Cake models applied to evaluate the fouling mechanism in separation of anionic polyacrylamide using modified PVDF ultrafiltration membranes

In the present study,nano-sized TiO2 /Al2O3 modified PVDF membranes (MM) were fabricated and utilized for anionic polyacrylamide ( APAM) separation. The results showed that,compared with PVDF membrane (OM) ,the contact angle of MM decreases from 83. 64° to 67. 42°,which indicates the increase of the hydrophilicity of MM. The relative flux (RF) decline curve of this ultrafiltration of APAM in water with time shows an obvious two stage properties. The cake filtration models were used to predict the performance of different time over the complete range of filtration times. All the four cake models could simulate this UF process to a certain extent,and the suitability of the two kinds of membranes was: cake filtration > intermediate pore blocking > standard pore blocking > complete pore blocking models. However,they became more and more unsuited to this process with time extending. Surface and cross-sectional morphology of membrane was investigated by SEM to make an advanced certificate of this UF mechanism.

Operating Conditions Optimization on Indonesian ＂Batik＂ Dyes Wastewater Treatment by Fenton Oxidation and Separation Using Ultrafiltration Membrane

Broadly speaking, this study aims to develop ＂batik＂ dyes wastewater treatment technologies by hybrid process that combines Fenton oxidation and separation using ultrafiltration membranes. Specifically, the purpose of this study was to determine the effect of membrane characteristics, feed solution pH, operating pressure of ＂Dead-end＂ membrane reactor, and the frequency of membranes which uses on the percentage of COD reduction in ＂batik＂ wastewater. In this study, the filtrate from wastewater pre-treatment with Fenton oxidation, both without and with addition of activated carbon, is passed to the ultrafiltration （UF） separation system. Fenton oxidation process was carried out at optimum conditions, i.e. at pH 3, temperature 50 ℃, and the addition FeSO4·7H2O and H2O2 at 747-830 mg/L and 1,168-1,460 mg/L, respectively. The optimum reduction percentage of COD can be achieved when the membranes used for separation has a pore size of 0.01 to 0.015 lam, feed solution pH 2, operating pressure 1 atm and frequency of membranes uses I x. To determine the fouling potential on ultrafiltration membranes that are used, flux measurements were performed 3 times for each membrane. These stages can see that the flux decline reached 22.5% when the effluent filtered directly to the membrane; 17.3% when performed pre-treatment prior to separation processes using membranes and 10% when combined pre-treatment process, use of activated carbon and the separation using ultrafiltration membranes.

Deep eutectic solvents for separation and purification applications in critical metal metallurgy:Recent advances and perspectives

Solvent extraction,a separation and purification technology,is crucial in critical metal metallurgy.Organic solvents commonly used in solvent extraction exhibit disadvantages,such as high volatility,high toxicity,and flammability,causing a spectrum of hazards to human health and environmental safety.Neoteric solvents have been recognized as potential alternatives to these harmful organic solvents.In the past two decades,several neoteric solvents have been proposed,including ionic liquids(ILs)and deep eutectic solvents(DESs).DESs have gradually become the focus of green solvents owing to several advantages,namely,low toxicity,degradability,and low cost.In this critical review,their classification,formation mechanisms,preparation methods,characterization technologies,and special physicochemical properties based on the most recent advancements in research have been systematically described.Subsequently,the major separation and purification applications of DESs in critical metal metallurgy were comprehensively summarized.Finally,future opportunities and challenges of DESs were explored in the current research area.In conclusion,this review provides valuable insights for improving our overall understanding of DESs,and it holds important potential for expanding separation and purification applications in critical metal metallurgy.

High performance photodegradation resistant PVA@TiO_(2)/carboxyl-PES self-healing reactive ultrafiltration membrane

The occurrence of ultrafiltration(UF)membrane fouling frequently hampers the sustainable advancement of UF technology.Reactive self-cleaning UF membranes can effectively alleviate the problem of membrane fouling.Nevertheless,the self-cleaning process may accelerate membrane aging.Addressing these concerns,we present an innovative design concept for composite self-healing materials based on self-cleaning UF membranes.To begin,TiO_(2)nanoparticles were incorporated into the polymer molecular structure via molecular design,resulting in the synthesis of TiO_(2)/carboxyl-polyether sulfone(PES)hybrid materials.Subsequently,the nonsolvent-induced phase inversion technique was employed to prepare a novel of UF membrane.Lastly,a polyvinyl alcohol(PVA)hydrogel coating was applied to the hybrid UF membrane surface to create PVA@TiO_(2)/carboxyl-PES self-healing reactive UF membranes.By establishing a covalent bond,the TiO_(2)nanoparticles were effectively and uniformly dispersed within the UF membrane,leading to exceptional self-cleaning properties.Furthermore,the water-absorbing and swelling properties of PVA hydrogel,along with its capacity to form hydrogen bonds with water molecules,resulted in UF membranes with improved hydrophilicity and active self-healing abilities.The results demonstrated that the water contact angle of PVA@5%TiO_(2)/carboxyl-PES UF membrane was 43.1°.Following a 1-h exposure to simulated solar exposure,the water flux recovery ratio increased from 48.16%to 81.03%.Moreover,even after undergoing five cycles of 12-h simulated sunlight exposure,the UF membranes exhibited a consistent retention rate of over 97%,thus fully demonstrating their exceptional self-cleaning,antifouling,and selfhealing capabilities.We anticipate that the self-healing reactive UF membrane system will serve as a pioneering and comprehensive solution for the self-cleaning antifouling challenges encountered in UF membranes while also effectively mitigating the aging effects of reactive UF membranes.

Role of tannin pretreatment in flotation separation of magnesite and dolomite

Flotation separation of magnesite and its calcium-containing carbonate minerals is a difficult problem.Recently,new regulat-ors have been proposed for magnesite flotation decalcification,although traditional regulators such as tannin,water glass,sodium carbon-ate,and sodium hexametaphosphate are more widely used in industry.However,they are rarely used as the main regulators in research because they perform poorly in magnesite and dolomite single-mineral flotation tests.Inspired by the limonite presedimentation method and the addition of a regulator to magnesite slurry mixing,we used a tannin pretreatment method for separating magnesite and dolomite.Microflotation experiments confirmed that the tannin pretreatment method selectively and largely reduces the flotation recovery rate of dolomite without affecting the flotation recovery rate of magnesite.Moreover,the contact angles of the tannin-pretreated magnesite and dolomite increased and decreased,respectively,in the presence of NaOl.Zeta potential and Fourier transform infrared analyses showed that the tannin pretreatment method efficiently hinders NaOl adsorption on the dolomite surface but does not affect NaOl adsorption on the magnesite surface.X-ray photoelectron spectroscopy and density functional theory calculations confirmed that tannin interacts more strongly with dolomite than with magnesite.

Phase separation and transcriptional regulation in cancer development

Liquid-liquid phase separation,a novel biochemical phenomenon,has been increasingly studied for its medical applications.It underlies the formation of membrane-less organelles and is involved in many cellular and biological processes.During transcriptional regulation,dynamic condensates are formed through interactions between transcriptional elements,such as transcription factors,coactivators,and mediators.Cancer is a disease characterized by uncontrolled cell proliferation,but the precise mechanisms underlying tumorigenesis often remain to be elucidated.Emerging evidence has linked abnormal transcriptional condensates to several diseases,especially cancer,implying that phase separation plays an important role in tumorigenesis.Condensates formed by phase separation may have an effect on gene transcription in tumors.In the present review,we focus on the correlation between phase separation and transcriptional regulation,as well as how this phenomenon contributes to cancer development.

Advances in depressants for flotation separation of Cu–Fe sulfide minerals at low alkalinity:A critical review

The flotation separation of Cu–Fe sulfide minerals at low alkalinity can be achieved using selective depressants.In the flotation system of Cu–Fe sulfide minerals,depressants usually preferentially interact with the pyrite surface to render the mineral surface hydrophilic and hinder the adsorption of the collector.This review summarizes the advances in depressants for the flotation separation of Cu–Fe sulfide minerals at low alkalinity.These advances include use of inorganic depressants (oxidants and sulfur–oxygen compounds),natural polysaccharides (starch,dextrin,konjac glucomannan,and galactomannan),modified polymers (carboxymethyl cellulose,polyacrylamide,lignosulfonate,and tricarboxylate sodium starch),organic acids (polyglutamic acid,sodium humate,tannic acid,pyrogallic acid,salicylic acid,and lactic acid),sodium dimethyl dithiocarbamate,and diethylenetriamine.The potential application of specific inorganic and organic depressants in the flotation separation of Cu–Fe sulfide minerals at low alkalinity is reviewed.The advances in the use of organic depressants with respect to the flotation separation of Cu–Fe sulfide minerals are comprehensively detailed.Additionally,the depression performances and mechanisms of different types of organic depressants on mineral surfaces are summarized.Finally,several perspectives on depressants vis-à-vis flotation separation of Cu–Fe sulfide minerals at low alkalinity are proposed.

Recent progress in ternary mixed matrix membranes for CO_(2) separation

Mixed matrix membranes(MMMs)could combine the advantages of both polymeric membranes and porousfillers,making them an effective alternative to conventional polymer membranes.However,interfacial incompatibility issues,such as the presence of interfacial voids,hardening of polymer chains,and blockage of micropores by polymers between common MMMsfillers and the polymer matrix,currently limit the gas sep-aration performance of MMMs.Ternary phase MMMs(consisting of afiller,an additive,and a matrix)made by adding a third compound,usually functionalized additives,can overcome the structural problems of binary phase MMMs and positively impact membrane separation performance.This review introduces the structure and fabrication processes for ternary MMMs,categorizes various nanofillers and the third component,and summarizes and analyzes in detail the CO_(2) separation performance of newly developed ternary MMMs based on both rubbery and glassy polymers.Based on this separation data,the challenges of ternary MMMs are also discussed.Finally,future directions for ternary MMMs are proposed.

Recent developments in asphalt-aggregate separation technology for reclaimed asphalt pavement

Reclaimed asphalt pavement(RAP)has significant recycling value because it contains nonrenewable resources including asphalt and aggregate.However,thus far,only a small part of RAP materials can be used in the con-struction of recycled asphalt pavement,and the usage is regarded as a low-value utilization in the underlying layers.One of the most important reasons for this shortcoming is the problem of false particle size and pseudo gradation of RAP materials.Therefore,identifying suitable asphalt-aggregate separation technology is essential for improving the utilization of RAP materials in recycled asphalt mixture and enhancing the construction quality of recycled asphalt pavement.To address this,the paper performed a systematic review of asphalt-aggregate separation technologies for processing RAP materials and their prospects.Firstly,based on the composition of the asphalt mixture and the characteristics of RAP materials after aging,the key RAP separation technologies were proposed.Then,the concept,principle,and implementation methods of physical,chemical,and biological sep-aration methods of RAP materials were comprehensively analyzed.Moreover,the advantages and disadvantages of various separation technologies were discussed by comparing them with the related technologies in the petrochemical industry.The application prospects of various asphalt-aggregate separation methods for RAP materials can provide a reference for upgrading and expanding solid waste recycling technology for asphalt pavement.

Selective adsorption of tetracycline by β-CD-immobilized sodium alginate aerogel coupled with ultrafiltration for reclaimed water

In this work,a novel composite material based on β-cyclodextrin-immobilized sodium alginate aerogel(β-CD/NaAlg) was developed utilizing cross-linker of epichlorohydrin and applied as an adsorbent to remove tetracycline antibiotics from reclaimed wastewater.A series of characterizations were utilized to confirm the successful synthesis of the adsorbent and this β-CD/NaAlg presented a three-dimensional network at the nanoscale or microscale.Under optimal conditions(pH=4,t=8 h,β-CD:NaAlg=9,adsorbent dosage = 1.5 g·L-1),the maximum removal rate of β-CD/NaAlg to tetracycline was 70%.The adsorption behavior of tetracycline on β-CD/NaAlg conformed to the Freundlich isotherm model(R2=0.9977) and the pseudo-second-order kinetic model(R^(2)=0.9993).Moreover,the adsorbent still removed 55.3% of tetracycline after five cycles.Specially,the adsorbent was integrated with ultrafiltration to adsorb tetracycline antibiotics from simulated reclaimed wastewater,and the removal rate of tetracycline reached 78.9% within 2 h.The existence of Cr(Ⅵ) had a negligible impact on tetracycline removal,while the presence of humic acid exhibited a promoting effect.The possible adsorption mechanisms were also elucidated through X-ray photoelectron spectroscopy and density functional theory analysis.In summary,β-CD/NaAlg represents an environmentally friendly,efficient,and sustainable adsorbent for removing tetracycline antibiotics from reclaimed water.

Flotation separation of brucite and calcite in dodecylamine system enhanced by regulator potassium dihydrogen phosphate

To achieve efficient flotation separation of brucite and calcite,flotation separation experiments were conducted on two minerals using dodecylamine(DDA)as the collector and potassium dihydrogen phosphate(PDP)as the regulator.The action mechanism of DDA and PDP was explored through contact angle measurement,zeta potential detection,solution chemistry calculation,FTIR analysis,and XPS detection.The flotation results showed that when DDA dosage was 35 mg/L and PDP dosage was 40 mg/L,the maximum floating difference between brucite and calcite was 79.81%,and the selectivity separation index was 6.46.The detection analysis showed that the main dissolved component HPO_(4)^(2−)of PDP is selectively strongly adsorbed on the Ca site on the surface of calcite,promoting the adsorption of the main dissolved component RNH_(3)^(+)of DDA on calcite surface,while brucite is basically not affected by PDP.Therefore,PDP is an effective regulator for the reverse flotation separation of brucite and calcite in DDA system.

Preparation of a zeolite-palladium composite membrane for hydrogen separation:Influence of zeolite film on membrane stability

With the development of hydrogen energy,palladium-based membranes have been widely used in hydrogen separation and purification.However,the poor chemical stability of palladium composite membranes limits their commercial applications.In this study,a zeolite-palladium composite membrane with a sandwich-like structure was obtained by using a TS-1 zeolite film grown on the surface of palladium membrane.The membrane microstructure was characterized by SEM and EDX.The effects of the TS-1 film on the hydrogen permeability and stability of palladium composite membrane were investigated in details.Benefited from the protection of the TS-1 zeolite film,the stability of palladium composite membrane was enhanced.The results indicate that the TS-1-Pd composite membrane was stable after eight cycles of the temperature exchange cycles between 773 K and 623 K.Especially,the loss of hydrogen permeance for TS-1-Pd composite membrane was much smaller than that of the pure palladium membrane when the membrane was tested in the presence of C3H6atmosphere.It indicated that the TS-1-Pd composite membrane had better chemical stability in comparison with pure palladium membrane,owing to its sandwich-like structure.This work provides an efficient way for the deposition of zeolite film on palladium membrane to enhance the membrane stability.

Ferric ion-triggered surface oxidation of galena for efficient chalcopyrite-galena separation

The efficient separation of chalcopyrite(CuFeS2)and galena(PbS)is essential for optimal resource utilization.However,find-ing a selective depressant that is environmentally friendly and cost effective remains a challenge.Through various techniques,such as mi-croflotation tests,Fourier transform infrared spectroscopy,scanning electron microscopy(SEM)observation,X-ray photoelectron spec-troscopy(XPS),and Raman spectroscopy measurements,this study explored the use of ferric ions(Fe^(3+))as a selective depressant for ga-lena.The results of flotation tests revealed the impressive selective inhibition capabilities of Fe^(3+)when used alone.Surface analysis showed that Fe^(3+)significantly reduced the adsorption of isopropyl ethyl thionocarbamate(IPETC)on the galena surface while having a minimal impact on chalcopyrite.Further analysis using SEM,XPS,and Raman spectra revealed that Fe^(3+)can oxidize lead sulfide to form compact lead sulfate nanoparticles on the galena surface,effectively depressing IPETC adsorption and increasing surface hydrophilicity.These findings provide a promising solution for the efficient and environmentally responsible separation of chalcopyrite and galena.

A novel molybdenite depressant for efficient selective flotation separation of chalcopyrite and molybdenite

A novel small molecule depressant(M-DEP)was used to separate chalcopyrite and molybdenite via flotation.The results showed that M-DEP had an excellent selective depression on molybdenite,while had little effect on the flotation of chalcopyrite.The adsorption capacity of M-DEP on the surface of molybdenite was greater than that on chalcopyrite surface.The adsorption of M-DEP reduced the floatability of molybdenite and had less effect on the floatability of chalcopyrite,which was due to its different adsorption modes on the surface of the two minerals.Furthermore,the interaction between chalcopyrite and M-DEP was mainly chemical interaction,and almost all of the adsorbed M-DEP molecules were removed and replaced by sodium butyl xanthate(SBX).By contrast,hydrophobic interaction was the main way in which M-DEP was adsorbed on the molybdenite surface with little chemical interaction,which was less interfered by SBX addition.Therefore,M-DEP had a super selective depression on molybdenite.The study provided a novel depressant and approach for the deep separation of chalcopyrite and molybdenite via flotation.

New process for treating boron-bearing iron ore by flash reduction coupled with magnetic separation

Boron is an important industrial raw material often sourced from minerals containing different compounds that cocrystallize,which makes it difficult to separate the mineral phases through conventional beneficiation.This study proposed a new treatment called flash reduction-melting separation(FRMS)for boron-bearing iron concentrates.In this method,the concentrates were first flash-reduced at the temperature under which the particles melt,and the slag and the reduced iron phases disengaged at the particle scale.Good reduc-tion and melting effects were achieved above 1550℃.The B_(2)O_(3) content in the separated slag was over 18wt%,and the B content in the iron was less than 0.03wt%.The proposed FRMS method was tested to investigate the effects of factors such as ore particle size and tem-perature on the reduction and melting steps with and without pre-reducing the raw concentrate.The mineral phase transformation and morphology evolution in the ore particles during FRMS were also comprehensively analyzed.

Multiple roles of arsenic compounds in phase separation and membraneless organelles formation determine their therapeutic efficacy in tumors

Arsenic compounds are widely used for the therapeutic intervention of multiple diseases.Ancient pharmacologists discovered the medicinal utility of these highly toxic substances,and modern pharmacologists have further recognized the specific active ingredients in human diseases.In particular,Arsenic trioxide(ATO),as a main component,has therapeutic effects on various tumors(including leukemia,hepatocellular carcinoma,lung cancer,etc.).However,its toxicity limits its efficacy,and controlling the toxicity has been an important issue.Interestingly,recent evidence has pointed out the pivotal roles of arsenic compounds in phase separation and membraneless organelles formation,which may determine their toxicity and therapeutic efficacy.Here,we summarize the arsenic compoundsregulating phase separation and membraneless organelles formation.We further hypothesize their potential involvement in the therapy and toxicity of arsenic compounds,highlighting potential mechanisms underlying the clinical application of arsenic compounds.

Anti-abrasion collagen fiber-based membrane functionalized by UiO-66-NH_(2)with ultra-high efficiency and stability for oil-in-water emulsions separation

Membrane separation strategies offer promising platform for the emulsion separation.However,the low mechanical strength of membrane separation layers and the trade-off between separation flux and efficiency present significant challenges.In this study,we report a CFM@UiO-66-NH_(2)membrane with high separation flux,efficiency and stability,through utilizing a robust anti-abrasion collagen fiber membrane(CFM)as the multifunctional support and UiO-66-NH_(2)by an in-situ growth as the separation layer.The high mechanical strength of the CFM compensated for the weakness of the separation layer,while the charge-breaking effect of UiO-66-NH_(2),along with the size sieving of its constituent separating layers and the capillary effect of the collagen fibers,contributed to the potential for efficient separation.Additionally,the CFM@UiO-66-NH_(2)membrane exhibited superhydrophilic properties,making it suitable for separating oil-in-water microemulsions and nanoemulsions stabilized by anionic surfactants.The membrane demonstrated remarkable separation efficiencies of up to 99.960%and a separation flux of370.05 L·m^(-2)·h^(-1).Moreover,it exhibits stability,durability,and abrasion resistance,maintaining excellent separation performance even when exposed to strong acids and alkalis without any damage to its structure and performance.After six cycles of reuse,it achieved a separation flux of 417.97 L·m^(-2)·h^(-1)and a separation efficiency of 99.747%.Furthermore,after undergoing 500 cycles of strong abrasion,the separation flux remained at 124.39 L·m^(-2)·h^(-1),with a separation efficiency of 99.992%.These properties make it suitable for the long-term use in harsh operating environments.We attribute these properties to the electrostatic effect resulting from the amino group on UiO-66-NH_(2)and its in-situ growth on the CFM,which forms a size-screening separation layer.Our work highlights the potential of the CFM@UiO-66-NH_(2)membrane as an environmentally friendly size-screening material for the efficient emulsion wastewater separation.

Boosting kinetic separation of ethylene and ethane on microporous materials via crystal size control

The adsorptive separation of C_(2)H_(4)and C_(2)H_(6),as an alternative to distillation units consuming high energy,is a promising yet challenging research.The great similarity in the molecular size of C_(2)H_(4)and C_(2)H_(6)brings challenges to the regulation of adsorbents to realize efficient dynamic separation.Herein,we reported the enhancement of the kinetic separation of C_(2)H_(4)/C_(2)H_(6)by controlling the crystal size of ZnAtzPO_(4)(Atz=3-amino-1,2,4-triazole)to amplify the diffusion difference of C_(2)H_(4)and C_(2)H_(6).Through adjusting the synthesis temperature,reactant concentration,and ligands/metal ions molar ratio,ZnAtzPO4 crystals with different sizes were obtained.Both single-component kinetic adsorption tests and binary-component dynamic breakthrough experiments confirmed the enhancement of the dynamic separation of C_(2)H_(4)/C_(2)H_(6)with the increase in the crystal size of ZnAtzPO_(4).The separation selectivity of C_(2)H_(4)/C_(2)H_(6)increased from 1.3 to 98.5 with the increase in the crystal size of ZnAtzPO_(4).This work demonstrated the role of morphology and size control of adsorbent crystals in the improvement of the C_(2)H_(4)/C_(2)H_(6)kinetic separation performance.

Superhydrophobic melamine sponge prepared by radiation-induced grafting technology for efficient oil-water separation

This paper presents a superhydrophobic melamine(ME)sponge(ME-g-PLMA)prepared via high-energy radiation-induced in situ covalent grafting of long-alkyl-chain dodecyl methacrylate(LMA)onto an ME sponge for efficient oil–water separation.The obtained ME-g-PLMA sponge had an excellent pore structure with superhydrophobic(water contact angle of 154°)and superoleophilic properties.It can absorb various types of oils up to 66–168 times its mass.The ME-g-PLMA sponge can continuously separate oil slicks in water by connecting a pump or separating oil underwater with a gravity-driven device.In addition,it maintained its highly hydrophobic properties even after long-term immersion in different corrosive solutions and repeated oil adsorption.The modified ME-g-PLMA sponge exhibited excellent separation properties and potential for oil spill cleanup.

A novel surfactant N-hydroxy-9,10-epoxy group-octadecanamide:Part II.Its synthesis and application in flotation separation of spodumene and albite

A novel hydroxamic acid,N-hydroxy-9,10-epoxy group-octadecanamide(N-OH-9,10-O-ODA),was synthesised by modifying the structure of oleic acid.The carboxyl group of oleic acid was converted into an N-hydroxy amide group,and an epoxy group was introduced into its structure.N-OH-9,10-O-ODA was used as a novel collector in the flotation separation of spodumene from one of its associated gangue minerals,specifically albite.N-OH-9,10-O-ODA exhibits remarkable selectivity,with a stronger affinity for collecting spodumene particles compared to albite particles.Zeta potential measurements and X-ray photoelectron spectroscopic analysis reveal that the adsorption quantity of N-OH-9,10-O-ODA on spodumene surface is comparable to that on albite surface.First-principles calculations demonstrate the diverse adsorption configurations of N-OH-9,10-O-ODA on surfaces of spodumene and albite,leading to its distinct collecting abilities for spodumene and albite particles.