美国FORGE计划犹他州干热岩开发示范项目进展综述

21世纪是全球能源获取方式发生重要变化的时代。现有以煤炭、石油、天然气等传统资源为基础的能源正在逐渐被风能、太阳能、生物质能、地热能等环境友好、低排放的绿色能源所取代。干热岩是一种不含原生水(或含少量水但不能流动)的高温地热资源,可通过水力刺激改造形成增强型地热系统储层,从而提取数量相当可观的地热能。本文以美国能源部正在组织实施的FORGE计划犹他州干热岩示范项目为研究对象,综述了项目在场地地质条件表征、基础设施建设等方面取得的主要进展与成果,总结了项目在高温硬岩钻井、储层建造、微震监测等方面取得的广泛且深入认识,从统筹部署、组织实施、场地表征和设施建设、关键技术装备突破、数据共享等方面提出了值得我国借鉴参考的具体实践。

Effect of nitrogen content on the microstructure and mechanical properties of titanium-bearing nonquenched and tempered steel after hot forging

The microstructure and mechanical properties of titanium(Ti)-bearing medium-carbon nonquenched and tempered steel with different nitrogen content before and after hot forging were investigated through smelting,forging,and laboratory tests.The results show that the grain size of nonquenched and tempered steel was gradually refined,and the ferrite content gradually increased with an increase in nitrogen content.The grain size of the material with low nitrogen content increased abnormally,and its impact properties significantly decreased after hot forging.The grain size of nonquenched and tempered steel with higher nitrogen content was slightly larger than that before forging,and the tensile and yield strength increased,but the impact toughness was not significantly reduced.The Ti-bearing nonquenched and tempered steel showed better strength and toughness after hot forging with the addition of 0.010%0.015%nitrogen.

Simulation-Based Investigation of Crack Formation in Forged MB15 Magnesium Alloy

In the process of riveting an MB15 forging die,cracks were discovered emerging along the longitudinal direction and near the riveting hole.Through fracture analysis,microscopic observation,energy spectrum analysis,metallographic examination,and hardness test,the properties and causes of the cracks are discussed.The results indicate that the cracking type is intergranular brittle cracking,occurring during the forging stage.Furthermore,the recrystallization at the crack site is found to be incomplete,which is attributed to the low deformation temperature.

基于Simufact Forging高铁轮毂锻压成形工艺仿真

基于Simufact Forging有限元分析软件对高铁轮毂成形过程进行了仿真,着重研究了轮毂辗扩过程中的等效塑性应变、等效应力及材料流动。结果表明:高铁轮毂在辗扩过程中材料整体变形基本一致,可以获得较好的力学性能;随着锻压成形不断的进行,轮毂内圈塑性应变逐渐变大;成形过程中整个轮毂应力分布较为均匀。

MICROSTRUCTURAL MODEL OF GATORIZED WASPALOY IN THE ISOTHERMAL FORGING PROCESS

A microstructural model, which was to predict the evolution of microstructure of Gatorized Waspeloy in the isothermal forcing process, was developed in terms of dynamic recrystallization and grain growth. Three steps of experiment were conducted during developing the model: (1) .Specimens were compressed in M FS testing machine; (2) Dynamic recrystallization and grain growth were discussed; (3) Dynamic recrys- tallization model and grain growth mode were set up. The agreement of simulated results and experimental data is fine.

NUMERICAL SIMULATION OF FORGING AND SUBSEQUENT HEAT TREATMENT OF A ROD BY A FINITE VOLUME METHOD

A method to simulate processes of forging and subsequent heat treatment of an axial symmetric rod is formulated in eulerian description and the feasibility is investigated. This method uses finite volume mushes for troching material deformation and an automatically refined facet surface to accurately trace the free surface of the deforming material.In the method,the deforming work piece flows through fixed finite volume meshes using eulerian formulation to describe the conservation laws,Fixed finite volume meshing is particularly suitable for large three-dimensional deformation such as forging because remeshing techniques are not required, which are commonly considered to be the main bottelencek in the ssimulations of large defromation by using the finite element method,By means of this finite volume method, an approach has been developed in the framework of "metallo-thermo-mechanics" to simulate metallic structure, temperature and stress/strain coupled in the heat treatment process.In a first step of simulation, the heat treatment solver is limited in small deformation hypothesis,and un- coupled with forging. The material is considered as elastic-plastic and takes into account of strain, strain rate and temperature effects on the yield stress.Heat generation due to deformation,heat con- duction and thermal stress are considered.Temperature - dependent phase transformation,stress-in- duced phase transformation,latent heat,transformation stress and strain are included.These ap- proaches are implemented into the commerical commercial computer program MSC/SuperForge and a verification example with experimental date is given as comparison.

Computer Aided Simulation on Precision Cold Forging of Universal Joint Cross

The 3D FEM numerical simulation on multi-action precision cold forging technology of universal joint cross and differential spider is done in this article using DEFORM Software, a commercial computer aided engineering software specializing in forming and heat treatment simulation technology, and suitable for cold, warm and hot forging process. The material flow properties, the dynamic variation of stress and strain in the process of deformation and the load-stroke curve have also been achieved. A good consistency is exhibited between simulation results and practical data. Based on the DEFORM simulation results, the optimized procedure has been found for forging a universal joint cross. What should be emphasized here is that a better understanding of practical forging characters and the environmental factors can greatly improve the simulation accuracy thus make the simulation results more reliable.

Numerical simulation on forging process of TC4 alloy mounting parts

In order to eliminate forging defects appearing in production,based on the rigid-viscoplastic FEM principle,the DEFORM3D software package was employed to simulate the forming process of TC4 alloy mounting part and to optimize the process parameters.In this simulation,the temperature dependency of the thermal and mechanical properties of material was considered.Based on the simulation,the metal flow and thermomechanical field variables such as stress and damage are obtained.The simulation results show that the forging defects are caused by improper die dimension and the optimized die dimension was proposed.To verify the validity of simulation results,forging experiments were also carried out in a forging plant.The forging experiments show that the optimized die dimension can ensure the quality of forging part,and it can provide reference to improve and optimize die design process.

Effect of Zn/Mg/Cu Additions on Hot Cracking Tendency and Performances of Al-Cu-Mg-Zn Alloys for Liquid Forging

During the process of liquid forging, a host of hot cracking defects were found in the Al-CuMg-Zn aluminum alloy. Therefore, mechanical tests and analyses by optical microscope, scanning electron microscope, and X-ray diffraction were performed to research the influences of zinc, magnesium, and copper(three main alloying elements) on hot cracking tendency and mechanical properties. It was concluded that all the three alloying elements exerted different effects on the performances of newly designed alloys. And the impact of microstructures on properties of alloys was stronger than that of solution strengthening. Among new alloys, Al-5 Cu-4.5 Mg-2.5 Zn alloy shows better properties as follows: σb=327 MPa, δ=2.7%, HB=107 N/mm^2, and HCS=40.

STRESS FIELD ANALYSIS OF EXTRA-HEIGHT FORGING DIE USING FINITE ELEMENT METHOD

ＴｈｅｅｘｔｒａｈｅｉｇｈｔｆｏｒｇｉｎｇｄｉｅｉｎＳｏｕｔｈｅｗｅｓｔＡｌｕｍｉｎｉｕｍＦａｂｒｉｃａｔｉｏｎＰｌａｎｔｉｓａｓｐｅｃｉａｌｄｉｅｆｏｒｍａｋｉｎｇａｒｍａｍｅｎｔａｎｄｓｐｅｃｉａｌｃｉｖｉｌｐｒｏｄｕｃｔｓｉｎＣｈｉｎａ．Ａ...

Impedance Analysis of Forging Process and Strategy Study on Compliance for Forging Manipulator

In the field of heavy forging, there are numerous researches on deformation rule in forging process by FEM simulation, however, not many scholars take the equipment constraint and the mutual reaction load between the forging manipulator clamp and the forging blank into account, which will impact on safety of manipulator body and quality of forging blank. This paper presents an impedance model to describe the load and formulates compliance strategies correspondingly to reduce the mutual reaction load for forging manipulator. Firstly, an FEM model of forging process is built. Meanwhile, the clamp of forging manipulator is added to the model as movement constraint and interaction part between the manipulator and the forming process. Secondly, a typical forging process is simulated by changing the movement constraint, and then an impedance model is established to describe the relationship between the load and movement constraint. Finally, two kinds of compliance strategies are formulated according to the impedance model, one is called free compliance, and the other is initiative/passive compliance. The simulation results show that compliance strategies reduce the load amounting to 5 000 kN in z direction between the manipulator clamp and the forging blank obviously, which may lead to serious accidents, such as the capsizing of forging manipulator, the fracture of manipulator clamp, and so on. The proposed research simulates the more real forging process, gets the initiative/passive compliance strategy which is more simple and suitable to the real producing and better for forming a forging process planning and control system in the modern production, and improves the quality and efficiency of heavy forging.

Microstructural evolution of Mg-7Al-2Sn Mg alloy during multi-directional impact forging

Multi-directional impact forging(MDIF)was applied to a Mg-7Al-2Sn(wt.%)Mg alloy to investigate its effect on the microstructural evolution.MDIF process exhibited high grain refinement efficiency.After MDIF 200 passes,the grain size drastically decreased to 20µm from the initial coarse grains of~500µm due to dynamic recrystallization(DRX).Meanwhile,original grain boundaries remained during MDIF and large numbers of fine sphericalβ-Mg_(17)Al_(12) particles dynamically precipitated along the original grain boundaries with high Al concentration,acting as effective pinning obstacles for the suppression of DRXed grain growth.Besides,micro-cracks nucleated during MDIF and propagated along the interface between the remained globular or cubic Al-Mn particles and Mg matrix.

Effect of pre-induced twinning on microstructure and tensile ductility in GW92K magnesium alloy during multi-direction forging at decreasing temperature

Effect of pre-induced twinning on the microstructure evolution and mechanical properties of extruded Mg-9.26Gd-2.08Y-0.36Zr(GW92K)alloy have been investigated during multi-direction forging with large strains at decreasing temperature from 400℃ to 300℃.The results showed that,whether there pre-induced twinning existing in the initial microstructure by pre-deformation or not,a mixed microstructure of residual coarse grains and notably refined grains formed under both conditions,combing with some residual coarse grains with less deformation inside grains and lots of dispersed nano-precipitates distributed along refined grain boundaries.However,a significant improvement with the tensile ductility was obtained by the pre-induced twinning in the former alloy.It was suggested that,the pre-induced twinning largely contributed to the grain refinement and lead to an increase in the ratio of fine grain structure which would be responsible for the better properties.Furthermore,during subsequent forging deformation in the pre-deformed sample,the grain refinement mechanism by gradual grain orientation rotation around the surface section in residual coarse-grains was a little different from that by the macro-shear deformation in the as-extruded condition.

Experimental study and numerical simulation of isothermal closed die forging for aluminium alloy rotor

The closed die forging(or fully-enclosed die forging) method was employed to form a rotor instead of the conventional machining method. A combined female die was designed so that the rotor could be released easily from the female die after forging. In order to improve the metal flow ability, the isothermal forming technique was introduced to the closed die forging process. On the basis of the rigid-viscoplastic FEM principle, the DEFORM 3D software package was employed to simulate the forming process. The simulation results illustrate that the deformation of different part of the billet is not the same. The material near the entrance of the die cavity is deformed greatly whose strain rate and strain are both large, while the deformation of the material at the billet center is much smaller.

FINITE ELEMENT MODEL AND SIMULATION OF ROTARY FORGING OF A DISC

The rotary forging process of a disc is simulated by 3-D finite element method.The motion of the rotary the is described as the combination of a revolution round the machine axis and a spin round the rotary die axis. Therefore, the workpiece can be loaded and unloaded partly and cyclically by the cone surface of the rotary the continuously, according with the practical rotary forging process. From the siumulation rasults, the causes of center-thinning during rotary forging of discs are that the locally loading of rotary die made the workpiece center get high radial and tangential tensile stresses, and then the shortening in axial direction and the elongating in tangential and radial direction occur continuous- ly.

Ductility enhancement of EW75 alloy by multi-directional forging

In this study,the Mg-7Gd-5Y-1Nd-0.5Zr alloy can reach a high ductility by the process of multi-directional forging,and the evolution of the microstructure,texture and the mechanical properties were discussed systematically.The results show that after the solutionized sample was multi-forged at 500℃,its grain size can be refined from 292 um to 58 um.As the forging temperature decreased,fine particles precipitated in the matrix.The volume fraction of the particles increased with the forging temperature decreasing,so the nucleation and growth of crystallization were strongly restricted.There was no recrystallization as the forging temperature fell to 410℃,and the severe deformed grains distributed as streamlines perpendicular to the final compression axis.The texture intensity decreased with increasing forging passes.The sample with best ductility was obtained after compressed at 470℃,with an elongation to failure of 21%at room temperature,which is increased by 200%,in comparison with that of the samples in solutionized condition.EBSD results revealed that the mean grain size was 15 um.Refined grains as well as the weakened texture were the key factors to its high ductility.

Tempering stability of Fe–Cr–Mo–W–V hot forging die steels

The tempering stability of three Fe–Cr–Mo–W–V hot forging die steels(DM, H21, and H13) was investigated through hardness measurements and transmission electron microscopy(TEM) observations. Both dilatometer tests and TEM observations revealed that DM steel has a higher tempering stability than H21 and H13 steels because of its substantial amount of M_2C(M represents metallic element) carbide precipitations. The activation energies of the M_2C carbide precipitation processes in DM, H21, and H13 steels are 236.4, 212.0, and 228.9 kJ/mol, respectively. Furthermore, the results indicated that vanadium atoms both increase the activation energy and affect the evolution of M_2C carbides, resulting in gradual dissolution rather than over-aging during tempering.

STRESS ANALYSIS OF CANNED HOT FORGING SPECIMEN OF TiAl INTERMETALLIC COMPOUND

ＳＴＲＥＳＳＡＮＡＬＹＳＩＳＯＦＣＡＮＮＥＤＨＯＴＦＯＲＧＩＮＧＳＰＥＣＩＭＥＮＯＦＴｉＡｌＩＮＴＥＲＭＥＴＡＬＬＩＣＣＯＭＰＯＵＮＤ①ＲａｏＱｉｕｈｕａＤｅｐａｒｔｍｅｎｔｏｆＡｒｃｈｉｔｅｃｔｕｒｅＥｎｇｉｎｅｒｉｎｇ，ＨｅＹｅｈｕｉ，Ｈｕａｎｇ...

Inner-product of strain rate vector through direction cosine in coordinates for disk forging

A new linear integration for plastic power was proposed.The effective strain rate for disk forging with bulge was expressed in terms of two-dimensional strain rate vector,and then its direction cosines were determined by the ratio of coordinate increments.Furthermore,inner-product of the vector for plastic power was term integrated by term and summed.Thereafter,through a formula for determination of bulge an analytical solution of stress effective factor was obtained.Finally,through compression tests,the calculated results of above formula were compared with those of Avitzur’s approximate solution and total indicator readings of the testing machine.It is indicated that the calculated compression forces are basically in agreement with the measured ones if the pass reduction is less than 13.35%.However,when the reduction gets up to 25.34% and 33.12%,the corresponding errors between the calculated and measured results also get up to 6% and 13.5%,respectively.

Microstructures and mechanical properties of 2014 aluminium alloy forgings made by a new process

The triangular 2014 aluminium alloy forgings were made by a new process and the traditional process. The results showed that the mechanical properties of the forgings made by the new process are far higher than that in the standard of GB223 84, and also higher than that in the standard of EL/53MI 94; moreover, the mechanical properties are almost the same in each direction, and anisotropies are very small. The grains and 2nd phases were analyzed by using TEM and SEM, the results indicate that very fine grains (3～6 μm)appear in an approximately isometric way, and a large number of 2nd submicrophases(0.05～0.15 μm) disappear in no apparently preferred orientation distribution because the new process involves multidirectional heavy plastic deformation (λ=12), solution(500 ℃/400 min) and ageing(165 ℃/10 h) heat treatments for a long time at high temperatures. These refined grains, 2nd submicrophases and their almost homogeneous distribution can make it possible for the forgings to display high mechanical properties.