Waste heat recovery from hot steel slag on the production line:Numerical simulation,validation and industrial test

Waste heat recovery from hot steel slag was determined in a granular bed through the combination of numerical simulation and an industrial test method.First,the effective thermal conductivity of the granular bed was calculated.Then,the unsteady-state model was used to simulate the heat recovery under three different flow fields(O-type,S-type,and nonshielding type(Nontype)).Second,the simulation results were validated by in-situ industrial experiments.The two methods confirmed that the heat recovery efficiencies of the flow fields from high to low followed the order of Nontype,S-type,and O-type.Finally,heat recovery was carried out under the Nontype flow field in an industrial test.The heat recovery efficiency increased from~76%and~78%to~81%when the steel slag thickness decreased from 400 and 300 to 200 mm,corresponding to reductions in the steel slag mass from 3.96 and 2.97 to 1.98 t with a blower air volume of 14687 m^(3)/h.Therefore,the research results showed that numerical simulation can not only guide experiments on waste heat recovery but also optimize the flow field.Most importantly,the method proposed in this paper has achieved higher waste heat recovery from hot steel slag in industrial scale.

Off-Design Simulation of a CSP Power Plant Integrated with aWaste Heat Recovery System

Concentrating Solar Power(CSP)plants offer a promising way to generate low-emission energy.However,these plants face challenges such as reduced sunlight during winter and cloudy days,despite being located in high solar radiation areas.Furthermore,their dispatch capacities and yields can be affected by high electricity consumption,particularly at night.The present work aims to develop an off-design model that evaluates the hourly and annual performances of a parabolic trough power plant(PTPP)equipped with a waste heat recovery system.The study aims to compare the performances of this new layout with those of the conventional Andasol 1 plant,with the aim of assessing the improvements achieved in the new design.Based on the results,it can be concluded that the new layout has increased the annual generated power to almost 183 GWh(an increase of about 7.60% is achieved compared to the Andasol 1 layout that generates 169 GWh annually).Additionally,the proposed installation has achieved an efficiency of 20.55%,which represents a 7.87% increase compared to the previous design(19.05%).The Levelized Cost of Electricity(LCOE)of the new layout has been reduced by more than 5.8% compared to the Andasol 1 plant.Specifically,it has decreased from 13.11 to 12.35 c/kWh.This reduction in LCOE highlights the improved cost-effectiveness of the newlayout,making it amore economically viable option for generating electricity compared to the conventional Andasol 1 plant.

Application of the waste heat recovery system and energy-saving in the strip continuous annealing furnace

The common problem of cold strip continuous annealing furnaces is high exhaust gas temperature and great energy consumption. Taking the cold-strip continuous annealing furnaces of Baosteel No. 4 cold mill plant as an example, several waste heat recovery systems in the annealing furnaces are compared and their advantages and disadvantages are analyzed through different energy-saving technologies.

Energy,Exergy,and Exergoeconomic Analysis of Solar-Driven Solid Oxide Electrolyzer System Integrated with Waste Heat Recovery for Syngas Production

Syngas fuel generated by solar energy integrating with fuel cell technology is one of the promising methods for future green energy solutions to carbon neutrality.This paper designs a novel solar-driven solid oxide electrolyzer system integrated with waste heat for syngas production.Solar photovoltaic and parabolic trough collecter together drive the solid oxide electrolysis cell to improve system efficiency.The thermodynamic models of components are established,and the energy,exergy,and exergoeconomic analysis are conducted to evaluate the system’s performance.Under the design work conditions,the solar photovoltaic accounts for 88.46%of total exergy destruction caused by its less conversion efficiency.The exergoeconomic analysis indicates that the fuel cell component has a high exergoeconomic factor of 89.56%due to the large capital investment cost.The impacts of key parameters such as current density,operating temperature,pressure and mole fraction on system performances are discussed.The results demonstrate that the optimal energy and exergy efficiencies are achieved at 19.04%and 19.90%when the temperature,pressure,and molar fraction of H_(2)O are 1223.15 K,0.1 MPa,and 50%,respectively.

Effect of flue gas outlet temperature in evaporator on thermal economic performance of organic Rankine cycle system for sinter waste heat recovery

In order to improve the recovery and utilization rates of sinter waste heat effectively,the organic Rankine cycle(ORC)system with subcritical cycle was designed to recover the low-temperature sinter cooling flue gas waste heat in an annular cooler for power generation.The thermodynamic,economic and multi-objective optimization models of ORC system were established,and R600a was selected as the ORC working medium.Subsequently,the variations in system thermodynamic performance and economic performance with the ORC thermal parameters were discussed in detail,and the optimal ORC thermal parameters were determined.The results show that the system net output power increases with increasing the evaporation temperature and decreasing the condensation temperature and increases first and then,decreases with the increase in superheat degree for a given flue gas outlet temperature in the evaporator,while the heat transfer area per unit net output power appears different variation trends in various ranges of flue gas outlet temperature.Taking the sinter cooling flue gas waste heat of 160℃as the ORC heat source,the optimal thermal parameters of ORC system were the flue gas outlet temperature of 90℃,the evaporation temperature of 95℃,the superheat degree of 10℃,and the condensation temperature of 28℃.

Simulation Analysis of Flue Gas Waste Heat Utilization Retrofit Based on ORC System

Recovery of waste heat from boiler flue gas is an effective way to improve energy utilization efficiency.Taking a heating station heating project as an example,the existing heating system of this heating station was analyzed for its underutilized flue gas waste heat and low energy utilization rate.Rankine cycle is an effective waste heat recovery method,and a steam boiler organic Rankine cycle(ORC)cogeneration waste heat utilization method is proposed.The system model simulation is constructed and verified.First,a thermodynamic model was constructed in MATLAB and five suitable work gases were selected to analyze the effects of evaporation temperature and condensation temperature on the network and thermal efficiency of the waste heat cycle power system.Secondly,the ORC model is invoked in TRNSYS to construct the improved cogeneration system,and the rationality of the remaining heat utilization methods is determined by calculating and analyzing the thermal performance,economy,and environmental protection of the improved system.The simulation results show that the system can generate about 552,000 kWh of electricity per year,and improving the energy utilization rate from 0.72 to 0.78.

A review of concentrated photovoltaic-thermal(CPVT) hybrid solar systems with waste heat recovery(WHR)

In conventional photovoltaic(PV) systems, a large portion of solar energy is dissipated as waste heat since the generating efficiency is usually less than 30%. As the dissipated heat can be recovered for various applications, the wasted heat recovery concentrator PV/thermal(WHR CPVT) hybrid systems have been developed. They can provide both electricity and usable heat by combining thermal systems with concentrator PV(CPV) module, which dramatically improves the overall conversion efficiency of solar energy.This paper systematically and comprehensively reviews the research and development of WHR CPVT systems. WHR CPVT systems with innovative design configurations, different theoretical evaluation models and experimental test processes for several implementations are presented in an integrated manner. We aim to provide a global point of view on the research trends, market potential, technical obstacles, and the future work which is required in the development of WHR CPVT technology. Possibly, it will offer a generic guide to the investigators who are interested in the study of WHR CPVT systems.

Energy management strategy for hybrid electric vehicle integrated with waste heat recovery system based on deep reinforcement learning

Hybrid electric vehicles(HEVs)are acknowledged to be an effective way to improve the efficiency of internal combustion engines(ICEs)and reduce fuel consumption.Although the ICE in an HEV can maintain high efficiency during driving,its thermal efficiency is approximately 40%,and the rest of the fuel energy is discharged through different kinds of waste heat.Therefore,it is important to recover the engine waste heat.Because of the great waste heat recovery performance of the organic Rankine cycle(ORC),an HEV integrated with an ORC(HEV-ORC)has been proposed.However,the addition of ORC creates a stiff and multi-energy problem,greatly increasing the complexity of the energy management system(EMS).Considering the great potential of deep reinforcement learning(DRL)for solving complex control problems,this work proposes a DRL-based EMS for an HEV-ORC.The simulation results demonstrate that the DRL-based EMS can save 2%more fuel energy than the rule-based EMS because the former provides higher average efficiencies for both engine and motor,as well as more stable ORC power and battery state.Furthermore,the battery always has sufficient capacity to store the ORC power.Consequently,DRL showed great potential for solving complex energy management problems.

Comparison of Conventional and Advanced Exergy Analysis for Dual-Loop Organic Rankine Cycle used in Engine Waste Heat Recovery

At present,the dual-loop organic Rankine cycle(DORC)is regarded as an important solution to engine waste heat recovery(WHR).Compared with the conventional exergy analysis,the advanced exergy analysis can better describe the interactions between system components and the irreversibility caused by economic or technical limitations.In order to systematically study the thermodynamic performance of DORC,the conventional and advanced exergy analyses are compared using an inline 6-cylinder 4-stroke turbocharged diesel engine.Meanwhile,the sensitivity analysis is implemented to further investigate the influence of operating parameters on avoidable-endogenous exergy destruction.The analysis result of conventional exergy analysis demonstrates that the priorities for the components that should be improved are in order of the high-temperature evaporator,the low-temperature turbine,the first low-temperature evaporator and the high-temperature condenser.The advanced exergy analysis result suggests that the avoidable exergy destruction values are the highest in the low-temperature turbine,the high-temperature evaporator and the high-temperature turbine because they have considerable endogenous-avoidable exergy destruction.The sensitivity analysis indicates that reducing the evaporation pinch point and raising the turbine efficiency can decrease the avoidable exergy destruction.

Experimental Analysis of Atypically Long Finned Oscillating Heat Pipe for Ventilation Waste Heat Recovery Application

Oscillating heat pipes(OHP)which are constructed from a serpentine-arranged capillary tube possess a desirable aerodynamic form factor and provide for relatively high heat transfer rates via cyclic evaporation and condensation of an encapsulated working fluid with no internal wicking structure required.In last two decades,OHP has been extensively investigated for its potential application in thermal management of various applications.This study presents an experimental investigation on the heat transfer performance of an atypically long finned OHP.The heat transfer performance of the proposed OHP was analyzed and compared with a bare tube OHP with similar overall dimensions.Results show that a unit row of finned OHP filled with n-pentane with fill ratio of 70%can recover up to(400±40)W of heat from a typical waste exhaust air stream.The additional pressure drop due to fins was estimated to be(6.8±2)Pa resulting in an increase of 1–2 W of fan power consumption.The average heat recovery rate via finned OHP was found to be almost 80%more than bare tube OHP filled with same working fluid with same fill ratio.

Comprehensive evaluation of marine waste heat recovery technologies based on Hierarchy-Grey correlation analysis

In this study,comprehensive evaluation of the technologies on waste heat recovery technologies for maritime applications has been carried out.We have focused our research on exhaust gas turbine system(EGT),thermodynamic organic rankine cycle(RC),Kalina cycle(KC)and thermoelectric generators(TG),which are the most appropriate and most up-to-date techniques for recovering power from marine engines.Each technology has its own advantages and disadvantages,so the comprehensive evaluation of these technologies is essential to accurately determine which technology will be applied to which target.This belongs to the multi-criteria decision(MCDM)process.The combined assessment methodology,consisting of gray correlation and analysis hierarchy processes,has been applied to evaluate four waste heat recovery techniques in terms of technical,economic,social and environmental aspects.According to the comparison results,the exhaust gas turbine system has been evaluated as the most promising technology among the various WHR technologies that can be applied to marine engines.Sensitivity analysis suggests that if investment cost of TG falls to about the same level as the one of EGT,TG could be the best method among these technologies.Reduction of investment cost of TG technology could be realized by development of low cost thermoelectric material.We have analyzed the correlation between each cost through DOE analysis and investigate the effect of individual costs on the total cost.This work helps in identifying the most suitable heat recovery technologies for marine engine.

A four-dimensional interaction-based appraisal approach towards the performance enhancement of a vehicular waste heat recovery system

The non-linear multifactorial impacts on fuel-saving potential constrain the practical performance of the vehicular waste heat recovery system(WHRS). This study proposed a four-dimensional interaction-based appraisal approach to interpreting these impacts for enhancing WHRS's in-vehicle performance. The interaction incorporates a heat exchanger, configuration, engine,and vehicle. The proposed approach comprises two successive steps, emphasizing evaluation under the rated(Step 1) and off-design(Step 2) heat source conditions. A case study of waste heat recovery from a passenger vehicle was conducted to evaluate the in-vehicle performance of a novel co-split system and two single-split ones(with/without a regenerator) through this approach. The novel system theoretically modifies vehicular performance but remains ambiguous concerning real-world behaviour, which is assessed and verified by the proposed approach. Two key factors determining vehicular performance were identified by Step 1, namely, net power output and engine backpressure. As the co-split system modified both factors, its fuel-saving potential could be increased by up to 20.3% compared with single-split systems. Also, the limiting factor for off-design performance was pinpointed by Step 2, namely, the mismatch between the heat source and working fluid, which led to the solution, i.e., the synergistic split regulation of the working fluid and heat source. An up to 8.8% improvement in net power output was achieved by the co-split system at off-design heat sources compared with fixed split ratios. Consequently, the approach enables holistic performance improvement of the vehicular WHRS under design/off-design heat source conditions.

Thermodynamic and Economic Studies of a Combined Cycle for Waste Heat Recovery of Marine Diesel Engine

In the present study,the thermodynamic and economic performance of a combined thermodynamic cycle formed by an ORC and a Kalina cycle,which can simultaneously recover waste heat of exhaust gas and cooling water of marine engine,has been analyzed.Two typical marine engines are selected to be the waste heat source.Six economic indicators are used to analyze the economic performance of this combined thermodynamic cycle system with different marine engine load and under practical comprehensive operating condition of marine engine.The results of the present study show that the combined thermodynamic cycle system with R123 as organic working fluid has the best performance.The system with cis-butene has the worst economic performance.Under practical comprehensive operating conditions of ships,R123 has the shortest Payback Periods,which are 8.51 years and 8.14 years for 8 S70 ME-C10.5 engine and 5G95 ME-C10.5 engine,respectively.Correspondingly,payback Periods of Cyclopentane are 11.95 years and 11.90 years.The above values are much shorter than 25 years which are the lifetime of a marine ship.Under practical comprehensive operating conditions of ships,the combined cycle system can provide output power which is at least equivalent to 25%of engine power.Considering that R123 will be phased out in near future,cyclopentane may be its good successor.Cyclopentane can be used safely by correct handling and installing according to manufacturer's instructions.

Evaluation of Waste Heat Recovery of Electrical Powertrain with Electro-thermally Coupled Models for Electric Vehicle Applications

The mile range of an electric vehicle(EV)may be reduced significantly in cold weather owing to the energy demand for meeting thermal comfort in the vehicle cabin,as waste heat from a combustion engine is not available for this purpose.Various heat pump-based heating,ventilation,and air conditioning(HVAC)systems can be employed to absorb the heat energy from the surroundings and/or the waste heat from the electrical powertrain to facilitate cabin thermal comfort,thereby extending the EV mile range.However,there is a lack of research on the electro-thermally coupled modelling and evaluation of the thermal performance of HVAC systems.This paper proposes electro-thermally coupled models for the electrical machine and inverter by modelling the key electromagnetic quantities as functions of the torque and speed based on offline parameter extraction from two-dimensional electromagnetic finite element analysis.The proposed electro-thermally coupled models,which are computationally efficient,are integrated into HVAC thermofluid simulation.Comparative studies of three heat pump-based HVAC architectures(conventional ambient heat only,waste heat only,and dual heat source)are performed using the proposed electro-thermally coupled models.The dual heat source HVAC architecture exhibits superior thermal performance over its counterparts in cold weather conditions.

Heat and mass transfer through spiral tubes in absorber of absorption heat pump system for waste heat recovery

Heat and mass transfer of a LiBr/water absorption heat pump system(AHP)was experimentally studied during working a heating-up mode.The examination was performed for a single spiral tube,which was simulated for heat transfer tubes in an absorber.The inside and outside of the tube were subjected to a film flow of the absorption liquid and exposed to the atmosphere,respectively.The maximum temperature of the absorption liquid was observed not at the entrance but in the region a little downward from the entrance in the tube.The steam absorption convective heat transfer coefficient between the liquid film flowing down and the inside wall of the temperature and the film temperature at the maximum temperature location and the bottom.The film heat and mass transfer coefficients rose with increasing Reynolds number of the liquid film stream.The coefficients showed opposite trend to the empirical correlation reported for laminar film flow on a straight smooth tube in a refrigeration mode in the past work.The fact can be caused due to a turbulent promotion effect of the liquid in a spiral tube.

The heat recovery simulation in the system of dry granulation of the steel slag

In present,the wet-based pattern is mainly adopted to deal with the steel slag by steel plant at home and abroad,the wet-based technology has some defects;Wasting of water,pollution of the environment,and the slag has not been fully recycled.This paper presents a new method,which is aimed to realize dry granulation,waste heat recovery and comprehensive utilizing the steel slag.According to the ideas of wind quenching granulation,the heating slag from the converter furnace,was bring to the granulation heat exchange system,through the process of breaking in a container,the granulation heat exchange system has the functions of feeding continuously and heat exchange.The heat air,through the diversion tubes,could be recycled in removing the dust.The granulation slag could be bring to a confined roller,granulating and cooling secondarily.The roller export was connected to a magnetic separator.The separated iron could be recycled,and the remaining slag could also be reused as building materials,in process of stabilization and secondary magnetic separation.The heated air could be guided into the boiler to generate the steam,which can be used to generate electricity,or use as cleaned energy,realizing the target to recycle the waste heat in steel slag.The highlights of the new method are dry granulation and waste heat recovery.This paper states the process of heat exchange between the air and the steel slag in the system of granulation heat exchange in the new technical process.In theory,it has been proved reasonable with the the system of granulation heat exchange,and also the work conditions has been optimized.

Transforming Waste Heat into“Renewable Heat”

Introduction:The current worldwide electric power&heat&cool production has a negative impact on the environment by emissions and enormous leaks of low-potential waste heat.Transformation of unused industrial low power heat into“renewable heat”useful to enhance the efficiency of the system is essential and actual innovation in the field of worldwide environmental protection.By introducing and defining the terminology of low-potential,“renewable”,“green heat”has created a new,parallel category of research in the energy sector.Traditional co-generation systems produce heat for space heating and hot water and generate electricity.Moving to tri-generation allows growing demand for air conditioning for homes,offices and commercial spaces such as server rooms and switchboards to be met simultaneously or on a seasonal basis.Tri-generation,or combined cooling,heat and power,is the process by which some of the heat produced by a co-generation plant is used to generate chilled water for air conditioning or refrigeration.Usually an absorption chiller is linked to the plant to provide this functionality.The technical solution is related to the new efficient manner and system of simultaneous generation of heat/cold from multiple heat sources,which has not yet been known,but in practice required.New system also enables advantageous utilization of solar power in supporting of the cooling output.The innovative system can be operated also within the existing central heating distribution systems.

Experiment Study on the Exhaust-Gas Heat Exchanger for Small and Medium-Sized Marine Diesel Engine

This paper aims to design a special exchanger to recover the exhaust gas heat of marine diesel engines used in small and medium-sized fishing vessels,which can then be used to heat water up to 55°C–85°C for membrane desalination devices to produce fresh water.A new exhaust-gas heat exchanger of fins and tube,with a reinforced heat transfer tube section,unequal spacing fins,a mixing zone between the fin groups and four routes tube bundle,was designed.Numerical simulations were also used to provide reference information for structural design.Experiments were carried out for exhaust gas waste heat recovery from a marine diesel engine in an engine test bench utilizing the heat exchanger.The experimental results show that the difference between heat absorption by water and heat reduction of exhaust gas is less than 6.5%.After the water flow rate was adjusted,the exhaust gas waste heat recovery efficiency was higher than 70%,and the exhaust-gas heat exchanger’s outlet water temperature was 55°C–85°C at different engine loads.This means that the heat recovery from the exhaust gas of a marine diesel engine meets the requirement to drive a membrane desalination device to produce fresh water for fishers working in small and medium-sized fishing vessels.

Characteristics of gaseous product from municipal solid waste gasification with hot blast furnace slag

Possibility of combustible gas production from municipal solid waste （MSW） using hot blast furnace （BF） slag has been studied.The objective of this work is to generate combustible gas from MSW using heated BF slag.In this experiment,the thermal stability of the MSW was analyzed by thermogravimetric analysis,and effects of temperature,gasifying agent （air,N2,steam） and BF slag on the gas products were investigated at 600？900 ？C.The thermogravimetric analysis indicates that the weight loss of MSW includes four stages：evaporation of the moisture,combustion of volatile materials,burning of carbon residue and burnout of ash.The contents of the combustible gas increase with increasing temperature,and the lower calorific value （LCV） increases rapidly at 600？900 ？C.It is found that volume fraction of CO,H2 and CH4 at different atmospheres increases in the order N2〈air〈steam.It is believed that BF slag acts as the catalyst and the heat carrier,which promotes the gasification reactivity of MSW.

A review on current development of thermophotovoltaic technology in heat recovery

The burning of fossil fuels in industry results in significant carbon emissions,and the heat generated is often not fully utilized.For high-temperature industries,thermophotovoltaics(TPVs)is an effective method for waste heat recovery.This review covers two aspects of high-efficiency TPV systems and industrial waste heat applications.At the system level,representative results of TPV complete the systems,while selective emitters and photovoltaic cells in the last decade are compiled.The key points of components to improve the energy conversion efficiency are further analyzed,and the related micro/nano-fabrication methods are introduced.At the application level,the feasibility of TPV applications in high-temperature industries is shown from the world waste heat utilization situation.The potential of TPV in waste heat recovery and carbon neutrality is illustrated with the steel industry as an example.