Microstructures and Toughness of Weld Metai of Ultrafine Grained Ferritic Steel by Laser Welding

3 mm thick 400 MPa grade ultrafine grained ferritic steel plates were bead-on-plate welded by CO2 laser with heat input of 120-480 J/mm. The microstructures of the weld metal mainly consist of bainite, which form is lower bainite plates or polygonal ferrite containing quantities of dispersed cementite particles, mixed with a few of low carbon martensite laths or ferrite, depending on the heat input. The hardness and the tensile strength of the weld metal are higher than those of the base metal, and monotonously increase as the heat input decreases. No softened zone exists in heat affected zone (HAZ). Compared with the base metal, although the grains of laser weld are much larger, the toughness of the weld metal is higher within a large range of heat input. Furthermore, as the heat input increases, the toughness of the weld metal rises to a maximum value, at which point the percentage of lower bainite is the highest, and then drops.

Microstructure and tensile properties of ultrafine grained copper processed by equal-channel angular pressing

Equal-channel angular pressing （ECAP） process was applied to a 12 mm ×12 mm ×80 mm billet of pure copper （99.98 wt.%） at room temperature. The shear deformation characteristics, microstructure evolution, and tensile properties were investigated. A combination of high strength （-420 MPa） and high elongation to failure （-25%） was achieved after eight ECAP passes at room temperature. The mixing of ultrafme grains （-0.2 μm） with nanocrystalline grains （-80 nm） resulted in high tensile strength and ductility.

Underwater friction stir welding of ultrafine grained 2017 aluminum alloy

2017 aluminum alloy plates with an ultrafine grained （UFG） structure were produced by equal channel angular processing （ECAP） and then were joined by underwater friction stir welding （underwater FSW）. X-ray diffractometer （XRD）, transmission electron microscope （TEM）, scanning electron microscope （SEM） and microhardness tester were adopted to investigate the microstructural and mechanical characteristics of the FSW joint. The results indicate that an ultrafine grained microstructure with the mean grain size of-0.7 Ixm is obtained in the weld nugget by using water cooling. However, The FSW joint exhibits softening compared with the ultrafine grained based material and the heat affected zone （HAZ） has the lowest hardness owing to the coarsening of the strengthening precipitates.

Ultrafine Grain Tungsten Heavy Alloys with Excellent Performance Prepared by Spark Plasma Sintering

Ultrafine grain tungsten heavy alloys (WHAs) were successfully produced from the nano-crystalline powders using spark plasma sintering.The present study mainly discussed the effects of sintering temperature on the density,microstructure and mechanical properties of the alloys.The relative density of 98.12% was obtained at 1 050 ℃,and the tungsten grain size is about 871 nm.At 1 000 ℃-1 200 ℃,the mechanical properties of the alloys tend to first rise and then goes down.After SPS,the alloy exhibits improved hardness (84.3 HRA at 1 050 ℃) and bending strength (987.16 MPa at 1 100 ℃),due to the ultrafine-grained microstructure.The fracture mode after bending tests is mainly characterized as intergranular or intragranular fracture of W grains,interfacial debonding of W grains-binding phase and ductile tearing of binding phase.The EDS analysis reveals a certain proportion of solid solution between W and Ni-Fe binding phase.The good mechanical properties of the alloys can be attributed to grain refinement and solid solution strengthening.

Influence of High-Speed Milling Process on Mechanical and Microstructural Properties of Ultrafine Grained Profiles Produced by Linear Flow Splitting

The effects of milling parameters on the surface quality,microstructures and mechanical properties of machined parts with ultrafine grained(UFG)gradient microstructures are investigated.The effects of the cutting speed,feed per tooth,cutting tool geometry and cooling strategy are demonstrated.It has been found that the surface quality of machined grooves can be improved by increasing the cutting speed.However,cryogenic cooling with CO_2 exhibits no significant improvement of surface quality.Microstructure and hardness investigations revealed similar microstructure and hardness variations near the machined groove walls for both utilized tool geometries.Therefore,cryogenic cooling can decrease more far-ranging hardness reductions due to high process temperatures,especially in the UFG regions of the machined parts,whilst it cannot prevent the drop in hardness directly at the groove walls.

Effect of grain boundary sliding on the toughness of ultrafine grain structure steel: A molecular dynamics simulation study

Molecular dynamics simulations are carried out to investigate the mechanisms of low-temperature impact toughness of the ultrafine grain structure steel. The simulation results suggest that the sliding of the {001 }/{ 110} type and { 110}/{ 111 } type grain boundary can improve the impact toughness. Then, the mechanism of grain boundary sliding is studied and it is found that the motion of dislocations along the grain boundary is the underlying cause of the grain boundary sliding. Finally, the sliding of the grain boundary is analyzed from the standpoint of the energy. We conclude that the measures which can increase the quantity of the {001}/{110} type and {110}/{ 111} type grain boundary and elongate the free gliding distance of dislocations along these grain boundaries will improve the low-temperature impact toughness of the ultrafine grain structure steel.

Microstructures of an Ultrafine Grained SS400 Steel in an Industrial Scale

The microstructures of a SS400 steel after thermomechanical control process（TMCP） in an industrial production were observed by optical microscope,scanning electron microscope（SEM） and transmission electron microscope（TEM）.The results indicated that the size of ferrite grains was 4-5μm,and transmission of ferrite was around 70%.The types of the ultrafine ferrite grains were analyzed and the strengthening mechanisms were discussed.The results show that the ultrafine ferrite grains came from three processes,i.e.deformation induced ferrite transformation（DIFT）.dynamic recrystallization of ferrite and accelerated cooling process.The increase in the strength of the material was mainly due to the grain refining.

High-performance Mg–Zn alloy achieved by the ultrafine grain and nanoparticle design

Improving the comprehensive performance of low alloyed Mg is a significant challenge for biomedical applications.This paper developed a high-performance Mg–Zn alloy with uniform ultrafine grains and nano-precipitates through a straightforward,high-temperature reciprocating equal channel angle extrusion(ECAP)process and researched the microstructure,mechanical property,degradation behaviour,and biocompatibility of the developed alloy.Results showed that the lean Mg–2Zn alloy successfully refined grain to about 1μm and produced plenty of nano-particles with uniform distribution,providing high comprehensive mechanical properties(YS:235 MPa,UTS:267 MPa,EL:15.6%).Additionally,Zn-riched nano-particles in the matrix could decrease the Zn aggregation at the corrosion layer-matrix interface and form a dense oxide film,achieving a low degradation rate(0.13 mm/year in vivo).Finally,this work realizes the low alloy content,low cost,and good properties of one biodegradable Mg alloy,which will benefit the promotion of future clinical applications.

Ultrafine Grained Duplex Structure Developed by ART-annealing in Cold Rolled Medium-Mn Steels

The microstructural evolutions of the cold rolled Fe-0.1C-5Mn steel during intercritical annealing were ex- amined using combined advanced techniques. It was demonstrated that intercritical annealing results in an ultrafine granular ferrite and austenite duplex structure in cold rolled 0.1C-5Mn steel. The strong partitioning of manganese and carbon elements from ferrite to austenite was found during intercritical annealing by scanning transmission elec- tron microscopy （STEM） and X-ray diffraction （XRD）. Strong effects of boundary characters on the austenite for- mation were indicated by austenite fast nucleation and growth in the high angle boundaries but sluggish nucleation and growth in the low angle boundaries. The ultrafine grained duplex structure in 0.1C-5Mn was resulted from the the sluggish Mn-diffusion and the extra high Gibbs free energy of ferrite phase. Based on the analysis of the micro- structure evolution, it was pointed out that the intercritical annealing of the medium Mn steels could be applied to fabricate an ultrafine duplex grained microstructure, which would be a promising approach to develop the 3rd genera- tion austomobile steels with excellent combination of strength and ductility.

New forming method of manufacturing cylindrical parts with nano/ultrafine grained structures by power spinning based on small plastic strains

A new spinning method to manufacture the cylindrical parts with nano/ultrafine grained structures is proposed, which consists of quenching, power spinning and recrystallization annealing. The microstructural evolution during the different process stages and macroforming quality of the spun parts made of ASTM 1020 steel are investigated. The results show that the microstructures of the ferrites and pearlites in the ASTM 1020 steel are transformed to the lath martensites after quenching. The martensite laths obtained by quenching are refined to 87 nm and a small amount of nanoscale deformation twins with an average thickness of 20 nm is generated after performing a 3-pass stagger spinning with 55% thinning ratio of wall thickness, where the equivalent strain required is only 0.92. The equiaxial ferritic grains with an average size of 160 nm and nano-carbides are generated by subsequent recrystallization annealing at 480°C for 30 min. The spun parts with high dimensional precision and low surface roughness are obtained by the forming method developed in this work, combining quenching with 3-pass stagger spinning and recrystallization annealing.

Grain-refining and strengthening mechanisms of bulk ultrafine grained CP-Ti processed by L-ECAP and MDF

The microstructural evolution and mechanical properties of ultrafine-grained(UFG)CP-Ti after an innovative large-volume equal channel angular pressing(L-ECAP)and multi-directional forging(MDF)were systematically examined using monotonic tensile tests combined with transmission electron microscope(TEM)and electron backscatter diffraction(EBSD)techniques.Substantially refined and homogeneous microstructures were achieved after L-ECAP(8-pass and 12-pass)and MDF(2-cycle and 3-cycle),respectively,where the grain size distribution conformed to lognormal distribution.The grain refinement of450℃L-ECAP is dominated by dynamic recrystallization(DRX)and dynamic recovery(DRV),while that of MDF is dominated by DRX.The iron impurities promote recrystallization by pinning-induced dislocation accumulation so that DRX is prone to occur at iron segregation regions during L-ECAP.The monotonic tensile results show that the strain hardening rate of CP-Ti increases with the decrease of grain size,while the continuous strain hardening ability decreases.The relationship between the average grain size and yield strength is in accordance with Hall-Petch relationship.Meanwhile,the individual strengthening mechanisms were quantitatively examined by the modified model.The results indicate that the strengthening contribution of dislocation accumulation to yield strength is greater than that of grain refinement.

Effects of SiC Nanoparticle Content on the Microstructure and Tensile Mechanical Properties of Ultrafine Grained AA6063-SiC_(np) Nanocomposites Fabricated by Powder Metallurgy

Ultrafine grained AA6063-SiCnpnanocomposites with 1, 5 and 10 vol.% SiCnphave been fabricated by a novel powder metallurgy process. This process combines high energy ball milling of a mixture of 6063 alloy granules made from machining chips and Si C nanoparticles and thermomechanical powder consolidation by spark plasma sintering and hot extrusion. The microstructure and tensile mechanical properties of the samples were investigated in detail. Increasing the Si C nanoparticle content from 1 to 10 vol.%,the yield strength and ultimate tensile strength increased from 296 and 343 MPa to 545 and 603 MPa respectively, and the elongation to fracture decreased from 10.0%, to 2.3%. As expected, a higher Si C nanoparticle content generates a stronger inhibiting effect to grain growth during the thermomechanical powder consolidation process. Analysis of the contributions of various strengthening mechanisms shows that a higher Si C nanoparticle content leads to a higher contribution from nanoparticle strengthening, but grain boundary strengthening still makes the largest contribution to the strength of the nanocomposite.When the Si C nanoparticle content increased to 10 vol.%, the failure of the nanocomposite was initiated at weakly-bonded interparticle boundaries(IPBs), indicating that with a high flow stress during tensile deformation, the failure of the material is more sensitive to the presence of weakly-bonded IPBs.

A superior strength-ductility synergy of Al_(0.1)CrFeCoNi high-entropy alloy with fully recrystallized ultrafine grains and annealing twins

Grain refinement usually makes the materials stronger,while ductility has a dramatic loss.Here,a superior tensile strength–ductility synergy in a fully recrystallized ultrafine-grained(UFG)Al_(0.1)CrFeCoNi with abundant annealing twins was achieved by cold rolling at room temperature and short-time annealing.The microstructure characterization using electron backscattered scattering diffraction demonstrates that abundant geometrically necessary dislocations(GNDs)gather around the grain boundaries and twin boundaries after tensile deformation.Although coarse-grained(CG)samples undergo a larger plastic deformation than UFG samples,the GND density decreases with grain size ranging from UFG to CG.Transmission electron microscopy results reveal that the annealing twin boundary,which effectively hinders the dislocation slip and stores dislocation in grain interior,and the activation of multiple deformation twins are responsible for the superior strength–ductility synergy and work hardening ability.In addition,the yield strength of fully recrystallized Al_(0.1)CrFeCoNi follows a Hall–Petch relationship(σ_y=24+676d^(–1/2)),where d takes into account both grain boundaries and annealing twin boundaries.The strengthening effects of grain boundaries and annealing twin boundaries were also evaluated separately.

Thermally stable ultrafine grained copper induced by CrB/CrB_(2) microparticles with surface nanofeatures via regular casting

Ultrafine-grained(UFG)/nanocrystalline materials possess novel properties. Refining as-solidified grains of metals to the ultrafine and even nanometer scale by nanoparticles via slow cooling has been recently discovered. Here, we report that microparticles(CrB and CrB_(2)) with surface nanofeatures can also enable ultrafine/nano grains via slow cooling. CrB/CrB_(2) microparticles, formed by coalescence of nanoparticles in Cu matrix, display surface nanofeatures, which induce substantial grain refinement and stabilization down to the ultrafine/nano scale. The UFG Cu/Cr B and Cu/CrB_(2) samples exhibit exceptional thermal stability, comparable to UFG Cu induced by nanoparticles, without coarsening after annealing at 600°C for 1 h. The microhardness, strengths, and Young's moduli of the Cu/Cr B and Cu/CrB_(2) samples are significantly enhanced over pure Cu. This discovery has great potential to advance the mass production UFG/nanocrystalline for widespread applications.

TEMPERATURE SENSITIVITY AND PREDICTION OF THE MECHANICAL BEHAVIORS OF ULTRAFINE GRAINED ALUMINUM UNDER UNIAXIAL COMPRESSION

In the present work, we explore the strain hardening behaviors as well as the effect of temperature on the plastic deformation of ultrafine grained aluminum. The temperature sensitivity is determined and compared with that of coarse grained material. The results indicate that the flow stress of ultrafine grained aluminum displays enhanced sensitivity to temperature. The reduction in activation volume is suggested to be the major reason for the enhanced temperature sensitivity as grain size is refined into the sub-micrometer regime. Finally, a phenomenological constitutive model is proposed to describe the post-yield response of ultrafine grained aluminum.

Achieving Large-area Bulk Ultrafine Grained Cu via Submerged Multiple-pass Friction Stir Processing

Large-area bulk ultrafine grained （UFG） pure Cu was successfully prepared by multiple-pass overlapping friction stir processing （FSP） under additional rapid cooling. Overlapping FSP did not exert a significant effect on the microstructure and mechanical properties of the FSP UFG Cu. Similar average grain size was achieved in the transitional zone （TZ） of the multiple-pass FSP sample compared to that in the nugget zone of the single-pass FSP sample, and the TZ exhibited a strong {111}（112） type A fiber shear texture, Very weak softening occurred in the TZ of the multiple-pass FSP UFG Cu, resulting in a relatively uniform hardness distribution throughout the whole processed zone. A high yield strength of - 310 MPa and a uniform elongation of - 13% were achieved in the bulk FSP UFG Cu. This study provides an effective strategy to prepare large-area bulk IUFG materials.

Grain size altering yielding mechanisms in ultrafine grained high-Mn austenitic steel:Advanced TEM investigations

The underlying mechanism of discontinuous yielding behavior in an ultrafine-grained(UFG)Fe-31 Mn-3 Al-3 Si(wt.%)austenitic TWIP steel was investigated by the use of advanced TEM technique with taking the plastic deformation mechanisms and their correlation with grains size near the macroscopic yield point into account.Typical yield drop mechanisms such as the dislocation locking by the Cottrell atmosphere due to the presence of interstitial impurities cannot explain the origin of this phenomenon in the UFG high-Mn austenitic TWIP steel.Here,we experimentally revealed that the plastic deformation mechanisms in the early stage of deformation,around the macroscopic yield point,show an obvious association with grain size.More specifically,the main mechanism shifts from the conventional slip in grain interior to twinning nucleated from grain boundaries with decreasing the grain size down to less than 1μm.Our observation indicates that the grain size dependent deformation mechanisms transition is also deeply associated with the discontinuous yielding behavior as it could govern the changes in the grain interior dislocation density of mobile dislocations around the macroscopic yield point.

Fabrication of large-bulk ultrafine grained 6061 aluminum alloy by rolling and low-heat-input friction stir welding

In this study, the ultrafine grained （UFG） 6061 Al alloys fabricated by cold rolling were friction stir welded （FSW） with different rotation rates under both air cooling and rapid cooling in water. Low-heat-input parameters of 400 rpm rotation rate in water （400-Water） could effectively inhibit the coarsening of recrystallized grains, reduce the precipitation rate, and retain more dislocations of the UFG 6061 Al parent metal. 400-Water joint showed high lowest-hardness value, narrow low-hardness zone, and high tensile strength, attributing to the effect of dislocation, grain boundary, solid-solution, and precipitation hardening. This work provides an effective strategy to fabricate large-sized bulk UFG AI alloy by cold rolling with large deformation and low-heat-input FSW.

DAMPING BEHAVIOR OF ULTRAFINE-GRAINED PURE ALUMINUM L2 AND THE DAMPING MECHANISM

Ultrafine-grained pure aluminum L2 with a mean grain size of 1.01μm was produced by equal channel angular pressing （ECAP） and annealing at 150℃ for 2h. Damping behavior of the alloy was measured using a dynamic mechanical thermal analyzer. The alloy had an excellent damping capacity Q^-1 with the ambient value being 9.8×10^-3 at 1.0Hz when the strain amplitude was 2.0×10^-5. The damping behavior of the alloy showed a non-linear damping variation tendency, that is, with an increase in temperature and a decrease of frequency, the damping capacity of the alloy increased. The damping capacity increased with the strain amplitude when the strain amplitude was less than 4.6×10^-5. When the strain amplitude was higher than 4.6×10^-5, the damping capacity became a constant and independent of strain amplitude. The high damping capacity was attributed to dislocation unpinning and a drag of dislocation on pinning points.

Texture evolution and mechanical anisotropy of an ultrafine/nano-grained pure copper tube processed via hydrostatic tube cyclic expansion extrusion

Texture evolution and mechanical anisotropic behavior of an ultrafine-grained(UFG)pure copper tube processed by recently introduced method of hydrostatic tube cyclic expansion extrusion(HTCEE)was investigated.For the UFG tube,different deformation behavior and a significant anisotropy in tensile properties were recorded along the longitudinal and peripheral directions.The HTCEE process increased the yield strength and the ultimate strength in the axial direction by 3.6 and 1.67 times,respectively.Also,this process increased the yield strength and the ultimate strength in the peripheral direction by 1.15 and 1.12 times,respectively.The ratio of ultimate tensile strength in the peripheral direction to that in the axial direction,as a criterion for mechanical anisotropy,are 1.7 and 1.16 for the as-annealed coarse-grained and the HTCEE processed UFG tube,respectively.The results are indicative of a reducing effect of the HTCEE process on the mechanical anisotropy.Besides,after HTCEE process,a low loss of ductility was observed in both directions,which is another advantage of HTCEE process.Hardness measurements revealed a slight increment of hardness values in the peripheral direction,which is in agreement with the trend of tensile tests.Texture analysis was conducted in order to determine the oriental distribution of the grains.The obtained{111}pole figures demonstrate the texture evolution and reaffirm the anisotropy observed in mechanical properties.Scanning electron microscopy micrographs showed that different modes of fracture occurred after tensile testing in the two orthogonal directions.