The effects of different contents of a MgO expansive agent and phosphorus slag on the mechanical properties,shrinkage behavior,and the heat of hydration of concrete were studied.The slump flow,setting time,dry shrinka...The effects of different contents of a MgO expansive agent and phosphorus slag on the mechanical properties,shrinkage behavior,and the heat of hydration of concrete were studied.The slump flow,setting time,dry shrinkage,and hydration heat were used as sensitive parameters to assess the response of the considered specimens.As shown by the results,in general,with an increase in the phosphorus slag content,the hydration heat of concrete decreases for all ages,but the early strength displays a downward trend and the dry shrinkage rate increases.The 90-d strength and dry shrinkage of concrete could be improved with a phosphorus residue content between 0%-20%,with the best performances in terms of mechanical properties and shrinkage characteristics being achieved for a content of 20 kg/m^(3).On the basis of these results,it can be concluded that appropriate amounts of phosphorus slag and MgO expansive agent can be used to improve the compressive strength of concrete in the later stage by reducing the hydration heat and dry shrinkage rate,respectively.展开更多
The crystallization has significant influence on fluidity of slag and slag discharge of entrained-flow-bed(EFB) gasifier. The crystallization characteristics and fluidity of five synthetic slags with different MgO/CaO...The crystallization has significant influence on fluidity of slag and slag discharge of entrained-flow-bed(EFB) gasifier. The crystallization characteristics and fluidity of five synthetic slags with different MgO/CaO ratios prepared on the basis of the range of oxide contents of Zhundong coal ash were investigated in this study. The results show that with the MgO/CaO ratio increase, the initial crystallization temperature increases, and the main temperature range of crystallization ratio growth moves to higher temperature range gradually which causes Tp25(Tp25is the temperature corresponding to the viscosity of 25 Pa·s)to increase. Mg-rich crystals are formed preferentially than Ca-rich crystals when adding the same amount of MgO and CaO during cooling. The effective slagging operating temperature range decrease from 217 ℃ for the slag with a 0:4 MgO/CaO ratio to 44 ℃ for the slag with a 4:0 MgO/CaO ratio with the MgO/CaO ratio increase. The slags with 2:2 and 1:3 MgO/CaO ratios show similar effective slagging operating temperature range, Tp25and the temperature corresponding to the viscosity of 2 Pa·s.However, compared with the slag with a 1:3 MgO/CaO ratio, the crystallization ratio and rate of slag with a 2:2 MgO/CaO ratio are lower within lower temperature range(1300–1200 ℃), causing its lower critical viscosity temperature and wider actual operating temperature range. Of the five slags, the widest effective slagging operating temperature range and the lowest Tp25of the slag with a 0:4 MgO/CaO ratio due to its low crystallization ratio, and wider actual operating temperature range of the slag with a 2:2 MgO/CaO ratio make the two slags suitable for slag discharge of EFB gasifier.展开更多
Wetting phenomena between MgO C and CaO SiO2 slags were investigated by varying carbon content.A sessile drop technique was adopted to study the wetting phenomena in conjunction with a high speed camera for the observ...Wetting phenomena between MgO C and CaO SiO2 slags were investigated by varying carbon content.A sessile drop technique was adopted to study the wetting phenomena in conjunction with a high speed camera for the observation of intrinsic wetting phenomena.The results show that the high content of SiO2 and the presence of Al2O3 in slags enhance the diffusion of Mg2+,leading to the promotion of reactive wetting.The carbon in MgO C refractory impedes the penetration of slags by repelling the slag and slowing the diffusion of Mg2+.This accounts for the non-wetting behavior of the slag on MgO C refractory with 17% (mass fraction) carbon similar to that of graphite.展开更多
Magnesiu-Calcia materials containing 22 -53 wt% CaO hare been investigated Jot refinery slag corrosion and penetration resistance by Scanning Electron Microscopy （ SEM） .nd XRD. The corrosion and penetration resista...Magnesiu-Calcia materials containing 22 -53 wt% CaO hare been investigated Jot refinery slag corrosion and penetration resistance by Scanning Electron Microscopy （ SEM） .nd XRD. The corrosion and penetration resistance of MgO-CaO materials is enhanced with the increase of CaO content in specimens. It can be explained that, with increase of CaO content, the specimens reacted will＋ slag form higher melting point minerals of C3S ant C2S, creating a dense surface layer, which stopped others from penetrating further. Thus , the corrosion and penetration resistame was improved. No matter what kinds of slag were chosen, the depth of penetration decreased will＋ increase of CaO con,tent.展开更多
The liquid iron containing elements Nb,Mn and Si has been equilibrated with MgO-SiO_2-MnO slag melts at 1600℃ in a Mo wire-wound resistance furnace with a duration of 4h.The oxygen activities in liquid iron were meas...The liquid iron containing elements Nb,Mn and Si has been equilibrated with MgO-SiO_2-MnO slag melts at 1600℃ in a Mo wire-wound resistance furnace with a duration of 4h.The oxygen activities in liquid iron were measured with oxygen sensors.Using the known equilibrium constants of concerning reactions and the oxygen activities in liquid iron,the activities of components in the slag melts can be calculated.It was found that the par- tition ratios of Nb.Mn and Si have a close linear relationship with α_(FeO) in logarithmic scale.The dependence of Nb partition ratio on mole fractions of the slag components was al- so obtained.展开更多
To provide theoretical guidance for performance stability control of low-reactive mold fluxes,the effects of BaO and MgO on the structure and properties of aluminate slag with various CaO/Al_(2)0_(3)(C/A)ratios were i...To provide theoretical guidance for performance stability control of low-reactive mold fluxes,the effects of BaO and MgO on the structure and properties of aluminate slag with various CaO/Al_(2)0_(3)(C/A)ratios were investigated using the Fourier transform infrared spectrometer,Raman spectroscope,hemispherical melting point instrument,rotational viscometer and X-ray diffractometer.The results indicated that with BaO and MgO addition,the structure polymerization was first weakened and then enhanced at C/A of 1.1,and the transition contents corresponded to 8 wt.%BaO and 2 wt.%MgO,respectively,while the structure polymerization decreased continuously at C/A of 1.3.Since the viscosity change was well consistent with the structure evolution,the polymerization degree played a more prominent role in the slag viscosity than superheat degree when the melting temperature difference was within 40℃.The break temperature decreased initially and then increased with augment of BaO and MgO at C/A of 1.1,while it manifested a decrease trend with BaO addition,and it decreased obviously but then turned to increase with MgO increment at C/A of 1.3.The crystallization phase and crystallization ratio kept stable with BaO increment,while the crystallization ratio rose greatly with MgO promoting LiAlO_(2)precipitation at C/A of 1.1.The crystal types of all experimental slags were mainly Ca_(12)Al_(14)O_(33)and CaF_(2)at C/A of 1.3,and the precipitation of crystalline phase BaAl2O4 demonstrated a rising trend,while that of Ca_(12)Al_(14)O_(33)gradually declined with BaO augment.展开更多
Activities of FeO in CaO-SiO2-Al2O3-MgO-FeO slags were determined at 1673 K by electrochemical of the solid electrolyte cell： Mo [Mo＋MoOu[ZrO2（MgO）[Fe＋（CaO-SiO2-Al2O3-MgO-FeO）＋Ag[Fe. The influences of slag com...Activities of FeO in CaO-SiO2-Al2O3-MgO-FeO slags were determined at 1673 K by electrochemical of the solid electrolyte cell： Mo [Mo＋MoOu[ZrO2（MgO）[Fe＋（CaO-SiO2-Al2O3-MgO-FeO）＋Ag[Fe. The influences of slag compositions and basicity on FeO activities were analyzed. The results reveal that, for slags of fixed （%CaO）/（%SiO2） ratio, MgO and Al2O3 content, there was an increase of FeO activities with increase of FeO content. For slags with constant {（%CaO）＋ （%MgO）}/（%SiO2） ratio, fixed FeO and A1203 content, FeO activities decreased when MgO content increased from 5% to 10%, and increased with the increase of MgO content when it was over 10%. The FeO activities increased when （%CaO）/（%SiO2） ratio changed from 1.03 to 1.30 in the slags of constant MgO, FeO and Al2O3 content.展开更多
The sulphide capacity of CaO-SiO2-Al2O3-MgO-FetO slags was studied at 1773 K using gas-slag equilibrium techniques. Utilizing a Pt crucible, the slag was equilibrated with a mixture of gases, namely, CO, CO2, SO2 and ...The sulphide capacity of CaO-SiO2-Al2O3-MgO-FetO slags was studied at 1773 K using gas-slag equilibrium techniques. Utilizing a Pt crucible, the slag was equilibrated with a mixture of gases, namely, CO, CO2, SO2 and N2 to provide the partial pressure of oxygen and sulphur. It was shown that at fixed FetO and Al2O3 contents and a fixed { （%CaO）＋（%MgO）}/（%SIO2） ratio, the sulphide capacity decreases with increasing MgO content. At a constant （%CaO）/（%SiO2） ratio and constant MgO and Al2O3 contents, increasing the FetO content of the slags also results in an increase of the sulphide capacity. The rising basicity of （%CaO）/（%SiO2） from 1.0 to 1.4 at fixed MgO, FetO and Al2O3 contents significantly increases the sulphide capacity.展开更多
Surface tension of calcium aluminate refining slag was measured by the Slide method at 1823 K.Based on different levels of the MgO content and the mass ratio of CaO to Al_2O_3,the effects of MgO content and the mass r...Surface tension of calcium aluminate refining slag was measured by the Slide method at 1823 K.Based on different levels of the MgO content and the mass ratio of CaO to Al_2O_3,the effects of MgO content and the mass ratio of CaO to Al_2O_3 on surface tension were investigated.The results indicate that surface tension decreased with increasing MgO content(from 0 to 4.86%),followed by an increase with further increasing MgO content up to 11.33%.The trend that surface tension changed with the mass ratio of CaO to Al_2O_3 was the same as the trend that surface tension changed with the MgO content.The surface tension was varied from 0.617 N/m to 0.710 N/m,for the mass ratio of CaO to Al_2O_3 varying between 0.60 and 1.28.An attempt was made to estimate surface tension of CaO-Al_2O_3-MgO slag and its sub-system,and the application showed that the model worked well.展开更多
基金supported by CSCEC Technology Research and Development Plan(CSCEC-2020-Z-39).
文摘The effects of different contents of a MgO expansive agent and phosphorus slag on the mechanical properties,shrinkage behavior,and the heat of hydration of concrete were studied.The slump flow,setting time,dry shrinkage,and hydration heat were used as sensitive parameters to assess the response of the considered specimens.As shown by the results,in general,with an increase in the phosphorus slag content,the hydration heat of concrete decreases for all ages,but the early strength displays a downward trend and the dry shrinkage rate increases.The 90-d strength and dry shrinkage of concrete could be improved with a phosphorus residue content between 0%-20%,with the best performances in terms of mechanical properties and shrinkage characteristics being achieved for a content of 20 kg/m^(3).On the basis of these results,it can be concluded that appropriate amounts of phosphorus slag and MgO expansive agent can be used to improve the compressive strength of concrete in the later stage by reducing the hydration heat and dry shrinkage rate,respectively.
基金supported by the National Natural Science Foundation of China(21878082).
文摘The crystallization has significant influence on fluidity of slag and slag discharge of entrained-flow-bed(EFB) gasifier. The crystallization characteristics and fluidity of five synthetic slags with different MgO/CaO ratios prepared on the basis of the range of oxide contents of Zhundong coal ash were investigated in this study. The results show that with the MgO/CaO ratio increase, the initial crystallization temperature increases, and the main temperature range of crystallization ratio growth moves to higher temperature range gradually which causes Tp25(Tp25is the temperature corresponding to the viscosity of 25 Pa·s)to increase. Mg-rich crystals are formed preferentially than Ca-rich crystals when adding the same amount of MgO and CaO during cooling. The effective slagging operating temperature range decrease from 217 ℃ for the slag with a 0:4 MgO/CaO ratio to 44 ℃ for the slag with a 4:0 MgO/CaO ratio with the MgO/CaO ratio increase. The slags with 2:2 and 1:3 MgO/CaO ratios show similar effective slagging operating temperature range, Tp25and the temperature corresponding to the viscosity of 2 Pa·s.However, compared with the slag with a 1:3 MgO/CaO ratio, the crystallization ratio and rate of slag with a 2:2 MgO/CaO ratio are lower within lower temperature range(1300–1200 ℃), causing its lower critical viscosity temperature and wider actual operating temperature range. Of the five slags, the widest effective slagging operating temperature range and the lowest Tp25of the slag with a 0:4 MgO/CaO ratio due to its low crystallization ratio, and wider actual operating temperature range of the slag with a 2:2 MgO/CaO ratio make the two slags suitable for slag discharge of EFB gasifier.
基金supported by the R&D Center for Valuable Recycling(Global-Top Environmental Technology Development Program)funded by the Ministry of Environment(Project No.:11-C22-ID)
文摘Wetting phenomena between MgO C and CaO SiO2 slags were investigated by varying carbon content.A sessile drop technique was adopted to study the wetting phenomena in conjunction with a high speed camera for the observation of intrinsic wetting phenomena.The results show that the high content of SiO2 and the presence of Al2O3 in slags enhance the diffusion of Mg2+,leading to the promotion of reactive wetting.The carbon in MgO C refractory impedes the penetration of slags by repelling the slag and slowing the diffusion of Mg2+.This accounts for the non-wetting behavior of the slag on MgO C refractory with 17% (mass fraction) carbon similar to that of graphite.
文摘Magnesiu-Calcia materials containing 22 -53 wt% CaO hare been investigated Jot refinery slag corrosion and penetration resistance by Scanning Electron Microscopy （ SEM） .nd XRD. The corrosion and penetration resistance of MgO-CaO materials is enhanced with the increase of CaO content in specimens. It can be explained that, with increase of CaO content, the specimens reacted will＋ slag form higher melting point minerals of C3S ant C2S, creating a dense surface layer, which stopped others from penetrating further. Thus , the corrosion and penetration resistame was improved. No matter what kinds of slag were chosen, the depth of penetration decreased will＋ increase of CaO con,tent.
文摘The liquid iron containing elements Nb,Mn and Si has been equilibrated with MgO-SiO_2-MnO slag melts at 1600℃ in a Mo wire-wound resistance furnace with a duration of 4h.The oxygen activities in liquid iron were measured with oxygen sensors.Using the known equilibrium constants of concerning reactions and the oxygen activities in liquid iron,the activities of components in the slag melts can be calculated.It was found that the par- tition ratios of Nb.Mn and Si have a close linear relationship with α_(FeO) in logarithmic scale.The dependence of Nb partition ratio on mole fractions of the slag components was al- so obtained.
基金The authors would like to deeply appreciate the fund support from the Natural Science Foundation of Anhui Provincial Education Department(KJ2021A0358)the National Natural Science Foundation of China(51804004)。
文摘To provide theoretical guidance for performance stability control of low-reactive mold fluxes,the effects of BaO and MgO on the structure and properties of aluminate slag with various CaO/Al_(2)0_(3)(C/A)ratios were investigated using the Fourier transform infrared spectrometer,Raman spectroscope,hemispherical melting point instrument,rotational viscometer and X-ray diffractometer.The results indicated that with BaO and MgO addition,the structure polymerization was first weakened and then enhanced at C/A of 1.1,and the transition contents corresponded to 8 wt.%BaO and 2 wt.%MgO,respectively,while the structure polymerization decreased continuously at C/A of 1.3.Since the viscosity change was well consistent with the structure evolution,the polymerization degree played a more prominent role in the slag viscosity than superheat degree when the melting temperature difference was within 40℃.The break temperature decreased initially and then increased with augment of BaO and MgO at C/A of 1.1,while it manifested a decrease trend with BaO addition,and it decreased obviously but then turned to increase with MgO increment at C/A of 1.3.The crystallization phase and crystallization ratio kept stable with BaO increment,while the crystallization ratio rose greatly with MgO promoting LiAlO_(2)precipitation at C/A of 1.1.The crystal types of all experimental slags were mainly Ca_(12)Al_(14)O_(33)and CaF_(2)at C/A of 1.3,and the precipitation of crystalline phase BaAl2O4 demonstrated a rising trend,while that of Ca_(12)Al_(14)O_(33)gradually declined with BaO augment.
基金Project supported by the National Natural Science Foundation of China （Grant No.50574036）
文摘Activities of FeO in CaO-SiO2-Al2O3-MgO-FeO slags were determined at 1673 K by electrochemical of the solid electrolyte cell： Mo [Mo＋MoOu[ZrO2（MgO）[Fe＋（CaO-SiO2-Al2O3-MgO-FeO）＋Ag[Fe. The influences of slag compositions and basicity on FeO activities were analyzed. The results reveal that, for slags of fixed （%CaO）/（%SiO2） ratio, MgO and Al2O3 content, there was an increase of FeO activities with increase of FeO content. For slags with constant {（%CaO）＋ （%MgO）}/（%SiO2） ratio, fixed FeO and A1203 content, FeO activities decreased when MgO content increased from 5% to 10%, and increased with the increase of MgO content when it was over 10%. The FeO activities increased when （%CaO）/（%SiO2） ratio changed from 1.03 to 1.30 in the slags of constant MgO, FeO and Al2O3 content.
基金This project was financially supported by the National Natural Science Foundation of China (No.50574036) and Natural Science Foun-dation of HeBei Province, China (No.502267).
文摘The sulphide capacity of CaO-SiO2-Al2O3-MgO-FetO slags was studied at 1773 K using gas-slag equilibrium techniques. Utilizing a Pt crucible, the slag was equilibrated with a mixture of gases, namely, CO, CO2, SO2 and N2 to provide the partial pressure of oxygen and sulphur. It was shown that at fixed FetO and Al2O3 contents and a fixed { （%CaO）＋（%MgO）}/（%SIO2） ratio, the sulphide capacity decreases with increasing MgO content. At a constant （%CaO）/（%SiO2） ratio and constant MgO and Al2O3 contents, increasing the FetO content of the slags also results in an increase of the sulphide capacity. The rising basicity of （%CaO）/（%SiO2） from 1.0 to 1.4 at fixed MgO, FetO and Al2O3 contents significantly increases the sulphide capacity.
基金Project(51204115)supported by the National Natural Science Foundation of ChinaProject(BK20130308)supported by the Basic Research Program of Jiangsu Province,ChinaProject(2014M561710)supported by China Postdoctoral Science Foundation
文摘Surface tension of calcium aluminate refining slag was measured by the Slide method at 1823 K.Based on different levels of the MgO content and the mass ratio of CaO to Al_2O_3,the effects of MgO content and the mass ratio of CaO to Al_2O_3 on surface tension were investigated.The results indicate that surface tension decreased with increasing MgO content(from 0 to 4.86%),followed by an increase with further increasing MgO content up to 11.33%.The trend that surface tension changed with the mass ratio of CaO to Al_2O_3 was the same as the trend that surface tension changed with the MgO content.The surface tension was varied from 0.617 N/m to 0.710 N/m,for the mass ratio of CaO to Al_2O_3 varying between 0.60 and 1.28.An attempt was made to estimate surface tension of CaO-Al_2O_3-MgO slag and its sub-system,and the application showed that the model worked well.
