Influence of heat-treatment on oxidation-resistance of phosphate-coating for C/C composite

Phosphate-coating was prepared for C/C composite using liquid-impregnation and different heat-treatment. The results show that the mass-loss rate of sample A with 1-2 ℃/min slow-cooling rate technology is 47%after oxidation at 700 ℃ for 20 h, while that of sample B with air-fast-cooling one is only 0.98%. SEM images reveal that the coating of sample A is full of micro-holes, micro-cracks and many piece-like crystal particles, while that of sample B is integrated and compacted in glassy state with a few of micro-cracks. The coating of sample A is almost exhausted only in 8 h oxidized-test at 700 ℃, while that of sample B remains integrated after 8 h test at 700 ℃ and becomes loose due to much small pores generated after 20 h test at 700 ℃.

Effect of Heat-Treatment Process on Properties of Rare Earth Mg-Based System Hydrogen Storage Alloys with AB_3-Type

The effect of heat-treatment process on the properties of Mm0.8Mg0.2(NiCoAlMn)3.5 hydrogen storage alloy was discussed . The electrochemical properties such as cycling stability, activation property, and the plateau voltage of the alloy which was heat-treated in various temperatures and times had different changes during the cycle process, the optimum heat-treatment conditions of this alloy were determined by this work.

Effects of Heat-treatment on Crystallization and Wear Property of Plasma Sprayed Fe-based Amorphous Coatings

The Fe-based amorphous coatings were produced by air plasma spraying. The as-sprayed coatings were heat-treated at the temperature of 573, 873, and 1 023 K, respectively. The crystallization and wear behavior of the heat-treated amorphous coatings were investigated. It was found that the amorphous- nanocrystalline transformation appeared when the as-sprayed coatings were treated at 853 K. The crystallization process had completed and a coating with microcrystallines was formed when the treatment temperature reached 1 023 K. The resultant amorphous and nanocrystalline composite coatings exhibited superior wear resistance compared to crystalline coating. It is attributed to fine grain strengthening of formed nanocrystallines.

Effects of Steam Heat-Treatment on Properties of Pinus massoniana Wood and Its Bonding Performance

Pinus massoniana wood was modified by steam heat-treatment at 160℃,180℃,200℃ and 220℃ respectively and effects of the changes of density,pH,surface wettability and apparent morphology of Pinus massoniana heat-treated wood on its bonding performance were studied in this paper.The results showed that Pinus massoniana wood underwent a series of physical and chemical changes during heat-treatment as the the following:(1)The degradation of hemicellulose and cellulose with low degree of polymerization,degradation and migration of the extract resulting in the decline of density and pH of heat-treated Pinus massoniana wood.(2)Brittle fracture occured on the cell wall surface,and the pit collapse,shrink and deformation,resulting in the formation of roughness and porosity on the wood surface.(3)The surface energy decreased with the improvement of temperature,the surface wettability of Pinus massoniana wood treated at 160℃–180℃ was good,while that at 200℃–220℃ showed hydrophobicity.(4)Changes of density,pH,surface roughness and porosity,and wettability resulted in a reduction in the bonding strength and reliability of heat-treated Pinus massoniana wood with MUF resin adhesive.(5)When the temperature was at 160℃–180℃,the better wettability of heat-treated Pinus massoniana wood could guarantee the better bonding performance.

Effect of Heat-treatment Temperature on HA-coated Titanium Materials

Homogeneous HA coating materials were prepared on porous titanium by the low-temperature combustion synthesis. It was found that the mechanical properties of the specimen depend on the coating process and the heat treatment, and the bending strength would be reduced during the coating process but could be improved by heat treatment. The effects of the temperature during heat- treatment on the phase composition and microstructure of the as-prepared coating, and the bending strength of the specimen were investigated by XRD and SEM. The experimental results show that in the coating process, slight oxidation of the substrate may give rise to a drop in bending strength ; however, it could be increased by the reaction of HA and TiO2 , and the sintering of the coating during heat treatment. The HA particles in the coating, with very fine sized particles. were pretty active and would decompose at 800℃.

EFFECT OF HEAT-TREATMENT ON THE MECHANICAL PROPERTIES OF AIN/SICw(Y_2O_3+SiO_2)COMPOSITE

In the paper, the effect of heat-treatment on the strength and toughness of AIN-SiC whisker composites with Y2O3 + SiO2 additives have been studied. When the Sample confining 10wt% Y2O3+SiO2(.Y2O3/SiO2^l/0. 66) -was treated at 1330癈 in air for 140 hours ithe flexural strength of composites ivas raised from 481 MPa to 784 MPa the toughness ruas also enhanced slightly. The phase composi-tion infrastructure and grain boundary phase structure have been char-acterized by combining XDR, SEM, TEM/EDXA and HREM tech-niques, reinforcenent and toughening mechanism of the composites re-sults from the crystallization of glass phase in the grain boundary at the high temperature oxidizing atmosphere to form the crossing struc-ture of 2H?sialon fibrous phase and SiC whisker

STUDY ON HEAT-TREATMENT OF AIN/SiC_w COMPOSITES AND EFFECTS ON MICROSTRUCTURE AND PROPERTIES

AlN-SiC whisker composites with Y2O3 and SiO2 additives were heat-treated at 1300 ℃ in air. The phase composition and microstrurture were analyzed using XRD, SEM and HREM techniques to study the effect of heat-treatment on the microstructure and properties of the composites. The results reveal that the mechanical properties and high temperature oxidation resistance of the composite of ivhich additives composition approaches the eutectic point of Y2O3-SiO2 can be improved through the heat-treatment. Glass phase in the grain boundary is observed to react with the surface composition of AlN forming fibrous 2Hδ Sialon, resulting a crossing structure produced by fibrous 2Hδ Sialon and SiC whiskers.

Effect of Seed Heat-Treatment on the Oxidative Stability of Canola Oil Body Emulsions

Enhancement of oxidative stability of canola oil extracted from seed subjected to prior heat-treatment has been attributed to heat-induced generation of antioxidants from phenolic precursors occurring in canola seed. Dispersion of aqueous extracts of intact seed oil bodies (OBs) in water is a novel and interesting way of producing natural and oxidatively stable food emulsions with minimal use of synthetic antioxidants and emulsifiers. As there is growing interest in natural food emulsions containing unsaturated oils, we investigated whether the oxidative stability of canola OB emulsions could be further improved by subjecting canola seed to heat-treatment prior to oil body extraction. Oil-in-water (5%, w/w) emulsions of OBs extracted from canola seed before and after heat-treatment were considerably more resistant to oxidation than emulsions prepared from refined canola oil and Tween? 40 emulsifier. However, only small amounts (0.9% - 4.5% by weight) of the phenolic compounds present in canola seed were transferred to the OBs after aqueous extraction, and consequently there was no discernible effect on oxidative stability as a result of prior heat-treatment of the seed. Thus, in contrast to oil, there is no oxidative stability benefit to be gained by subjecting canola seed to heat-treatment prior to extraction of OBs.

Synthesis and microwave absorption performance of heat-treated RF/SiO_(2)aerogels

The well-designed composite with satisfactory electromagnetic microwave absorption at high temperatures remains a serious challenge.Herein,we fabricated a resorcinol-formaldehyde/silica dioxide composite aerogel(RF/SiO_(2))with a three-dimensional network structure using sol-gel,atmospheric pressure drying technique as well as heat-treated processes to achieve enhanced microwave absorption capabilities in the low frequency range.The pristine RF/SiO_(2)aerogel presented a typical micropores structure with a surface area,porous volume,and density of 146.82 m^(2)/g,62.40%,and 0.28 cm^(3)/g,respectively.Remarkably,the RF/SiO_(2)aerogel showed an effective absorption bandwidth of 3.56 GHz and a minimum reflection loss value of-46.10 d B at 2.25 mm after being heat-treated at 1500°C,while the maximum effective absorption bandwidth was 3.60 GHz at 2.30 mm.The intricate three-dimensional networks possessed remarkable impedance matching,multiple attenuation mechanisms,interfacial polarization,and dielectric loss,which were attributed to the exceptional ability to absorb electromagnetic microwaves.It offered a fresh approach to creating adaptable and effective microwave absorption materials in military defense.

Heat-treated wood and its development in Europe

Efficient use of timber is a vital concern problem, especially in these regions where the forestry coverage ratio is decreasing. Studies on physical modification of wood have been taken more attention due to the increasing attentions on environmental protection. Thermal modification is emphasized and developed quickly in developing countries, especially in European countries. A large number of researches have been conducted and some industrial production plants have been built. This paper reviewed the history of heat treatment, exemplifies the industrial developments in several European countries, summarized the basic principle of heat treatment and describes the environmental characteristics. The properties of heat-treated wood and its usage are also summed up.

Effect of Ca addition on the microstructure and mechanical properties of heat-treated Mg-6.0Zn-1.2Y-0.7Zr alloy

In this study,the effects of Ca addition on the microstructure,thermal properties,and mechanical properties of a Mg-6.0Zn-1.2Y-0.7Zr(ZWK611)alloy at room temperature and 150℃ were investigated.With an increase in the Ca content,the ignition resistance of the ZWK611 alloy improved and the grains became finer.The as-cast ZWK611 alloy consisted mainly of the dendriticα-Mg matrix and I-phase(Mg_(3)Zn_(6)Y)at the grain boundaries.On the other hand,theτ-(Ca_(2)Mg_(6)Zn_(3))and I-phases were formed in the Ca-added ZWK611 alloy.The fraction of theτ-phase increased with an increase in the Ca content.After the solid-solution treatment,these phases remained partially at the grain boundaries of the Ca-added ZWK611 alloys and an additional W-phase(Mg_(3)Zn_(3)Y)was observed.The phases remaining at the grain boundaries restricted the grain growth through the grain boundary pinning effect.The aging treatment resulted in the formation of MgZn'precipitates in theα-Mg matrix of the alloys.These precipitates were more uniformly distributed in the Ca-added alloys than in the alloys without Ca.Thus,the heat treatment-induced precipitation improved the tensile and creep properties of the T6-treated alloys.The T6-treated ZWK611+0.7Ca alloy exhibited the best mechanical properties at room temperature and 150℃ among all the tested alloys.

Microstructure and cutting performance of Ti(C, N)-based cermets heat-treated in nitrogen

Ti（C, N）-based cermets were treated using hot isostatic pressing （HIP） at 1423 K in nitrogen. The microstructures compared with the as-sintered cermets were investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray analysis, and electron microprobe analysis. It was found that high nitrogen activity in the surface zone resulted in the formation of gradient structure. Approximately 20-1am-deep, nitrogen-rich and titanium-rich hard surface zone was introduced by the heat treatment. The nitrogen activity was the driving force that caused the transportation of the atoms through the binder, titanium towards the surface, and tungsten and molybdenum inwards. In the surface zone, the particle size became fine, the inner rim disappeared, and the volume fraction of the outer rim and the binder phase considerably reduced. Small grains of TiN, WC, Mo2C, and nitrogen-rich carbonitlide phases formed in the surface zone during the heat treatment, improving the tlibological property of the heat-treated cermet.

Study on Weathering Behavior of Jack Pine Heat-Treated under Different Conditions

It is of considerable importance to investigate the influence of weathering on the degradation processes of heat-treated wood. Kiln-dried （untreated）jack pine （Pinus banksiana） and jack pine heat-treated at three different temperatures （190 ℃, 200 ℃, and 210 ℃） were exposed to artificial weathering for different periods in order to understand the degradation processes due to weathering. Before and after exposure, their color and wettability by water were determined. Structural changes and chemical modifications at exposed surfaces were also investigated using SEM （scanning electron spectroscopy）, FTIR （Fourier transforms infrared spectroscopy）, and XPS （X-ray photoelectron spectroscopy）. The results revealed that the photo-degradation of lignin and the presence of extractives play important roles in color change and wetting behavior of heat-treated wood surfaces during weathering. The structural changes also influence the wettability. The effects of weathering for woods heat-treated under different conditions were similar, but different from those for untreated wood.

Effectiveness of Bark Extracts and CeO2 Nano Particles as Coating Additives for the Protection of Heat-Treated Jack Pine

High temperature heat-treatment of wood, which is value-added green product, is one of the altematives to chemical treatment. It has better dimensional stability, thermal insulating properties and biological resistance compared to kiln dried wood. It also has dark brown color which is very important for decorative purposes. Unfortunately, this color changes during weathering. Developing a transparent and non-toxic coating for the protection of heat-treated wood against discoloration without changing its natural appearance is the main objective of this study. For this purpose, waterborne acrylic polyurethane base was chosen because of its durability against weathering and non-toxic nature. Natural antioxidants which are extracted from barks and CeO2 nano particles （alone or together with lignin stabilizer） were used as additives to develop different coatings. The protective characteristics of these coatings were compared with highly pigmented and toxic industrial coating under accelerated weathering conditions. The results showed that acrylic polyurethane coatings protected wood better compared to commercially available coating tested in this study. The chemical modifications during accelerated weathering of coated and heat-treated wood surfaces were monitored by X-ray photoelectron spectroscopy analysis. The morphological changes took place during weathering were studied by fluorescence microscope analysis.

25岁以下未育女性负压吸宫术后即时放置两种宫内节育器的随机对照观察

目的:观察25岁以下未育女性负压吸宫术后即时分别放置吉妮致美或含药含铜宫型宫内节育器(IUD)的可行性和效果。方法:将自愿要求人工流产的≤25岁未育早孕女性作为观察对象,随机表法分组,分别放置吉妮致美IUD组(195例)和含药含铜宫型IUD组(简称宫药铜组)(196例)。于负压吸宫术后即时放置IUD,随访6个月,观察IUD的使用效果。结果:两组IUD的顺利放置率≥99%。采用生命表法对IUD的终止情况进行分析。两组均无妊娠发生,宫药铜组无脱落相关终止,吉妮致美组脱落相关终止率为2.09/100妇女年,高于宫药铜组(P<0.05)。吉妮致美组因症取出率为0.53/100妇女年,宫药铜组为1.60/100妇女年,但差异无统计学意义(P>0.05)。吉妮致美组和宫药铜组与IUD使用相关的终止率分别为1.60/100妇女年和2.60/100妇女年,两组间差异无统计学意义(P>0.05)。放置IUD后1、3、6个月随访时,吉妮致美组和宫药铜组IUD副作用的主诉率分别为17.3%、13.4%、6.7%和28.7%、29.5%、21.5%,吉妮致美组低于宫药铜组,差异有统计学意义(P<0.01、P<0.001、P<0.001)。结论:年轻未育女性负压吸宫术后即时放置吉妮致美或宫药铜IUD均安全、可行、避孕效果可靠,与宫药铜IUD相比吉妮致美IUD使用后不适主诉更少,需关注放置技术以减少脱落。

洋葱状富勒烯的提纯研究

以石墨粉为碳源,Al为催化剂,采用真空热处理法制备了平均粒径为15～35nm的洋葱状富勒烯(OLFs).并用CS2分离和空气氧化法对得到的OLFs初产品进行了提纯处理.高分辨透射电镜(HRTEM)、X射线衍射(XRD)、热重分析(TGA)对提纯前后样品的分析表明,CS2分离处理可有效去除初产品中裸露的金属催化剂微粒,然后在空气中610℃焙烧200min,可基本去除无定型碳,并大量去除了石墨状碎片等碳杂质,OLFs的纯度在50%(体积分数)以上.

骨科负压封闭引流技术的临床应用

目的观察负压封闭引流技术对临床顽固感染的治疗效果。方法32例软组织、骨与关节感染的患者,其他方法治疗仍经久不愈,平均138 d;结合负压封闭引流技术,治疗23 d,从而形成自身对照。结果32例患者随访至少1年,除1例复发外均治愈。结论负压封闭引流是目前最为有效的外科引流手段,是一种全方位的引流,应用得当,能有效地治疗骨科感染。

立方氮化硼粉末的热处理研究

将立方氮化硼在氮气或真空中以不同温度和保温时间进行热处理,用XRD和SEM对相组分和形貌进行了分析。结果表明:立方氮化硼在1 350℃氮气氛中经过10 h处理,可以变为六方氮化硼;在1 550℃真空中(1—5 Pa)经过5 h处理,可以变为六方氮化硼,但其粒径和形貌均不发生变化。

低温真空干燥焙制荔枝干、龙眼干的研究

研究了荔枝、龙眼真空干燥时间、真空度、温度等的影响,提出适宜的工艺参数,研制了高质量的荔枝干、龙眼干。

Mammotome微创旋切术加置管冲洗引流治疗慢性乳腺炎22例

目的:探讨应用Mammotome微创旋切术加置管冲洗引流治疗慢性乳腺炎的优化方法和操作技巧。方法:超声引导下应用Mammotome微创真空辅助活检系统切除肿块型与脓肿型慢性乳腺炎的局部病灶,辅以残腔冲洗及置管引流。与同期传统方法治疗者对比,观察其治疗上的优势。结果:Mammotome组22例一次治愈率为95.5%(21/22),仅1例于术后5d内冲洗换药持续可见脓性分泌物,为术后引流不畅所致,扩大引流口后22d痊愈;平均治愈时间(9.36±2.22)d;复发率为4.5%(1/22)。对比传统组25例一次治愈率68.0%(17/25,χ2=4.062,P<0.05)、平均治愈时间[(30.28±11.51)d,t′=-8.899,P<0.01]及局部复发率32.0%(8/25,χ2=4.062,P<0.05),差异均具有明显统计学意义。结论:Mammotome微创旋切术可在超声引导下将慢性乳腺炎局部病灶行大范围或完全切除,辅以置管冲洗引流,可明显缩短慢性乳腺炎的治愈时间以及改善治疗效果。