PREPARATION OF WATERBORNE ULTRAFINE PARTICLES OF EPOXY RESIN BY PHASE INVERSION TECHNIQUE

Waterborne ultrafine particles of epoxy resin were prepared by phase inversion technique. The results of SEM revealed that the particles diameter was in the range of 50 to 100 nm and the effects on amount of water required at phase inversion point were also discussed.

Sources,characteristics,toxicity,and control of ultrafine particles:An overview

Air pollution by particulate matter(PM)is one of the main threats to human health,particularly in large cities where pollution levels are continually exceeded.According to their source of emission,geography,and local meteorology,the pollutant particles vary in size and composition.These particles are conditioned to the aerodynamic diameter and thus classified as coarse(2.5–10μm),fine(0.1–2.5μm),and ultrafine(<0.1μm),where the degree of toxicity becomes greater for smaller particles.These particles can get into the lungs and translocate into vital organs due to their size,causing significant human health consequences.Besides,PM pollutants have been linked to respiratory conditions,genotoxic,mutagenic,and carcinogenic activity in human beings.This paper presents an overview of emission sources,physicochemical characteristics,collection and measurement methodologies,toxicity,and existing control mechanisms for ultrafine particles(UFPs)in the last fifteen years.

Morphology and Structure Analyses of SnO2 Thin Film Coated on Al2O3 Ultrafine Particles by Gas Phase Reaction in Fluidized Bed

Fluidized chemical vapor deposition (FCVD) technology was developed for coating SnO 2 thin film on ultrafine Al 2O 3 particles.Transmission electron microscopy (TEM) and high resolution electron microscopy (HREM) analyses demonstrated that SnO 2 films with different structures were deposited through controlling the coating temperature, reactant concentration, etc .. Nanocrystalline SnO 2 film was formed at 572.15K by gas phase reaction of SnCl 4 and H 2O.Electron probe microanalyser (EPMA) and energy dispersive spectrometer (EDS) analyses indicated that the distribution of nanocrystalline SnO 2 over inner and outer part of the Al 2O 3 agglomerates was homogeneous.

Mssbauer Effect in Ultrafine Particles with Fe-C Solid Solution,γ-Fe and Fe_3C Phases

Ultrafine particles prepared by evaporating pure Fe in CH4 atmosphere using arc-dischargeheating method, were found to consist of Fe-C solid solution, γ-Fe and Fe3C phases. EfFect of annealing temperature on phase transformation and hyperfine interactions has been investigated by Mossbauer spectroscopy, X-ray diffraction (XRD), differential thermal analysis and thermogravimetry (DTA-TG), transmission electron microscopy (TEM), oxygen determination and vibrating sample magnetometer (VSM) measurements. It was observed that phase transformation of γ-Fe to α-Fe occurs during annealing in vacuum. The mechanism causing the change of hyperfine interactions with annealing temperature differs for Fe-C solution and interstitial compounds. DifFerence of hyperfine interactions of Fe-C solid solution in the starting sample and its annealed samples is ascribed to the improvement of activation of interstitial carbon atoms. Stress-relieving in structure of annealed Fe3C particle can result in a weak influence on hyperfine interactions. Parameters fitted to the Mossbauer spectra show the existence of superparamagnetism in all the samples. Absorbed and combined oxygen on particle surface of the starting sample were determined.

Photoluminescence Studies on Ferric Oxide Ultrafine Particles

ＰｈｏｔｏｌｕｍｉｎｅｓｃｅｎｃｅＳｔｕｄｉｅｓｏｎＦｅｒｒｉｃＯｘｉｄｅＵｌｔｒａｆｉｎｅＰａｒｔｉｃｌｅｓＺＨＡＮＧＹａｎ；ＡＩＸｉ－ｃｈｅｎｇ；ＸＩＡＯＬｉａｎｇ－ｚｈｉｐ；ＦＥＩＨａｏ－ｓｈｅｎｇ；ａｎｄＬＩＴｉｅ－ｊｉｎ（Ｄｅｐａｒｔｍｅｎ...

X-ray Diffraction Line Profile Broadening of Fe_(50)Pd_(50) Alloy Ultrafine Particles

The composition distribution in Fe50Pd50 alloy ultrafine particles prepared by inert gas condensation method was investigated in details by means of X-ray diffraction technique through deconvolution of the X-ray diffraction data. The microscopic composition distribution in the alloy UFP was identified, which is caused by nonuniformity of the melt, fractional distillation during the evaporation process and statistical fluctuation during nucleation and coalescence of the alloy particles. The composition distribution affects the properties of the alloy UFP

Size-dependent Initial Sintering Temperature of Ultrafine Particles

A model for the size-dependent initial sintering temperature of ultrafine particles was established. The theoretical predictions for the size-dependent sintering temperatures of W, Ni and Ag ultrafine particles are consistent with available experimental

Study of Potential Health Damage Caused by Ultrafine Particles in Megacities Using a Pulmonary Deposition Model

The deposition of ultrafine particles, in the human respiratory tract, from four highly impacted megacities across the globe, was evaluated by using a pulmonary deposition model. It was found that, for the locations studied, an average of 62% of atmospheric particles was retained in the respiratory system. As expected, the model shows that smaller particles penetrate deeper in the airways. In addition, it’s shown that children are more susceptible than adults, retaining 8% more ultrafine particles.

Preparation and Characterization of CeO_2-ZrO_2 Solid Solution Ultrafine Particles Using Reversed Microemulsion

Ce0.6Zr0.4O2 solid solution ultrafine particle was prepared in the cyclohexane/water/OP-10/n-hexanol reversed microemulsion. The quasi-ternary phase diagram investigations showed that the system has narrow W/O type microemulison region, so it is the proper system to prepare Ce0.6Zr0.4O2 solid solution ultrafine particle. Some physical-chemical techniques such as TG/DTA, XRD, BET, and HRTEM are used to characterize the resultant powders. The results show that the fluorite cubic Ce0.6Zr0.4O2 solid solution is obtained at 400 ℃. The surface area is （146.7 m^2·g^-1）, which is higher than the surface area for sol-gel prepared sample （59.5m^2·g^-1）. HRTEM images indicated that the Ce0.6Zr0.4O2 solid solution ultrafine particle is well-crystallized, narrow size distribution, less agglomeration, within mean size of 5 -7 nm.

Studies on the Lanthanum-Modified Lead Titanate Ultrafine Particles by Raman Spectroscopy

ＳｔｕｄｉｅｓｏｎｔｈｅＬａｎｔｈａｎｕｍ┐ＭｏｄｉｆｉｅｄＬｅａｄＴｉｔａｎａｔｅＵｌｔｒａｆｉｎｅＰａｒｔｉｃｌｅｓｂｙＲａｍａｎＳｐｅｃｔｒｏｓｃｏｐｙＣＵＩＡｉ－ｌｉ＊，ＧＥＸｕ－ｄｏｎｇ，ＨＵＹｏｎｇ－ｑｉａｎｄＪＩＮＹｏｎｇ（Ｄｅｐａｒｔ...

The Magnetic Properties and Effective Magnetic Anisotropy of Fe-Ni Ultrafine Particles

Fe 100- x Ni x alloys of ultrafine particle with the average grain size of about 10 nm were synthesized by mechanically alloying process. The samples were investigated by X ray diffraction and measurements of the saturation magnetization and coercivity force. Both b.c.c and f.c.c phase exist within a wide range for Fe 100- x Ni x , while x ≤45. The effective magnetic anisotropy K e was measured by applying the law of approach to saturation. The value of K e decreases with an increase of Ni content. It is noticed that the strain anisotropy makes a large contribution to the magnetic anisotropy. The estimation of grain size leads to the determination of the single domain critical size and domain wall energy. The exchange stiffness and exchange integral deduced from the relationship between the effective magnetic anisotropy and domain wall energy are in agreement with that calculated by other methods.

Adverse effects of exposure to fine particles and ultrafine particles in the environment on different organs of organisms

Particulate pollution is a global risk factor that seriously threatens human health.Fine particles(FPs)and ultrafine particles(UFPs)have small particle diameters and large specific surface areas,which can easily adsorb metals,microorganisms and other pollutants.FPs and UFPs can enter the human body in multiple ways and can be easily and quickly absorbed by the cells,tissues and organs.In the body,the particles can induce oxidative stress,inflammatory response and apoptosis,furthermore causing great adverse effects.Epidemiological studies mainly take the population as the research object to study the distribution of diseases and health conditions in a specific population and to focus on the identification of influencing factors.However,the mechanism by which a substance harms the health of organisms is mainly demonstrated through toxicological studies.Combining epidemiological studies with toxicological studies will provide a more systematic and comprehensive understanding of the impact of PM on the health of organisms.In this review,the sources,compositions,and morphologies of FPs and UFPs are briefly introduced in the first part.The effects and action mechanisms of exposure to FPs and UFPs on the heart,lungs,brain,liver,spleen,kidneys,pancreas,gastrointestinal tract,joints and reproductive system are systematically summarized.In addition,challenges are further pointed out at the end of the paper.This work provides useful theoretical guidance and a strong experimental foundation for investigating and preventing the adverse effects of FPs and UFPs on human health.

Application of efficient and sustainable freeze-dissolving technology in manufacturing of KHCO_(3)ultrafine particles

The development of ultrafine particles provided a new way to solve problems in the fields of energy,environment,and medicine,and had become one of the most promising technologies.Therefore,the application of ultrafine particles required the development of cleaner,greener,and more efficient preparation methods.The new freeze-dissolving technology has been applied in manufacturing of KHCO_(3)ultrafine particles,with an aqueous solution of 0.02-0.1 g KHCO_(3)/g water.Frozen ice particles were formed after dripping the solution into liquid nitrogen.The antisolvent ethanol was used to dissolve the ice spherical template at a temperature below 273.15 K,and the pre-formed KHCO_(3)ultrafine particles inside the ice template remained in the ethanol aqueous solution.The ice particles were put into the freeze dryer to isolate the ultrafine KHCO_(3)particles.Compared with the particles produced with traditional freeze-drying technology,the ultrafine powder/particles produced by the freeze-dissolving technology were smaller with narrower size distribution.The freeze-dissolving technology has demonstrated a much more sustainable and efficient manufacturing process than the traditional freeze-drying process.In addition,the influence of the concentrations of KHCO_(3)and the sizes of ice particles were investigated with the discussions of mechanisms.

The bio-distribution,clearance pathways,and toxicity mechanisms of ambient ultrafine particles

Ambient particles severely threaten human health worldwide.Compared to larger particles,ultrafine particles(UFPs)are highly concentrated in ambient environments,have a larger specific surface area,and are retained for a longer time in the lung.Recent studies have found that they can be transported into various extra-pulmonary organs by crossing the air-blood barrier(ABB).Therefore,to understand the adverse effects of UFPs,it is crucial to thoroughly investigate their bio-distribution and clearance pathways in vivo after inhalation,as well as their toxicological mechanisms.This review highlights emerging evidence on the bio-distribution of UFPs in pulmonary and extra-pulmonary organs.It explores how UFPs penetrate the ABB,the blood-brain barrier(BBB),and the placental barrier(PB)and subsequently undergo clearance by the liver,kidney,or intestine.In addition,the potential underlying toxicological mechanisms of UFPs are summarized,providing fundamental insights into how UFPs induce adverse health effects.

Improving flow and fluidization quality of fine and ultrafine particles via nanoparticle modulation

Fine and ultrafine particles possess great potential for industrial applications ascribed from their huge specific surface area and ability to provide good gas–solid contact.However,these powders are inherently cohesive,making it challenging to achieve smooth flow and fluidization.This challenge can be well-resolved by nanoparticle modulation(nano-modulation),where a small amount of nanoparticles is uniformly mixed with the cohesive fine/ultrafine powders.Through nano-modulation,the fluidization system of cohesive powders exhibits distinguishable minimum fluidization velocity,enlarged bed expansion ratio(particularly the dense phase expansion),and scarcer,smaller,and slower moving bubbles,indicating improved flow and fluidization quality.The purpose of the current work is to systematically summarize the state-of-the-art progress in the fluidization and utilization of fine and ultrafine particles via the nanoparticle modulation method.Accordingly,a broader audience can be enlightened regarding this promising fine/ultrafine particle fluidization technology,so as to provoke their attention and encourage interdisciplinary integration and industry-academia collaborative research.

Characterization of ultrafine particles from hardfacing coated brake rotors

Automotive brake rotors are commonly made from gray cast iron(GCI).During usage,brake rotors are gradually worn off and periodically replaced.Currently,replaced brake rotors are mostly remelted to produce brand-new cast iron products,resulting in a relatively high energy consumption and carbon footprint into the environment.In addition,automotive brakes emit airborne particles.Some of the emitted particles are categorized as ultrafine,which are sized below 100 nm,leading to a series of health and environmental impacts.In this study,two surface treatment techniques are applied,ie.,high-velocity oxygen fuel(HVOF)and laser cladding(LC),to overlay wear-resistant coatings on conventional GCI brake rotors in order to refurbish the replaced GCI brake rotor and to avoid the remelting procedure.The two coating materials are evaluated in terms of their coefficient of friction(CoF),wear,and ultrafine particle emissions,by comparing them with a typical GCI brake rotor.The results show that the CoF of the HVOF disc is higher than those of the GCI and LC discs.Meanwhile,HVOF disc has the lowest wear rate but results in the highest wear rate on the mating brake pad material.The LC disc yields a similar wear rate as the GCI disc.The ultrafine particles from the GCI and LC discs appeared primarily in round,chunky,and flake shapes.The HVOF disc emits unique needle-shaped particles.In the ultrafine particle range,the GCI and HVOF discs generate particles that are primarily below 100 nm in the running-in period and 200 nm in the steady state.Meanwhile,the LC disc emitted particles that are primarily~200 nm in the entire test run.

Nest-like multilevel structured graphene oxide-on-polyacrylonitrile membranes for highly efficient filtration of ultrafine particles

Developing filtration media for particulate matter(PM)removal has been proven to be extremely challenging.Here,we report a facile and scalable strategy to fabricate a multi-level structured polyacrylonitrile/graphene oxide(PAN/GO)air filtration membrane to remove ultrafine particles in air by combining multi-jet electrospinning and physical bonding.Our approach allows the thin PAN nanofibers and two-dimensional GO nanosheets to form interpenetrating bonding structures on non-woven fabric and to assemble into stable filtration media.The resultant composite membranes can filtrate 300 nm particles with a high removal efficiency of 98.8%,a low pressure drop of 55 Pa,and a desirable quality factor of 0.34 Pa^(-1).This multi-level PAN/GO filter is expected to have wider applications not only for the ultrafine particle filtration and separation but also for the design of three-dimensional functional structures in the future.

Preparation of Ultrafine γ-Al_2O_3 Particles in Non-ionic Water in Oil Microemulsions

Ultrafine γ-A12O3 particles are synthesized in Triton X- 10 0/n - hexanol/cycloh exan e/wat er water in o if(w/o )Inicroemulsion by mixing two separately prepared microemulsions containing Al(NO)3 and (Wb)ZCO, respectively.The ultrafine Al2O3 particles are characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD)and their size and distribution are measured. The effects of water, surfactallt and reactant concentrations on the particlesize and distribution are studied. The results show that the particle size and distribution can be changed by varying thepreparation conditions, and the size of the microemulsion droplets has a controlling effect on the size of the pafticles. A. possible mechanism of ultrafine particles (UFPs) prepared by microemulsions is proposed.

Development of a standardized in vitro approach to evaluate microphysical,chemical,and toxicological properties of combustion-derived fine and ultrafine particles

Ultrafine particles represent a growing concern in the public health community but their precise role in many illnesses is still unknown. This lack of knowledge is related to the experimental difficulty in linking their biological effects to their multiple properties, which are important determinants of toxicity. Our aim is to propose an interdisciplinary approach to study fine(FP) and ultrafine(UFP) particles, generated in a controlled manner using a mini CAST(Combustion Aerosol Standard) soot generator used with two different operating conditions(CAST1 and CAST3). The chemical characterization was performed by an untargeted analysis using ultra-high resolution mass spectrometry. In conjunction with this approach, subsequent analysis by gas chromatography–mass spectrometry(GC–MS) was performed to identify polycyclic aromatic hydrocarbons(PAH). CAST1 enabled the generation of FP with a predominance of small PAH molecules, and CAST3 enabled the generation of UFP, which presented higher numbers of carbon atoms corresponding to larger PAH molecules. Healthy normal human bronchial epithelial(NHBE) cells differentiated at the air-liquid interface(ALI) were directly exposed to these freshly emitted FP and UFP. Expression of MUC5AC, FOXJ1, OCLN and ZOI as well as microscopic observation confirmed the ciliated pseudostratified epithelial phenotype. Study of the mass deposition efficiency revealed a difference between the two operating conditions, probably due to the morphological differences between the two categories of particles. We demonstrated that only NHBE cells exposed to CAST3 particles induced upregulation in the gene expression of IL-8 and NQO1. This approach offers new perspectives to study FP and UFP with stable and controlled properties.

Preparation of γ-Al_2O_3 Ultrafine Particlesand Its Application in Hydrogen Peroxide Biosensor

In this article, we illustrated the preparation method of γ Al 2O 3 ultrafine particles. The particle size and morphology were decided by a transmission electron microscopy (TEM) and crystal patterns were determined by an X ray diffractometer (XRD). γ Al 2O 3 ultrafine particles have ultra characters in physics and chemistry, and the hydrogen peroxide biosensors based on it display not only fast response and high sensitivity, but also good stability.