Cobalt sulphides attract much attention as anode materials for Li-ion batteries(LIBs).However,its poor conductivity,low initial column efficiency and large volume changes during cycling have hindered its further devel...Cobalt sulphides attract much attention as anode materials for Li-ion batteries(LIBs).However,its poor conductivity,low initial column efficiency and large volume changes during cycling have hindered its further development.Herein,novel interlaced CoS nanosheets were firstly prepared on Carbon Fiber Cloth(CFC)by two hydrothermal reactions followed with carbon coating via carbonizing dopamine(CoS NS@C/CFC).As a freestanding anode,the nanosheet structure of CoS not only accommodates the volume variation,but also provides a large interface area to proceed the charge transfer reaction.In addition,CFC works as both a three-dimensional skeleton and an active substance which can further improve the areal capacity of the resulting electrode.Furthermore,the coated carbon combined with the CFC work as a 3D conductive network to facilitate the electron conduction.The obtained CoS NS@C/CFC,and the contrast sample prepared with the same procedure but without carbon coating(CoS NS/CFC),are characterized with XRD,SEM,TEM,XPS and electrochemical measurements.The results show that the CoS NS@C/CFC possesses much improved electrochemical performance due to the synergistic effect of nanosheet CoS,the coated carbon and the CFC substrate,exhibiting high initial columbic efficiency(~87%),high areal capacity(2.5 at 0.15 mA cm−2),excellent rate performance(1.6 at 2.73 mA cm−2)and improved cycle stability(87.5%capacity retention after 300 cycles).This work may provide a new route to explore freestanding anodes with high areal specific capacity for LIBs.展开更多
This study focuses on designing a solution to the perennial issue of clothing fit in Fashion Industry using tools offered by digital technology and statistical analysis, in particular, the data gathered on Asian women...This study focuses on designing a solution to the perennial issue of clothing fit in Fashion Industry using tools offered by digital technology and statistical analysis, in particular, the data gathered on Asian women (Bangladeshi and Chinese). The study reveals that managing information can significantly enhance the capability of the industry to cater to the needs of its consumers and increase diversity. It centers on the effectiveness of turning dressmaking patterns into digital ones, thus transecting from traditional cutting and stitching to remote techniques. This entails the requirement to have correct self-measures and probable errors, which can arise in the process. Thus, with the help of regression analysis, the study identifies, which measurements are incorrect and influence the fit of the clothes, and, therefore, digital pattern creation is more accurate. Altogether, it can be observed how digitalization and statistical methods are crucial to transforming the way clothes are created to approach an ideal standard of measurements that fulfill every customer’s needs to make operational and efficient the clothing sector.展开更多
This study aimed to comprehensively investigate the essential considerations in designing adaptive clothing for women with lower limb prostheses in Saudi Arabia. Employing a qualitative methodology, the research entai...This study aimed to comprehensively investigate the essential considerations in designing adaptive clothing for women with lower limb prostheses in Saudi Arabia. Employing a qualitative methodology, the research entailed semi-structured, in-depth interviews with women utilizing lower limb prostheses and prosthetic specialists. This approach was selected to unearth pivotal design prerequisites and comprehend the specific challenges these women encounter within the realm of clothing. The utilization of selective sampling facilitated the collection of intricate and valuable insights. A Functional, Expressive, and Aesthetic (FEA) User Needs model was utilized to scrutinize participant feedback. Functional requisites encompass ease of dressing and undressing, accessibility to the prosthetic limb, comfort, mobility with the prosthesis, and appropriate fit. Additionally, participants highlighted various expressive needs, including privacy preservation, modesty, camouflaging disability appearances, maintaining alignment with non-disabled women’s fashion, and considerations about the aesthetic aspects of garments.展开更多
Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performa...Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.展开更多
Micro-honeycomb ceramics were successfully fabricated through brush-coating with cloth fabric as pore-forming agent. The influence of pore-forming agent and slurry’s moisture content on the micro-honeycomb ceramics w...Micro-honeycomb ceramics were successfully fabricated through brush-coating with cloth fabric as pore-forming agent. The influence of pore-forming agent and slurry’s moisture content on the micro-honeycomb ceramics was investigated. The results indicated that micro-honeycomb ceramics made from pore-forming agent cloth fabric with fibre diameter of 100 μm and slurry with 45% （mass fraction） moisture content have the porosity of 65% （volume fraction）, bending strength of 24.3 MPa, pore size of about 100 μm, cell wall thickness of about 50 μm and porosity of 1131 pore/cm2. It was suggested that the pore size and the porosity could be adjusted using the pore-forming agent and moisture content of the slurry respectively.展开更多
基金supported by the National Natural Science Foundation of China (Grant Nos.21573109,21206069)the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD).
文摘Cobalt sulphides attract much attention as anode materials for Li-ion batteries(LIBs).However,its poor conductivity,low initial column efficiency and large volume changes during cycling have hindered its further development.Herein,novel interlaced CoS nanosheets were firstly prepared on Carbon Fiber Cloth(CFC)by two hydrothermal reactions followed with carbon coating via carbonizing dopamine(CoS NS@C/CFC).As a freestanding anode,the nanosheet structure of CoS not only accommodates the volume variation,but also provides a large interface area to proceed the charge transfer reaction.In addition,CFC works as both a three-dimensional skeleton and an active substance which can further improve the areal capacity of the resulting electrode.Furthermore,the coated carbon combined with the CFC work as a 3D conductive network to facilitate the electron conduction.The obtained CoS NS@C/CFC,and the contrast sample prepared with the same procedure but without carbon coating(CoS NS/CFC),are characterized with XRD,SEM,TEM,XPS and electrochemical measurements.The results show that the CoS NS@C/CFC possesses much improved electrochemical performance due to the synergistic effect of nanosheet CoS,the coated carbon and the CFC substrate,exhibiting high initial columbic efficiency(~87%),high areal capacity(2.5 at 0.15 mA cm−2),excellent rate performance(1.6 at 2.73 mA cm−2)and improved cycle stability(87.5%capacity retention after 300 cycles).This work may provide a new route to explore freestanding anodes with high areal specific capacity for LIBs.
文摘This study focuses on designing a solution to the perennial issue of clothing fit in Fashion Industry using tools offered by digital technology and statistical analysis, in particular, the data gathered on Asian women (Bangladeshi and Chinese). The study reveals that managing information can significantly enhance the capability of the industry to cater to the needs of its consumers and increase diversity. It centers on the effectiveness of turning dressmaking patterns into digital ones, thus transecting from traditional cutting and stitching to remote techniques. This entails the requirement to have correct self-measures and probable errors, which can arise in the process. Thus, with the help of regression analysis, the study identifies, which measurements are incorrect and influence the fit of the clothes, and, therefore, digital pattern creation is more accurate. Altogether, it can be observed how digitalization and statistical methods are crucial to transforming the way clothes are created to approach an ideal standard of measurements that fulfill every customer’s needs to make operational and efficient the clothing sector.
文摘This study aimed to comprehensively investigate the essential considerations in designing adaptive clothing for women with lower limb prostheses in Saudi Arabia. Employing a qualitative methodology, the research entailed semi-structured, in-depth interviews with women utilizing lower limb prostheses and prosthetic specialists. This approach was selected to unearth pivotal design prerequisites and comprehend the specific challenges these women encounter within the realm of clothing. The utilization of selective sampling facilitated the collection of intricate and valuable insights. A Functional, Expressive, and Aesthetic (FEA) User Needs model was utilized to scrutinize participant feedback. Functional requisites encompass ease of dressing and undressing, accessibility to the prosthetic limb, comfort, mobility with the prosthesis, and appropriate fit. Additionally, participants highlighted various expressive needs, including privacy preservation, modesty, camouflaging disability appearances, maintaining alignment with non-disabled women’s fashion, and considerations about the aesthetic aspects of garments.
基金support of the Fundamental Research Funds for the Central Universities(No.2022CDJQY-004)the Fund for Innovative Research Groups of Natural Science Foundation of Hebei Province(No.A2020202002).
文摘Recently,poly(ethylene oxide)(PEO)-based solid polymer electrolytes have been attracting great attention,and efforts are currently underway to develop PEO-based composite electrolytes for next generation high performance all-solid-state lithium metal batteries.In this article,a novel sandwich structured solid-state PEO composite electrolyte is developed for high performance all-solid-state lithium metal batteries.The PEO-based composite electrolyte is fabricated by hot-pressing PEO,LiTFSI and Ti_(3)C_(2)T_(x) MXene nanosheets into glass fiber cloth(GFC).The as-prepared GFC@PEO-MXene electrolyte shows high mechanical properties,good electrochemical stability,and high lithium-ion migration number,which indicates an obvious synergistic effect from the microscale GFC and the nanoscale MXene.Such as,the GFC@PEO-1 wt%MXene electrolyte shows a high tensile strength of 43.43 MPa and an impressive Young's modulus of 496 MPa,which are increased by 1205%and 6048%over those of PEO.Meanwhile,the ionic conductivity of GFC@PEO-1 wt%MXene at 60℃ reaches 5.01×10^(-2) S m^(-1),which is increased by around 200%compared with that of GFC@PEO electrolyte.In addition,the Li/Li symmetric battery based on GFC@PEO-1 wt%MXene electrolyte shows an excellent cycling stability over 800 h(0.3 mA cm^(-2),0.3 mAh cm^(-2)),which is obviously longer than that based on PEO and GFC@PEO electrolytes due to the better compatibility of GFC@PEO-1 wt%MXene electrolyte with Li anode.Furthermore,the solid-state Li/LiFePO_(4) battery with GFC@PEO-1 wt%MXene as electrolyte demonstrates a high capacity of 110.2–166.1 mAh g^(-1) in a wide temperature range of 25–60C,and an excellent capacity retention rate.The developed sandwich structured GFC@PEO-1 wt%MXene electrolyte with the excellent overall performance is promising for next generation high performance all-solid-state lithium metal batteries.
基金Project (2011WK4013) supported by the Basic Research Program of Hunan Provincial Science and Technology Department, ChinaProject (K1003031-11) supported by the Major Program for the Fundamental Research of Changsha Science and Technology Bureau, China
文摘Micro-honeycomb ceramics were successfully fabricated through brush-coating with cloth fabric as pore-forming agent. The influence of pore-forming agent and slurry’s moisture content on the micro-honeycomb ceramics was investigated. The results indicated that micro-honeycomb ceramics made from pore-forming agent cloth fabric with fibre diameter of 100 μm and slurry with 45% （mass fraction） moisture content have the porosity of 65% （volume fraction）, bending strength of 24.3 MPa, pore size of about 100 μm, cell wall thickness of about 50 μm and porosity of 1131 pore/cm2. It was suggested that the pore size and the porosity could be adjusted using the pore-forming agent and moisture content of the slurry respectively.
