Influences of the Fresh Air Volume on the Removal of Cough-Released Droplets in a Passenger Car of a High-Speed Train Using CFD

The spread and removal of pollution sources,namely,cough-released droplets in three different areas(front,middle,and rear areas)of a fully-loaded passenger car in a high-speed train under different fresh air flow volume were studied using computational fluid dynamics(CFD)method.In addition,the structure of indoor flow fields was also analysed.The results show that the large eddies are more stable and flow faster in the air supply under Mode 2(fresh air volume:2200m3/h)compared to Mode 1(fresh air volume:1100m3/h).By analysing the spreading process of droplets sprayed at different locations in the passenger car and with different particle sizes,the removal trends for droplets are found to be similar under the two air supply modes.However,when increasing the fresh air flow volume,the droplets in the middle and front areas of the passenger car are removed faster.When the droplets had dispersed for 60s,Mode 2 exhibited a removal rate approximately 1%–3%higher than Mode 1 for small and medium-sized droplets with diameters of 10 and 50μm.While those in the rear area,the situation is reversed,with Mode 1 slightly surpassing Mode 2 by 1%–3%.For large droplets with a diameter of 100μm,both modes achieved a removal rate of over 96%in all three regions at the 60 s.The results can provide guidance for air supply modes of passenger cars of high-speed trains,thus suppressing the spread of virus-carrying droplets and reducing the risk of viral infection among passengers.

Experimental study on thermal environment in large-space building with low sidewall air supply

The thermal environmental characteristics are experim-entally studied in terms of different air supply volumes and outdoor meteorological parameters in a large-space building which is air conditioned with a low sidewall air supply.The experimental results show that the indoor vertical temperature distributions under different condition are similar.The maximum vertical temperature difference（MVTD）is up to about 20 ℃,and it linearly changes with the sol-air temperature.The indoor vertical temperature gradients（VTGs）in the upper,central and lower zones are different.The influence of the sol-air temperature on the VTGs in the upper and the lower zones is greater than that in the central zone.The characteristics of the VTGs in the three zones affected by the air supply volume are the same as those affected by the sol-air temperature.Besides,because of the small air velocity,the predicted mean vote（PMV）on comfort in the occupied zone is slightly high and the air temperature difference between the head and the ankle is usually more than 3 ℃.

Draft sensation distribution of air jet supply system in large space building in summer

To study the draft sensation distribution of an air jet supply system in a large space building in summer,experiments are conducted in a large laboratory.The temperature,velocity and draft sensation distributions at a nozzle height of 4 m in the occupied zone are obtained.Then,the numerical simulation under the test condition is carried out by the computational fluid dynamics（CFD）method.The calculation results of the indoor vertical temperature and the draft sensation distribution are validated by the test data.Simulations with different nozzle heights are conducted.The satisfactory air supply condition is determined by analyzing the draft sensations and the temperatures in the occupied zone under three conditions.The simulation results show that the optimal draft sensation distribution and the uniform temperature and velocity fields can be obtained at a nozzle height of 5 m.

Thermal stratification level of low sidewall air supply with air-conditioning system in large space

The thermal stratification level of low sidewall air supply system in large space was defined. Depending on the experiment of low sidewall air supply in summer 2008,the thermal stratification level was studied by simulation. Based on the simulation of experiment condition,the air velocity and vertical temperature distribution in a large space were simulated at different air-outlet velocities,and then the thermal stratification level line was obtained. The simulation results well match with the experimental ones and the average relative error is 3.4%. The thermal stratification level is heightened by increasing the air-outlet velocity with low sidewall air supply mode. It is concluded that when air-outlet velocity is 0.29 m/s,which is the experimental case,a uniform thermal environment in the higher occupied zone and a stable stratification level are formed. When the air-outlet velocity is low,such as 0.05 m/s,the thermal stratification level is too low and the air velocity is too small to meet the human thermal comfort in the occupied zone. So,it would be reasonable that the air-outlet velocity may be designed as 0.31 m/s if the height of the occupied zone is 2 m.

Air entrainment in a vertical dropshaft with limited air supply

Dropshafts are vertical structures widely used in urban drainage systems and buildings for water transportation.In this paper,a physical model study was conducted to investigate the air entrainment in the dropshaft under various flow regimes with and without air ventilation.Observed from the experiments,the air entrainment mechanisms varied with the water flow regimes in the dropshaft.When there was no water plug formed in the dropshaft,air could be supplied directly from downstream.Once the water plug was formed,while without venting,the air was replenished only from downstream intermittently and then in the form of large air bubble traveling upwards to the airspace at the top;while with venting,air was mainly replenished from the dropshaft top and no large air bubble was observed.The experimental results also showed that the amount of entrained air in the dropshaft with venting was greater than that without venting.

Adaptive inverse control of air supply flow for proton exchange membrane fuel cell systems

To prevent the oxygen starvation and improve the system output performance, an adaptive inverse control （AIC） strategy is developed to regulate the air supply flow of a proton exchange membrane fuel cell （PEMFC） system in this paper. The PEMFC stack and the air supply system including a compressor and a supply manifold are modeled for the purpose of performance analysis and controller design. A recurrent fuzzy neural network （RFNN） is utilized to identify the inverse model of the controlled system and generates a suitable control input during the abrupt step change of external disturbances. Compared with the PI controller, numerical simulations are performed to validate the effectiveness and advantages of the proposed AIC strategy.

Prediction Analysis on the Transport Distance of Supply Air in Warm Air Heating Room with Impinging Jet Ventilation Systems

To overcome the disadvantages of displacement ventilation( DV) and traditional mixing ventilation( MV) system,a new ventilation system known as impinging jet ventilation system( IJVS)has been developing. The warm air can be supplied with impinging jet ventilation( IJV), while the DV is only used for cooling.However,the flow and temperature field of IJV under heating scenario has had few references. The paper is mainly focused on computational fluid dynamics( CFD) and developing an adequate correlation between the distance L that warm air can reach and different parameters in the warm IJVS by using response surface methodology( RSM). The results indicate that L decreases as the supply velocity υ decreases but increases as the supply temperature difference ΔT or the discharge height h decreases. In the variable air volume( VAV) system, it is necessary to determine supply parameters both under the maximum-heat-load condition and the small-heat-load condition. Unlike the VAV system,the constant air volume( CAV) system has no need to study the small-heat-load condition. Draught discomfort near the nozzle becomes the issue of concern in IJVS, thus the suitable discharge height is of great importance in design and can be calculated based on the predictive model.

Location Problem of Air Materials Supply Center for Air Force

Based on the analysis of three influencing factors on the air material supply center location, the location model of air material supply center was established. By solving the model, the rational supply center of air materials was also determined.

半封闭温室关键系统设计与应用

半封闭温室是近年来新兴温室,其中温室气候走廊和正压送风系统是半封闭温室的关键系统设计。通过对半封闭温室内夏季温度分布的均匀性和风道风速测试试验,验证温室的降温能力和送风系统性能。试验结果表明,SFG5-4型风机配套35 m长风道,送风相对均匀,风速4.3~4.7 m/s;对于温度分布规律来说,在同一水平方向上温室内各点的平均温差1.0~1.8℃,在同一高度方向上温室内各点的平均温差2.2~3.5℃,并且3.5 m湿帘比2.0 m湿帘降温效果好。

大跨度空间非等间距喷口送风空调设计方法

针对大跨度空间负荷分布不均匀的情况,在传统射流公式法的基础上,提出了一种非等间距布置喷口的送风设计方案。结合某酒店多功能厅案例,阐述了如何根据房间负荷分布特点进行喷口的非等间距设计,并利用CFD软件对空调区温度场、速度场及热舒适性指标(PMV、PPD、DR(吹风感造成的不满意度))进行了模拟。结果表明,该方案取得了明显的改进效果,同时也验证了非等间距喷口送风设计方法的可行性。

拱架送/回风方式对日光温室冬季作物冠层区热环境的影响

传统日光温室被动的热环境调控模式难以满足温室作物冠层区空气温度和速度调控需求,且能源利用效率低下。为了改进日光温室热环境精准调控方法和提高温室能源利用效率,该研究结合日光温室围护结构特点,提出了一种日光温室拱架的送/回风方法,并基于温室作物多孔介质模型,建立了拱架送/回风系统温室的数值传热模型。采用空气温度与速度不均匀系数、气流速度适宜区面积比、能量利用系数以及累计有效积温等评价参数,研究了下送上回、中间回风和上送下回等3种温室拱架送/回风方式对日光温室冬季作物冠层区热环境的影响。结果表明,与中间回风和上送下回通风方式相比,下送上回通风方式对不同作物冠层高度处的空气温度和速度调控的结果最优,且不同作物冠层高度处气流速度适宜区面积比和累计有效积温都最大。当采用下送上回通风方式时,与送风干管风速为9、11和12 m/s相比,送风干管风速为10 m/s的能量利用系数最大,在作物冠层高度0.4、0.6、0.8和1.0 m处的能量利用系数分别为0.976、0.982、0.985和0.987,并且不同作物冠层高度处的空气温度不均匀系数和速度不均匀系数也都最小。因此,下送上回通风方式的推荐送风干管风速为10 m/s。该研究可为日光温室热环境的精准调控提供参考。

PEMFC空气系统流量和压力协同控制策略设计

为提高质子交换膜燃料电池(PEMFC)空气系统的动态响应性能,避免局部缺气而导致其输出性能降低等问题的出现,针对空气系统存在流量和压力耦合的问题,分别采用PID、前馈解耦控制和模型预测控制(MPC)对空气系统进行控制,通过仿真和台架测试,验证控制算法的有效性。结果表明,两种控制算法相比较PID均具有较好的控制效果,空气流量和空气压力均能快速跟随设定值,PEMFC发动机的输出性能平稳。

火电耦合压缩空气储能技术研究进展及展望

火电耦合压缩空气储能技术作为一种提升传统火电机组灵活性和经济性的有效手段,近年来受到了广泛关注。该文从分析火电耦合压缩空气储能技术在提升电网调峰能力、促进可再生能源整合等方面的重要意义出发。首先,介绍典型耦合系统的结构组成与工作原理;然后,探讨耦合系统中关键设备的技术现状和面临的挑战;之后,梳理火-储耦合系统的集成方案设计、调峰运行优化以及经济性评估的研究现状;最后,针对当前技术难点,展望未来火电耦合压缩空气储能技术的研究方向与重点。该文旨在为今后相关领域研究提供参考与借鉴,推动其持续发展和创新。

强制通风空浴式翅片管送风方式优化

基于FLUENT模拟研究底送顶排、顶送底排、侧送顶排、侧送底排4种送风方式对液化天然气(liquefied natural gas,LNG)空浴式翅片管气化性能的影响,采用Lee模型研究管内LNG的相变气化过程,结合管内流体温度变化分析单根翅片管气化性能受送风方式和送风速度的影响。结果表明:侧送风时翅片管周围出现低风速边界层,背风侧易形成低换热效率的尾流区;当送风速度由2.8 m/s增大到3.8 m/s和由3.8 m/s增大到4.8 m/s时,侧送底排方式下空气侧换热系数最大值分别增长3.92 W/(m^(2)·K)和2.16 W/(m^(2)·K);直送风时边界层分布均匀,最大推荐送风速度为3.2 m/s,顶送底排方式对翅片管气化性能的提升效果优于底送顶排方式;当其他条件相同时,侧送顶排为最佳送风方式;采用侧送顶排强制通风的空浴式气化器(ambient air vaporizer,AAV)气化性能显著优于自然通风AAV。

安全帽送风强度对人体呼吸微环境影响研究

为改善作业人员呼吸微环境,对送风式安全帽佩戴者呼吸微环境温度场、速度场和浓度场进行研究。通过假人试验方法测试安全帽在不同送风强度下的人体呼吸微环境温度、速度和粉尘质量浓度,研究人体呼吸微环境温度分布及速度分布规律,阐明安全帽送风强度对人体呼吸微环境中总尘及呼尘降尘效果的影响,进而分析佩戴者对安全帽送风强度的满意程度。结果显示,人体面中部位降温效果优于人体脸颊两侧,其中人体鼻子处降温效果较为明显;安全帽在不同送风强度下对人体呼吸微环境速度场的分布规律一致;当送风强度为Ⅳ级时,人体呼吸微环境内粉尘降尘效率最高,佩戴者满意率最高;人体微环境总尘和呼尘降尘效率分别可达到81.39%和82.89%。研究结果可为改善人体呼吸微环境提供参考。

激光旁轴送气结构设计与分析

目的通过了解激光增材技术,设计一种送丝送气一体化机构,并建立相应模型。方法通过对不同送丝送气机构进行对比分析,设计出3种方案,并通过流体模型分析保护气体氩气的流动情况,最终得出最合理的安装位置。第1种方案是采用送丝机构与送气机构对冲的两轴送丝送气设计方案;第2种方案是采用送丝机构与送气机构同路的设计方案;第3种方案是选择两路送气机构与送丝机成夹角对冲的设计方案。结果在第1种方案中,送丝机构与送气机构的对冲会导致气流紊乱,产生气体流动扩散现象,可以明显看到有一个保护气体比较密集的区域。在第2种方案中,当送丝机构与送气机构同路时,在工作过程中有可能出现防氧化效果不够好的情况。在第3种方案中,两路送气机构与送丝机成夹角对冲可以有效控制氩气的流动,提高氩气的利用率,在这里进行丝材的激光熔覆将会起到最大的防氧化保护作用。结论通过对不同送丝送气机构进行对比分析,最终确定三路送气方案的保护效果最佳。

数据中心冷却系统研究及应用进展

为加速实现数据中心节能降耗的目标,在合理、高效、最大化地利用自然冷源的同时,更不能忽视机械制冷系统本身能效的提升。加强自然冷却与机械制冷的协同,降低数据中心PUE,充分发挥安全稳定、高效运行的数据中心冷却系统自身能效至关重要。本文通过对气流组织、供/回水温度和冷却系统部件及形式3个方面的研究梳理,总结分析数据中心冷却系统节能提效有关技术研究与应用进展,从而为绿色、高效数据中心冷却系统的研发提供参考和借鉴。

等离子体发生器导流板结构优化研究

高效滤芯是空气净化器的关键部件,当空气净化器中流向高效滤芯部分的送风不均匀时,会导致滤芯利用率较低,从而影响滤芯的过滤性能.为提高滤芯的使用效率进而改善装置的净化性能,可以在风机和高效滤芯之间放置导流型等离子体发生器,利用发生器的导流板使送风气流更均匀的吹向滤芯.为探究适宜的导流板结构参数,采用数值模拟的方法对不同结构参数导流板下的流动过程进行分析,通过对比滤芯使用率和送风均匀性等指标,给出适宜的导流板长度和张开角度设计方案.研究结果表明,对于本文研究的净化器尺寸,导流板设计长度为100 mm、张开角度为10°时的送风更均匀.优化后的尾部导流板结构简单、设计合理、使用方便,分散了送风气流的方向,更有利于提高后端高效滤芯的利用率和使用寿命.

气垫带式输送机供气方式改进

气垫带式输送机因为将传统滚动摩擦替换为空气摩擦,所以总功率应该小于普通带式输送机,然而实际中功率消耗并不小。存在原因有供风方式不合适,造成很大的能量损耗,甚至出现空载飘带现象。通过改变供风方式,可以合理控制风压和风量,使输送带能够平稳支撑并运行。在保证气室大小及形状及总流量不变,只改变入口数量的情况下,通过ANSYS分析不同供气情况下气膜的压力分布情况,结果显示分流后气膜压力显著增大。

HTR-PM汽轮机轴封蒸汽断供原因分析及解决方案

介绍了高温气冷堆示范工程(HTR-PM)汽轮机轴封系统,并且对轴封蒸汽断供的原因进行了分析,提出了可以采用蒸汽发生器及管道内余汽供轴封、辅助电锅炉至轴封供汽管道改造、高温空气供轴封这3种解决方案。对3种方案进行对比,分析其在成本、可靠性和运行限制方面的优缺点,结果表明3种方案均是可行的。研究结果为HTR-PM汽轮机轴封蒸汽断供问题的解决提供了参考。