Lateral Oxidation in Vertical Cavity Surface Emitting Lasers

Lateral oxidation in vertical cavity surface emitting lasers （VCSELs） is described,and its characteristics are investigated.A linear growth law is found for stripe mesas. However, oxide growth （above 435℃ ） follows a nonlinear law for the two geometry mesa structures which we employ in VCSEL. Theoretical analysis indicates that mesa structure geometry influences oxide growth rate at higher temperatures.

High Slope Efficiency and High Power 850nm Oxide-Confined Vertical Cavity Surface Emitting Lasers

High slope efficiency and high power selected oxide-confined 850nm VCSELs grown by MOCVD are reported.The slope efficiency and the threshold current respectively are 0 82mW/mA and 2 59mA with a 9μm diameter oxidation aperture at 25℃.The maximum power of 16mW is obtained at 23mA current bias.The minimum threshold current can be as low as 570μA with a 5μm diameter oxidation aperture at 25℃.The maximum saturated power is 5 5mW.

Surface seasonal mass changes and vertical crustal deformation in North China from GPS and GRACE measurements

The Earth is an elastic body,and the surface mass loading changes will lead to elastic loading deformation on the surface of the Earth.In this study,we investigated the surface seasonal mass changes and vertical crustal deformation in North China using the data obtained by the techniques of the Global Positioning System(GPS),Gravity Recovery and Climate Experiment(GRACE)and Surface Loading Models(SLMs).The seasonal annual signal and semi-annual signal obtained by the three techniques show strong correlations.The average value of the weighted root-mean-square(WRMS)of the all 30 sites is 58%after deducting the GRACE-obtained vertical deformation from the GPS-derived vertical deformation.However,the consistency of results between GPS and SLMs is not so good,with a 31%mean WRMS reduction,due to the fact that the global SLMs perform not well in North China.The GRACEmeasured long-term trend is deducted from the GPS-obtained vertical rates to reveal the crustal displacement caused by the underground factors such as tectonic movement and groundwater in North China.The results show that the rates of stations HECX and TJBH are very large,more than 10 mm/yr,which suggests that the surface subsidence is caused by excessive exploitation of groundwater.

Exploitation technology of pressure relief coalbed methane in vertical surface wells in the Huainan coal mining area

Exploitation technology of pressure relief coalbed methane in vertical surface wells is a new method for exploration of gas and coalbed methane exploitation in mining areas with high concentrations of gas, where tectonic coal developed. Studies on vertical surface well technology in the Huainan Coal Mining area play a role in demonstration in the use of clean, new energy resources, preventing and reducing coal mine gas accidents and protecting the environment. Based on the practice of gas drainage engineering of pressure relief coalbed methane in vertical surface wells and combined with relative geological and exploration en- gineering theories, the design principles of design and structure of wells of pressure relief coalbed methane in vertical surface wells are studied. The effects of extraction and their causes are discussed and the impact of geological conditions on gas production of the vertical surface wells are analyzed. The results indicate that in mining areas with high concentrations of gas, where tectonic coal developed, a success rate of pressure relief coalbed methane in surface vertical well is high and single well production usually great. But deformation due to coal exploitation could damage boreholes and cause breaks in the connection between aquifers and bore-holes, which could induce a decrease, even a complete halt in gas production of a single well. The design of well site location and wellbore configuration are the key for technology. The development of the geological conditions for coalbed methane have a significant effect on gas production of coalbed methane wells.

Contribution of surface wave-induced vertical mixing to heat content in global upper ocean

Compared with observations,the simulated upper ocean heat content(OHC)determined from climate models shows an underestimation bias.The simulation bias of the average annual water temperature in the upper 300 m is 0.2℃lower than the observational results.The results from our two numerical experiments,using a CMIP5 model,show that the non-breaking surface wave-induced vertical mixing can reduce this bias.The enhanced vertical mixing increases the OHC in the global upper ocean(65°S–65°N).Using non-breaking surface wave-induced vertical mixing reduced the disparity by 30%to 0.14℃.The heat content increase is not directly induced by air-sea heat fluxes during the simulation period,but is the legacy of temperature increases in the first 150 years.During this period,additional vertical mixing was initially included in the climate model.The non-breaking surface wave-induced vertical mixing improves the OHC by increasing the air-sea heat fluxes in the first 150 years.This increase in air-sea heat fluxes warms the upper ocean by 0.05–0.06℃.The results show that the incorporation of vertical mixing induced by nonbreaking surface waves in our experiments can improve the simulation of OHC in the global upper ocean.

Green Vertical‑Cavity Surface‑Emitting Lasers Based on InGaN Quantum Dots and Short Cavity

Room temperature low threshold lasing of green GaNbased vertical cavity surface emitting laser(VCSEL)was demonstrated under continuous wave(CW)operation.By using self-formed InGaN quantum dots(QDs)as the active region,the VCSEL emitting at 524.0 nm has a threshold current density of 51.97 A cm^(-2),the lowest ever reported.The QD epitaxial wafer featured with a high IQE of 69.94%and theδ-function-like density of states plays an important role in achieving low threshold current.Besides,a short cavity of the device(~4.0λ)is vital to enhance the spontaneous emission coupling factor to 0.094,increase the gain coefficient factor,and decrease the optical loss.To improve heat dissipation,AlN layer was used as the current confinement layer and electroplated copper plate was used to replace metal bonding.The results provide important guidance to achieving high performance GaN-based VCSELs.

Thermal Analysis of Implant-Defined Vertical Cavity Surface Emitting Laser Array

A three-dimensional electrical-thermal coupling model based on the finite element method is applied to study thermal properties of implant-defined vertical cavity surface emitting laser （VCSEL） arrays. Several parameters including inter-element spacing, scales, injected current density and substrate temperature are considered. The actual temperatures obtained through experiment are in excellent agreement with the calculated results, which proves the accuracy of the model. Due to the serious thermal problem, it is essential to design arrays of low self-heating. The analysis can provide a foundation for designing VCSEL arrays in the future.

Power dissipation in oxide-confined 980-nm vertical-cavity surface-emitting lasers

We presented 980-nm oxide-confined vertical-cavity surface-emitting lasers （VCSELs） with a 16 -um oxide aperture. Optical power, voltage, and emission wavelength are measured in an ambient temperature range of 5 ℃-80 ℃. Measurements combined with an empirical model are used to analyse the power dissipation in the device and the physical mechanism contributing to the thermal rollover phenomenon in VCSEL. It is found that the carrier leakage induced selfheating in the active region and the Joule heating caused by the series resistance are the main sources of power dissipation. In addition, carrier leakage induced self-heating increases as the injection current increases, resulting in a rapid decrease of the internal quantum efficiency, which is a dominant contribution to the thermal rollover of the VCSEL at a larger current. Our study provides useful guidelines to design a 980-nm oxide-confined VCSEL for thermal performance enhancement.

CAPILLARY EFFECT ON VERTICALLY EXCITED SURFACE WAVE IN CIRCULAR CYLINDRICAL VESSEL

In a vertically oscillating circular cylindrical container, singular perturbation theory of two-time scale expansions was developed in inviscid fluids to investigate the motion of single free surface standing wave including the effect of surface tension. A nonlinear slowly varying amplitude equation, which incorporates cubic nonlinear term, external excitation and the influence of surface tension, was derived from potential flow equation. The results show that, when forced frequency is lower, the effect of surface ten- sion on mode selection of surface wave is not important. However, when forced frequency is higher, the surface tension can not be neglected. This proved that the surface tension causes free surface returning to equilibrium location. In addition, due to considering the effect of surface tension, the theoretical result approaches to experimental results much more than that of no surface tension.

Polarization switching and synchronization of mutually coupled vertical-cavity surface-emitting semiconductor lasers

Polarization switching （PS） dynamics and synchronization performances of two mutually coupled vertical-cavity surface-emitting lasers （VCSELs） are studied theoretically in this paper. A group of dimensionless rate equations is derived to describe our model. While analysing the PS characteristics, we focus on the effects of coupling rate and frequency detuning regarding different mutual injection types. The results indicate that the x-mode injection defers the occurrence of PS, while the y-mode injection leads the PS to occur at a lower current. Strong enough polarization-selective injection can suppress the PS. Moreover, if frequency detuning is considered, the effects of polarization-selective mutual injection will be weakened. To evaluate the synchronization performance, the correlation coefficients and output dynamics of VCSELs with both pure mode and mixed mode polarizations are given. It is found that performance of complete synchronization is sensitive to the frequency mismatch but it is little affected by mixed mode polarizations, which is opposite to the case of injection-locking synchronization.

An efficient approach to characterizing and calculating carrier loss due to heating and barrier height variation in vertical-cavity surface-emitting lasers

It is important to determine quantitatively the internal carrier loss arising from heating and barrier height variation in a vertical-cavity surface-emitting quantum well laser （VCSEL）. However, it is generally difficult to realize this goal using purely theoretical formulas due to difficulty h, deriving the parameters relat^i~g to the quantum well structure. In this paper, we describe an efl：icient approach to characterizing and calculating the carrier loss due to the heating and the barrier height change in the VCSEL. In the method, the thermal carrier loss mechanism is combined with gain measurement and calculation. The carrier loss is re-characterized in a calculable form by constructing the threshold current and gain detuning-related loss current using the measured gain data and then substituting them for the quantum well-related parameters in the formula. The result can be expressed as a product of an exponential weight factor linked to the barrier height change and the difference between the threshold current and gain detuning-related loss current. The gain variation at cavity frequency due to thermal carrier loss and gain detuning processes is measured by using an AllnGaAs-AIGaAs VCSEL structure. This work provides a useful approach to analysing threshold and loss properties of the VCSEL, particularly, gain offset design for high temperature operation of VCSELs.

Co-variation of the surface wind speed and the sea surface temperature over mesoscale eddies in the Gulf Stream region:momentum vertical mixing aspect

The co-variation of surface wind speed and sea surface temperature (SST) over the Gulf Stream frontal region is investigated using high-resolution satellite measurements and atmospheric reanalysis data. Results show that the pattern of positive SST-surface wind speed correlations is anchored by strong SST gradient and marine atmospheric boundary layer (MABL) height front, with active warm and cold-ocean eddies around. The MABL has an obvious transitional structure along the strong SST front, with greater (lesser) heights over the north (south) side. The significant positive SST-surface wind-speed perturbation correlations are mostly found over both strong warm and cold eddies. The surface wind speed increases (decreases) about 0.32 (0.41) m/s and the MABL elevates (drops) approximate 55 (54) m per 1℃ of SST perturbation induced by warm (cold) eddies. The response of the surface wind speed to SST perturbations over the mesoscale eddies is mainly attributed to the momentum vertical mixing in the MABL, which is confirmed by the linear relationships between the downwind (crosswind) SST gradient and wind divergence (curl).

Micromechanical tunable vertical-cavity surface-emitting lasers

We report the study on a short wavelength-tunable vertical-cavity surface-emitting laser utilizing a monolithically integrated bridge tuning microelectromechanical system. A deformable-bridge top mirror suspended above an active region is utilized. Applied bridge-substrate bias produces an electrostatic force which reduces the spacing of air-gap and tunes the resonant wavelength toward a shorter wavelength （blue-shift）, Good laser characteristics are obtained： such as continuous tuning ranges over 11 nm near 940 nm for 0-9 V tuning bias, the peak output power near 1 mW and the full-width-half-maximum limited to approximately 3.2-6.8 rim. A detailed simulation of the micromechanical and optical characteristics of these devices is performed, and the ratio of bridge displacement to wavelength shift has been found to be 3：1.

Vertical cavity surface emitting laser transverse mode and polarization control by elliptical hole photonic crystal

The polarization of traditional photonic crystal（PC） vertical cavity surface emitting laser（VCSEL） is uncontrollable,resulting in the bit error increasing easily.Elliptical hole photonic crystal can control the transverse mode and polarization of VCSEL efficiently.We analyze the far field divergence angle,and birefringence of elliptical hole PC VCSEL.When the ratio of minor axis to major axis b/a = 0.7,the PC VCSEL can obtain single mode and polarization.According to the simulation results,we fabricate the device successfully.The output power is 1.7 mW,the far field divergence angle is less than 10°,and the side mode suppression ratio is over 30 dB.The output power in the Y direction is 20 times that in the X direction.

Investigation of the mode splitting induced by electro-optic birefringence in a vertical-cavity surface-emitting laser by polarized electroluminescence

The mode splitting induced by electro-optic birefringence in a P-I-N InGaAs/GaAs/A1GaAs vertical-cavity surface- emitting laser （VCSEL） has been studied by polarized electroluminescence （EL） at room temperature. The polarized EL spectra with E｜｜[110] and E ｜｜ [150] directions, are extracted for different injected currents. The mode splitting of the two orthogonal polarized modes for a VCSEL device is determined, and its value increases linearly with the increasing injected current due to electro-optic birefringence; This article demonstrates that the polarized EL is a powerful tool to study the mode splitting and polarization anisotropy of a VCSEL device.

Simulation of Far-Field Properties of Coherent Vertical Cavity Surface Emitting Laser Array

Far-field properties dependent on array scale, separation, element width and emitted wavelength are system atically analyzed theoretically and experimentally. An array model based on the finite-difference method is established to simulate the far-field profile of the coherent arrays. Some important conclusions are obtained. To achieve a higher quality beam, it is necessary to decrease separation between elements, or to increase the element width. Higher brightness can be achieved in the array with larger scale. Emitted wavelength also has an influence on the far-field profile. These analyses can be extended to the future design of coherent vertical cavity surface emitting laser arrays.

Separating emitted dust from the total suspension in airflow based on the characteristics of PM10 vertical concentration profiles on a Gobi surface in northwestern China

During aeolian processes,the two most critical factors related to dust emissions are soil particle and aggregate saltation,which greatly affect the vertical profiles of near-surface dust concentrations.In this study,we measured PM10 concentrations at four different heights(0.10,0.50,1.00 and 2.00 m)with and without continuous and simultaneous aeolian saltation processes on a Gobi surface in northwestern China from 31 March to 10 April,2017.We found that the vertical concentration profiles of suspended PM10 matched the log-law model well when there was no aeolian saltation.For the erosion process with saltation,we divided the vertical concentration profiles of PM10 into the saltation-affected layer and the airflow-transport layer according to two different dust sources(i.e.,locally emitted PM10 and upwind transported PM10).The transition height between the saltation-affected layer and the airflow-transport layer was not fixed and varied with saltation intensity.From this new perspective,we calculated the airflow-transport layer and the dust emission rate at different times during a wind erosion event occurred on 5 April 2017.We found that dust emissions during wind erosion are primarily controlled by saltation intensity,contributing little to PM10 concentrations above the ground surface compared to PM10 concentrations transported from upwind directions.As erosion progresses,the surface supply of erodible grains is the most crucial factor for saltation intensity.When there was a sufficient amount of erodible grains,there was a significant correlation among the friction velocity,saltation intensity and dust emission rate.However,when supply is limited by factors such as surface renewal or an increase in soil moisture,the friction velocity will not necessarily correlate with the other two factors.Therefore,for the Gobi surface,compared to limiting dust emissions from upwind directions,restricting the transport of suspended dust in its path is by far a more efficient and realistic option for small areas that are often exposed to dust storms.This study provides some theoretical basis for correctly estimating PM10 concentrations in the Gobi areas.

Development and Flow Modes of Vertical Taylor-Couette System with Free Surface

We have numerically and experimentally investigated the flow modes of Taylor-Couette system consisting of coaxial two cylinders with vertical axes. The inner cylinder rotates and the outer cylinder and the bottom end of the cylinders remain stationary. The upper top boundary is the free surface of the working liquid between the inner and outer cylinders and it contacts with the air. While this flow appears in fluid machinery and chemical reactors and includes industrial interests, it also contains problems of fluid mechanics, which is about the behavior of the free surface in the rotating field. In this paper, we concretely show the developments of the one cell mode flow and the three cell mode flow at a small aspect ratio. We also represent the bifurcation diagram of the flow at the moderate aspect ratio about 5.5. In the numerical simulation, the flow is rest in the initial state, and the inner cylinder is linearly or suddenly accelerated to attain a flow with a prescribed Reynolds number. When the acceleration of the inner cylinder is high, an imperfect bifurcation occurs and the flows of the secondary modes emerge. At high Reynolds numbers, the flow first has many vortices and then some of the vortices collapse and the final stable flow arises. The loci of the normal five cell mode, the anomalous six cell mode and the secondary seven cell mode are determined.

Beam Steering Analysis in Optically Phased Vertical Cavity Surface Emitting Laser Array

Beam steering in implant defined coherently coupled vertical cavity surface emitting laser （VCSEL） arrays is simulated using the FDTD solution software. Angular deflection dependent on relative phase differences among elements, inter-element spacing, element size and emitted wavelength is analyzed detailedly and systematically. We design and fabricate 1×2 implant defined VCSEL arrays for optimum beam steering performance. Electroni- cally controlled beam steering with a maximum deflection angle of 1.6° is successfully achieved in the 1 × 2 VCSEL arrays. The percentage of the power in the central lobe is above 39% when steering. The results show that the steering is controllable. Compared with other beam steering methods, the fabrication process is simple and of low cost.

Simplified modeling of frequency behavior in photonic crystal vertical cavity surface emitting laser with tunnel injection quantum dot in active region

In this work, the characteristics of the photonic crystal tunneling injection quantum dot vertical cavity surface emitting lasers（Ph C-TIQD-VCSEL） are studied through analyzing a modified modulation transfer function. The function is based on the rate equations describing the carrier dynamics at different energy levels of dot and injector well. Although the frequency modulation response component associated with carrier dynamics in wetting layer（WL） and at excited state（ES） levels of dots limits the total bandwidth in conventional QD-VCSEL, our study shows that it can be compensated for by electron tunneling from the injector well into the dot in TIQD structure. Carrier back tunneling time is one of the most important parameters, and by increment of that, the bias current dependence of the total bandwidth will be insignificant. It is proved that at high bias current, the limitation of the WL-ES level plays an important role in reducing the total bandwidth and results in rollovers on 3-d B bandwidth-I curves. In such a way, for smaller air hole diameter of photonic crystal, the effect of this reduction is stronger.