Efficient unequal error protection for online fountain codes

In this paper,an efficient unequal error protection(UEP)scheme for online fountain codes is proposed.In the buildup phase,the traversing-selection strategy is proposed to select the most important symbols(MIS).Then,in the completion phase,the weighted-selection strategy is applied to provide low overhead.The performance of the proposed scheme is analyzed and compared with the existing UEP online fountain scheme.Simulation results show that in terms of MIS and the least important symbols(LIS),when the bit error ratio is 10-4,the proposed scheme can achieve 85%and 31.58%overhead reduction,respectively.

Regularity classification and corresponding analysis method requirements of horizontally curved bridges with unequal pier heights

The seismic behavior of horizontally curved bridges,particularly with unequal height piers,is more complicated than that of straight bridges due to their geometric properties.In this study,the seismic responses of several horizontally curved single-column-bent viaducts with various degrees of curvature and different pier heights have been investigated,employing three different analysis approaches:namely,modal pushover analysis,uniform load method,and nonlinear time history analysis.Considering the investigated bridge configurations and utilizing the most common regularity indices,the results indicate that viaducts with 45-degree and 90-degree deck subtended angles can be categorized as regular and moderately irregular,respectively,while the bridges with 180-degree deck subtended angle are found to be highly irregular.Furthermore,the viaducts whose pier heights are asymmetric may be considered as irregular for almost all ranges of the deck subtended angles.The effects of higher transverse and longitudinal modes are discussed and the minimum analysis requirements are identified to assess the seismic response of such bridge configurations for design purposes.Although the Regularity Indices used here are useful tools to distinguish between regular and irregular bridges,further studies are needed to improve their reliability.

Research on friction stir welding of 5754 aluminum alloy with unequal thickness

A new structure of 1+2 was designed in friction stir welding(FSW)of Al alloy sheet with unequal thickness:a specific sheet with similar composition of base metals(BMs)was placed under the thinner sheet as the supporting sheet so that the BM surfaces could be on a plane.The BMs can also be fully penetrated weld with a stirring pin longer than the thickness of the thin sheet.2 mm and 1.5 mm thick Al alloy sheets were welded by FSW,and parameters were optimized.The highest welding strength reached 96.07%of the thin base metal.Although a slight thinning phenomenon occurred at the edge of the nugget on the retreating side,the specimen still fractured in the heat-af-fected zone.

Design of Evolutionary Algorithm Based Unequal Clustering for Energy Aware Wireless Sensor Networks

Wireless Sensor Networks(WSN)play a vital role in several real-time applications ranging from military to civilian.Despite the benefits of WSN,energy efficiency becomes a major part of the challenging issue in WSN,which necessitate proper load balancing amongst the clusters and serves a wider monitoring region.The clustering technique for WSN has several benefits:lower delay,higher energy efficiency,and collision avoidance.But clustering protocol has several challenges.In a large-scale network,cluster-based protocols mainly adapt multi-hop routing to save energy,leading to hot spot problems.A hot spot problem becomes a problem where a cluster node nearer to the base station(BS)tends to drain the energy much quicker than other nodes because of the need to implement more transmission.This article introduces a Jumping Spider Optimization Based Unequal Clustering Protocol for Mitigating Hotspot Problems(JSOUCP-MHP)in WSN.The JSO algorithm is stimulated by the characteristics of spiders naturally and mathematically modelled the hunting mechanism such as search,persecution,and jumping skills to attack prey.The presented JSOUCPMHP technique mainly resolves the hot spot issue for maximizing the network lifespan.The JSOUCP-MHP technique elects a proper set of cluster heads(CHs)using average residual energy(RE)to attain this.In addition,the JSOUCP-MHP technique determines the cluster sizes based on two measures,i.e.,RE and distance to BS(DBS),showing the novelty of the work.The proposed JSOUCP-MHP technique is examined under several experiments to ensure its supremacy.The comparison study shows the significance of the JSOUCPMHP technique over other models.

Energy Efficient Unequal Fault Tolerance Clustering Approach

For achieving Energy-Efficiency in wireless sensor networks(WSNs),different schemes have been proposed which focuses only on reducing the energy consumption.A shortest path determines for the Base Station(BS),but fault tolerance and energy balancing gives equal importance for improving the network lifetime.For saving energy in WSNs,clustering is considered as one of the effective methods for Wireless Sensor Networks.Because of the excessive overload,more energy consumed by cluster heads(CHs)in a cluster based WSN to receive and aggregate the information from member sensor nodes and it leads to failure.For increasing the WSNs’lifetime,the CHs selection has played a key role in energy consumption for sensor nodes.An Energy Efficient Unequal Fault Tolerant Clustering Approach(EEUFTC)is proposed for reducing the energy utilization through the intelligent methods like Particle Swarm Optimization(PSO).In this approach,an optimal Master Cluster Head(MCH)-Master data Aggregator(MDA),selection method is proposed which uses the fitness values and they evaluate based on the PSO for two optimal nodes in each cluster to act as Master Data Aggregator(MDA),and Master Cluster Head.The data from the cluster members collected by the chosen MCH exclusively and the MDA is used for collected data reception from MCH transmits to the BS.Thus,the MCH overhead reduces.During the heavy communication of data,overhead controls using the scheduling of Energy-Efficient Time Division Multiple Access(EE-TDMA).To describe the proposed method superiority based on various performance metrics,simulation and results are compared to the existing methods.

Anti-plane Analysis of a Circular Hole withThree Unequal Cracks in One-dimensionalHexagonal Piezoelectric Quasicrystals

This paper employes variable function method and the technique of conformal mappingto discuss the anti-plane problem of a circular hole with three unequal cracksin a one-dimensional （1D） hexagonal piezoelectric quasicrystal. Based on the piezoelectricityfundamental equations of quasicrystal materials and the symmetry of1D hexagonal quasicrystal and its linear piezoelectricity effect, 1D hexagonal quasicrystalcontrol equations of anti-plane problem are derived. Applying Cauchyintegral formula, the analytical expressions for the crack tip filed intensity factorsare presented with the assumption that the crack are electrical impermeable andelectrical permeable. With the variation of the hole-size and the crack length, someof the new model of crack are obtained. In the absence of the electric load, theresults match with the classical ones. The numerical results indicate the effects ofgeometric parameters on the field intensity factors. It is verified that the horizontalcrack length and the circle radius can easily promote crack growth. Researchon such issues will provide reliable theoretical value for the engineering materialspreparation and application.

Study on inhomogeneous cooling behavior of extruded profile with unequal and large thicknesses during quenching using thermo-mechanical coupling model

The interfacial heat transfer coefficient between hot profile surface and cooling water was determined by using inverse heat conduction model combined with end quenching experiment. Then, a Deform-3 D thermo-mechanical coupling model for simulating the on-line water quenching of extruded profile with unequal and large thicknesses was developed. The temperature field, residual stress field and distortion of profile during quenching were investigated systematically. The results show that heat transfer coefficient increases as water flow rate increases. The peak heat transfer coefficient with higher water flow rates appears at lower interface temperatures. The temperature distribution across the cross-section of profile during quenching is severe nonuniform and the maximum temperature difference is 300 ℃ at quenching time of 3.49 s. The temperature difference through the thickness of different parts of profile first increases sharply to a maximum value, and then gradually decreases. The temperature gradient increases obviously with the increase of thickness of parts. After quenching, there exist large residual stresses on the inner side of joints of profile and the two ends of part with thickness of 10 mm. The profile presents a twisting-type distortion across the cross-section under non-uniform cooling and the maximum twisting angle during quenching is 2.78°.

Improved unequal interval grey model and its applications

A new method to improve prediction precision of GM（1,1） model with unequal time interval is presented.The grey derivative is multiplied by a parameter to guarantee the time response function satisfying approximately exponential function distribution.To simplify the process of parametric estimation,an approximate value is taken for the multiplied parameter.Then the estimators of coefficient of development and grey action quantity can be derived.At the same time,the principle of the new information priority is also considered.We take the last item of the first-order accumulated generation operator（1-AGO） on raw data sequence as the initial condition in the time response function.Then the new information can be taken full advantage of through the improved initial condition.Some properties of this new model are also discussed.The presented method is actually a combination of improvement of grey derivative and improvement of the initial condition.The results of an example indicate that the proposed method can improve prediction precision prominently.

An analytical solution for the stress field and stress intensity factor in an infinite plane containing an elliptical hole with two unequal aligned cracks

The existing analytical solutions are extended to obtain the stress fields and the stress intensity factors(SIFs) of two unequal aligned cracks emanating from an elliptical hole in an infinite isotropic plane. A conformal mapping is proposed and combined with the complex variable method. Due to some difficulties in the calculation of the stress function, the mapping function is approximated and simplified via the applications of the series expansion. To validate the obtained solution, several examples are analyzed with the proposed method, the finite element method, etc. In addition, the effects of the lengths of the cracks and the ratio of the semi-axes of the elliptical hole(a/b) on the SIFs are studied. The results show that the present analytical solution is applicable to the SIFs for small cracks.

EFFECT OF UNEQUAL DEFORMATION IN DEVELOPMENT OF ADVANCED PLASTIC PROCESSING TECHNOLOGIES

An effect of unequal deformation in development of advanced plasticprocessing technologies is researched by studying an in-plane bending process of strip metal underunequal compressing. The research results show the following: If appropriately controlled, unequalplastic deformation can play an important role not only in the improvement of quality of partsobtained by plastic processing technologies, but also in the development of new processes foradvanced plastic working technologies. A coordinated growth of unequal plastic deformation candevelop the deformation potentiality of material to the fall. The degree of unequal plasticdeformation can be used as bases for optimization design of processes and dies of plastic forming.

Experimental Study on the Flow Around Two Tandem Cylinders with Unequal Diameters

In this paper, flow around two circular cylinders in tandem arrangement with unequal diameters has been investigated using the particle image velocimetry technique(PIV) in a water channel. The upstream to downstream diameter ratio was kept constant at d/D = 2/3, the centre-to-centre distance was varied from 1.2D to 5D and the Reynolds number was varied from 1200 to 4800. The flow characteristics were analyzed through ensemble-averaged patterns of velocity, vorticity, normalized Reynolds stress contours and streamlines. Based on ensemble-averaged and instantaneous flow fields, different flow patterns, including single-wakeshedding at small spacing ratio, bi-stable flow behavior(alternating behavior of reattachment and vortex shedding) at intermediate spacing ratio and co-shedding pattern at large spacing ratio were observed. The effects of Reynolds number and the centre-to-centre spacing ratio on flow patterns and turbulent characteristics were also investigated. It was found that the diameter ratio appears to have a certain effect on the flow patterns at intermediate spacing ratios, where the reattachment of shear layer depends on the lateral width of the wake flow in the lee of the upstream cylinder. Extensive discussion on the distributions of Reynolds stress and turbulent kinetic energy was presented.

Joint resource allocation for MIMO-OFDM video transmission systems with unequal error protection

To improve the performance of MIMO-OFDM video transmission systems on the limitation of wireless bandwidth and transmitting power,we propose an adaptive joint resource allocation algorithm with unequal error protection(UEP) based on joint source-channel coding(JSCC) according to H.264 video compression standard and RCPT channel coding.According to different thresholds of the average SNR of subchannels,the algorithm dynamically allocates the source coding parameters of original video data and the channel coding parameters of RCPT,which realizes UEP for the compressed video data of different importance.Through the bit and power allocation based on MQAM modulation and the subspace allocation based on beamforming technology for different subcarriers,an adaptive joint resource allocation making full use of space-frequency domain resources have been realized.The simulation results indicate that the algorithm improves the adaptability of video transmission systems in different wireless environments and the quality of video retrieval.

Response of Two Unequal-Diameter Flexible Cylinders in A Side-by-Side Arrangement:Characteristics of FIV

Till now,little information is available on the flow-induced vibration(FIV)of multiple flexible cylinders with unequal diameters.Some FIV characteristics of unequal-diameter cylinders can be predicted based on the knowledge of equal-diameter cylinders,while there are still other features remaining unrevealed.In this paper,the FIV characteristics of two flexible cylinders with unequal diameters arranged side-by-side are experimentally investigated.The diameter ratio of the small cylinder(Small Cyl.)to the large cylinder(Large Cyl.)is nearly 0.5.The aspect ratios and mass ratios of the two flexible cylinders are 350/181 and 1.90/1.47,respectively.The centre-tocentre spacing ratio in the cross-flow(CF)direction is kept constant as 6.0 and the two cylinders can oscillate freely in both the CF and in-line(IL)directions.The towing velocity varies from 0.05 m/s to 1.00 m/s.The dominant modes and frequencies,CF and IL displacement amplitudes and response trajectories are discussed.Compared with the case of two identical cylinders in our previous study,the FIV responses demonstrate some similarities and differences.The similarities are as follows.Both cylinders exhibit multi-mode vibration features and they interact with each other.Meanwhile,the IL FIV shows a more complex behaviour than that in the CF direction.The difference is that as the diameter of one cylinder is increased,the effect on the smaller cylinder becomes more significant.For Large Cyl.,the FIV response is similar to its isolated counterpart,which indicates that Small Cyl.has a negligible effect on the FIV of the larger one.Whereas Large Cyl.perplexes the FIV of Small Cyl.during the vibration process.The spacing would change when both cylinders are oscillating.Proximity interference between the two cylinders and wake shielding effect of the Large Cyl.may occur.The dominant frequencies of Small Cyl.are reduced and the wake-induced flutter of Small Cyl.is observed from the response trajectories at different measuring points.

Heat transfer analysis and experimental study of unequal diameter twin-roll casting process for fabricating Cu/Al clad strips

Unequal diameter twin-roll casting(UDTRC)can improve the formability,surface conditions,and production efficiency during the fabrication of clad strips.Using Fluent software,a numerical simulation is used to study the asymmetric heat transfer characteristics of Cu/Al clad strips fabricated by UDTRC.The effects of roller velocity ratio,Cu strip thickness,and inclination angle on the kissing point position,as well as the entire temperature distribution are obtained.The heat transfer model is established,and the mechanism is discussed.The Cu strip and rollers are found to be the main causes of asymmetric heat transfer,indicating that the roller velocity ratio changes the liquid zone proportion in the molten pool.The Cu strip thickness determines the heat absorption capacity and the variations in thermal resistance between the molten Al and the big roller.The inclination angle of the small roller changes the cooling time of big roller to molten Al.Moreover,the microstructure of Al cladding under different roller velocity ratios is examined.The results show significant grain refinement caused by the shear strain along the thickness direction of Al cladding and the intense heat transfer at the moment of contact between the metal Al cladding and Cu strip.

Availability-based maintenance optimization under unequal inspection period and imperfect repair

Taking the multi-component system as research object, a maintenance optimization model based on the unequal inspection period and imperfect repair is established by considering the requirement of expected availability for improving the system＇s availability. An age reduction factor is used to describe the effect of imperfect repair, and the modelling approach for the unequal inspection period is proposed. Unavailable situations are classified into three kinds of independent cases, and the availability is calculated accordingly. Based on the analysis of the relationship between the unavailable cases and the unequal inspection period, an optimization model under imperfect repair is established to optimize the system＇s expected availability. A case study of a wind turbine is provided, and three key components, i.e. gearbox, generator and spindle, are considered. The optimization results of the unequal inspection period model and the equal inspection period model are compared. The results show that the unequal inspection period model based on availability can update the maintenance plan so as to optimize maintenance activities and improve the system＇s availability.

Scattering of Oblique Water Waves by Two Unequal Surface-Piercing Vertical Thin Plates with Stepped Bottom Topography

Based on linear water-wave theory, this study investigated the scattering of oblique incident water waves by two unequal surface-piercing thin vertical rigid plates with stepped bottom topography. By using the matched eigenfunction expansion method and a least square approach, the analytical solutions are sought for the established boundary value problem. The effects of the incidence angle, location of step, depth ratio of deep to shallow waters,and column width between two plates, on the reflection coefficients, the horizontal wave forces acting on the two plates, and the mean surface elevation between the two plates, are numerically examined under a variety of wave conditions. The results show that the existence of the stepped bottom between two plates considerably impacts the hydrodynamic performances of the present system. It is found that the effect of stepped bottom on the reflection coefficient of the present two-plate structure is evident only with waves of the low dimensionless frequency.Moreover, the influence of the step location on the hydrodynamic performance of the present two-plate structure is slight if the step is placed in between the two plates.

An unequal clustering routing protocal for wireless sensor networks based on genetic algorithm

The imbalance of energy consumption in wireless sensor networks(WSNs)easily results in the“hot spot”problem that the sensor nodes in a particular area die due to fast energy consumption.In order to solve the“hot spot”problem in WSNs,we propose an unequal clustering routing algorithm based on genetic algorithm(UCR-GA).In the cluster head election phase,the fitness function is constructed based on the residual energy,density and distance between nodes and base station,and the appropriate node is selected as the cluster head.In the data transmission phase,the cluster head selects single-hop or multi-hop communication mode according to the distance to the base station.After we comprehensively consider the residual energy of the cluster head and its communication energy consumption with the base station,an appropriate relay node is selected.The designed protocal is simulated under energy homogeneous and energy heterogeneity conditions,and the results show that the proposed routing protocal can effectively balance energy consumption,prolong the life cycle of network,and is appicable to heterogeneous networks.

A Coverage-Aware Unequal Clustering Protocol with Load Separation for Ambient Assisted Living Based on Wireless Sensor Networks

Ambient Assisted Living(AAL) is becoming an important research field. Many technologies have emerged related with pervasive computing vision, which can give support for AAL. One of the most reliable approaches is based on wireless sensor networks(WSNs). In this paper, we propose a coverage-aware unequal clustering protocol with load separation(CUCPLS) for data gathering of AAL applications based on WSNs. Firstly, the coverage overlap factor for nodes is introduced that accounts for the degree of target nodes covered. In addition, to balance the intra-cluster and inter-cluster energy consumptions, different competition radiuses of CHs are computed theoretically in different rings, and smaller clusters are formed near the sink. Moreover, two CHs are selected in each cluster for load separation to alleviate the substantial energy consumption difference between a single CH and its member nodes. Furthermore, a backoff waiting time is adopted during the selection of the two CHs to reduce the number of control messages employed. Simulation results demonstrate that the CUCPLS not only can achieve better coverage performance, but also balance the energy consumption of a network and prolong network lifetime.

Joint DOA and polarization estimation for unequal power sources based on reconstructed noise subspace

In most literature about joint direction of arrival（DOA） and polarization estimation, the case that sources possess different power levels is seldom discussed. However, this case exists widely in practical applications, especially in passive radar systems. In this paper, we propose a joint DOA and polarization estimation method for unequal power sources based on the reconstructed noise subspace. The invariance property of noise subspace（IPNS） to power of sources has been proved an effective method to estimate DOA of unequal power sources. We develop the IPNS method for joint DOA and polarization estimation based on a dual polarized array. Moreover, we propose an improved IPNS method based on the reconstructed noise subspace, which has higher resolution probability than the IPNS method. It is theoretically proved that the IPNS to power of sources is still valid when the eigenvalues of the noise subspace are changed artificially. Simulation results show that the resolution probability of the proposed method is enhanced compared with the methods based on the IPNS and the polarimetric multiple signal classification（MUSIC） method. Meanwhile, the proposed method has approximately the same estimation accuracy as the IPNS method for the weak source.

On the Unequal Relationship in “The Short Happy Life of Francis Macomber” from the Perspective of Discourse Framework

"The Short Happy Life of Francis Macomber",is a representative short story of Hemingway since it clearly embodies hisprinciple of creation.To illustrate the unequal relationship between the hero Macomber and the heroine Margot,this paper employsBurton’s(1980)Discourse Framework theory to analyze the distribution,classification and pattern of these two characters’chal-lenging moves.On the basis of the dialogue analysis,the author attempts to analyze the patterns of their challenging moves,whichcan reflect Macomber is in a more inferior position in marriage than his wife.And the reasons for this are Margot not only holdsmany challenging moves but also seizes the speaking rights in communication.