Capillary Zone Electrophoresis of Native Amino Acids with Indirect Ultraviolet Detection

Aim To strdy the separation of native amino acids using capillary zone electro- pboresis (CZE) with indirect ultraviolet detecition. Methods 13 native amino acids were sepa- rated by capillary electrophoresis with indirect detection . The experiments were carried out with homemade CE apparatus under the following operating conditior conditions: a fused-silica capillary col- umn of 50.0cm effect length and of 75m i.d. was used. 7 organic acids were used as BGAE, and a positive potential of separation in CZE with indirect detection. After optimizing for l3 native amino acids were established. Conclusion The choice of BGAe is an important factor influencing the efficiency of separation in CZE with indiect detection .After optimizing the separation conditions a baseline separation for 13 native amino acids is obtained.

Capillary Electrophoretic Determination of Jinggangmycin A in Formulations Using Direct UV Detection

A simple, fast and reliable method was developed for the analysis of jinggangmycin A （validamycin A） in commercial formulations. The running buffer used was acetate buffer （100 mmol/L, pH 4.7） with 15 kV as the applied voltage. The detection was achieved by using direct UV mode at 200 nm and the detection limit was 0.2 μg/mL. Linearity in the concentration range of 5-500 μg/mL was excellent （RE 〉 0.999）. The run-to-run repeatability （n = 3）, as expressed by the relative standard deviation （RSD） for migration times and peak areas were less than 0.5% and 3.0% respectively. The mean recovery ranged from 97.2% to 101.4%.

Key Conditions in Capillary Electrophoresis of Amino Acids with Indirect Ultraviolet Detection

Key factors for capillary electrophoresis of amino acids with indirect ultraviolet detection were illustrated. Buffer compositions and additives were found to be influential as expected, while buffer pH was shown to be particularly critical to the separation and detection. The effect of pH also depended on the electrophoretic mode used. Ways to obtain recurring and selective were suggested.

Determination of toluene diisocyanate in synthetic-rubber track by ion chromatography with ultraviolet detection after alkaline suppressor

In the present work, a novel analytical method was proposed for the determination of toluene diisocyanate （TDI） in syntheticrubber track by ion chromatography （IC） coupled with an ultraviolet detector setting at 212 nm. TDI can be hydrolyzed to toluene diamine （TDA） which can be separated by cation-exchange IC easily. The optimum IC separation was performed on an IonPac CS12A column （150 mm ×4.0 mm） using 20 mmol L^-1 sodium sulfate, 10 mmol L^-1 sulfuric acid and 10% acetonitrile as eluent. It was found that a higher signal response of TDA could be obtained under alkaline condition. A suppressor was used to change the acidic eluent into alkaline one. 0.8 mol L^-1 potassium hydroxide was chosen as the optimum regeneration eluent. With the added suppressor and regenerant, signal response was magnified by about 16 times and lower limit of detection （LOD, 0.13 μg L^-1） was obtained. Within-day relative standard deviation （R.S.D.） was less than 3.6%. The recoveries of TDI spiked in synthetic-rubber track samoles were 96.4-110.6%.

The Ultraviolet Detection of Corona Discharge in Power Transmission Lines

Corona discharge is a common phenomenon in power transmission lines external insulation, and it may cause serious defect if without effective detection. The ultraviolet (UV) imagery technology has been widely used to detect the corona discharge in industry in recent years, but some influence factors’ functions are not definite. In this paper, the fracture aluminum strands which is common in power transmission lines were used as the electrode model while a SuperB ultraviolet imager were utilized to detect, the photon count rate was detected with different detect distance, electric field, aluminum strands length and UV gain were applied. Then the multivariate regression analysis (MRA) was taken to calculate the function between the photon count and the factors.

Detection and Separation of Inorganic Cations in Natural, Potable, and Wastewater Samples Using Capillary Zone Electrophoresis with Indirect UV Detection

Capillary zone electrophoresis (CZE) is a sensitive and rapid technique for determining traces of inorganic cations in water samples. CZE with indirect UV-diode array detection (CZE-DAD) was utilized to identify several inorganic cations in natural, potable, and wastewater samples. A pH 4.35 background electrolyte system was employed and consisted of 15 mM imidazole, 8 mM malonic acid, 2 mM 18-crown-6 ether as complexing agents, 10% v/v methanol as an organic modifier with indirect absorbance reference at 214 nm. The CZE method involved electromigration injection at 5 kV for 5 s, a separation voltage of 20 kV at 25℃, and a detection wavelength of 280 nm. Six main cations (ammonium , potassium K+, calcium Ca2+, sodium Na+, magnesium Mg2+, and lead Pb2+) were tested, and all but lead, were detected in the water samples at concentrations between 0.03 and 755 ppm with a detection limit ranging between 0.023 and 0.084 ppm. The successful evaluation of the proposed methodology allowed us to reliably detect and separate six metal ions in different water samples without any pretreatment. All water samples were collected from Northern New York towns and the Raquette River water system, the third longest river in New York State and the largest watershed of the central and western Adirondacks.

DNA Separation by Capillary Electrophoresis with Ultraviolet Detection using Mixed Synthetic Polymers

The mixtures of two polymers, poly (N,N-dimethylacrylamide) (PDMA) and polyvinylpyrrolidone (PVP) were synthesized and used as the separation medium for double-stranded and single-stranded DNA fragments by capillary electrophoresis with UV detector. On optimal conditions, 2%w/v PDMA + 2%w/v PVP can be used to separate the doublet 123/124bp in pBR322/Hae III Markers.

NON-AQUEOUS REVERSED PHASE HPLC WITH LOW-WAVELENGTH UV DETECTION FOR TRIGLYCERIDE ANALYSIS

Glycerides are first separated to classes of triglycerides(TGs), diglycerides(DGs) and monoglycerides(MGs) by normal phase HPLC on silica gel column. Individual triglyceride separation is then achieved by non-aqueous reversed phase(NARP) HPLC on C_(18) column with UV detection at 215nm.

Test Study on Corona Onset Voltage of UHV Transmission Lines Based on UV Detection

Corona discharge is being detected by UV imaging detection technology at home and abroad in recent years.This technology is used in the corona tests of conductor bundles in this paper.In order to further research the corona characteristic,optimize geometry parameters and diameter of sub-conductor,and increase corona onset voltage of transmission lines,corona tests of three model conductors which are placed inside the outdoor corona cage are conducted.Corona cage could be used to simulate the corona activities on transmission lines under a low voltage and different conditions in an effective and economical way.Photon which was created by UV light as a result of corona discharge on conductors is detected by the UV detection apparatus.The photon number within unit interval,namely photon counting rate is adopted as the parameter of quantifying the intensity of corona discharge.According to the apparent change of photon number,corona onset voltage can be judged.All tests are conducted under almost same atmosphere condition.Using the method,corona onset voltage is acquired.The results indicate that the tests have a good repeatability,in other words,repeating same test twice same result can be aquired.The corona onset voltage can be acquired exactly from the curve of applied voltage vs.photon counting rate.Therefore UV detection apparatus can not only used to find discharge point exactly,but also applied on corona discharge research and live detection for power equipments.The method using in this paper is proved that is a new available method.

Trace Determination of Tamoxifen in Biological Fluids Using Hollow Fiber Liquid-Phase Microextraction Followed by High-Performance Liquid Chromatography-Ultraviolet Detection

The applicability of hollow fiber liquid-phase microextraction (HF-LPME) combined with high-performance liquid chromatography-ultraviolet detection (HPLC-UV) was evaluated for the extraction and determination of tamoxifen (TAM) in biological fluids including human urine and plasma. The drug was extracted from a 15 mL aqueous sample (source phase;SP) into an organic phase impregnated in the pores of the hollow fiber (membrane phase;MP) followed by the back-extraction into a second aqueous solution (receiving phase;RP) located in the lumen of the hollow fiber. The effects of several factors such as the nature of organic solvent, compositions of SP and RP solutions, extraction time, ionic strength and stirring rate on the extraction efficiency were examined and optimized. An enrichment factor of 360 along with substantial sample clean up was obtained under the optimized conditions. The calibration curve showed linearity in the range of 1 - 500 ng?mL–1 and the limit of detection was found to be 0.5 ng?mL–1 in aqueous medium. A reasonable relative recovery (≥89%) and satisfactory intra-assay (3.7% - 4.2%, n = 3) and inter-assay (7.5% - 7.8%, n = 3) precision illustrated good performance of the analytical procedure in spiked human urine and plasma samples.

UV接枝聚硅氧烷-TiO_(2)复合棉织物的制备及性能

通过紫外辐射3-(异丁烯酰氧)丙基三甲氧基硅烷对棉织物进行接枝聚合改性,然后与钛酸四丁酯共水解,形成Si—O—Ti化学键,通过化学键合的形式引入TiO_(2)层。由于Si元素位于棉织物和二氧化钛之间,阻断TiO_(2)光催化降解棉织物。化学键合TiO_(2)与棉织物的结合强度高,提高了耐久性。TiO_(2)对棉织物的整体结构未造成改变,但棉织物的抗紫外线能力显著提升,禁带宽度变小,光催化自清洁能力增强。

UV-LED表面消毒辐射场的数学模拟体系的建立及试验验证

为了实现紫外发光二极管(Ultraviolet Light-Emitting Diodes,UV-LED)表面消毒器设计的优化、高效、智能化目的,研究建立了UV-LED表面消毒辐射场的数学模型,并进行了试验验证。根据该数学模型,编写了VBA(Visual Basic for Applications)程序,对辐射场进行了模拟和分析。结果显示,辐射模型的计算值与实测值接近,试验验证了辐射模型的可行性。试验进行了应用举例,当照射距离与灯间距的比值为0.4时,选择最大发光角90°的UV-LED可使辐射场最优化;当照射距离与灯间距的比值为0.8和1.6时,对应的最优选择分别是45°和30°的UV-LED。数学模型和相关计算方法为优化设计紫外线表面消毒设施提供了模拟、优化的有效工具。

Review of deep ultraviolet photodetector based on gallium oxide

Ultraviolet(UV) photodetectors(PDs) have drawn great attention in recent years due to their potential application in civil and military fields. Because of its ultrawide bandgap, low cost, strong radiation hardness, and high thermal and chemical stability with high visible-light transparency, Ga_2O_3 is regarded as the most promising candidate for UV detection.Furthermore, the bandgap of Ga_2O_3 is as high as 4.7–4.9 eV, directly corresponding to the solar-blind UV detection band with wavelength less than 280 nm. There is no need of doping in Ga_2O_3 to tune its bandgap, compared to AlGaN, MgZnO,etc, thereby avoiding alloy composition fluctuations and phase separation. At present, solar-blind Ga_2O_3 photodetectors based on single crystal or amorphous Ga_2O_3 are mainly focused on metal–semiconductor–metal and Schottky photodiodes.In this work, the recent achievements of Ga_2O_3 photodetectors are systematically reviewed. The characteristics and performances of different photodetector structures based on single crystal Ga_2O_3 and amorphous Ga_2O_3 thin film are analyzed and compared. Finally, the prospects of Ga_2O_3 UV photodetectors are forecast.

Strain H_2-419-4 of Haematococcus pluvialis induced by ethyl methanesulphonate and ultraviolet radiation

Two strains H2-410 and H2-419 were obtained from the chemically mutated survivors of wild Haematococcus pluvialis 2 by using ethyl methanesulphonate (EMS). Strains H2-410 and H2-419 showed a fast cell growth with 13% and 20% increase in biomass compared to wild type, respectively. Then H2-419-4, a fast cell growth and high astaxanthin accumulation strain, was obtained by exposing the strain H2-419 to ultraviolet radiation (UV) further. The total biomass, the astaxanthin content per cell, astaxanthin production of H2-419-4 showed 68%, 28%, and 120% increase compared to wild H. pluvialis 2, respectively. HPLC (High Performance Liquid Chromatography) data showed also an obvious proportional variation of different carotenoid compositions in the extracts of H2-419-4 and the wild type, although no peak of carotenoids appeared or disappeared. Therefore, the main compositions in strain H2-419-4, like its wild one, were free of astaxanthin, monoester, and diester of astaxanthin. The asexual reproduction in survivors after exposed to UV was not synchronous, and different from the normal synchronous asexual reproduction as the mother cells were motile instead of non-motile. Interestingly, some survivors from UV irradiation produced many mini-spores (or gamete?), the spores moved away from the mother cell gradually 4 or 5 days later. This is quite similar to sexual reproduction described by Elliot in 1934. However, whether this was sexual reproduction remains questionable, as no mating process has been observed.

A 4×4 metal-semiconductor-metal rectangular deep-ultraviolet detector array of Ga_(2)O_(3)photoconductor with high photo response

A 4×4 beta-phase gallium oxide(β-Ga_(2)O_(3))deep-ultraviolet(DUV)rectangular 10-fingers interdigital metalsemiconductor-metal(MSM)photodetector array of high photo responsivity is introduced.The Ga2O_(3)thin film is prepared through the metalorganic chemical vapor deposition technique,then used to construct the photodetector array via photolithography,lift-off,and ion beam sputtering methods.The one photodetector cell shows dark current of 1.94 p A,phototo-dark current ratio of 6×10_(7),photo responsivity of 634.15 A·W^(-1),specific detectivity of 5.93×1011cm·Hz1/2·W^(-1)(Jones),external quantum efficiency of 310000%,and linear dynamic region of 108.94 d B,indicating high performances for DUV photo detection.Furthermore,the 16-cell photodetector array displays uniform performances with decent deviation of 19.6%for photo responsivity.

红光补充UV-A对叶用莴苣倍半萜内酯类化合物的调控效应

叶用莴苣特有的苦味来源于倍半萜内酯类化合物,主要包括山莴苣苦素和莴苣苦素等。为探究紫外光对叶用莴苣生长和倍半萜内酯类化合物的调控作用,以纯红光(180μmol·m^(-2)·s^(-1))为对照,比较了补充UV-A(30μmol·m^(-2)·s^(-1))、UV-B(10μmol·m^(-2)·s^(-1))对7个叶用莴苣品种生长及倍半萜内酯类化合物的影响;并进一步分析了红外光添加UV-A补光强度(15、30、45μmol·m^(-2)·s^(-1))及补光时长(0、1、2、3、6、9 d)对叶用莴苣倍半萜内酯类化合物含量的影响。结果表明:添加UV-A处理可显著提高绿罗的地上部鲜质量,显著降低7个叶用莴苣品种的山莴苣苦素和莴苣苦素含量,分别降低了33%~74%和29%~60%。随着UV-A补光强度的增加,叶用莴苣中倍半萜内酯类化合物含量逐渐降低,且以添加30μmol·m^(-2)·s^(-1)UV-A处理2 d后叶用莴苣中山莴苣苦素含量迅速上升,处理3 d时达到峰值,随后逐渐降低;而莴苣苦素含量在处理2 d后基本保持逐步上升的趋势,处理6~9 d时略有下降。综上所述,红光补充适量的UV-A(30μmol·m^(-2)·s^(-1)、3~6 d),可在不影响生物量的基础上显著降低叶用莴苣中倍半萜内酯类化合物含量,从而减轻苦味。

A novel integrated ultraviolet photodetector based on standard CMOS process

A novel integrated ultraviolet（UV） photodetector has been proposed, which realizes a high UV selectivity by combining a conventional UV-selective photodiode with an extra infrared（IR） photodiode. The IR photodiode is designed for compensating the photocurrent response of the UV photodiode in the infrared band and is 15 times smaller than the UV one. The integrated photodetector has been fabricated in a 0.35 μm standard CMOS technology. Some critical performance indices of this new structure photodetector, such as spectral responsivity, breakdown voltage, quenching waveform, and transient response, are measured and analyzed. Test results show that the complementary UV–IR photodetector has a maximum spectral responsivity of 0.27 A·W-1 at the wavelength of 400 nm. The device has a high UV selectivity of 3000,which is much higher than that of the single UV photodiode.

Ultraviolet ZnO Photodetectors with High Gain

Fabrication and characterization of metal-semiconductor-metal ultraviolet （MSM UV） photodetector based on ZnO ultra thin （nano scale） films with Pd Schottky contact are reported. The ZnO thin film was grown on glass substrate by thermal oxidation of preeposited zinc films using vacuum deposition technique. With applied voltage in the range from -3V to 3V, the contrast ratio, responsivity, and detectivity for an incident radiation of 0.1 mW at 365 nm wavelength were estimated. The proposed device exhibited a high gain which was attributed to the hole trapping at semiconductor-metal interface. I-V characteristics were studied and the parameters, such as ideality factor, leakage current, resistance-areaproduct, and barrier height, were extracted from the measured data.

Development of a Detection Method for Assaying Calf Intestine Alkaline Phosphatase Activity

[ Objective] This study was to develop a detection method for assaying calf intestine alkaline phasphatase activity in scientific research. [ Method ] By simulating the conditions and buffers for assaying calf intestine alkaline phosphatase used in the scientific research, the parameters influencing substmte concentration, reaction duration, eoloration time and buffer pH were optimized. [ Result] The activity of alkaline phosphatase detected varied hugely among different buffers, and potassium ferricyanide solution added with boracic acid achieved the stable coloration. The optimal water bath time was determined as 10 rain, and the substrate concentration was optimized as 0.04 moL/L. The increasing temperature did not have a large influence on low temperature enzymatic activity while did on high coneentration enzymatic activity. When the buffer pH was 7.0 - 8.0, the detection stability of alkaline phosphatase could be maintained well The ion intensity of buff- er had little effects on alkaline phasphatase activity. [ Conclusion] A detection method for assaying calf intestine alkaline phosphatase activity in scientific research was successfully developed in this study.

Organometallic perovskite single crystals grown on lattice-matched substrate for photodetection

In this work,we demonstrate that an organometallic perovskite(OP)single crystal for effective photodetection can be grown on a gold(Au)-decorated substrate using liquid phase epitaxy.The covered gold could both control the shape of the epitaxial layer and act as its electrodes.An MAPbCl3 single crystal and an MAPbBr1.5Cl1.5 single crystal were used as the substrate and the epitaxial layer,respectively.The device,with an Au-perovskite-Au structure,can be fully characterized.Due to the high-quality epitaxial layer,the maximum external quantum efficiency(EQE)value is over 60%under the voltage of
20 V.In addition,the response speed can reach 200 and 500 ns(ns)rise and fall,respectively.Our work provides an effective and promising method to fabricate efficient perovskite-based photodetectors.