The thermal conductivity of epoxy resin can be increased by a factor of eight to ten by loading with highly conductive particles. However, higher loadings increase the viscosity of the resin and hamper its use for liq...The thermal conductivity of epoxy resin can be increased by a factor of eight to ten by loading with highly conductive particles. However, higher loadings increase the viscosity of the resin and hamper its use for liquid composite molding processes. Thus, the enhancement of the out-of-plane thermal conductivity of carbon composites manufactured by VARTM and accomplished by matrix filling is limited to about 250%. In order to derive higher increases in out-of-plane thermal conductivity, additional measures have to be taken. These consist of introducing thermally conductive fibers in out-of-plane direction of the preform using a 3D-weaving process. Measured out-of-plane thermal conductivities of 3D-woven fabric composites are significantly increased compared to a typical laminated composite. It has been shown that if introducing highly conductive z-fibers, the use of a particle filled resin is not necessary and furthermore should be avoided due to the manufacturing problems mentioned above. An existing analytical model was altered to predict the effective thermal conductivity as a function of the composite material properties such as the thermal conductivities and volume contents of fibers in in-plane and out-of-plane directions, the thermal conductivity of the loaded resin, the grid-density of the out- of-plane fibers, and material properties of the contacting material. The predicted results are compared with measured data of manufactured samples.展开更多
This work deals with the investigation of the synergistic effect of bagasse ash with sisal-banana-kenaf-flax fibers reinforced epoxy composite for their flexural behavior.The composites with three combinations of hybr...This work deals with the investigation of the synergistic effect of bagasse ash with sisal-banana-kenaf-flax fibers reinforced epoxy composite for their flexural behavior.The composites with three combinations of hybrid fibers viz.sisal/kenaf(HSK),banana/kenaf(HBK),and banana/flax(HBF)with bagasse ash(BGA)as filler material are fabricated using vacuum bag assisted resin transfer molding.Experiments were conducted based on L27 orthogonal array to understand the influence of control factor viz.fiber volume,alkali concentration&BGA over output response.A'-ray micro computed tomography analysis was conducted over the developed sample to infer the uniform dispersion of fiber and filler material.The experimental results reveal that the addition of fiber up to 30 vol%depicts better strength and further addition results in a negative impact.Increasing in order of BGA decreases the flexural strength of the developed composites.展开更多
文摘The thermal conductivity of epoxy resin can be increased by a factor of eight to ten by loading with highly conductive particles. However, higher loadings increase the viscosity of the resin and hamper its use for liquid composite molding processes. Thus, the enhancement of the out-of-plane thermal conductivity of carbon composites manufactured by VARTM and accomplished by matrix filling is limited to about 250%. In order to derive higher increases in out-of-plane thermal conductivity, additional measures have to be taken. These consist of introducing thermally conductive fibers in out-of-plane direction of the preform using a 3D-weaving process. Measured out-of-plane thermal conductivities of 3D-woven fabric composites are significantly increased compared to a typical laminated composite. It has been shown that if introducing highly conductive z-fibers, the use of a particle filled resin is not necessary and furthermore should be avoided due to the manufacturing problems mentioned above. An existing analytical model was altered to predict the effective thermal conductivity as a function of the composite material properties such as the thermal conductivities and volume contents of fibers in in-plane and out-of-plane directions, the thermal conductivity of the loaded resin, the grid-density of the out- of-plane fibers, and material properties of the contacting material. The predicted results are compared with measured data of manufactured samples.
文摘This work deals with the investigation of the synergistic effect of bagasse ash with sisal-banana-kenaf-flax fibers reinforced epoxy composite for their flexural behavior.The composites with three combinations of hybrid fibers viz.sisal/kenaf(HSK),banana/kenaf(HBK),and banana/flax(HBF)with bagasse ash(BGA)as filler material are fabricated using vacuum bag assisted resin transfer molding.Experiments were conducted based on L27 orthogonal array to understand the influence of control factor viz.fiber volume,alkali concentration&BGA over output response.A'-ray micro computed tomography analysis was conducted over the developed sample to infer the uniform dispersion of fiber and filler material.The experimental results reveal that the addition of fiber up to 30 vol%depicts better strength and further addition results in a negative impact.Increasing in order of BGA decreases the flexural strength of the developed composites.
