A remote sensing system of vehicle emissions based on tunable diode laser technology

As being an effective real-time method of monitoring vehicle emissions on-road, a remote sensing system based on the tunable diode laser （TDL） technology was presented, and the key technologies were discussed. A field test in Guangzhou（Guangdong, China） was performed and was found that the factors, such as slope, instantaneous speed and acceleration, had significant influence on the detectable rate of the system. Based on the results, the proposal choice of testing site was presented.

Temporal-spatial dynamic characteristics of vehicle emissions on intercity roads in Guangdong Province based on vehicle identity detection data

Estimating intercity vehicle emissions precisely would benefit collaborative control in multiple cities.Considering the variability of emissions caused by vehicles,roads,and traffic,the 24-hour change characteristics of air pollutants(CO,HC,NO_(X),PM_(2.5))on the intercity road network of Guangdong Province by vehicle categories and road links were revealed based on vehicle identity detection data in real-life traffic for each hour in July 2018.The results showed that the spatial diversity of emissions caused by the unbalanced economywas obvious.The vehicle emissions in the Pearl River Delta region(PRD)with a higher economic level were approximately 1–2 times those in the non-Pearl RiverDelta region(non-PRD).Provincial roads with high loads became potential sources of high emissions.Therefore,emission control policies must emphasize the PRD and key roads by travel guidance to achieve greater reduction.Gasoline passenger cars with a large proportion of traffic dominated morning and evening peaks in the 24-hour period and were the dominant contributors to CO and HC emissions,contributing more than 50%in the daytime(7:00–23:00)and higher than 26%at night(0:00–6:00).Diesel trucks made up 10%of traffic,but were the dominant player at night,contributed 50%–90%to NO_(X) and PM_(2.5) emissions,with amarked 24-hour change rule of more than 80%at night(23:00–5:00)and less than 60%during daytime.Therefore,targeted control measures by time-section should be set up on collaborative control.These findings provide time-varying decision support for variable vehicle emission control on a large scale.

Modeling and predicting low-speed vehicle emissions as a function of driving kinematics

An instantaneous emission model was developed to model and predict the real driving emissions of the low-speed vehicles. The emission database used in the model was measured by using portable emission measurement system （PEMS） under actual traffic conditions in the rural area, and the characteristics of the emission data were determined in relation to the driving kinematics （speed and acceleration） of the low-speed vehicle. The input of the emission model is driving cycle, and the model requires instantaneous vehicle speed and acceleration levels as input variables and uses them to interpolate the pollutant emission rate maps to calculate the transient pollutant emission rates, which will be accumulated to calculate the total emissions released during the whole driving cycle. And the vehicle fuel consumption was determined through the carbon balance method. The model predicted the emissions and fuel consumption of an in-use low-speed vehicle type model, which agreed well with the measured data.

Comparison of the Mutagenicity of Exhaust Emissions From Motor Vehicles Using Leaded and Unleaded Gasoline as Fuel

While Unleaded gasoline has the advantage of eliminating lead from automobile exhaust, its potential to reduce the exhaust gas and particles, merits further examination. In the present studies,the concentrations of hydrocarbons (HC) and earbon monoxides (CO) in emissions were analyzed on Santana engine Dynamometer under a standard test cycle, and total exhaust particles were collected from engines using leaded and unleaded gasoline. It was found that unleaded gasoline reduced the emissions of CO and HC, and decreased the quantity of vehicle exhaust particulate matters by 60%.With the unlead gasoline, only 23 kinds of organic substances, adsorbed in the particles, were identified by gas chromatography/mass spectrometer (GC/MS) while 32 components were detected using the leaded gasoline. The results of in vitro Salmonella/ microsomal test and micronucleus induction assay in CHL cells indicated that both types of gasoline increased the number of histidine-independent colonies and the frequencies of micronucleus induction; no significant differellce was found in their mutagenicity.

Artificial neural network model for identifying taxi gross emitter from remote sensing data of vehicle emission

Vehicle emission has been the major source of air pollution in urban areas in the past two decades. This article proposes an artificial neural network model for identifying the taxi gross emitters based on the remote sensing data. After carrying out the field test in Guangzhou and analyzing various factors from the emission data, the artificial neural network modeling was proved to be an advisable method of identifying the gross emitters. On the basis of the principal component analysis and the selection of algorithm and architecture, the Back-Propagation neural network model with 8-17-1 architecture was established as the optimal approach for this purpose. It gave a percentage of hits of 93%. Our previous research result and the result from aggression analysis were compared, and they provided respectively the percentage of hits of 81.63% and 75%. This comparison demonstrates the potentiality and validity of the proposed method in the identification of taxi gross emitters.

Real-world vehicle emission factors in Chinese metropolis city—Beijing

The dynamometer tests with different driving cycles and the real-world tests are presented. Results indicated the pollutants emission factors and fuel consumption factor with ECE15+EUDC driving cycle usually take the lowest value and with real world driving cycle occur the highest value, and different driving cycles will lead to significantly different vehicle emission factors with the same vehicle. Relative to the ECE15+EUDC driving cycle, the increasing rate of pollutant emission factors of CO, NOx and HC are -0.42—2.99, -0.32 —0.81 and -0.11—11 with FTP75 testing, 0.11—1.29, -0.77—0.64 and 0.47—10.50 with Beijing 1997 testing and 0.25—1.83, 0.09—0.75 and -0.58—1.50 with real world testing. Compared to the carburetor vehicles, the retrofit and MPI+TWC vehicles' pollution emission factors decrease with different degree. The retrofit vehicle(Santana) will reduce 4.44%—58.44% CO, -4.95%—36.79% NOx, -32.32%—33.89% HC, and -9.39%—14.29% fuel consumption, and especially that the MPI+TWC vehicle will decrease CO by 82.48%—91.76%, NOx by 44.87%—92.79%, HC by 90.00%—93.89% and fuel consumption by 5.44%—10.55%. Vehicles can cause pollution at a very high rate when operated in high power modes; however, they may not often operate in these high power modes. In analyzing vehicle emissions, it describes the fraction of time that vehicles operate in various power modes. In Beijing, vehicles spend 90% of their operation in low power modes or decelerating.

Emission Patterns under Alternative Congestion and Motor Vehicle Pollution Mitigation Policies in Shanghai

As a megacity with thriving economy, Shanghai is experiencing rapid motorisation and confronted with traffic congestion problems despite its low car ownership. It is of value to look into the policies on emission control of motor vehicle and congestion reduction in such a city to explore how to reconcile mobility enhancement with the environment. Results of a dynamic simulation displayed time paths of emissions from motor vehicles in Shanghai over the period from 2000 to 2020. The simulation results showed that early policies on emission control of motor vehicle could bring about far-reaching effects on emission reduc- tion, and take advantage of available low-polluting technologies and technical innovation over time. Travel demand management would play an important role in curbing congestion and reducing motor vehicle pollution by calming down car ownership rise and deterring inefficient trips as well as reducing fuel waste caused by congestion.

COMPOSITIVE EMISSION CONTROL SYSTEM OF GASOLINE VEHICLE

The working principle of a kind of compositive emission control system is inquired into, which includes exhaust heater, secondary air supplement, exhaust gas recirculation （EGR）, thermal reactor and catalytic converter, etc. The purification effect of CO, HC and NOx emission of the gasoline spark ignite （S.I.） engine is studied. The entire vehicle driving cycle tests based on the national emission standard and a series of the gasoline engine-testing bench tests including full load characteristic experiment, load characteristic experiment and idle speed experiment are done. The results show that the system has a very good emission control effect to CO, HC and NOx of gasoline engine. The construction of the system is very simple and can be mounted on the exhaust pipe conveniently without any alteration of the vehicle-use gasoline engine.

Investigation of performance and emission characteristics of waste cooking oil as biodiesel in a diesel engine

Biodiesel is one of the most popular prospective alternative fuels and can be obtained from a variety of sources. Waste frying oil is one such source along with the various raw vegetable oils. However, some specific technical treatments are required to improve certain fuel properties such as viscosity and calorific value of the biodiesel being obtained from waste cooking oil methyl ester （WCOME）. Various treatments are applied depending on the source and therefore the composition of the cooking oil. This research investigated the performance of WCOME as an alternative biofuel in a four-stroke direct injection diesel engine. An 8-mode test was undertaken with diesel fuel and five WCOME blends. The best compromise blend in terms of performance and emissions was identified. Results showed that energy utilization factors of the blends were similar within the range of the operational parameters （speed, load and WCOME content）. Increasing biodiesel content produced slightly more smoke and NOx for a great majority of test points, while the CO and THC emissions were lower.

Nitrogen Dioxide and Ozone Pollution in the Chicago Metropolitan Area

Ground-level ozone is a harmful air pollutant associated with several health issues. Ozone concentrations have exceeded the National Ambient Air Quality Standards (NAAQS) in the Chicago metropolitan area on hot summer days for many years because of nitrogen oxide and volatile organic compound emissions. Annual fourth highest 8-hour ozone concentrations have been between 0.070 and 0.084 ppm at several monitoring sites in Cook county, during the 2016-2018 time period. The continuous measurement of nitrogen dioxide (NO2) and ozone (O3) was conducted in several communities in Chicago in 2017. The air pollution impacts the health of all who live in the area. The data were used to analyze correlations between the O3 distribution and its association with ambient concentrations of NO2 from transportation emissions. Higher concentrations in NO2 and O3 occurred in succession in the daytime. The diurnal variation of O3 concentration was analyzed. The daily cycle of NO2 concentration reaches a maximum in the late morning and has smaller nighttime concentrations. The daily cycle of ozone concentration reaches the maximum in the afternoon and also becomes smaller for nighttime concentrations. In addition, relationships were found between O3 and NO2. Monthly variations of ozone and NO2 are presented. Some options to reduce ozone pollution are presented.

Variability in the Levels of BTEX at a Pollution Hotspot in New Delhi, India

It is a matter of concern that despite taking measures to control aromatic content in gasoline in India, the levels of volatile organic compounds are rising again in many of the Indian cities. The transport sector has been one of the major sectors which are re-sponsible for worsening the air quality of Delhi city. While thousands of toxic com-pounds are emitted from automobiles, industries, gasoline stations as well as service stations, however, volatile organic compounds are important due to their significant contribution to ozone formation, cancer, and non-cancer health risks. In this study, roadside levels of benzene, toluene, ethylbenzene and xylenes (BTEX) were investi-gated at the one of the major arterial road of Delhi city. Air samples were collected by activated coconut shell charcoal adsorbent tubes. The BTEX concentrations were de-termined by gas chromatography-flame ionization detector (GC-FID) technique. The mean concentrations of benzene, toluene, ethylbenzene and xylenes were, respectively, 60.22, 162.68, 49.42 and 25.25 μg/m3. The relative concentration distribution pattern and mutual correlation analysis indicated that in BTEX had sources other than vehicle emission at the study site. The samples collected, showed that BTEX had significantly higher concentrations in winter than those in spring and summer.

Impact of gasoline engine deposits on light duty vehicle emissions： in-use case study in Beijing, China

Tailpipe emissions from light-duty gasoline vehicles usually deteriorate over time. The accumulation of engine deposits due to inadequate gasoline detergency is considered to be one of the major causes of such emission deterioration. Six in-use light-duty gasoline vehicles in Beijing were tested to investigate the impact of engine deposits on emissions of hydrocarbons （HC）, carbon monoxide （CO） and nitrogen oxides （NOx）. Emissions under cold start and hot running test conditions from the six light duty vehicles were measured before and after engine deposits were removed. Results show that although individual vehicles reacted differently for each of the pollutants, elimination of engine deposits on average reduced HC emissions under hot running conditions by 29.4%, CO emissions under cold start conditions by 23.0% and CO emissions under hot running conditions by 35.5% （t 〈 0.05 in all cases）. No pollutant emissions increased with statistical significance （t 〈 0.05） after the removal of engine deposits. Variations of emission changes upon removal of engine deposits were observed. Such variations are in line with previous studies, implying that the impact patterns of engine deposits on vehicle emissions may be subject to many influencing factors that are not fully understood and difficult to control under all conditions. A statistical view of the impact of engine deposits on vehicle emissions may be appropriate for evaluation of emissions reductions across a city or a country. It is necessary to maintain sufficient and effective gasoline fuel detergency in practice to keep the engines clean and in tum reduce vehicle emissions.

VOCs evaporative emissions from vehicles in China:Species characteristics of different emission processes

Vehicle evaporation is an essential source of VOCs in cities but is not well understood in China.Reported emission factors from previous studies are not enough for understanding the atmospheric chemical process of vehicular evaporative VOCs.In this work,a serious of detailed VOCs speciation profiles are developed based on test processes and emission processes.A mass balance method was used to divide different emission processes during diurnal tests.The results show that headspace vapor of gasoline cannot represent the real-world vehicle evaporation because of the significant differences in VOCs speciation profiles,especially for aromatics.To further distinguish emissions from evaporation and exhaust,only the ratios of MTBE/benzene and MTBE/toluene can serve as indicators when considering species from all evaporative processes.Besides,emissions from different sources change significantly with the seasons.To solve these problems,we developed a monthly comprehensive evaporation speciation profile.The individual profiles at the emission processes are weighted by the emission of the in-use vehicle fleet in Beijing to derive the comprehensive speciation profile of evaporative VOCs.Ozone formation potential(OFP)and secondary organic aerosol potential(SOAP)were used to evaluate the environmental impact.For SOAP,100 g evaporative emissions are equal to 6.05-12.71 g toluene in different months,much higher than that given using headspace vapors,especially in winter(7.2 times higher in December).These findings would improve our understanding of the evaporative VOCs emissions in China and their environmental impacts(e.g.,O3 and SOA formation).

An estimation of vehicle kilometer traveled and on-road emissions using the traffic volume and travel speed on road links in Incheon City

The objective of this study is to estimate the vehicle kilometer traveled（VKT） and on-road emissions using the traffic volume in urban. We estimated two VKT; one is based on registered vehicles and the other is based on traffic volumes. VKT for registered vehicles was 2.11 times greater than that of the applied traffic volumes because each VKT estimation method is different. Therefore, we had to define the inner VKT is moved VKT inner in urban to compare two values. Also, we focused on freight modes because these are discharged much air pollutant emissions. From analysis results, we found middle and large trucks registered in other regions traveled to target city in order to carry freight, target city has included many industrial and logistics areas. Freight is transferred through the harbors,large logistics centers, or via locations before being moved to the final destination. During this process, most freight is moved by middle and large trucks, and trailers rather than small trucks for freight import and export. Therefore, these trucks from other areas are inflow more than registered vehicles. Most emissions from diesel trucks had been overestimated in comparison to VKT from applied traffic volumes in target city. From these findings, VKT is essential based on traffic volume and travel speed on road links in order to estimate accurately the emissions of diesel trucks in target city. Our findings support the estimation of the effect of on-road emissions on urban air quality in Korea.

Ammonia in urban atmosphere can be substantially reduced by vehicle emission control:A case study in Shanghai, China

To investigate the impact of emission controls on ammonia(NH_(3)) pollution in urban atmosphere, observation on NH_(3)(1 hr interval) was performed in Shanghai before, during and after the 2019 China International Import Expo (CIIE) event, along with measurements on inorganic ions, organic tracers and stable nitrogen isotope compositions of ammonium in PM_(2.5). NH_(3)during the CIIE period was 6.5±1.0μg/m^(3), which is 41% and 32% lower than that before and after the event, respectively. Such a decrease was largely ascribed to the emission controls in nonagricultural sources, of which contribution for measured NH_(3)in control phase abated by ~20% compared to that during uncontrol period. Molecular compositions of PAHs and hopanes further suggested a dominant role of the reduced vehicle emissions in the urban NH_(3)abatement during the CIIE period. Our results revealed that vehicle exhaust emission control is an effective way to mitigate NH_(3)pollution and improve air quality in Chinese urban areas.

Emissions of C_2-C_(12) hydrocarbons in the Hsuehshan tunnel,Taiwan

The concentrations of 56 hydrocarbons from C2 to C12 were measured simultaneously in the southbound bore,the northbound bore and the exhaust air shafts of the Hsuehshan tunnel near Yilan,Taiwan for 12 days during 2007 and 2008.A total of 60 integrated air samples were collected using stainless steel canisters and analyzed using GC/FID and GC/MS.The five most abundant species in all samples were ethylene,acetylene,isopentane,propylene and toluene.The exit/entrance ratios of total non-methane hydrocarbons（NMHC） concentration were 7.8 and 4.8 for the southbound and northbound bores,respectively.Furthermore,the exhaust from the vertical shafts a？ects air quality in the neighborhood.The most abundant species of emission rate（ER） was toluene（21.93-42.89 mg/sec）,followed by isopentane,ethylene,propylene and 1-butene,with ER ranging from 2.50 to 9.31 mg/sec.The species in the three exhaust air shafts showed that the reactivities of these emissions are similar to those of vehicle emissions.Notably,the control of emissions in the vertical shafts of the vehicle tunnel will be important in the future.

Review of the studies on emission evaluation approaches for operating vehicles

With the increasing international consensus concerning the negative effects of climate change,reducing greenhouse gases has become a higher priority in government policies and research committees.The transportation sector generates approximately 29%of the total greenhouse gas emissions and 25%of the global energy related carbon dioxide(CO2)emissions.Thus,it is essential to understand the influencing factors of vehicle emissions and establish a corresponding evaluation model for the emission estimation of operating vehicles.This paper reviews different methods of measuring vehicle emissions,including laboratory measurements,on-road measurements,and tunnel measurements.Then,we summarize the factors affecting the emission evaluation of operating vehicles based on the vehicle operating features and road environment.Finally,the applications of vehicle emission evaluation models are analyzed,including the emission assessment of the vehicles operating at road segments and intersections.Based on this review,one can conclude that selecting different measurements will significantly impact the assessment of the vehicle emission results and the applicable scope of the measurements.Considering the different influencing factors of the operating vehicle emissions will have an impact on the model application of the vehicle emission evaluation.Moreover,several analysis methods for new technology vehicles can compensate for the potential lack in connectedness with the rapid development of new energy vehicle technology and the improvement of intelligent transportation systems(ITS).

Characteristics of the pollutant emissions in a tunnel of Shanghai on a weekday

Tunnel displays a typical semi-closed environment, and multitudes of the pollutants tend to accumulate. The samples of gaseous pollutants and particulate matter （PM） were collected from the Xiangyin tunnel at Shanghai to investigate the characteristics of the pollutant emissions. The results indicated that both gaseous pollutants and PM exhibited much higher concentrations during the rush hours in the morning and at night due to vehicle emission. Two peaks of the PM concentration were observed in the scope of 0.7-1.1 and 3.3-4.7 μm, accounting for 14.6% and 20.3% of the total concentrations, respectively. Organic matter （OM）, EC, and many water-soluble ions were markedly higher at the rush hours in the morning than those at night, implicating comprehensive effects of vehicle types and traffic volume. The particle number concentrations exhibited two peaks at Aitken mode （25 nm and 100 rim） and accumulation mode （600 nm）, while the particle volume concentration displayed high values at the accumulation mode （100-500 nm） and coarse mode （2.5-4.0 μm）. The peak around 100 nm was detected in the morning rush hours, but it diminished with the decrease of the traffic volume. Individual-particle analysis revealed that main particles in the tunnel were Fe-rich particles, K-rich particles, mineral particles, Ca-S rich particles and A1-Si particles. The particles collected at the rush hours displayed marked different morphologies, element concentrations and particle sizes compared to the ones collected at the non-rush period. The data presented herein could shed a light on the feature of vehicle emissions.

Rural vehicle emission as an important driver for the variations of summertime tropospheric ozone in the Beijing-Tianjin-Hebei region during 2014-2019

Tropospheric ozone(O_(3))pollution is increasing in the Beijing-Tianjin-Hebei(BTH)region despite a significant decline in atmospheric fine aerosol particles(PM_(2.5))in recent years.However,the intrinsic reason for the elevation of the regional O_(3)is still unclear.In this study,we analyzed the spatio-temporal variations of tropospheric O_(3)and relevant pollutants(PM_(2.5),NO_(2),and CO)in the BTH region based on monitoring data from the China Ministry of Ecology and Environment during the period of 2014-2019.The results showed that summertime O_(3)concentrations were constant in Beijing(BJ,0.06μg/(m^(3)·year))but increased significantly in Tianjin(TJ,9.09μg/(m^(3)·year))and Hebei(HB,6.06μg/(m3·year)).Distinct O_(3)trends between Beijing and other cities in BTH could not be attributed to the significant decrease in PM_(2.5)(from-5.08 to-6.32μg/(m3·year))and CO(from-0.053 to-0.090 mg/(m^(3)·year))because their decreasing rates were approximately the same in all the cities.The relatively stable O_(3)concentrations during the investigating period in BJ may be attributed to a faster decreasing rate of NO_(2)(BJ:-2.55μg/(m^(3)·year);TJ:-1.16μg/(m^(3)·year);HB:-1.34μg/(m3·year)),indicating that the continued reduction of NOx will be an effective mitigation strategy for reducing regional O_(3)pollution.Significant positive correlations were found between daily maximum8 hr average(MDA8)O_(3)concentrations and vehicle population and highway freight transportation in HB.Therefore,we speculate that the increase in rural NO_(x)emissions due to the increase in vehicle emissions in the vast rural areas around HB greatly accelerates regional O_(3)formation,accounting for the significant increasing trends of O_(3)in HB.

Development of database of real-world diesel vehicle emission factors for China

A database of real-world diesel vehicle emission factors, based on type and technology, has been developed following tests on more than 300 diesel vehicles in China using a portable emission measurement system. The database provides better understanding of diesel vehicle emissions under actual driving conditions. We found that although new regulations have reduced real-world emission levels of diesel trucks and buses significantly for most pollutants in China, NOx emissions have been inadequately controlled by the current standards, especially for diesel buses, because of bad driving conditions in the real world. We also compared the emission factors in the database with those calculated by emission factor models and used in inventory studies. The emission factors derived from COPERT（Computer Programmer to calculate Emissions from Road Transport） and MOBILE may both underestimate real emission factors, whereas the updated COPERT and PART5（Highway Vehicle Particulate Emission Modeling Software） models may overestimate emission factors in China. Real-world measurement results and emission factors used in recent emission inventory studies are inconsistent,which has led to inaccurate estimates of emissions from diesel trucks and buses over recent years. This suggests that emission factors derived from European or US-based models will not truly represent real-world emissions in China. Therefore, it is useful and necessary to conduct systematic real-world measurements of vehicle emissions in China in order to obtain the optimum inputs for emission inventory models.