Performance Analysis of Intelligent Reflecting Surface Assisted Wireless Communication System

In this paper,we investigate the end-to-end performance of intelligent reflecting surface(IRS)-assisted wireless communication systems.We consider a system in which an IRS is deployed on a uniform planar array(UPA)configuration,including a large number of reflecting elements,where the transmitters and receivers are only equipped with a single antenna.Our objective is to analytically obtain the achievable ergodic rate,outage probability,and bit error rate(BER)of the system.Furthermore,to maximize the system’s signal-to-noise ratio(SNR),we design the phase shift of each reflecting element and derive the optimal reflection phase of the IRS based on the channel state information(CSI).We also derive the exact expression of the SNR probability density function(p.d.f.)and show that it follows a non-central Chi-square distribution.Using the p.d.f.,we then derive the theoretical results of the achievable rate,outage probability,and BER.The accuracy of the obtained theoretical results is also verified through numerical simulation.Itwas shown that the achievable rate,outage probability,and BER could be improved by increasing the number of reflecting elements and choosing an appropriate SNR regime.Furthermore,we also find that the IRS-assisted communication system achieves better performance than the existing end-to-end wireless communication.

The patterns of surface capillary-gravity short-crested waves with uniform current fields in coastal waters

A fully three-dimensional surface gravitycapillary short-crested wave system is studied as two progressive wave-trains of equal amplitude and frequency, which are collinear with uniform currents and doubly-periodic in the horizontal plane, are propagating at an angle to each other. The first- and second-order asymptotic analytical solutions of the short-crested wave system are obtained via a perturbation expansion in a small parameter associated with the wave steepness, therefore depicting a series of typical three-dimensional wave patterns involving currents, shallow and deep water, and surface capillary waves, and comparing them with each other.

The effect of pulse voltage rise rate on the polypropylene surface hydrophilic modification by ns pulsed nitrogen DBD

The nanosecond(ns) pulsed nitrogen dielectric barrier discharge(DBD) is employed to enhance the hydrophilicity of polypropylene(PP) surface and improve its application effect.The discharge characteristics of the ns pulsed nitrogen DBD with different pulse rise times(from 50to 500 ns) are investigated by electrical and optical diagnostic methods and the discharge uniformity is quantitatively analyzed by image processing method.To characterize the surface hydrophilicity,the water contact angle(WCA) is measured,and the physical morphology and chemical composition of PP before and after modification are analyzed to explore the effect of plasma on PP surface.It is found that with increasing pulse rise time from 50 to 500 ns,DBD uniformity becomes worse,energy efficiency decreases from 20% to 10.8%,and electron density decrease from 6.6 × 10^(11)to 5.5 × 10^(11)cm^(-3).The tendency of electron temperature is characterized with the intensity ratio of N_(2)/N_(2)^(+)emission spectrum,which decreases from 17.4 to15.9 indicating the decreasing of T_(e) with increasing pulse rise time from 50 to 500 ns.The PP surface treated with 50 ns pulse rise time DBD has a lower WCA(~47°),while the WCA of PP treated with 100 to 500 ns pulse rise time DBD expands gradually(~50°–57°).According to the study of the fixed-point WCA values,the DBD-treated PP surface has superior uniformity under50 ns pulse rise time(3° variation) than under 300 ns pulse rise time(8° variation).After DBD treatment,the increased surface roughness from 2.0 to 9.8 nm and hydrophilic oxygencontaining groups on the surface,i.e.hydroxyl(-OH) and carbonyl(C=O) have played the significant role to improve the sample’s surface hydrophilicity.The short pulse voltage rise time enhances the reduced electric field strength(E/n) in the discharge space and improves the discharge uniformity,which makes relatively sufficient physical and chemical reactions have taken place on the PP surface,resulting in better treatment uniformity.

Ship hull plate processing surface fairing with constraints based on B-spline

The problem of ship hull plate processing surface fairing with constraints based on B-spline is solved in this paper. The algorithm for B-spline curve fairing with constraints is one of the most common methods in plane curve fairing. The algorithm can be applied to global and local curve fairing. It can constrain the perturbation range of the control points and the shape variation of the curve, and get a better fairing result in plane curves. In this paper, a new fairing algorithm with constraints for curves and surfaces in space is presented. Then this method is applied to the experiments of ship hull plate processing surface. Finally numerical results are obtained to show the efficiency of this method.

Approximate merging of B-spline curves and surfaces

Applying the distance function between two B-spline curves with respect to the L2 norm as the approximate error, we investigate the problem of approximate merging of two adjacent B-spline curves into one B-spline curve. Then this method can be easily extended to the approximate merging problem of multiple B-spline curves and of two adjacent surfaces. After minimizing the approximate error between curves or surfaces, the approximate merging problem can be transformed into equations solving. We express both the new control points and the precise error of approximation explicitly in matrix form. Based on homogeneous coordinates and quadratic programming, we also introduce a new framework for approximate merging of two adjacent NURBS curves. Finally, several numerical examples demonstrate the effectiveness and validity of the algorithm.

Turbulent Variance Characteristics of Temperature and Humidity over a Non-uniform Land Surface for an Agricultural Ecosystem in China

This paper describes the application of the variance method for flux estimation over a mixed agricultural region in China. Eddy covariance and flux variance measurements were conducted in a near-surface layer over a non-uniform land surface in the central plain of China from 7 June to 20 July 2002. During this period, the mean canopy height was about 0.50 m. The study site consisted of grass （10% of area）, beans （15%）, corn （15%） and rice （60%）. Under unstable conditions, the standard deviations of temperature and water vapor density （normalized by appropriate scaling parameters）, observed by a single instrument, followed the Monin-Obukhov similarity theory. The similarity constants for heat （CT） and water vapor （Cq） were 1.09 and 1.49, respectively. In comparison with direct measurements using eddy covariance techniques, the flux variance method, on average, underestimated sensible heat flux by 21% and latent heat flux by 24%, which may be attributed to the fact that the observed slight deviations （20% or 30% at most） of the similarity ＂constants＂ may be within the expected range of variation of a single instrument from the generally-valid relations.

Reconstruction of B-spline surface by interpolating boundary curves and approximating inner points

In this paper, we present an algorithm for reconstruction of B-spline surface such that it interpolates the four given bound- ary curves and simultaneously approximates some given inner points. The main idea of our method is： first, we construct an initial surface which interpolates the four given boundary curves; then, while keeping the boundary control points of the initial surface un- changed, we reposition the inner control points of the surface with energy optimization method. Examples show that our algorithm is practicable and effective.

Symmetric alteration of four knots of B-spline and NURBS surfaces

Modifying the knots of a B-spline curve, the shape of the curve will be changed. In this paper, we present the effect of the symmetric alteration of four knots of the B-spline and the NURBS surfaces, i.e., symmetrical alteration of the knots of surface, the extended paths of points of the surface will converge to a point which should be expressed with several control points. This theory can be used in the constrained shape modification of B-spline and NURBS surfaces.

G^0 and G^1 connection between two adjacent B-spline surfaces

In this paper, the smooth connection between two B-spline surfaces is discussed. First, a brief proof of some simple sufficient conditions of Go and G1 continuity is given. On this basis, a novel method for Go or G1 connection between two adjacent B-spline surfaces is presented. A reparameterization step is firstly taken for one of the surfaces such that they have the same parameterization in v direction, then, adjust their boundary control vertices to make them Go or Gl connected. The GI connection parameter is determined by an optimization problem. Compared with the existed methods, our method is simple and easy to be used in practice.

B-Spline Approximation of Ship Waves on the Free Surface

We consider the problem of a ship advancing in waves. In this method, the zone of free surface in the vicinity of body is discretized. On the discretized surface, the first-order and second-order derivatives of ship waves are represented by the B-Spline formulae. Different ship waves are approximated by cubic B-spline and the first and second order derivates of incident waves are calculated and compared with analytical value. It approves that this numerical method has sufficient accuracy and can be also applied to approximate the velocity potential on the free surface.

G^1 Continuity Conditions of B-spline Surfaces

According to the B-spline theory and Boehm algorithm, this paper presents several necessary and sufficient G1 continuity conditions between two adjacent B-spline surfaces. In order to meet the need of application, a kind of sufficient conditions of G1 continuity are developed, and a kind of sufficient conditions of G1 continuity among N(N>2) patch B-spline surfaces meeting at a common corner are given at the end.

RECONSTRUCTION OF SYMMETRIC B-SPLINE CURVES AND SURFACES

A method to reconstruct symmetric B-spline curves and surfaces is presented. The symmetry property is realized by using symmetric knot vector and symmetric control points. Firstly, data points are divided into two parts based on the symmetry axis or symmetry plane extracted from data points. Then the divided data points are parameterized and a symmetric knot vector is selected in order to get symmetric B-spline basis functions. Constraint equations regarding the control points are deduced to keep the control points of the B-spline curve or surface to be symmetric with respect to the extracted symmetry axis or symmetry plane. Lastly, the constrained least squares fitting problem is solved with the Lagrange multiplier method. Two examples from industry are given to show that the proposed method is efficient, robust and able to meet the general engineering requirements.

Fast B-spline surface extraction algorithm of seismic volume data on GPU

In the process of seismic data interpretation, the extraction of a horizon or a fault is generally needed. In this paper we present a fast extraction method. First select some feature points interactively, then reconstruct the surface according to the selected feature points by using B-spline interpolation curve or surface. In order to solve the error-drawing problem appeared in the process of interactive rendering, which is caused by the change of sampling interval as the view point changes, we combine shear-warp and splatting algorithm to render the surface. The rendering of seismic data and specific surface in our work are achieved on GPU platform using CUDA programming language, which make it able to meet the requirements of real-time rendering.

Modification of B-Spline Surfaces with Optimization

Algorithms of modifying a surface to approximate some scattered points, or pass through some characteristic points/curves are presented. Similar to variational approach, the algorithms are based on optimization. For the deviation between the modified surface and the original one is adopted as the objective functions, the change of the surface shape is as small as possible with the modified surface satisfying the specified requirements.

B-SPLINE SURFACE SMOOTH JOINING

Optimization techniques are being applied to solve the problems of surface interpolation, approximation, smooth joining and fairing, aiming at corresponding objective functions. This paper focuses on the construction of fair surface interpolating the given mesh of curved boundaries with G 2 adjustment at comers and G 1, G 2 smoothness between adjacent patches. Many papers on surface blending have been presented, but almost all of them are restricted to the discussion of Bezier patches, there are no good results for B-spline surface. This paper gives a solution to the B-spline surface, allowing the surface to degenerate at comer in and have different parameterization along the common boundary of two patches.

An Algorithm of B-Spline Surface Interpolation

A surface interpolation algorithm is presented. By using a special kind of knot vector. a B-spline surface can be constructed to interpolate an array of m ×n positions, including parameter u and v tangent vectors and twist vector at each positions. Single surface interpolation approach is easier to ensure the smoothness of the interpolating surface than multi-patches method. This algorithm can be used to solve the approximating problem of B-spline approximation of general parametric surface.

An improved adaptive response surface method for structural reliability analysis

The response surface method(RSM) is one of the main approaches for analyzing reliability problems with implicit performance functions.An improved adaptive RSM based on uniform design(UD) and double weighted regression(DWR) was presented.In the proposed method,the basic principle of the iteratively adaptive response surface method is applied.Uniform design is used to sample the fitting points.And a double weighted regression system considering the distances from the fitting points to the limit state surface and to the estimated design points is set to determine the coefficients of the response surface model.Compared with the conventional approaches,the fitting points selected by UD are more representative,and a better approximation in the key region is also observed with DWR.Numerical examples show that the proposed method has good convergent capability and computational accuracy.

Trend surface analysis of forest landscape pattern in Guandishan forest region of Shanxi,China

Landscape pattern is a widely used concept for the demonstration of landscape characteristic features. The integral spatial distribution trend of landscape elements is interested point in the landscape ecological research, especially in those of complex secondary forest regions with confusing mosaics of land cover. Trend surface analysis which used in community and population ecological researches was introduced to reveal the landscape pattern. A reasonable and reliable approach for application of trend surface analysis was provided in detail. As key steps of the approach, uniform grid point sampling method was developed. The efforts were also concentrated at an example of Guandishan forested landscape. Some basic rules of spatial distribution of landscape elements were exclaimed. These will be benefit to the further study in the area to enhance the forest sustainable management and landscape planning.

Geometry Modeling of Ship Hull Based on Non-uniform B-spline

In order to generate the three-dimensional (3-D) hull surface accurately and smoothly,a mixed method which is made up of non-uniform B-spline together with an iterative procedure was developed.By using the iterative method the data points on each section curve are calculated and the generalized waterlines and transverse section curves are determined.Then using the non-uniform B-spline expression,the control vertex net of the hull is calculated based on the generalized waterlines and section curves.A ship with tunnel stern was taken as test case.The numerical results prove that the proposed approach for geometry modeling of 3-D ship hull surface is accurate and effective.

NURBS Parameterization for Medical Surface Reconstruction

InVesalius is an open-source software for reconstruction of computed tomography and magnetic resonance images, which allows the user to make analysis and segmentation of virtual anatomical models. Physical models can be printed with the aid of rapid prototyping, giving the medical community a reliable instrument to help planning surgeries. To offer the user more control over the model, this work describes a methodology and tool developed for NURBS parameterization that provides mechanisms for adjusting the shape or even selecting a particular region of interest of the surface. Furthermore, the tool gives the option to export the final results of the process to a STEP file, which allows further edition in any well-known CAD software.