Avirtual wall thicknessmethod is developed to simulate the temperature field of turbine bladeswith thermal barrier coatings(TBCs),to simplify the modeling process and improve the calculation efficiency.The results sho...Avirtual wall thicknessmethod is developed to simulate the temperature field of turbine bladeswith thermal barrier coatings(TBCs),to simplify the modeling process and improve the calculation efficiency.The results show that the virtualwall thickness method can improve themesh quality by 20%,reduce the number ofmeshes by 76.7%and save the calculation time by 35.5%,compared with the traditional real wall thickness method.The average calculation error of the two methods is between 0.21%and 0.93%.Furthermore,the temperature at the blade leading edge is the highest and the average temperature of the blade pressure surface is higher than that of the suction surface under a certain service condition.The blade surface temperature presents a high temperature at both ends and a low temperature in themiddle height when the temperature of incoming gas is uniformand constant.The thermal insulation effect of TBCs is the worst near the air film hole,and the best at the blade leading edge.According to the calculated temperature field of the substrate-coating system,the highest thermal insulation temperature of the TC layer is 172.01 K,and the thermal insulation proportions of TC,TGO and BC are 93.55%,1.54%and 4.91%,respectively.展开更多
With the rapid development of China’s civil aviation industry,the teaching method of operating knowledge of flight principles has changed greatly,which creates a good implementation environment to improve the safety ...With the rapid development of China’s civil aviation industry,the teaching method of operating knowledge of flight principles has changed greatly,which creates a good implementation environment to improve the safety of civil aviation in our country.At present,the main training content of air route transport pilots in China is basic aviation theory,initial flight training,airline modification,etc.The principles of flight control are an important part of basic aviation theoretical knowledge training,which will involve a large number of flight technology training content,instructors will also be based on the pilot type.Teaching flight control theory and practical knowledge requires relatively high theoretical learning ability of students,and the learning effect of this part of theoretical knowledge will directly affect the quality of subsequent learning,but also directly affect the effectiveness of flight training.This paper focuses on the analysis of the basic concepts of flight control,studies the existing problems in the teaching of flight control principles,summarizes the teaching measures of flight control principles,aiming to provide a reference to teaching personnel.展开更多
Objective:To compare the efficacy of anal adenectomy with virtual hanging wire and anal fistulotomy in the treatment of low anal fistula in infants and children.Methods:60 children with low anal fistula who were admit...Objective:To compare the efficacy of anal adenectomy with virtual hanging wire and anal fistulotomy in the treatment of low anal fistula in infants and children.Methods:60 children with low anal fistula who were admitted to our hospital from October 2021 to March 2022 and met the inclusion criteria were randomly divided into two groups of 30 cases each;the treatment group was treated with anal adenectomy and virtual hanging wire surgery,and the control group was treated with anal fistula resection.The clinical efficacy after treatment was compared.Results:The total effective rate of both groups was 96.67%and the difference between the two groups was not statistically significant(P>0.05).The postoperative pain score of the treatment group was lower than that of the control group(P<0.05).The length of hospitalization and healing time of the treatment group was lower than that of the control group(P<0.05).The anal function of the patients in both groups was normal,and there was no adverse reaction.Conclusion:Anal gland excision and virtual hanging surgery for the treatment of low anal fistula in infants and children have the advantages of mild pain,reduced length of hospitalization,short healing time,and better patient experience as compared to anal fistula excision.展开更多
In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method (DEM). A digital specimen g...In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method (DEM). A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition (TTS) principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element (DE) viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.展开更多
In order to study fracture behaviors of asphalt mixtures, virtual tests of the two-dimensional(2D) microstructure based on the discrete element method( DEM) are designed. The virtual structure of the 2D digital sp...In order to study fracture behaviors of asphalt mixtures, virtual tests of the two-dimensional(2D) microstructure based on the discrete element method( DEM) are designed. The virtual structure of the 2D digital specimen of asphalt mixture is generated based on a particle generation program, in which the gradation and the irregular shapes of aggregates are considered. With the 2D digital specimens, a DEM-based mixture model is established and center-point beam fracture simulation tests are conducted by the DEM. Meanwhile, a series of calibration tests are carried out in laboratory to evaluate the DEM model and validate the methods of virtual fracture tests. The test results indicate that the fracture intensity of asphalt mixtures predicted by the DEM matches very well with the intensity obtained in laboratory. It is concluded that the microstructural virtual tests can be used as a supplemental tool to evaluate fracture properties of asphalt mixtures.展开更多
Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials ...Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q, Q, Q, Q) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q, Q, Q, Q) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q, Q, Q, Q) were determined from the test with an angle of 27?.展开更多
By virtue of the comparability between the wave superposition method and the dynamic analysis of structures, a general format for overcoming the non-uniqueness of solution induced by the wave superposition method at t...By virtue of the comparability between the wave superposition method and the dynamic analysis of structures, a general format for overcoming the non-uniqueness of solution induced by the wave superposition method at the eigenfrequencies of the corresponding interior problems is proposed. By adding appropriate damp to the virtual source system of the wave superposition method, the unique solutions for all wave numbers can be ensured. Based on this thought, a novel method-wave superposition method with complex radius vector is constructed. Not only is the computational time of this method approximately equal to that of the standard wave superposition method, but also the accuracy is much higher compared with other correlative methods. Finally, by taking the pulsating sphere and oscillating sphere as examples, the results of calculation show that the present method can effectively overcome the non-uniqueness problem.展开更多
The objective of this work is to model the microstructure of asphalt mixture and build virtual test for asphalt mixture by using Particle Flow Code in three dimensions(PFC^(3D))based on three-dimensional discrete elem...The objective of this work is to model the microstructure of asphalt mixture and build virtual test for asphalt mixture by using Particle Flow Code in three dimensions(PFC^(3D))based on three-dimensional discrete element method.A randomly generating algorithm was proposed to capture the three-dimensional irregular shape of coarse aggregate.And then,modeling algorithm and method for graded aggregates were built.Based on the combination of modeling of coarse aggregates,asphalt mastic and air voids,three-dimensional virtual sample of asphalt mixture was modeled by using PFC^(3D).Virtual tests for penetration test of aggregate and uniaxial creep test of asphalt mixture were built and conducted by using PFC^(3D).By comparison of the testing results between virtual tests and actual laboratory tests,the validity of the microstructure modeling and virtual test built in this study was verified.Additionally,compared with laboratory test,the virtual test is easier to conduct and has less variability.It is proved that microstructure modeling and virtual test based on three-dimensional discrete element method is a promising way to conduct research of asphalt mixture.展开更多
A novel numerical method for eliminating the singular integral and boundary effect is processed. In the proposed method, the virtual boundaries corresponding to the numbers of the true boundary arguments are chosen to...A novel numerical method for eliminating the singular integral and boundary effect is processed. In the proposed method, the virtual boundaries corresponding to the numbers of the true boundary arguments are chosen to be as simple as possible. An indirect radial basis function network (IRBFN) constructed by functions resulting from the indeterminate integral is used to construct the approaching virtual source functions distributed along the virtual boundaries. By using the linear superposition method, the governing equations presented in the boundaries integral equations (BIE) can be established while the fundamental solutions to the problems are introduced. The singular value decomposition (SVD) method is used to solve the governing equations since an optimal solution in the least squares sense to the system equations is available. In addition, no elements are required, and the boundary conditions can be imposed easily because of the Kronecker delta function properties of the approaching functions. Three classical 2D elasticity problems have been examined to verify the performance of the method proposed. The results show that this method has faster convergence and higher accuracy than the conventional boundary type numerical methods.展开更多
A novel polygonal finite element method (PFEM) based on partition of unity is proposed, termed the virtual node method (VNM). To test the performance of the present method, numerical examples are given for solid m...A novel polygonal finite element method (PFEM) based on partition of unity is proposed, termed the virtual node method (VNM). To test the performance of the present method, numerical examples are given for solid mechanics problems. With a polynomial form, the VNM achieves better results than those of traditional PFEMs, including the Wachspress method and the mean value method in standard patch tests. Compared with the standard triangular FEM, the VNM can achieve better accuracy. With the ability to construct shape functions on polygonal elements, the VNM provides greater flexibility in mesh generation. Therefore, several fracture problems are studied to demonstrate the potential implementation. With the advantage of the VNM, the convenient refinement and remeshing strategy are applied.展开更多
Based on foreign and domestic literature about teaching theories and simulation application,advantages and disadvantages of simulation teaching and other teaching methods were compared,organization forms and efficienc...Based on foreign and domestic literature about teaching theories and simulation application,advantages and disadvantages of simulation teaching and other teaching methods were compared,organization forms and efficiency of simulation teaching in network environment discussed,students' learning patterns and styles summarized,and the theoretical research foundation for the simulation teaching and students' learning system in network environment established.Common problems of simulation teaching and corresponding students' learning styles were discussed,application and supervision system of simulation teaching established,students' learning styles innovated.Views and innovations of virtual simulation teaching in simulation teaching of landscape architecture were given,and the research framework sorted out as reference.展开更多
Energy methods and the principle of virtual work are commonly used for obtaining solutions of boundary value problems (BVPs) and initial value problems (IVPs) associated with homogeneous, isotropic and non-homogeneous...Energy methods and the principle of virtual work are commonly used for obtaining solutions of boundary value problems (BVPs) and initial value problems (IVPs) associated with homogeneous, isotropic and non-homogeneous, non-isotropic matter without using (or in the absence of) the mathematical models of the BVPs and the IVPs. These methods are also used for deriving mathematical models for BVPs and IVPs associated with isotropic, homogeneous as well as non-homogeneous, non-isotropic continuous matter. In energy methods when applied to IVPs, one constructs energy functional (<i>I</i>) consisting of kinetic energy, strain energy and the potential energy of loads. The first variation of this energy functional (<em>δI</em>) set to zero is a necessary condition for an extremum of <i>I</i>. In this approach one could use <i>δI</i> = 0 directly in constructing computational processes such as the finite element method or could derive Euler’s equations (differential or partial differential equations) from <i>δI</i> = 0, which is also satisfied by a solution obtained from <i>δI</i> = 0. The Euler’s equations obtained from <i>δI</i> = 0 indeed are the mathematical model associated with the energy functional <i>I</i>. In case of BVPs we follow the same approach except in this case, the energy functional <i>I</i> consists of strain energy and the potential energy of loads. In using the principle of virtual work for BVPs and the IVPs, we can also accomplish the same as described above using energy methods. In this paper we investigate consistency and validity of the mathematical models for isotropic, homogeneous and non-isotropic, non-homogeneous continuous matter for BVPs that are derived using energy functional consisting of strain energy and the potential energy of loads. Similar investigation is also presented for IVPs using energy functional consisting of kinetic energy, strain energy and the potential energy of loads. The computational approaches for BVPs and the IVPs designed using energy functional and principle of virtual work, their consistency and validity are also investigated. Classical continuum mechanics (CCM) principles <i>i.e.</i> conservation and balance laws of CCM with consistent constitutive theories and the elements of calculus of variations are employed in the investigations presented in this paper.展开更多
Concepts for a virtual 3D space and a hyper-sphere are proposed and the formulae for determining the computable nodes of the mesh are derived.Then a new optimization design method('Virtual Mesh Method'or V.M.M...Concepts for a virtual 3D space and a hyper-sphere are proposed and the formulae for determining the computable nodes of the mesh are derived.Then a new optimization design method('Virtual Mesh Method'or V.M.M)is developed.Three examples are given,showing that the method proposed is especially suitable for the optimized design of complex structures,and that the global approximate optimal solution can be searched with remarkably reduced computational work.展开更多
The virtual displacement principle of elasto-plastic damage mechanics is presented. A linear complementary method for elasto-plastic damage problem is proposed by using FEM technique. This method is applicable to solv...The virtual displacement principle of elasto-plastic damage mechanics is presented. A linear complementary method for elasto-plastic damage problem is proposed by using FEM technique. This method is applicable to solving the damage structure analysis of hardened and softened nonlinear material.展开更多
Thermal barrier coatings (TBCs) are widely applied in thermal components to protect metallic components. Owing to the complex layered structure of TBCs and difficult preparation of coating, the mechanical characteriza...Thermal barrier coatings (TBCs) are widely applied in thermal components to protect metallic components. Owing to the complex layered structure of TBCs and difficult preparation of coating, the mechanical characterization of TBCs should be of primary importance. With regard to TBCs, this study deals with the constitutive parameters identification of bi-material. Considering the complex construction and boundary of bi material, the virtual fields method (VFM) was employed in this study. A methodology based on the optimized virtual fields method combined with moire interferometry was proposed for the constitutive parameters identification of bi-material. The feasibility of this method is verified using simulated deformation fields of a two-layer material subjected to three point ben ding loading. As an application, the deformation fields of the TBC specimens were measured by moire interferometry. Then, lhe mechanical parameters of the coating were identified by the proposed method. The identification results indicate that Young's modulus of the TBC top coating is 89.91 GPa, and its Poisson's ratio is 0.23.展开更多
This paper aims to apply a virtual boundary element method(VBEM)to solve the inverse problems of three-dimensional heat conduction in orthotropic media.This method avoids the singular integrations in the conventional ...This paper aims to apply a virtual boundary element method(VBEM)to solve the inverse problems of three-dimensional heat conduction in orthotropic media.This method avoids the singular integrations in the conventional boundary element method,and can be treated as a potential approach for solving the inverse problems of the heat conduction owing to the boundary-only discretization and semi-analytical algorithm.When the VBEM is applied to the inverse problems,the numerical instability may occur if a virtual boundary is not properly chosen.The method encounters a highly illconditioned matrix for the larger distance between the physical boundary and the virtual boundary,and otherwise is hard to avoid the singularity of the source point.Thus,it must adopt an appropriate regularization method to deal with the ill-posed systems of inverse problems.In this study,the VBEM and different regularization techniques are combined to model the inverse problem of three-dimensional heat conduction in orthotropic media.The proper regularization techniques not only make the virtual boundary to be allocated freer,but also solve the ill-conditioned equation of the inverse problem.Numerical examples demonstrate that the proposed method is efficient,accurate and numerically stable for solving the inverse problems of three-dimensional heat conduction in orthotropic media.展开更多
The virtual-ray method for treating HF electromagnetic scattering problems is derived from the plane wave of free space, and using this the plane wave scattering by an impedance wedge is studied. In the solution proce...The virtual-ray method for treating HF electromagnetic scattering problems is derived from the plane wave of free space, and using this the plane wave scattering by an impedance wedge is studied. In the solution process a novel concept of generalized circle is introduced so that the complete amplitude function is obtained. And a reasonable physical interpretation for the term W2, which was neglected previously, is given. The calculated results agree well with those of the analytical solution obtained by G.D. Maliuzhinets(1958).展开更多
In this paper, we discuss virtual element method (VEM) approximation of optimal control problem governed by Brinkman equations with control constraints. Based on the polynomial projections and variational discretizati...In this paper, we discuss virtual element method (VEM) approximation of optimal control problem governed by Brinkman equations with control constraints. Based on the polynomial projections and variational discretization of the control variable, we build up the virtual element discrete scheme of the optimal control problem and derive the discrete first order optimality system. A priori error estimates for the state, adjoint state and control variables in L<sup>2</sup> and H<sup>1</sup> norm are derived. The theoretical findings are illustrated by the numerical experiments.展开更多
Cloud computing involves remote server deployments with public net-work infrastructures that allow clients to access computational resources.Virtual Machines(VMs)are supplied on requests and launched without interacti...Cloud computing involves remote server deployments with public net-work infrastructures that allow clients to access computational resources.Virtual Machines(VMs)are supplied on requests and launched without interactions from service providers.Intruders can target these servers and establish malicious con-nections on VMs for carrying out attacks on other clustered VMs.The existing system has issues with execution time and false-positive rates.Hence,the overall system performance is degraded considerably.The proposed approach is designed to eliminate Cross-VM side attacks and VM escape and hide the server’s position so that the opponent cannot track the target server beyond a certain point.Every request is passed from source to destination via one broadcast domain to confuse the opponent and avoid them from tracking the server’s position.Allocation of SECURITY Resources accepts a safety game in a simple format as input andfinds the best coverage vector for the opponent using a Stackelberg Equilibrium(SSE)technique.A Mixed Integer Linear Programming(MILP)framework is used in the algorithm.The VM challenge is reduced by afirewall-based controlling mechanism combining behavior-based detection and signature-based virus detection.The pro-posed method is focused on detecting malware attacks effectively and providing better security for the VMs.Finally,the experimental results indicate that the pro-posed security method is efficient.It consumes minimum execution time,better false positive rate,accuracy,and memory usage than the conventional approach.展开更多
基金supported by the National Science and Technology Major Project(J2019-IV-0003-0070)the National Natural Science Foundation of China(Grant No.12102320)+1 种基金the Advanced Aviation Power Innovation Workstation Project(HKCX2019-01-003)China Postdoc-toral Science Foundation(2021M692571).
文摘Avirtual wall thicknessmethod is developed to simulate the temperature field of turbine bladeswith thermal barrier coatings(TBCs),to simplify the modeling process and improve the calculation efficiency.The results show that the virtualwall thickness method can improve themesh quality by 20%,reduce the number ofmeshes by 76.7%and save the calculation time by 35.5%,compared with the traditional real wall thickness method.The average calculation error of the two methods is between 0.21%and 0.93%.Furthermore,the temperature at the blade leading edge is the highest and the average temperature of the blade pressure surface is higher than that of the suction surface under a certain service condition.The blade surface temperature presents a high temperature at both ends and a low temperature in themiddle height when the temperature of incoming gas is uniformand constant.The thermal insulation effect of TBCs is the worst near the air film hole,and the best at the blade leading edge.According to the calculated temperature field of the substrate-coating system,the highest thermal insulation temperature of the TC layer is 172.01 K,and the thermal insulation proportions of TC,TGO and BC are 93.55%,1.54%and 4.91%,respectively.
文摘With the rapid development of China’s civil aviation industry,the teaching method of operating knowledge of flight principles has changed greatly,which creates a good implementation environment to improve the safety of civil aviation in our country.At present,the main training content of air route transport pilots in China is basic aviation theory,initial flight training,airline modification,etc.The principles of flight control are an important part of basic aviation theoretical knowledge training,which will involve a large number of flight technology training content,instructors will also be based on the pilot type.Teaching flight control theory and practical knowledge requires relatively high theoretical learning ability of students,and the learning effect of this part of theoretical knowledge will directly affect the quality of subsequent learning,but also directly affect the effectiveness of flight training.This paper focuses on the analysis of the basic concepts of flight control,studies the existing problems in the teaching of flight control principles,summarizes the teaching measures of flight control principles,aiming to provide a reference to teaching personnel.
基金Xi’an Municipal Bureau of Science and Technology,No.21YXYJ0060。
文摘Objective:To compare the efficacy of anal adenectomy with virtual hanging wire and anal fistulotomy in the treatment of low anal fistula in infants and children.Methods:60 children with low anal fistula who were admitted to our hospital from October 2021 to March 2022 and met the inclusion criteria were randomly divided into two groups of 30 cases each;the treatment group was treated with anal adenectomy and virtual hanging wire surgery,and the control group was treated with anal fistula resection.The clinical efficacy after treatment was compared.Results:The total effective rate of both groups was 96.67%and the difference between the two groups was not statistically significant(P>0.05).The postoperative pain score of the treatment group was lower than that of the control group(P<0.05).The length of hospitalization and healing time of the treatment group was lower than that of the control group(P<0.05).The anal function of the patients in both groups was normal,and there was no adverse reaction.Conclusion:Anal gland excision and virtual hanging surgery for the treatment of low anal fistula in infants and children have the advantages of mild pain,reduced length of hospitalization,short healing time,and better patient experience as compared to anal fistula excision.
基金The National Natural Science Foundation of China(No.51108081)
文摘In order to investigate the permanent deformation behavior of asphalt mixtures from discontinuity, the virtual rutting test of asphalt mixtures is developed by the discrete element method (DEM). A digital specimen generation procedure considering aggregate gradation and irregular shape is developed based on the probability theory and the Monte Carlo method. The virtual rutting test is then conducted based on the generated digital specimen. In addition, on the basis of the time-temperature superposition (TTS) principle, a calculation method is used to reduce the computation time of the virtual rutting test. The simulation results are compared with the laboratory measurements. The results show that the calculation method based on the TFS principle in the discrete element (DE) viscoelastic model can significantly reduce the computation time. The deformation law of asphalt mixtures in the virtual rutting test is similar to the laboratory measurements, and the deformation and the dynamic stability of the virtual rutting test are slightly greater than the laboratory measurements. The two-dimensional virtual rutting test can predict the permanent deformation performance of asphalt mixtures.
基金The National High Technology Research and Development Program of China(863 Program)(No.2006AA11Z110)the Researchand Innovation Foundation for Graduate Students in Jiangsu Province(No.CX07B-156Z)the Excellent Doctoral Dissertation Foundation of Southeast University
文摘In order to study fracture behaviors of asphalt mixtures, virtual tests of the two-dimensional(2D) microstructure based on the discrete element method( DEM) are designed. The virtual structure of the 2D digital specimen of asphalt mixture is generated based on a particle generation program, in which the gradation and the irregular shapes of aggregates are considered. With the 2D digital specimens, a DEM-based mixture model is established and center-point beam fracture simulation tests are conducted by the DEM. Meanwhile, a series of calibration tests are carried out in laboratory to evaluate the DEM model and validate the methods of virtual fracture tests. The test results indicate that the fracture intensity of asphalt mixtures predicted by the DEM matches very well with the intensity obtained in laboratory. It is concluded that the microstructural virtual tests can be used as a supplemental tool to evaluate fracture properties of asphalt mixtures.
基金the financial support from the National Natural Science Foundation of China (Grants 11672153, 11232008, and 11227801)
文摘Fused deposition modelling(FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method(VFM) is applied to characterize all the mechanical parameters(Q, Q, Q, Q) using the full-field strain,which is measured by digital image correlation(DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method(FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30?. Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters(Q, Q, Q, Q) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants(Q, Q, Q, Q) were determined from the test with an angle of 27?.
基金Project supported by the National Natural Science Foundation of China (No. 10172038).
文摘By virtue of the comparability between the wave superposition method and the dynamic analysis of structures, a general format for overcoming the non-uniqueness of solution induced by the wave superposition method at the eigenfrequencies of the corresponding interior problems is proposed. By adding appropriate damp to the virtual source system of the wave superposition method, the unique solutions for all wave numbers can be ensured. Based on this thought, a novel method-wave superposition method with complex radius vector is constructed. Not only is the computational time of this method approximately equal to that of the standard wave superposition method, but also the accuracy is much higher compared with other correlative methods. Finally, by taking the pulsating sphere and oscillating sphere as examples, the results of calculation show that the present method can effectively overcome the non-uniqueness problem.
基金Project(51378006) supported by National Natural Science Foundation of ChinaProject(141076) supported by Huoyingdong Foundation of the Ministry of Education of China+1 种基金Project(2242015R30027) supported by Excellent Young Teacher Program of Southeast University,ChinaProject(BK20140109) supported by the Natural Science Foundation of Jiangsu Province,China
文摘The objective of this work is to model the microstructure of asphalt mixture and build virtual test for asphalt mixture by using Particle Flow Code in three dimensions(PFC^(3D))based on three-dimensional discrete element method.A randomly generating algorithm was proposed to capture the three-dimensional irregular shape of coarse aggregate.And then,modeling algorithm and method for graded aggregates were built.Based on the combination of modeling of coarse aggregates,asphalt mastic and air voids,three-dimensional virtual sample of asphalt mixture was modeled by using PFC^(3D).Virtual tests for penetration test of aggregate and uniaxial creep test of asphalt mixture were built and conducted by using PFC^(3D).By comparison of the testing results between virtual tests and actual laboratory tests,the validity of the microstructure modeling and virtual test built in this study was verified.Additionally,compared with laboratory test,the virtual test is easier to conduct and has less variability.It is proved that microstructure modeling and virtual test based on three-dimensional discrete element method is a promising way to conduct research of asphalt mixture.
文摘A novel numerical method for eliminating the singular integral and boundary effect is processed. In the proposed method, the virtual boundaries corresponding to the numbers of the true boundary arguments are chosen to be as simple as possible. An indirect radial basis function network (IRBFN) constructed by functions resulting from the indeterminate integral is used to construct the approaching virtual source functions distributed along the virtual boundaries. By using the linear superposition method, the governing equations presented in the boundaries integral equations (BIE) can be established while the fundamental solutions to the problems are introduced. The singular value decomposition (SVD) method is used to solve the governing equations since an optimal solution in the least squares sense to the system equations is available. In addition, no elements are required, and the boundary conditions can be imposed easily because of the Kronecker delta function properties of the approaching functions. Three classical 2D elasticity problems have been examined to verify the performance of the method proposed. The results show that this method has faster convergence and higher accuracy than the conventional boundary type numerical methods.
文摘A novel polygonal finite element method (PFEM) based on partition of unity is proposed, termed the virtual node method (VNM). To test the performance of the present method, numerical examples are given for solid mechanics problems. With a polynomial form, the VNM achieves better results than those of traditional PFEMs, including the Wachspress method and the mean value method in standard patch tests. Compared with the standard triangular FEM, the VNM can achieve better accuracy. With the ability to construct shape functions on polygonal elements, the VNM provides greater flexibility in mesh generation. Therefore, several fracture problems are studied to demonstrate the potential implementation. With the advantage of the VNM, the convenient refinement and remeshing strategy are applied.
基金Sponsored by 2013 Youth Program of the "Twelfth Five-year Plan" of National Educational Information Technology Research(136241233)
文摘Based on foreign and domestic literature about teaching theories and simulation application,advantages and disadvantages of simulation teaching and other teaching methods were compared,organization forms and efficiency of simulation teaching in network environment discussed,students' learning patterns and styles summarized,and the theoretical research foundation for the simulation teaching and students' learning system in network environment established.Common problems of simulation teaching and corresponding students' learning styles were discussed,application and supervision system of simulation teaching established,students' learning styles innovated.Views and innovations of virtual simulation teaching in simulation teaching of landscape architecture were given,and the research framework sorted out as reference.
文摘Energy methods and the principle of virtual work are commonly used for obtaining solutions of boundary value problems (BVPs) and initial value problems (IVPs) associated with homogeneous, isotropic and non-homogeneous, non-isotropic matter without using (or in the absence of) the mathematical models of the BVPs and the IVPs. These methods are also used for deriving mathematical models for BVPs and IVPs associated with isotropic, homogeneous as well as non-homogeneous, non-isotropic continuous matter. In energy methods when applied to IVPs, one constructs energy functional (<i>I</i>) consisting of kinetic energy, strain energy and the potential energy of loads. The first variation of this energy functional (<em>δI</em>) set to zero is a necessary condition for an extremum of <i>I</i>. In this approach one could use <i>δI</i> = 0 directly in constructing computational processes such as the finite element method or could derive Euler’s equations (differential or partial differential equations) from <i>δI</i> = 0, which is also satisfied by a solution obtained from <i>δI</i> = 0. The Euler’s equations obtained from <i>δI</i> = 0 indeed are the mathematical model associated with the energy functional <i>I</i>. In case of BVPs we follow the same approach except in this case, the energy functional <i>I</i> consists of strain energy and the potential energy of loads. In using the principle of virtual work for BVPs and the IVPs, we can also accomplish the same as described above using energy methods. In this paper we investigate consistency and validity of the mathematical models for isotropic, homogeneous and non-isotropic, non-homogeneous continuous matter for BVPs that are derived using energy functional consisting of strain energy and the potential energy of loads. Similar investigation is also presented for IVPs using energy functional consisting of kinetic energy, strain energy and the potential energy of loads. The computational approaches for BVPs and the IVPs designed using energy functional and principle of virtual work, their consistency and validity are also investigated. Classical continuum mechanics (CCM) principles <i>i.e.</i> conservation and balance laws of CCM with consistent constitutive theories and the elements of calculus of variations are employed in the investigations presented in this paper.
基金Project supported by the Natural Science Foundation of Henan Province,China(No.0311010400).
文摘Concepts for a virtual 3D space and a hyper-sphere are proposed and the formulae for determining the computable nodes of the mesh are derived.Then a new optimization design method('Virtual Mesh Method'or V.M.M)is developed.Three examples are given,showing that the method proposed is especially suitable for the optimized design of complex structures,and that the global approximate optimal solution can be searched with remarkably reduced computational work.
文摘The virtual displacement principle of elasto-plastic damage mechanics is presented. A linear complementary method for elasto-plastic damage problem is proposed by using FEM technique. This method is applicable to solving the damage structure analysis of hardened and softened nonlinear material.
基金the NationalKey Research and Development Procedure of China (Grant 2017YFB1103900)National Natural Science Foundation of China (Grants 11672153.11232008, 11227801).
文摘Thermal barrier coatings (TBCs) are widely applied in thermal components to protect metallic components. Owing to the complex layered structure of TBCs and difficult preparation of coating, the mechanical characterization of TBCs should be of primary importance. With regard to TBCs, this study deals with the constitutive parameters identification of bi-material. Considering the complex construction and boundary of bi material, the virtual fields method (VFM) was employed in this study. A methodology based on the optimized virtual fields method combined with moire interferometry was proposed for the constitutive parameters identification of bi-material. The feasibility of this method is verified using simulated deformation fields of a two-layer material subjected to three point ben ding loading. As an application, the deformation fields of the TBC specimens were measured by moire interferometry. Then, lhe mechanical parameters of the coating were identified by the proposed method. The identification results indicate that Young's modulus of the TBC top coating is 89.91 GPa, and its Poisson's ratio is 0.23.
基金This study was supported by“the Fundamental Research Funds for the Central Universities”(Grant No.2015B37814)the Postgraduate Research and Practice Innovation Program of Jiangsu Province(Grant No.KYLX15_0489)+1 种基金the National Natural Science Foundation of China(Grant No.51679081)“the Fundamental Research Funds for the Central Universities”(Grant No.2018B48514).
文摘This paper aims to apply a virtual boundary element method(VBEM)to solve the inverse problems of three-dimensional heat conduction in orthotropic media.This method avoids the singular integrations in the conventional boundary element method,and can be treated as a potential approach for solving the inverse problems of the heat conduction owing to the boundary-only discretization and semi-analytical algorithm.When the VBEM is applied to the inverse problems,the numerical instability may occur if a virtual boundary is not properly chosen.The method encounters a highly illconditioned matrix for the larger distance between the physical boundary and the virtual boundary,and otherwise is hard to avoid the singularity of the source point.Thus,it must adopt an appropriate regularization method to deal with the ill-posed systems of inverse problems.In this study,the VBEM and different regularization techniques are combined to model the inverse problem of three-dimensional heat conduction in orthotropic media.The proper regularization techniques not only make the virtual boundary to be allocated freer,but also solve the ill-conditioned equation of the inverse problem.Numerical examples demonstrate that the proposed method is efficient,accurate and numerically stable for solving the inverse problems of three-dimensional heat conduction in orthotropic media.
基金Supported by the National Natural Science Foundation of China
文摘The virtual-ray method for treating HF electromagnetic scattering problems is derived from the plane wave of free space, and using this the plane wave scattering by an impedance wedge is studied. In the solution process a novel concept of generalized circle is introduced so that the complete amplitude function is obtained. And a reasonable physical interpretation for the term W2, which was neglected previously, is given. The calculated results agree well with those of the analytical solution obtained by G.D. Maliuzhinets(1958).
文摘In this paper, we discuss virtual element method (VEM) approximation of optimal control problem governed by Brinkman equations with control constraints. Based on the polynomial projections and variational discretization of the control variable, we build up the virtual element discrete scheme of the optimal control problem and derive the discrete first order optimality system. A priori error estimates for the state, adjoint state and control variables in L<sup>2</sup> and H<sup>1</sup> norm are derived. The theoretical findings are illustrated by the numerical experiments.
文摘Cloud computing involves remote server deployments with public net-work infrastructures that allow clients to access computational resources.Virtual Machines(VMs)are supplied on requests and launched without interactions from service providers.Intruders can target these servers and establish malicious con-nections on VMs for carrying out attacks on other clustered VMs.The existing system has issues with execution time and false-positive rates.Hence,the overall system performance is degraded considerably.The proposed approach is designed to eliminate Cross-VM side attacks and VM escape and hide the server’s position so that the opponent cannot track the target server beyond a certain point.Every request is passed from source to destination via one broadcast domain to confuse the opponent and avoid them from tracking the server’s position.Allocation of SECURITY Resources accepts a safety game in a simple format as input andfinds the best coverage vector for the opponent using a Stackelberg Equilibrium(SSE)technique.A Mixed Integer Linear Programming(MILP)framework is used in the algorithm.The VM challenge is reduced by afirewall-based controlling mechanism combining behavior-based detection and signature-based virus detection.The pro-posed method is focused on detecting malware attacks effectively and providing better security for the VMs.Finally,the experimental results indicate that the pro-posed security method is efficient.It consumes minimum execution time,better false positive rate,accuracy,and memory usage than the conventional approach.