Exfoliation corrosion behavior of 7050-T6 aluminum alloy treated with various quench transfer time

The exfoliation corrosion （EFC） behavior of 7050-T6 aluminum alloy treated with various quench transfer time after solution heat treatment was investigated by standard EFC immersion tests, strength loss measurements after EFC tests and electrochemical impedance spectroscope （EIS） technique. The results showed that EFC resistance of the alloy decreased with increasing quench transfer time. Backscattered electron scanning electron microscope （SEM） together with transmission electron microscope （TEM） observations revealed that the coverage ratio and microstructure of precipitates at grain boundary area are the most important factors which influence the EFC susceptibility of the alloy, while precipitate-free zone （PFZ） near grain boundary has no or only a minor effect on it. In addition, galvanostatic measurements of the alloy present a good correlation between EFC resistance and transients in potential. The cumulated number of transients in potential can be used to evaluate EFC resistance of the alloy.

Effects of in Vitro Maturation Time of Oocytes on Sheep Nuclear Transfer Efficiency

[Objective] The study aimed to provide references for the time of oocyte maturation in vitro and enucleation in the course of sheep nuclear transfer(NT).[Method] Compared the effects of different maturation time of oocytes on enucleation efficiency and reconstructed embryo development by means of blind enucleation and fluorescence microscopy.[Result] Treatment of IVM(in vitro maturation)19-21 h was significantly higher than IVM 16-18 h treatment in oocyte maturation rate(P<0.05)and was significantly higher than IVM 22-24 h treatment in enucleation rate(P<0.05).Three treatments had no significant difference in cleavage rate and blastocyst rate(P>0.05),but IVM 19-21 h treatment was significantly higher than the other 2 treatments in average cell number of blastocysts(P<0.05).[Conclusion] The appropriate in vitro maturation time of oocytes was 19-21 h for sheep nuclear transfer,which could significantly improve the quality of blastocysts according to the cell number per blastocyst(P<0.05).

HEURISTIC STUDY OF FLOWSHOP SCHEDULING TO MINIMIZE MEAN FLOW TIME WITH LOT TRANSFER CONSIDERED

Lot scheduling problem with idle time transfer between processes to minimize mean flow time is very important because to minimize mean flow time is to minimize work in process. But the problem is NP hard and no polynomial algorithm exists to guarantee optimal solution. Based the analysis the mathematical structure of the problem, the paper presents a new heuristic algorithm. Computer simulation shows that the proposed heuristic algorithm performs well in terms of both quality of solution and execution speed.

Discrete time transfer matrix method for dynamics of multibody system with flexible beams moving in space

In this paper, by defining new state vectors and developing new transfer matrices of various elements mov- ing in space, the discrete time transfer matrix method of multi-rigid-flexible-body system is expanded to study the dynamics of multibody system with flexible beams moving in space. Formulations and numerical example of a rigid- flexible-body three pendulums system moving in space are given to validate the method. Using the new method to study the dynamics of multi-rigid-flexible-body system mov- ing in space, the global dynamics equations of system are not needed, the orders of involved matrices of the system are very low and the computational speed is high, irrespec- tive of the size of the system. The new method is simple, straightforward, practical, and provides a powerful tool for multi-rigid-flexible-body system dynamics.

Numerical Prediction Methods for Clock Deviation Based on Two-Way Satellite Time and Frequency Transfer Data

Three functional models, polynomial, spectral analysis, and modified AR model, are studied and compared in fitting and predicting clock deviation based on the data sequence derived from two-way satellite time and frequency transfer. A robust equivalent weight is applied, which controls the significant influence of outlying observations. Some conclusions show that the prediction precision of robust estimation is better than that of LS. The prediction precision calculated from smoothed observations is higher than that calculated from sampling observations. As a count of the obvious period variations in the clock deviation sequence, the predicted values of polynomial model are implausible. The prediction precision of spectral analysis model is very low, but the principal periods can be determined. The prediction RMS of 6-hour extrapolation interval is Ins or so, when modified AR model is used.

Time Optimization of Multiple Knowledge Transfers in the Big Data Environment

In the big data environment, enterprises must constantly assimilate big dataknowledge and private knowledge by multiple knowledge transfers to maintain theircompetitive advantage. The optimal time of knowledge transfer is one of the mostimportant aspects to improve knowledge transfer efficiency. Based on the analysis of thecomplex characteristics of knowledge transfer in the big data environment, multipleknowledge transfers can be divided into two categories. One is the simultaneous transferof various types of knowledge, and the other one is multiple knowledge transfers atdifferent time points. Taking into consideration the influential factors, such as theknowledge type, knowledge structure, knowledge absorptive capacity, knowledge updaterate, discount rate, market share, profit contributions of each type of knowledge, transfercosts, product life cycle and so on, time optimization models of multiple knowledgetransfers in the big data environment are presented by maximizing the total discountedexpected profits (DEPs) of an enterprise. Some simulation experiments have beenperformed to verify the validity of the models, and the models can help enterprisesdetermine the optimal time of multiple knowledge transfer in the big data environment.

Influence of quench transfer time on microstructure and mechanical properties of 7055 aluminum alloy

The influence of quench transfer time on the microstructure and mechanical properties of 7055 aluminum alloy with and without zirconium was investigated by tensile properties test,optical microscopy,scanning electron microscopy and transmission electron microscopy.For the Zr-free alloy,the strength increases to the highest value at 20 s with transfer time,and then decreases slightly.The elongation decreases slowly with transfer time within 20 s,and more rapidly after 20 s.For the Zr-containing alloy,prolonging transfer time within 20 s results in slight decrease in the strength and elongation,and rapid drop of which is observed after 20 s.For the Zr-free alloy,prolonging transfer time can increase the percentage of intergranular fracture,which is mainly caused by wide grain boundary precipitate free zone.The failure mode of the Zr-containing alloy is modified from the predominant transgranular void growth and intergranular fracture to transgranular shear and intergranular fracture with increase in the transfer time,which is attributed to the wider grain boundary precipitate free zone and coarse equilibrium η phases in the matrix.

Joint transfer of time and frequency signals and multi-point synchronization via fiber network

A system of jointly transferring time signals with a rate of 1 pulse per second （PPS） and frequency signals of 10 MHz via a dense wavelength division multiplex-based （DWDM） fiber is demonstrated in this paper. The noises of the fiber links are suppressed and compensated for by a controlled fiber delay line. A method of calibrating and characterizing time is described. The 1PPS is synchronized by feed-forward calibrating the fiber delays precisely. The system is experimen- tally examined via a 110 km spooled fiber in laboratory. The frequency stabilities of the user end with compensation are 1.8x 10-14 at 1 s and 2.0x 10-17 at 104 s average time. The calculated uncertainty of time synchronization is 13.1 ps, whereas the direct measurement of the uncertainty is 12 ps. Next, the frequency and 1PPS are transferred via a metropoli- tan area optical fiber network from one central site to two remote sites with distances of 14 km and 110 km. The frequency stabilities of 14 km link reach 3.0x 10-14 averaged in 1 s and 1.4x 10-17 in 104 s respectively; and the stabilities of 110 km link are 8.3 x 10-14 and 1.7 x 10-17, respectively. The accuracies of synchronization are estimated to be 12.3 ps for the 14 km link and 13.1 ps for the 110 km link, respectively.

Data Transfer Over the Internet for Real Time Applications

Efficient real time data exchange over the Internet plays a crucial role in the successful application of web-based systems. In this paper, a data transfer mechanism over the Internet is proposed for real time web based applications. The mechanism incorporates the eXtensible Markup Language （XML） and Hierarchical Data Format （HDF） to provide a flexible and efficient data format. Heterogeneous transfer data is classified into light and heavy data, which are stored using XML and HDF respectively; the HDF data format is then mapped to Java Document Object Model （JDOM） objects in XML in the Java environment. These JDOM data objects are sent across computer networks with the support of the Java Remote Method Invocation （RMI） data transfer infrastructure. Client＇s defined data priority levels are implemented in RMI, which guides a server to transfer data objects at different priorities. A remote monitoring system for an industrial reactor process simulator is used as a case study to illustrate the proposed data transfer mechanism.

Application of Geodetic Receivers to Timing and Time Transfer

Two methods for smoothing pseudorange observable by Carrier and Doppler are discussed. Then the procedure based on the RINEX observation files is tested using the Ashtech Z-XII3T geodetic receivers driven by a stable external frequency at UNSO. This paper proposes to adapt this procedure for the links between geodetic receivers, in order to take advantage of the P codes available on L 1 and L 2. This new procedure uses the 30-second RINEX observations files, the standard of the International GPS Service (IGS), and processes the ionosphere-free combination of the codes P 1 and P 2; the satellite positions are deduced from the IGS rapid orbits, available after two days.

Inter-hospital transfers and door-to-balloon times for STEMI: a single centre cohort study

Background Key performance indices such as door-to-balloon times have long been recognized as quality metrics in reducing time to care for patients with acute coronary syndromes(ACS). In the situation where patients do not present to a facility capable of 24/7 percutaneous coronary interventions(PCI) delays in time to therapy can exceed the recommendation of 90 min or less. This study aimed to evaluate the impact of transfers on performance indices for patients diagnosed with ST-segment elevation myocardial infarction(STEMI). Methods Over a seven month collection period, all patients presenting with symptoms suggestive of ACS and admitted for PCI were studied. Patients were divided into dichotomous groups of direct presentations or transfers from a secondary non-PCI capable hospital with key times recorded, including symptom-onset, first hospital and PCI-capable hospital arrival and balloon inflation times to evaluate time of treatment for STEMI patients. Results Of the 87 patients diagnosed with STEMI, transferred patients experienced statistically significant delays in symptom-onset to the PCI-capable hospital(PCI-H) arrival(215 vs. 95 min, P < 0.001), symptom-onset to balloon inflation(225 vs. 160 min, P = 0.009) and first hospital arrival to balloon inflation times(106 vs. 56 min, P < 0.001). Only 28%(n = 9) of transferred patients underwent balloon inflation within 90 min from first hospital arrival, while 60%(n = 19) did within 120 min, although all received balloon inflation within 90 min from arrival at the PCI-H. After controlling for confounding factors of socio-economic status, presentation date/time and diagnostic category, transferred patients experienced an average 162% longer delays from symptom-onset to PCI-H door arrival, and 98% longer delays in symptom-onset to balloon inflation;compared to patients who present directly to the PCI-H. No statistically significant differences were noted between transferred and direct patients when measured from PCI-H door-to-balloon times. Conclusions This study shows that transferred patients experience a greater overall system delay, compared to patients who present directly for PCI, significantly increasing their time to treatment and therefore infarct times. Despite the majority of transfers experiencing pre-hospital activation, their treatment hospital arrival to balloon times are no less than direct presenters after controlling for confounding factors, further compounding the overall delay to therapy.

New research trends on high-precision time transfer technology

High-precision time transfer plays an important role in the areas of fundamental research and applications. Accompanying w ith the remarkable improvements in the ability of generating and measuring high-accuracy time-frequency signal,seeking for new time-transfer techniques betw een distant clocks w ith much further improved accuracy attracts attentions w orld-w idely. The time-transfer technique based on optical pulses has the highest precision presently,and the further improvement in the accuracy is heavily dependent on the time-domain properties of the pulse as w ell as the sensitivity of the applied measurement on the exchanged pulse. The application of optical frequency comb in time transfer for a precision up to femtosecond level are currently the focus of much interest,and has recently achieved many breakthroughs. Further investigations show that,utilizing quantum techniques,i.e. quantum measurement technique and quantum optical pulse source,can lead to a new limit on the measured timing information. Furthermore,it can be immune from atmospheric parameters,such as pressure,temperature,humidity and so on.Such quantum improvements on time-transfer have a bright prospect in the future applications requiring extremely high-accuracy timing and ranging. The potential achievements w ill form a technical basis for the future realization of sub-femtosecond time transfer system.

SOLVING 2-D NONLINEAR COUPLED HEAT AND MOISTURE TRANSFER PROBLEMS VIA A SELF-ADAPTIVE PRECISE ALGORITHM IN TIME DOMAIN

A self-adaptive precise algorithm in the time domain was employed to solve 2-D nonlinear coupled heat and moisture transfer problems. By expanding variables at a discretized time interval, the variations of variables can be described more precisely,and a nonlinear coupled initial and boundary value problem was converted into a series of recurrent linear boundary value problems which are solved by FE technique. In the computation, no additional assumption and the nonlinear iteration are required, and a criterion for self-adaptive computation is proposed to maintain sufficient computing accuracy for the change sizes of time steps. In the numerical comparison, the variations of material properties with temperature, moisture content, and both temperature and moisture content are taken into account, respectively. Satisfactory results have been obtained, indicating that the proposed approach is capable of dealing with complex nonlinear problems.

Effect of different fertilization time after human chorionic gonadotropin injection on fertilization outcome of patients in vitro fertilizationembryo transfer

Objective:To explore the effect of different fertilization time after human chorionic gonadotropin(HCG)injection on the outcome of fertilization in vitro fertilization-embryo transfer(IVF-ET).Methods:One thousand one hundred and forty IVF-ET cycles from January 2016 to August 2018 were analyzed retrospectively.According to the different fertilization time after injection of HCG divided into four groups:Group A(38.0 h~39.0 h),Group B(39.1 h~40.0 h),Group C(40.1 h~41.0 h),and Group D(41.1 h~42.0 h).The normal fertilization rate,the normal cleavage rate,the embryo utilization rate,the high-quality embryo rate,the clinical pregnancy rate,the implantation rate,and the spontaneous abortion rate were analyzed among the groups.Then we investigated the effect of different promotion methods on the outcome of fertilization during the optimal fertilization time.Results:There was no significant difference in 2PN cleavage rate,available embryo rate,clinical pregnancy rate,implantation rate and abortion rate among the four groups(P>0.05).The high-quality embryo rate in Group D(44.6%)was the highest,and was significantly different among the four groups(P<0.05).The normal fertilization rate in Group D(71.6%)was the highest,and was significantly different among the four groups(P<0.05).The normal fertilization rate(78.1%)of antagonist group was significantly higher than other groups(P<0.05).Conclusion:The different fertilization time after HCG injection have effects on high-quality embryo rate and normal fertilization rate of patients in IVF-ET.The appropriate fertilization time of patients in IVF-ET was 41 h~42 h after HCG injection in our reproductive center,improved the clinical pregnancy rate and reduced the early abortion rate.The GnRH-ant protocol is superior to other protocol in IVF-ET.

Time-lapse技术联合一步法培养对胚胎发育及妊娠结局的影响

目的比较时差成像(Time-lapse imaging TLI)系统培养与常规低氧培养的胚胎发育情况和妊娠结局的差异。方法回顾性分析2020年12月至2022年5月在广东医科大学附属医院生殖中心接受体外受精或卵胞浆内单精子注射-胚胎移植(IVF/ICSI-ET)治疗的年轻患者(20≤年龄≤35岁)的临床资料,根据胚胎培养方式分为TLI系统培养组(TLI组,n=254)和常规培养组(常规组,n=317),比较两组患者间基本资料及胚胎发育情况;再根据胚胎移植类型分为D3卵裂期胚胎移植(TLI组127例,常规组127例)和D5囊胚移植(TLI组99例,常规组143例)亚组,分别统计不同胚胎移植类型下两种培养方式的临床妊娠结局差异。结果两组患者的基本资料比较均无显著性差异(P>0.05);常规组的成熟卵母细胞率(87.2%vs.85.5%)、总受精率(77.1%vs.73.1%)、2PN卵裂数[9(6.0,13.5)vs.9(6.0,12.0)]、优胚率(38.7%vs.36.1%)均显著高于TLI组(P<0.05);两组患者间的优胚数、囊胚数、MⅡ卵母细胞数、受精总数、2PN数、卵裂总数、囊胚形成率、2PN率、2PN卵裂率、卵裂胚胎利用率的差异均无统计学意义(P>0.05)。D3卵裂期胚胎移植中,常规组的移植胚胎数显著高于TLI组[(1.80±0.11)vs.(1.68±0.47),P<0.05],两种培养方式组间胚胎着床数、种植率、HCG阳性率、临床妊娠率及双胎妊娠率均无显著性差异(P>0.05),但常规组双胎率稍高于TLI组(33.8%vs.20.3%,P>0.05);D5囊胚移植中,两种培养方式组间胚胎着床数、种植率、临床妊娠率均无显著性差异(P>0.05),但TLI组临床妊娠率稍高于常规组(65.7%vs.55.9%,P>0.05)。结论常规培养方式由于其经济、简便,是目前大多数中心的常用有效培养方法;针对年轻不孕妇女,TLI培养可能有效挑选更有种植潜力的胚胎,可能有助于提高种植率、保证妊娠率,且单胚胎移植有效减少多胎妊娠。

Relocation moveson——It’s time for China’s textile industry to transfer

History proves that some countries and regions benefited from international industry transfer, because of international industrial transfer can stimulate their economic growth.Thanks to the manufacturing transfer implemented by EU, USA, Japan and some Asian developed countries in 1980s, China’s economic situation has boomed over 30 years. Textile industry as a traditional industry in China has its own competitive advantage. It can be confirmed that textile industry will play an important role during the fourth Industry transfer period. So, who will be the winner this time?

Adaptive Time Slot Resource Allocation in SWIPT IoT Networks

The rapid advancement of Internet of Things(IoT)technology has brought convenience to people’s lives;however further development of IoT faces serious challenges,such as limited energy and shortage of network spectrum resources.To address the above challenges,this study proposes a simultaneous wireless information and power transfer IoT adaptive time slot resource allocation(SIATS)algorithm.First,an adaptive time slot consisting of periods for sensing,information transmission,and energy harvesting is designed to ensure that the minimum energy harvesting requirement ismet while the maximumuplink and downlink throughputs are obtained.Second,the optimal transmit power and channel assignment of the system are obtained using the Lagrangian dual and gradient descent methods,and the optimal time slot assignment is determined for each IoT device such that the sum of the throughput of all devices is maximized.Simulation results show that the SIATS algorithm performs satisfactorily and provides an increase in the throughput by up to 14.4%compared with that of the fixed time slot allocation(FTS)algorithm.In the case of a large noise variance,the SIATS algorithm has good noise immunity,and the total throughput of the IoT devices obtained using the SIATS algorithm can be improved by up to 34.7%compared with that obtained using the FTS algorithm.

Dynamic Ensemble Multivariate Time Series Forecasting Model for PM2.5

In forecasting real time environmental factors,large data is needed to analyse the pattern behind the data values.Air pollution is a major threat towards developing countries and it is proliferating every year.Many methods in time ser-ies prediction and deep learning models to estimate the severity of air pollution.Each independent variable contributing towards pollution is necessary to analyse the trend behind the air pollution in that particular locality.This approach selects multivariate time series and coalesce a real time updatable autoregressive model to forecast Particulate matter(PM)PM2.5.To perform experimental analysis the data from the Central Pollution Control Board(CPCB)is used.Prediction is car-ried out for Chennai with seven locations and estimated PM’s using the weighted ensemble method.Proposed method for air pollution prediction unveiled effective and moored performance in long term prediction.Dynamic budge with high weighted k-models are used simultaneously and devising an ensemble helps to achieve stable forecasting.Computational time of ensemble decreases with paral-lel processing in each sub model.Weighted ensemble model shows high perfor-mance in long term prediction when compared to the traditional time series models like Vector Auto-Regression(VAR),Autoregressive Integrated with Mov-ing Average(ARIMA),Autoregressive Moving Average with Extended terms(ARMEX).Evaluation metrics like Root Mean Square Error(RMSE),Mean Absolute Error(MAE)and the time to achieve the time series are compared.

A Hybrid Neural Network Model Based on Transfer Learning for Forecasting Forex Market

The forecasting research literature has developed greatly in recent years as a result of advances in information technology. Financial time-series tasks have made substantial use of machine learning and deep neural networks, but building a prediction model from scratch takes time and computational resources. Transfer learning is growing popular in tackling these constraints of training time and computational resources in several disciplines. This study proposes a hybrid base model for the financial time series prediction employing the recurrent neural network (RNN) and long-short term memory (LSTM) called RNN-LSTM. We used random search to fine-tune the hyperparameters and compared our proposed model to the RNN and LSTM base models and evaluate using the RMSE, MAE, and MAPE metrics. When forecasting Forex currency pairs GBP/USD, USD/ZAR, and AUD/NZD our proposed base model for transfer learning outperforms RNN and LSTM base model with root mean squared errors of 0.007656, 0.165250, and 0.001730 respectively.

非厄米物理启发的高效无线电能传输

无线电能传输技术是指不需要线缆或者波导结构,利用电磁波直接将电能从电源传输到负载的技术。作为能量传输的一种全新方式,无线电能传输技术可以极大地提高供电设备的安全性、可靠性和便捷性,其在消费电子行业、自动化工业车间以及人工智能平台等需要高自由度供能的场景中具有重要的应用价值。目前无线电能传输技术仍存在一定的局限性,特别是对于广为关注的磁共振耦合无线电能传输技术,面临着高效率和稳定性难以兼顾的巨大挑战。文章以近场无线电能传输技术为研究框架,深入介绍非厄米新物理在无线电能传输系统中的调控机理,及其在高效、稳定、待机功率损耗、电磁环境兼容等方面的突出优势,最后对无线电能传输未来的研究方向进行了展望。