STUDIES ON IPE OF POLYACRYLAMIDE INVERSE EMULSION AND MODIFIDE UREA-FORMALDEHYDE RESIN

The selective water plugging agent was prepared by heating the blends of the polyacry-lamide inverse latex, modified urea formaldehyde resin, crosslinking agent and catalysts.The results show that using different types of polymers and additives or changing in theirproportion of the blends, the gelling viscosity, starting point of gelling and other propertiesof the IPN can be controlled.

Short Communication—A Novel Sample Preparation Method That Enables Ultrathin Sectioning of Urea-Formaldehyde Resin for Imaging by Transmission Electron Microscopy

Urea-formaldehyde (UF) resin is widely used as an adhesive for the manufacture of a range of wood and fiber based products. Although the microstructure of this resin has been examined at high resolution by field-emission scanning electron microscopy and atomic force microscopy, transmission electron microscopy (TEM) has thus far not been used, perhaps because of difficulties in ultrathin sectioning this resin in cured (polymerized) state. In the technical note presented here, a novel sample preparation method is described which enabled us to examine the microstructural morphology of UF resin by transmission electron microscopy in ultrathin sections, revealing the presence of spherical particles within the resin. Our initial attempt to ultrathin section the resin directly was not successful as it was too brittle to trim blocks for sectioning. Then, we developed a sample preparation technique that involved impregnation ofPinus radiatawood tissues with the UF resin, and then embedding of resin impregnated wood tissues with Spurr’s low viscosity embedding medium, which has been widely employed in plant and wood ultrastructure work. The TEM images illustrated and the information on the microstructural morphology of the UF resin presented are based on this novel sample preparation approach.

New composite grouting materials:Modified urea-formaldehyde resin with cement

A new composite two component grout comprised of modified urea-formaldehyde resin and cement was formulated to take account of the advantages and disadvantages of both the cement grout and the chemical grout.The new grout is designed for water blocking by reinforcing as well as seepage control by bore grouting.The A component consists of a modified urea-formaldehyde resin A component,some cement,and some water.The B component is an alkaline coagulant.An orthogonal test of four factors at three levels showed that gel time increased with increased water content and with urea-formaldehyde resin content.Gel time decreased at increased levels of alkaline coagulant.The A component of this new composite grout is stable over time.A mixed cross-over test showed that as the volume ratio of A to B increases the gel time falls at first but then increases.The solid strength decreases with increasing levels of the B component.The solid strength increases over time and becomes stable by the 28th day after mixing.The viscosity increases with increasing levels of resin A component.The increase is exponential and may be fit to:l = 8.162e0.0286x.

Preparation of Environmentally Friendly Urea-Hexanediamine-Glyoxal(HUG)Resin Wood Adhesive

Using non-toxic,low-volatile glyoxal to completely replace formaldehyde for preparing urea-glyoxal(UG)resin adhesive is a hot research topic that could be of great interest for the wood industry.However,urea-glyoxal(UG)resins prepared by just using glyoxal instead of formaldehyde usually yields a lower degree of polymerization.This results in a poorer bonding performance and water resistance of UG resins.A good solution is to pre-react urea to preform polyurea molecules presenting already a certain degree of polymerization,and then to condense these with glyoxal to obtain a novel UG resin.Therefore,in this present work,the urea was reacted with hexamethylene diamine to form a polyurea named HU,and then this was used to react it with different amounts of glyoxal to synthesize hexamethylenediamine-urea-glyoxal(HUG)polycondensation resins,and to use this for bonding plywood.The results show that the glyoxal can well react with HU polyuria via addition and schiff base reaction,and also the HUG resin exhibits excellent bonding strength and water resistance.The shear strength of the plywood bonded with this HUG at 160°C hot press temperature as high as 1.93 MPa,2.16 MPa and 1.61 MPa,respectively,which meets the requirement of the China national standard GB/T 9846-2015(≥0.7 MPa),and can be a good choice as a wood adhesive for industrial application.

Evaluating two stages of silicone-containing arylene resin oxidation via experiment and molecular simulation

Silicon-containing aryl acetylene resin(PSA)is a new type of high-temperature resistant resin with excellent oxidation resistance,whereas antioxidant reaction mechanism of PSA resin under ultra-high temperatures still remains unclear.Herein,the oxidation behavior and mechanisms of PSA resin are systematically investigated combining kinetic analysis and Reax FF molecular dynamics(MD)simulations.Thermogravimetric analysis indicates that the oxidation process of PSA resin undergoes two main steps:oxidative mass gain and oxidative degradation.The distributed activation energy model(DAEM)is employed for describing oxidation processes and the best-fit one is obtained using genetic algorithms and differential evolution.DAEM model demonstrates that the oxidative weight gain stage is dominated by two virtual reactants and the oxidative degradation stage consists of three virtual reactants.Correspondingly,the observation of MD reaction pathways indicates that oxygen oxidation of unsaturated structures occurs in the initial stage,which results in the formation of PSA resin oxides.Furthermore,cracked pieces react with O_(2)to generate CO and other chemicals in the second step.The resin matrix's great antioxidation resilience is illustrated by the formation of SiO_(2).The analysis based on MD simulations exhibits an efficient computational proof with the experiments and DAEM methods.Based on the results,a two-stage reaction mechanism is proposed,which provides important theoretical support for the subsequent study of the oxidation behavior of silica-based resins.

Preparation and Swelling Kinetic Analysis of Poly (HPMC-co-AA-co-AM) Super Absorbent Resin

Super absorbent resin(SAR)is prepared by aqueous high temperature polymerization using hydroxypropyl methylcellulose(HPMC)as monomer backbone material,acrylic acid(AA)and acrylamide(AM)as the graft copolymer monomer,potassium persulfate(KPS)as the initiator to generate free radicals,and N,N`-methylenebisacrylamide(MBA)as cross-linking agent for cross-linking reaction.Simutaneously,the influence of individual factors on the water absorption is investigated,and these factors are mainly AA,AM,KPS,MBA,HPMC,and reaction temperature.The optimized conditions are obtained by the experiment repeating for several times.The water absorption multiplicity and salt absorption multiplicity under the conditions are 782.4 and 132.5 g/g,respectivity.Furthermore,the effects of different temperatures and salt concentrations on its water absorption,as well as the swelling kinetics of SAR are studied.It is indicated the water-absorbing swelling process is mainly caused by the difference in water osmotic pressure and Na+concentration inside and outside the cross-linked molecular structure of the resin,which is not only consistent with the quasi-secondary kinetic model,but also with the Fick diffusion model.

A functionalized activated carbon adsorbent prepared from waste amidoxime resin by modifying with H_(3)PO_(4) and ZnCl_(2) and its excellent Cr(Ⅵ)adsorption

With the application of resins in various fields, numerous waste resins that are difficult to treat have been produced. The industrial wastewater containing Cr(Ⅵ) has severely polluted soil and groundwater environments, thereby endangering human health. Therefore, in this paper, a novel functionalized mesoporous adsorbent PPR-Z was synthesized from waste amidoxime resin for adsorbing Cr(Ⅵ). The waste amidoxime resin was first modified with H3PO4 and ZnCl_(2), and subsequently, it was carbonized through slow thermal decomposition. The static adsorption of PPR-Z conforms to the pseudo-second-order kinetic model and Langmuir isotherm, indicating that the Cr(Ⅵ) adsorption by PPR-Z is mostly chemical adsorption and exhibits single-layer adsorption. The saturated adsorption capacity of the adsorbent for Cr(Ⅵ) could reach 255.86 mg/g. The adsorbent could effectively reduce Cr(Ⅵ) to Cr(Ⅲ) and decrease the toxicity of Cr(Ⅵ) during adsorption. PPR-Z exhibited Cr(Ⅵ) selectivity in electroplating wastewater. The main mechanisms involved in the Cr(Ⅵ) adsorption are the chemical reduction of Cr(Ⅵ) into Cr(Ⅲ) and electrostatic and coordination interactions. Preparation of PPR-Z not only solves the problem of waste resin treatment but also effectively controls Cr(Ⅵ) pollution and realizes the concept of “treating waste with waste”.

Optimization of tensile strength for new type acetone-urea-formaldehyde furan resin using uniform design

In this study,the 24 h tensile strength of new type acetone-urea-formaldehyde furan resin (nitrogen content 3%) was investigated by uniform design optimization.Four independent variables such as acetone:formaldehyde molar ratio (mol/mol),solution pH value,reaction temperature (℃) and reaction time (min) were considered in the experiments.U13(134) uniform design was employed and the equation of 24 h tensile strength model was obtained after 13 experimentations.The 24 h tensile strength was optimized by applying single factor experiments and stepwise non-linear regression analysis.Minitab (Minitab 15 trial version) and MATLAB (R2010a trial version) were used for data analysis.The t-value and p-value indicate that the major impact factors include the interaction effect of solution pH value and reaction temperature (X2X3),the linear terms of acetone:formaldehyde molar ratio (X1),reaction time (X4) followed by the square effects of acetone/formaldehyde molar ratio (X1X1).The optimized results were achieved with the acetone:formaldehyde molar ratio (mol/mol) at 3:1,solution pH value at 6.0,reaction temperature at 70℃,and reaction time at 140 min,respectively.This method can not only significantly reduce the number and cost of the tests,but also provide a good experimental design strategy for the development of furan resin.The investigation shows that the predicted results of 24 h tensile strength are consistent well with the experimental ones.

Micromechanical interlocking structure at the filler/resin interface for dental composites: a review

Dental resin composites(DRCs)are popular materials for repairing caries or dental defect,requiring excellent properties to cope with the complex oral environment.Filler/resin interface interaction has a significant impact on the physicochemical/biological properties and service life of DRCs.

Investigation of Color Change of Different Restoration Thickness, Background Color and Resin Cement Shade on CAD/CAM Glass Ceramic Materials

The aim of this study is to investigate the color change of different restoration thicknesses, backgrounds and resin cement colors on lithium disilicate and zirconium reinforced lithium silicate materials in vitro. In this study, IPS emax CAD (LT C14) and Celtra Duo (LT C14) are used as full ceramic materials, and Variolink Esthetic LC (warm, neutral) used as resin cement and Tokuyama Estelite Sigma Quick (A3, A2) is used as composite materials. A total of 160 samples in the form of 40 pieces of 5 × 5 0.4 mm thick 40 pieces of 5 × 5 0.6 mm thick square discs from each of the all-ceramic materials in block form were obtained using a water jet device (DWJ1525-FA;Dardi International Corporation, Nanjing, China). Glass ceramic samples produced in 2 different thicknesses were cemented on 2 different backgrounds with 2 different resin types of cement. Color measurements of the samples before and after cementation were performed on a grey background with spectrophotometer Vita EasyShade V (Vita Zahnfabrik, Bad Sackingen, Germany) and color parameters (L*, a*, b*, ΔE) were calculated according to the CIE Lab (Commission Internationale de L’Eclairage) system. Average values for each group (ΔE) were not affected by ceramic type, material thickness, background color, resin cement color, and the interaction of these four variables (p > 0.05). When the triple interactions between the groups were examined, there were no statistically significant differences (p > 0.05). In the evaluation of pairwise interactions between two groups (material type-material thickness, material type-background color, and thickness of material-background interactions) statistically significant differences (p Implications: The material type, thickness, background and cement color used did not cause any statistically significant color change in lithium disilicate and zirconium-reinforced lithium silicate glass ceramic materials (p > 0.05).

Resin composition: An indicator of oil maturity as revealed by fourier transform ion cyclotron resonance mass spectrometry

A pyrolysis experiment was carried out on a Dongying Depression kerogen sample to separate the resin from the oil. Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) with a positive-ion detector was used to detect the relative proportional changes in the compounds of the resin. During the whole pyrolysis experiment, the relative ratio of resin exceed 10% of the soluble component at each temperature point. Five compounds were detected from the resin: N1, N1O1, N1O_(2), O1, and O_(2). To research the changes in the proportions of the compounds during pyrolysis clearly, these five compounds were divided into three classes: N1, N1Ox, and Ox. The N1 class has the largest proportion in resin at the beginning of the pyrolysis, while Ox class has the least proportion. And the relationship between the number and the molecular mass of three classes compound was researched. With increasing maturity, the proportion of N1 and the N1Ox class decreased rapidly, while the Ox class increased slowly. Through researching these resin compounds, it was found that an inversion in the proportions of above three compounds appeared at the end of the oil window. At the same time, we found that the DBE and carbon number of resin compounds have changed obviously during the pyrolysis: the DBE increased, while the carbon number decreased significantly. And the details of the change of each compound have been researched. This research extends our knowledge of judging the maturity of crude oil during the pyrolysis through the characteristics of compounds in resin and provides the new index based on resin for the evaluation of thermal evolution stage and hydrocarbon generation capacity of source rocks.

Using optical coherence tomography images to evaluate fungal growth in reline resins

As changes in hard or soft oral tissues normally have a microbiological component,it is important to develop diagnostic techniques that support clinical evaluation,without destroying microbio-logical formation.The optical coherence tomography(OCT)represents an alternative to analyze tissues and microorganisms without the need for processing.This imaging technique could be defined as a fast,real-time,in situ,and non-destructive method.Thus,this study proposed the use of the OCT to visualize biofilm by Candida albicans in reline resins for removable prostheses.Three reline resins(Silagum-Comfort,Coe Comfort,and Soft-Confort),with distinct char-acteristics related to wa ter sorption and fungal inhibition were used.A total of 30 samples(10 for each resin group)were subjected to OCT scanning before and 96 h after inoculation with Candida albicans(URM 6547).The biofilm analysis was carried out through a 2D optical Callisto SD-OCT(930 nm)operated in the spectral domain.Then,the images were preprocessed using a3×3 Gaussian filter to remove the noise,and then Otsu binarization,allowing segmentation and pixel counting.The layer's biofilm formed was clearly defined and,indeed,its visualization is modified by water sorption of each material.Silagum-Comfort and Soft.Confort showed some similarities in the scattering of light between the clean and inoculated samples,in which,the latter samples presented higher values of light signal intensity.Coe-Comfort samples were the only ones that showed no di®erences between the clean or inoculated images.Therefore,the results of this study suggest that OCT is a viable technique to visualize the biolm in reline materials.Becausendings in the literature are still scarcely using the OCT technique to visualize biolm in reline resins,further studies are encouraged.It should not contain any references or displayed equations.

A novel high-efficient P/N/Si-containing APP-based flame retardant with a silane coupling agent in its molecular structure for epoxy resin

A flame retardant containing multiple antiflaming elements usually exhibits high-efficient flame retardancy. Here, a novel P/N/Si-containing ammonium polyphosphate derivative(APTES-APP) is synthesized from ammonium polyphosphate(APP) and silane coupling agent(3-aminopropyl)triethoxysilane(APTES)via cation exchange, which is quite different in the chemical structure from APTES-modified APP for retaining silicon hydroxyls. APTES-APP is highly efficient for the epoxy resin. 8%(mass) APTES-APP imparts excellent flame retardancy to the epoxy resin, with a V-0 rating at the UL-94 test(1.6 mm)and an LOI value of 26%(vol). The peak heat release rate and total smoke production of the flameretardant epoxy resin are decreased by 68.1% and 31.3%, respectively. The synergy of P/N/Si contributes to the well-expanded char residue with a strong and dense surface layer, which is a very good barrier against heat and mass transfer. Besides, there is no significant deterioration in the mechanical properties of flame-retardant epoxy resin thanks to silicon hydroxyls forming hydrogen bonds with epoxy molecules. Meanwhile, other molecules can be grafted onto APTES-APP via these silicon hydroxyls, if needed.Briefly, this work has developed a new strategy for amino silane as flame retardants. In conjunction with a low-cost and simple preparation method, APTES-APP has a promising prospect in the high-performance flame-retardant epoxy.

Liquid-phase esterification of methacrylic acid with methanol catalyzed by cation-exchange resin in a fixed bed reactor:Experimental and kinetic studies

The kinetic behavior of esterification between methacrylic acid and methanol catalyzed by NKC-9 resin was studied in a fixed bed reactor.The reaction was conducted in the temperature range of 323.15 to 368.15 K with the molar ratio of reactants from 0.8 to 1.4 under certain pressure.The measurement data were regression with the pseudo-homogeneous(P-H),Eley-Rideal(E-R),and Langmuir-Hinshelwood(L-H)heterogeneous kinetic models.Independent adsorption experiments were implemented to gain the adsorption equilibrium constants of four components.Among the above three models,the L-H model exhibited the best fitting results.The stability of NKC-9 was evaluated by long-term running with the yield of methyl methacrylate no decrease during 3000 h operation.The structure and physicochemical properties of the new and used catalyst were performed by several characterizations including thermogravimetric analysis(TG),scanning electron microscope(SEM),X-ray diffraction(XRD)and Fourier transform infrared spectroscopy(FT-IR)and so on.

Numerical Study on the Resin Transfer Molding Curing Process for Thick Composites Materials

The successful manufacture of thick composites is challenging since the highly exothermic nature of thermoset resins and limited temperature control make avoiding the onset of detrimental thermal gradients within the composite relatively difficult.This phenomenon is mainly caused by exothermic heat reactions.The so-called Michaud's model has been largely used in the literature to reduce the gap between experience and simulation with regard to the effective prediction of the temperature cycle in these processes.In this work,another solution is proposed to simulate the curing process for thick composites,namely preheating the resin to activate the curing reaction before resin injection into the mold.A good agreement between the experiment and the simulation is found.Moreover,in order to minimize the thermal gradient in the final composite,the thermophysical properties of the fiber and the torque(temperature,time)of the Plate have been varied leading to interesting results.

Curing Process of Phenol Formaldehyde Resin for Plywood under Vacuum Conditions

The study characterized the curing behaviors of phenol formaldehyde(PF)resin under different vacuum degrees and explored the properties of 9-ply plywood panels hot-pressed under both vacuum and atmospheric conditions.The changes in core temperature and moisture content of the plywood mats during hot pressing were investigated as well.It was found that the gel times and gel temperatures of PF resin decreased with the increase of vacuum degree using a self-made device.FTIR spectra indicated the degree of polycondensation of hydroxymethyl gradu-ally increased with the increase in temperature.It was also observed that a higher degree of vacuum led to a slower polycondensation reaction rate of PF resin.During different hot-pressing processes,the bonding strengths in the innermost and uppermost gluelines of the vacuum hot-pressed plywood panels were up to 30%–50%higher than their counterparts of conventional hot-pressed products.A less difference in the bonding strengths between these two gluelines was also observed for vacuum hot-pressed products.In addition,the core of vacuum hot-pressed plywood was found to have a greater heating rate and higher temperature at thefinal stage of hot pressing,which was beneficial to cure the PF resin.The results from this study indicate a promising potential of introducing a vacuum during hot pressing to improve the quality and productivity of plywood products and provide a basis for adopting vacuum to hot press wood composites.

MUF Resins Improved by Citric Acid as Adhesives for Wood Veneer Panels

This article presents the first applied results of using citric acid in combinations with a melamine-urea-formal-dehyde(MUF)resin for bonding wood veneers.The chemical reactions involved are shown based on a MALDI ToF analysis of the reaction of the MUF resin with citric acid.The preliminary results of the physical and mechanical properties of the LVL prepared are also presented.Veneers from Populus sp were used to manufacture 5-layer laminated veneer lumber(LVL)of small dimensions.Five combinations of the amount of citric acid,MUF spread rate and pressing parameters were tested.LVL bonded with 20%of citric acid+100 g/m^(2)of MUF,hot-pressed using a 3-step process with maximum 1.5 MPa of pressure yielded the board with better dimensional stability and mechanical properties.It could be concluded that citric acid in combination with MUF can be used for bonding wood veneer and the research should be continued to study further the parameters involved and to enhance the results.

A Boron-based Adhesion Aid for Efficient Bonding of Silicone Rubber and Epoxy Resin

We improved the adhesion between silicon based insulating materials and epoxy resin composites by adding the adhesion promoter cycloborosiloxane(BSi,cyclo-1,3,3,5,7,7-hexaphenyl-1,5-diboro-3,7-disiloxane).The experimental results show that the addition of BSi in the silicone rubber(SR)system significantly increases the tensile shear strength between BSi and epoxy resin(EP),reaching 309%of the original value.On this basis,the mechanism of BSi to enhance the adhesion effect was discussed.The electron deficient B in BSi attracted the electron rich N and O in EP to enhance the chemical interaction,combined with the interfacial migration behavior in the curing process,to improve the adhesion strength.This study provides the design and synthesis ideas of adhesive aids,and a reference for further exploring the interface mechanism of epoxy resin matrix composites.

External UHF Sensor for GIS PD Insulation Defect from Resin Hole

In view of the effective perception demand of PD(Partial Discharge)insulation defect of in-service GIS(Gas Insulated Switchgear),the external UHF(Ultra High Frequency,0.3−3 GHz)sensing technology for GIS PD insulation defect fromresin hole is studied in this paper.Firstly,rectangular waveguide theory is used to analyze the electromagnetic wave propagation characteristics from rectangular resin hole in GIS disc insulator.It is found that the energy of leaked electromagnetic wave mainly concentrates in the frequency band above 1 GHz.Then based on this frequency band characteristics,a cavity-backed bowtie sensor for GIS PD external detection is designed optimized by HFSS finite element software,in band of 1–3 GHz,its maximum VSWR is 7,the minimum is 1.1,the average is 2.9,and in band of 0.3–1 GHz,the maximum and minimum VSWR is 42.8 and 7,the average is 20.6.Finally,a sensor prototype is made,its sensitivity experiment is carried out on 220 kV GIS,experimental results show that the designed sensor can stably detect the PD electromagnetic wave signal leaked fromthe resin hole,and the signal energy in frequency band range is consistent with the theoretical analysis results.