, impacting especially the spectrum of short gravity waves. The experimental data collected by McMaster IPIX radar are also used to validate the performance of the retrieval algorithm. The derived significant wave height and wave period are compared with the in situ measurements, and the agreement indicates the practicality of the retrieval technology.

Linear Prolate Functions for Signal Extrapolation with Time Shift

We propose a low complexity iterative algorithm for band limited signal extrapolation. The extrapolation method is based on the decomposition of finite segments of the signal via truncated series of real-valued linear prolate functions. Our theoretical derivation shows that given a truncated series (up to a selectable value) of prolate functions, it is possible to extrapolate the band limited function elsewhere if each extrapolated portion of the function is subject only to moderate truncation errors that we quantify in this paper. The effects of different sources of errors have been analyzed via extensive simulations. We have investigated a property of the signal decomposition formula based on linear prolate functions whereby the integration interval does not need to be symmetric with respect to the origin while time-shifted prolate functions are used in the series.

A HOS-based Blind Signal Extraction Method for Chaotic MIMO Systems

A novel method to extract multiple input and multiple output (MIMO) chaotic signals was proposed using the blind neural algorithm after transmitting in nonideal channel. The MIMO scheme with different chaotic signal generators was presented. In order to separate the chaotic source signals only by using the sensor signals at receivers, a blind neural extraction algorithm based on higher-order statistic (HOS) technique was used to recover the primary chaotic signals. Simulation results show that the proposed approach has good performance in separating the primary chaotic signals even under nonideal channel.

Simplified calculation of UWB signal transmitting through a finitely conducting slab

A simplified closed-form analytic solution for UWB impulse signal transmitting through a finitely conducting slab is proposed. The approach first requires evaluating the impulse response of the slab and then convolving it with the specified incident field waveform. To obtain the impulsive transmitting field, either for vertical or horizontal polarization, approximations to the refraction coefficients and propagation loss are made, which can be proved to be accurate enough, comparing with their frequency domain solutions. Thereby, it permits simplified closed-form expressions in the time domain for both terms. The resulting transient response for the transmitting impulse field is then given by convolution of the time domMn refraction coefficients and time domain propagation loss. A numerical example of an incident monocyele transmitting through a slab using this technique, is presented, to illustrate the effective use of the method.

Angular insensitive nonreciprocal ultrawide band absorption in plasma-embedded photonic crystals designed with improved particle swarm optimization algorithm

Using an improved particle swarm optimization algorithm(IPSO)to drive a transfer matrix method,a nonreciprocal absorber with an ultrawide absorption bandwidth and angular insensitivity is realized in plasma-embedded photonic crystals arranged in a structure composed of periodic and quasi-periodic sequences on a normalized scale.The effective dielectric function,which determines the absorption of the plasma,is subject to the basic parameters of the plasma,causing the absorption of the proposed absorber to be easily modulated by these parameters.Compared with other quasi-periodic sequences,the Octonacci sequence is superior both in relative bandwidth and absolute bandwidth.Under further optimization using IPSO with 14 parameters set to be optimized,the absorption characteristics of the proposed structure with different numbers of layers of the smallest structure unit N are shown and discussed.IPSO is also used to address angular insensitive nonreciprocal ultrawide bandwidth absorption,and the optimized result shows excellent unidirectional absorbability and angular insensitivity of the proposed structure.The impacts of the sequence number of quasi-periodic sequence M and collision frequency of plasma1ν1 to absorption in the angle domain and frequency domain are investigated.Additionally,the impedance match theory and the interference field theory are introduced to express the findings of the algorithm.

Compact Bluetooth/UWB Antenna with Multi-Band Notched Characteristics

A small-sized, low-profile, and planar dual band antenna for Bluetooth (2.4 - 2.484 GHz) and ultra-wideband (UWB) (3.1 - 10.6 GHz) with multi-band notched antennas is presented. Two antennas A and B with different types of slots are used to obtain tri-band notched characteristic. In antenna A notched bands, 5 - 6 GHz for WLAN, and 3.3 - 4 GHz for WiMAX, are achieved using a U-slot in ground structure and in the radiating patch. In antenna B two notched bands at 3.3 - 4 GHz, for WiMAX and 7.2 GHz for C-band satellite communication systems are achieved by using a U-slot in ground structure and a H-shaped slot in the radiating patch. The radiation characteristics of the two antennas are calculated using a commercial EM simulator based on Finite Element Method (FEM) and the Finite Integration Technique (FIT). The two antennas show acceptable gain flatness with stable omnidirectional radiation patterns across the integrated Bluetooth and UWB bands.