An alluvium with a sandy aquifer at the bottom,but lacking an effective impermeable layer between the sandy aquifer and bedrock is referred to as a special alluvial stratum.Impacted by the drainage of the aquifer due ...An alluvium with a sandy aquifer at the bottom,but lacking an effective impermeable layer between the sandy aquifer and bedrock is referred to as a special alluvial stratum.Impacted by the drainage of the aquifer due to mining activities,a shaft wall in this special alluvial stratum will be subject to a downward load by an additional vertical force which must be taken into consideration in the design of the shaft wall.The complexity of interaction between shaft wall and the surrounding walls makes it extremely difficult to determine this additional vertical force.For a particular shaft wall in an extra-thick alluvium and assuming that the friction coefficient between shaft wall and stratum does not change with depth,an analysis of a numerical simulation of the stress within the shaft wall has been carried out.Growth and size of the additional vertical stress have been obtained,based on specific values of the friction coefficient,the modulus of elasticity of the drainage layer and the thickness of the drainage layer.Subsequently, the safety of shaft walls with different structural types was studied and a more suitable structural design,providing an important basis for the design of shaft walls,is promoted.展开更多
In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dyna...In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dynamics (CFD). The influences of design parameters on flow fields and the mixing effect are analyzed. Firstly,the prediction capability of the turbulence model adopted in simulations is evaluated. And then,the mesh independence is checked up. Finally,the flow fields in various dimensionless blade diameters and dimensionless shaft spans are numerically simulated respectively. The results have shown that the numerical simulation method based on CFD is a feasible assistance for the optimal designs of mixers. Moreover,the optimal design of the blade diameter should take into account both the flow field and the power consumption. The optimization of the shaft span is to achieve a relatively even distribution of the flow field without any rupture. With the consideration of an optimal design,the dimensionless blade diameter and dimensionless shaft span should be 0.45 and 0.57 respectively in the case.展开更多
The model of skaft lining under force is developed on the basis of the special stratum condition led to sbart cracking- The model is broken into 3 sub-questions to solve separately. According to the principle of super...The model of skaft lining under force is developed on the basis of the special stratum condition led to sbart cracking- The model is broken into 3 sub-questions to solve separately. According to the principle of superposition and strain compatibility, a second kind Fredholm integral equation is generated.A theoretical solution to vertical additional force on shaft lining is obtained by numerical method to the integral equation.展开更多
The spatial and temporal distributions of new production vary largely in different sea areas. To understand the level of new production in the sea area studied better, an estimate of new production must be obtained in...The spatial and temporal distributions of new production vary largely in different sea areas. To understand the level of new production in the sea area studied better, an estimate of new production must be obtained in large spatial and temporal scales. The ~234Th/ ~238U disequilibrium is an effective method for the study of new production. Two sampling strategies, vertically integrated sampling ap proach based on trapezoidal integration principle and discrete layer sampling approach, were compared in the studies of the xiamen Bay and the northern South China Sea. The scavenging fluxes and removal fluxes of ~234Th and the residence times for dissolved and particulate ~234Th were calculated. The coinci dent results from two Sampling approach suggest that vertically integrated sampling approach is not only effective and reliable, but also significantly reduces the number and volume of samples. It allows us to study new production by ba ^(234)Th - ^(238)U disequilibria in large spatial scale.展开更多
The damage of the overburden is a complex nonliear mechanical problem. To immediately master the stress state of the vertical shaft in process of the damage of overburden, and protect the shaft, in this paper, a serie...The damage of the overburden is a complex nonliear mechanical problem. To immediately master the stress state of the vertical shaft in process of the damage of overburden, and protect the shaft, in this paper, a series of new type of rock mass stress and strain compatible sensors are used. The vertical shaft wall mechanical parameter and surrounding mechanical parameter are calculated by the result of the measurement. A set of the calculation method of the vertical shaft and surrounding rock parameter are defined.展开更多
Vertical shaft is main form of drivage in deep mineral depoist. They also serve as the entrance into and the exit from the underground mine. The main problems in shaft and tunnel engineering is to solve the contradict...Vertical shaft is main form of drivage in deep mineral depoist. They also serve as the entrance into and the exit from the underground mine. The main problems in shaft and tunnel engineering is to solve the contradiction between drivage and lining. The measurement of blasting vibration affecting concrete lining strength of vertical shaft is carried out in experiment and theory in this paper.展开更多
In order to study the effect of temperature difference load （TDL） along the vertical direction of a simply supported beam bridge section on the vertical irregularity, a rail-bridge-piers calculation model was establ...In order to study the effect of temperature difference load （TDL） along the vertical direction of a simply supported beam bridge section on the vertical irregularity, a rail-bridge-piers calculation model was established. Taking 32 m simply supported box beam bridge which is widely used in the construction of pas- senger dedicated line in China as an example, influences of the temperature variation between the bottom and top of the bridge, temperature curve index, type of temperature gradient, and beam height on track vertical irregularity were analyzed with the model. The results show that TDL has more effects on long wave track irregularity than on short one, and the wavelength mainly affected is approxi- mately equal to the beam span. The amplitude of irregu- larity caused by TDL is largely affected by the temperature variation, temperature curve index, and type of temperature gradient, so it is necessary to monitor the temperaturedistribution of bridges in different regions to provide accurate calculation parameters. In order to avoid the irregularity exceeding the limit values, the height of 32, 48, and 64 m simply supported box beam bridges must not be less than 2.15, 3.2, and 4.05 m, respectively.展开更多
文摘An alluvium with a sandy aquifer at the bottom,but lacking an effective impermeable layer between the sandy aquifer and bedrock is referred to as a special alluvial stratum.Impacted by the drainage of the aquifer due to mining activities,a shaft wall in this special alluvial stratum will be subject to a downward load by an additional vertical force which must be taken into consideration in the design of the shaft wall.The complexity of interaction between shaft wall and the surrounding walls makes it extremely difficult to determine this additional vertical force.For a particular shaft wall in an extra-thick alluvium and assuming that the friction coefficient between shaft wall and stratum does not change with depth,an analysis of a numerical simulation of the stress within the shaft wall has been carried out.Growth and size of the additional vertical stress have been obtained,based on specific values of the friction coefficient,the modulus of elasticity of the drainage layer and the thickness of the drainage layer.Subsequently, the safety of shaft walls with different structural types was studied and a more suitable structural design,providing an important basis for the design of shaft walls,is promoted.
基金Sponsored by the Science and Technology Projects of Heilongjiang Province (Grant No.GB07C20202 and LC06C16)
文摘In the paper the three-dimensional flow fields are numerically simulated in the vertical-shaft mechanical mix tank of a water treatment plant by means of FLUENT software based on the method of Computational Fluid Dynamics (CFD). The influences of design parameters on flow fields and the mixing effect are analyzed. Firstly,the prediction capability of the turbulence model adopted in simulations is evaluated. And then,the mesh independence is checked up. Finally,the flow fields in various dimensionless blade diameters and dimensionless shaft spans are numerically simulated respectively. The results have shown that the numerical simulation method based on CFD is a feasible assistance for the optimal designs of mixers. Moreover,the optimal design of the blade diameter should take into account both the flow field and the power consumption. The optimization of the shaft span is to achieve a relatively even distribution of the flow field without any rupture. With the consideration of an optimal design,the dimensionless blade diameter and dimensionless shaft span should be 0.45 and 0.57 respectively in the case.
文摘The model of skaft lining under force is developed on the basis of the special stratum condition led to sbart cracking- The model is broken into 3 sub-questions to solve separately. According to the principle of superposition and strain compatibility, a second kind Fredholm integral equation is generated.A theoretical solution to vertical additional force on shaft lining is obtained by numerical method to the integral equation.
基金National Natural Science Foundation of China! 49676296National Scientific and Technical Project! 97-926-04-02.
文摘The spatial and temporal distributions of new production vary largely in different sea areas. To understand the level of new production in the sea area studied better, an estimate of new production must be obtained in large spatial and temporal scales. The ~234Th/ ~238U disequilibrium is an effective method for the study of new production. Two sampling strategies, vertically integrated sampling ap proach based on trapezoidal integration principle and discrete layer sampling approach, were compared in the studies of the xiamen Bay and the northern South China Sea. The scavenging fluxes and removal fluxes of ~234Th and the residence times for dissolved and particulate ~234Th were calculated. The coinci dent results from two Sampling approach suggest that vertically integrated sampling approach is not only effective and reliable, but also significantly reduces the number and volume of samples. It allows us to study new production by ba ^(234)Th - ^(238)U disequilibria in large spatial scale.
文摘The damage of the overburden is a complex nonliear mechanical problem. To immediately master the stress state of the vertical shaft in process of the damage of overburden, and protect the shaft, in this paper, a series of new type of rock mass stress and strain compatible sensors are used. The vertical shaft wall mechanical parameter and surrounding mechanical parameter are calculated by the result of the measurement. A set of the calculation method of the vertical shaft and surrounding rock parameter are defined.
文摘Vertical shaft is main form of drivage in deep mineral depoist. They also serve as the entrance into and the exit from the underground mine. The main problems in shaft and tunnel engineering is to solve the contradiction between drivage and lining. The measurement of blasting vibration affecting concrete lining strength of vertical shaft is carried out in experiment and theory in this paper.
基金supported by the National Science Foundation (U1234201)the Doctorial Innovation Fund of Southwest Jiaotong University
文摘In order to study the effect of temperature difference load （TDL） along the vertical direction of a simply supported beam bridge section on the vertical irregularity, a rail-bridge-piers calculation model was established. Taking 32 m simply supported box beam bridge which is widely used in the construction of pas- senger dedicated line in China as an example, influences of the temperature variation between the bottom and top of the bridge, temperature curve index, type of temperature gradient, and beam height on track vertical irregularity were analyzed with the model. The results show that TDL has more effects on long wave track irregularity than on short one, and the wavelength mainly affected is approxi- mately equal to the beam span. The amplitude of irregu- larity caused by TDL is largely affected by the temperature variation, temperature curve index, and type of temperature gradient, so it is necessary to monitor the temperaturedistribution of bridges in different regions to provide accurate calculation parameters. In order to avoid the irregularity exceeding the limit values, the height of 32, 48, and 64 m simply supported box beam bridges must not be less than 2.15, 3.2, and 4.05 m, respectively.
