Transitional Recovery Voltages at Capacitive Currents Switching-off by Vacuum and SF6 Circuit-Breakers

Results of calculation the recovery voltages conditioned by capacitive currents switching-off by high voltage vacuum and auto-compression （SF6） circuit-breakers are presented in the article. The purpose of research was evaluating the maximum values of recovery voltages and also studying the dependence of recovery voltages on some influencing factors, especially on type of circuit-breaker presented in numerical models with its dielectric strength restoration law, chopping current and operation time. The research was carried out with using computer simulation.

Electromagnetic Fields and Induced Voltages on Underground Pipeline in the Vicinity of AC Traction System

Various regulations, aimed at the protection of human beings and electrical equipment against possible adverse effects resulting from exposure to electromagnetic fields, have been issued in many countries. Most of them are based on safety guidelines published by international expert groups. In this paper, electric and magnetic fields are calculated in the vicinity of 25 kV traction line supplying railway traction systems. Calculation results are compared to exposure limits specified by safety guidelines and regulations. Possible countermeasures for reduction of electromagnetic fields are proposed. Also, this paper presents a method for calculation of the induced voltages to an underground gas pipeline from a neighbouring 25 kV electric traction overhead line in case of short circuit. Calculations are performed with EMTP-ATP software. Possible countermeasures for reduction of induced voltages are proposed.

A SCHEDULING SCHEME WITH DYNAMIC FREQUENCY CLOCKING AND MULTIPLE VOLTAGES FOR LOW POWER DESIGNS

In this letter, a scheduling scheme based on Dynamic Frequency Clocking (DFC) and multiple voltages is proposed for low power designs under the timing and the resource constraints. Unlike the conventional methods at high level synthesis where only voltages of nodes were considered, the scheme based on a gain function considers both voltage and frequency simultaneously to reduce energy consumption. Experiments with a number of DSP benchmarks show that the proposed scheme achieves an effective energy reduction.

Control of Doubly Fed Induction Generator under Unbalanced Voltages for Reduction of Torque Pulsation

The unbalanced voltages cause negative effects on the doubly fed induction generator （DFIG） sucn as torque pulsation,and increased stator current. Based on the symmetrical component theory, the torque pulsation is the consequence of the interaction of stator and rotor currents of different sequences. This paper presents a control technique to reduce the effect of unbalanced voltages on the DFIG in wind energy conversion systems. The negative sequence stator voltage is derived from the unbalanced three phase stator voltages. The compensated rotor voltage in terms of the derived negative sequence stator voltage and slip which minimizes the negative stator and rotor currents is proposed. The results from the simulation of control system with steady state model and dynamic model of the DFIG show that additional control loop with compensated voltage can significantly reduce torque and reactive power pulsations.

Charging and absorption characteristics of small particulates under alternative and electrostatic voltages in an electrostatic precipitator

The charge quantity of small particulates such as PM2.5 plays a key role in the collection efficiency of an electrostatic precipitator（ESP）. Under a single electrostatic voltage, it is difficult to charge and absorb small particulates. A new method of superimposing an alternative voltage on the electrostatic voltage is provided in this paper. Characteristics of small particulates are analyzed under alternative and electrostatic voltages. It is demonstrated that an alternative voltage can significantly improve the collection efficiency in three aspects： preventing anti-corona, increasing the charge quantity of small particulates, and increasing the median particulate size by electric agglomeration. In addition, practical usage with the superposition of alternative voltage is provided, and the results are in agreement with the theoretical analysis.

Discharge characteristics of different lightning air terminals under composite voltages

Different types of lightning air terminals have been designed over the years.Concern regarding the effect of different types of air terminals,especially the early streamer emission(ESE)-type,remains controversial.This paper describes the discharge characteristics of different types of air terminals,two of which are quite similar to the ESE-type dynasphere,and concludes that the tested non-standard air terminals have discharge characteristics similar to those of Franklin rods and that their lightning protection performance should be similar.

The effect of substrate doping on the flatband and threshold voltages of a strained-Si pMOSFET

The effect of substrate doping on the flatband and threshold voltages of a strained-Si/SiGe p metal-oxide semiconductor field-effect transistor（pMOSFET） has been studied.By physically deriving the models of the flatband and threshold voltages,which have been validated by numerical simulation and experimental data,the shift in the plateau from the inversion region to the accumulation region as the substrate doping increases has been explained.The proposed model can provide a valuable reference to the designers of strained-Si devices and has been implemented in software for extracting the parameters of a strained-Si MOSFET.

Mechanism of improving forward and reverse blocking voltages in AlGaN/GaN HEMTs by using Schottky drain

In this paper, we demonstrate that a Schottky drain can improve the forward and reverse blocking voltages （BVs） simultaneously in A1GaN/GaN high-electron mobility transistors （HEMTs）. The mechanism of improving the two BVs is investigated by analysing the leakage current components and by software simulation. The forward BV increases from 72 V to 149 V due to the good Schottky contact morphology. During the reverse bias, the buffer leakage in the Ohmic- drain HEMT increases significantly with the increase of the negative drain bias. For the Schottky-drain HEMT, the buffer leakage is suppressed effectively by the formation of the depletion region at the drain terminal. As a result, the reverse BV is enhanced from -5 V to -49 V by using a Schottky drain. Experiments and the simulation indicate that a Schottky drain is desirable for power electronic applications.

A novel digital control strategy of three-phase shunt active power filter under non-ideal mains voltages

A novel control strategy for three-phase shunt active power filter (SAPF) was proposed to improve its performance under non-ideal mains voltages. The approach was inspired by our finding that the classic instantaneous reactive power theory based algorithm was unsatisfactory in terms of isolating positive sequence fundamental active components exactly under non-ideal mains voltages. So, a modified ip-iq reference current calculation method was presented. With usage of the new method, not only the positive sequence but also the fundamental active current components can be accurately isolated from load current. A deadbeat closed-loop control model is built in order to eliminate both delay error and tracking error between reference voltages and compensation voltages under unbalanced and distorted mains voltages. Computer simulation results show that the proposed strategy is effective with better tracking ability and lower total harmonic distortion (THD). The strategy is also applied to a 10 kV substation with a local electrolysis manganese plant injecting a large amount of harmonics into the power system, and is proved to be more practical and efficient.

Effect of substrate doping on threshold voltages of buried channel pMOSFET based on strained-SiGe technology

The effect of substrate doping on the threshold voltages of buried channel pMOSFET based on strained-SiGe technology was studied.By physically deriving the models of the threshold voltages,it is found that the layer which inversely occurs first is substrate doping dependent,giving explanation for the variation of plateau observed in the C-V characteristics of this device,as the doping concentration increases.The threshold voltages obtained from the proposed model are-1.2805 V for buried channel and-2.9358 V for surface channel at a lightly doping case,and-3.41 V for surface channel at a heavily doping case,which agrees well with the experimental results.Also,the variations of the threshold voltages with several device parameters are discussed,which provides valuable reference to the designers of strained-SiGe devices.

An Energy-Efficient 12b 2.56 MS/s SAR ADC Using Successive Scaling of Reference Voltages

This paper presents an energy efficient architecture for successive approximation register(SAR)analog to digital converter(ADC).SAR ADCs with a capacitor array structure have been widely used because of its simple architecture and relatively high speed.However,conventional SAR ADCs consume relatively high energy due to the large number of capacitors used in the capacitor array and their sizes scaled up along with the number of bits.The proposed architecture reduces the energy consumption as well as the capacitor size by employing a new array architecture that scales down the reference voltages instead of scaling up the capacitor sizes.The proposed 12-bit SAR ADC is implemented in Complementary Metal Oxide Semiconductor(CMOS)0.13 um library using Cadence Virtuoso design tool.Simulation results and mathematical model demonstrate the overall energy savings of up to 97.3%compared with conventional SAR ADC,67%compared with the SAR ADC with split capacitor,and 35%compared with the resistor and capacitor(R&C)Hybrid SAR ADC.The ADC achieves an effective number of bits(ENOB)of 11.27 bits and consumes 61.7 uW at sampling rate of 2.56 MS/s,offering an energy consumption of 9.8 fJ per conversion step.The proposed SAR ADC offers 95.5%reduction in chip core area compared to conventional architecture,while occupying an active area of 0.088 mm2.

The transverse laser induced thermoelectric voltages in step flow growth (1-x)Pb(Mg_(1/3)Nb_(2/3))O_(3-x)PbTiO_3 thin films

This paper reports that the transverse laser induced thermoelectric voltages （LITV） axe observed for the first time in the step flow growth （1- x）PD（Mg1/3Nb2/3）O3-xPbTiO3 （PMN-PT, x = 0.20, 0.33, 0.50） thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate （PMN） and lead titanate （PT）, there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength, the largest induced voltage is observed in the 0.50Pb（Mg1/3Nb2/3）O3-0.50 PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated.

Numerical simulation on magnetic confinement characteristics of internal vortex electrostatic cyclone precipitator under different working voltages

Aiming at improving the capture performance of internal vortex electrostatic cyclone precipitator(ECP),a theoretical model with mechanics-electric-magnetic coupling was established,the collection efficiency of magnetic confinement ECP under different working voltages was simulated,and the influence of magnetic flux intensity on the removal performance of submicron particles was explored.Results show that the number of particles escaped from the cyclone is greatly reduced after the introduction of magnetic field and electric field,indicating that charging effect and magnetic confinement are more conductive to trap submicron particles in the internal vortex ECP.The lower the working voltage is,the worse the charging lifting effect is,but the stronger the magnetic confinement characteristics are.Furthermore,the contributions of charging effect to collection efficiency and magnetic confinement characteristics are more obvious at a weaker magnetic flux density.The research results can provide a practical new idea for the innovative design of ECP.

An overview of bearing voltages and currents in rail transportation traction motors

In modern rail transportation,inverter drive systems have been extensively used due to their excellent speed control capabilities.However,in recent years,premature failure problems caused by bearing voltage and current phenomena have been frequently reported in electric motors,with electrical bearing failures making up a considerable percentage.The purpose of this review is to provide a comprehensive overview of facets relating to the electrical erosion of bearings in an electrical environment represented by railway vehicles.First,the origins of the phenomenon as well as typical bearing electrical failure modes are discussed.Next,we introduce the distinctive features of the electrical environment of railway traction motor bearings,including output voltages with high common-mode components and systems with complex grounding configurations.Then,we classify the fundamental mechanisms for generating bearing voltages/currents into four groups,and present their modeling processes,including equivalent circuit establishment and parameter determination methods.Furthermore,we summarize the strategies frequently used to protect bearings,and describe a typical solution to suppress electrical bearing failures in railway vehicles.Finally,we present a case example to illustrate a research procedure for systematic investigation of inverter-induced bearing currents in rail transportation.

Bias-Independent Inter-Modulation Method for Simultaneously Measuring Low-Frequency Modulation and Bias Half-Wave Voltages of Mach-Zehnder Modulators

A bias-independent inter-modulation method is proposed and demonstrated for measuring low-frequency modulation and bias half-wave voltages of Mach-Zehnder modulators(MZMs).The method consists of simultaneous sinusoidal modulation on the modulation and bias ports of the MZM under test.Sinusoidal-modulated sidebands heterodyne with each other and generate the desired inter-modulation products after photodetection,which allows extracting both the modulation depth and half-wave voltage for the modulation and bias ports of the MZM.Our method is independent of bias voltages of the MZM,which can be canceled out by carefully choosing the sinusoidal-modulation frequencies.Moreover,the proposed method enables the low swing voltage for measuring both the modulation depth and half-wave voltage of MZMs.Experiments indicate that the proposed method features the simple setup and high accuracy for low-frequency response measurement ranging from 1 Hz to 1 MHz.

Rationally designing electrolyte additives for highly improving cyclability of LiNi_(0.5)Mn_(1.5)O_(4)/Graphite cells

High voltage is necessary for high energy lithium-ion batteries but difficult to achieve because of the highly deteriorated cyclability of the batteries.A novel strategy is developed to extend cyclability of a high voltage lithium-ion battery,LiNi_(0.5)Mn_(1.5)O_(4)/Graphite(LNMO/Graphite)cell,which emphasizes a rational design of an electrolyte additive that can effectively construct protective interphases on anode and cathode and highly eliminate the effect of hydrogen fluoride(HF).5-Trifluoromethylpyridine-trime thyl lithium borate(LTFMP-TMB),is synthesized,featuring with multi-functionalities.Its anion TFMPTMB-tends to be enriched on cathode and can be preferentially oxidized yielding TMB and radical TFMP-.Both TMB and radical TFMP can combine HF and thus eliminate the detrimental effect of HF on cathode,while the TMB dragged on cathode thus takes a preferential oxidation and constructs a protective cathode interphase.On the other hand,LTFMP-TMB is preferentially reduced on anode and constructs a protective anode interphase.Consequently,a small amount of LTFMP-TMB(0.2%)in 1.0 M LiPF6in EC/DEC/EMC(3/2/5,wt%)results in a highly improved cyclability of LNMO/Graphite cell,with the capacity retention enhanced from 52%to 80%after 150 cycles at 0.5 C between 3.5 and 4.8 V.The as-developed strategy provides a model of designing electrolyte additives for improving cyclability of high voltage batteries.

Stable Cycling of All-Solid-State Lithium Metal Batteries Enabled by Salt Engineering of PEO-Based Polymer Electrolytes

Poly(ethylene oxide)(PEO)-based polymer electrolytes show the prospect in all-solid-state lithium metal batteries;however,they present limitations of low room-temperature ionic conductivity,and interfacial incompatibility with high voltage cathodes.Therefore,a salt engineering of 1,1,2,2,3,3-hexafluoropropane-1,3-disulfonimide lithium salt(LiHFDF)/LiTFSI system was developed in PEO-based electrolyte,demonstrating to effectively regulate Li ion transport and improve the interfacial stability under high voltage.We show,by manipulating the interaction between PEO matrix and TFSI^(-)-HFDF^(-),the optimized solid-state polymer electrolyte achieves maximum Li+conduction of 1.24×10^(-4)S cm^(-1)at 40℃,which is almost 3 times of the baseline.Also,the optimized polymer electrolyte demonstrates outstanding stable cycling in the LiFePO_(4)/Li and LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2)/Li(3.0-4.4 V,200 cycles)based all-solid-state lithium batteries at 40℃.

11.2 W/mm power density AlGaN/GaN high electron-mobility transistors on a GaN substrate

In this letter,high power density AlGaN/GaN high electron-mobility transistors(HEMTs)on a freestanding GaN substrate are reported.An asymmetricΓ-shaped 500-nm gate with a field plate of 650 nm is introduced to improve microwave power performance.The breakdown voltage(BV)is increased to more than 200 V for the fabricated device with gate-to-source and gate-to-drain distances of 1.08 and 2.92μm.A record continuous-wave power density of 11.2 W/mm@10 GHz is realized with a drain bias of 70 V.The maximum oscillation frequency(f_(max))and unity current gain cut-off frequency(f_(t))of the AlGaN/GaN HEMTs exceed 30 and 20 GHz,respectively.The results demonstrate the potential of AlGaN/GaN HEMTs on freestanding GaN substrates for microwave power applications.

Effects of Hybrid Voltages on Oxide Formation on 6061 Al-alloys During Plasma Electrolytic Oxidation

Plasma electrolytic oxidation （PEO） is carried out on 6061 Al-alloys in a weak alkaline electrolyte containing NaOH, Na2SiO3 and NaCl. Centered on the correlation of composition and structure, analyses by means of X-ray diffration （XRD）, scanning electron microscope （SEM） and energy dispersive spectrometry （EDS） are conducted on the specimens, which have been PEO-treated under hybrid voltages of different direct current （DC） values （140-280 V） with constant alternate current （AC） amplitude （200 V）. Attention is paid to the composition, properties and growth mechanism of oxide layers formed with hybrid voltages. Moreover, the main effects of DC value are discussed. Ceramic layers with a double-layer structure which combines hard outer and soft inner layers are found to be consist of α-Al2O3,γ-Al2O3 and mullite. With the DC values increasing, the growth of the ceramic layers tends to have increasingly obvious three-stage feature.

Understanding the correlation between energy-state mismatching and open-circuit voltage loss in bulk heterojunction solar cells

Photoinduced intermolecular charge transfer(PICT)determines the voltage loss in bulk heterojunction(BHJ)organic photovoltaics(OPVs),and this voltage loss can be minimized by inducing efficient PICT,which requires energy-state matching between the donor and acceptor at the BHJ interfaces.Thus,both geometrically and energetically accessible delocalized state matching at the hot energy level is crucial for achieving efficient PICT.In this study,an effective method for quantifying the hot state matching of OPVs was developed.The degree of energy-state matching between the electron donor and acceptor at BHJ interfaces was quantified using a mismatching factor(MF)calculated from the modified optical density of the BHJ.Furthermore,the correlation between the open-circuit voltage(Voc)of the OPV device and energy-state matching at the BHJ interface was investigated using the calculated MF.The OPVs with small absolute MF values exhibited high Voc values.This result clearly indicates that the energy-state matching between the donor and acceptor is crucial for achieving a high Voc in OPVs.Because the MF indicates the degree of energy-state matching,which is a critical factor for suppressing energy loss,it can be used to estimate the Voc loss in OPVs.