Enhanced piezoresistivity in Ni-silicone rubber composites

This paper reports that the nickel-silicone rubber composites with enhanced piezoresistivity were synthesized with much reduced nickel concentration. A large piezosensitivity of 0.716/kPa and a gauge factor of 600 have been obtained for a composite sample with filler-polymer ratio of 2.7：1 by weight. Measurements of resistance as a function of uniaxial force reveal that the piezoresistance arises predominantly from the internal heterogeneity of the material and the effect of geometrical changes of samples under pressure is negleetably small. The nonlinear current-voltage characteristic of the composite depends strongly on the filler content, the initial compression and the electrical current flowing in the sample. Ohmic behaviour has been observed only in the highly compressed samples. The breakdown strength decreases with increasing filler content of the composite. Both I - V and R - f characteristics indicates that the resistivity of the composites decreases with electrical field, suggesting that the composite may also be used to make voltage sensitive resistors for protecting circuits. All the experimental results favour a quantum tunnelling mechanism of conductivity. It finds that the concept ＇negative resistance＇, often used to describe the phenomena that current decreases with increasing voltage, is not appropriate and should be avoided.

Coordinated control for voltage regulation of distribution network voltage regulation by distributed energy storage systems

With more and more distributed photovoltaic(PV)plants access to the distribution system,whose structure is changing and becoming an active network.The traditional methods of voltage regulation may hardly adapt to this new situation.To address this problem,this paper presents a coordinated control method of distributed energy storage systems(DESSs)for voltage regulation in a distribution network.The influence of the voltage caused by the PV plant is analyzed in a simple distribution feeder at first.The voltage regulation areas corresponding to DESSs are divided by calculating and comparing the voltage sensitivity matrix.Then,a coordinated voltage control strategy is proposed for the DESSs.Finally,the simulation results of the IEEE 33-bus radial distribution network verify the effectiveness of the proposed coordinated control method.

Millimeter wave broadband high sensitivity detectors with zero-bias Schottky diodes

Two broadband detectors at W-band and D-band are analyzed and designed with low barrier Schottky diodes. The input circuit of the detectors is realized by low and high impedance microstrip lines, and their output circuit is composed of a radio frequency （RF） bandstop filter and a tuning line for optimum reflection phase of the RF signal. S-parameters of the complete circuit are exported to a circuit simulator for voltage sensitivity analysis. For the W band detectors, the highest measured voltage sensitivity is 11800 mV/mW at 100 GHz, and the sensitivity is higher than 2000 mV/mW in 80-104 GHz. Measured tangential sensitivity （TSS） is higher than -38 dBm, and its linearity is superior than 0.99992 at 95 GHz. For the D band detector, the highest measured voltage sensitivity is 1600 mV/mW, and the typical sensitivity is 600 mV/mW in 110-170 GHz. TSS is higher than -29 dBm, and its linearity is superior than 0.99961 at 150 GHz.

Novel Planning Approach for Fast-charging Station in Integrated System

A promising way to boost popularity of electric vehicles(EVs)is to properly layout fast charging stations(FCSs)by jointly considering interactions among EV drivers,power systems and traffic network constraints.This paper proposes a novel sensitivity analysis-based FCS planning approach,which considers the voltage sensitivity of each sub-network in the distribution network and charging service availability for EV drivers in the transportation network.In addition,energy storage systems are optimally installed to provide voltage regulation service and enhance charging capacity.Simulation tests conducted on two distribution network and transportation network coupled systems validate the efficacy of the proposed approach.Moreover,comparison studies demonstrate the proposed approach outperforms a Voronoi graph and particle swarm optimization combined planning approach in terms of much higher computation efficiency.

Impact of Renewable Energy Sources on Steady-state Stability of Weak AC/DC Systems

In recent years,the penetration of renewable resources into AC power systems has increased tremendously,creating a significantly impact on the latter’s operations and stability.In this respect,it is also important to gain a basic analytical understanding of such impact on the steady-state stability of power systems with electrically weak AC/DC interconnections,but such works are not very evident in the literature.Therefore,a classical analytic model of the single and multi-infeed HVDC system which now incorporates renewable resources is proposed.Then the well-established concept of voltage sensitivity of the AC/DC interconnection is applied to analyze the impact of the renewable resources on the steady-state stability of these composite system models,as well as on the influence of system conditions and parameters.This impact is also compared with that arising from other types of shunt devices alternatively connected at the same AC/DC interconnection,therefore their relative beneficial or negative impacts will also be benchmarked.

Design of Ka-band antipodal finline mixer and detector

This paper mainly discusses the analysis and design of a finline single-ended mixer and detector. In the circuit, for the purpose of eliminating high-order resonant modes and improving transition loss, metallic via holes are implemented along the mounting edge of the substrate embedded in the split-block of the WG-finline-microstrip transition. Meanwhile, a Ka band slow-wave and bandstop filter, which represents a reactive termination, is designed for the utilization of idle frequencies and operation frequencies energy. Full-wave analysis is carded out to optimize the input matching network of the mixer and the detector circuit using lumped elements to model the nonlinear diode. The exported S-matrix of the optimized circuit is used for conversion loss and voltage sensitivity analysis. The lowest measured conversion loss is 3.52 dB at 32.2 GHz; the conversion loss is flat and less than 5.68 dB in the frequency band of 29-34 GHz. The highest measured zero-bias voltage sensitivity is 1450 mV/mW at 38.6 GHz, and the sensitivity is better than 1000 mV/mW in the frequency band of 38-40 GHz.