Prediction of the amount of urban waste solids by applying a gray theoretical model

Urban waste solids are now becoming one of the most crucial environmental problems. There are several different kinds of technologies normally used for waste solids disposal, among which landfill is more favorable in China than others, especially for urban waste solids. Most of the design works up to now are based on a roughly estimation of the amount of urban waste solids without any theoretical support, which lead to a series problems. To meet the basic information requirements for the design work, the amount of the urban waste solids was predicted in this research by applying the gray theoretical model GM (1,1) through non linear differential equation simulation. The model parameters were estimated with the least square method (LSM) by running a certain MATALAB program, and the hypothesis test results show that the residual between the prediction value and the actual value approximately comply with the normal distribution N (0,0 21 2), and the probability of the residual within the range (-0 17, 0 19) is more than 95%, which indicate obviously that the model can be well used for the prediction of the amount of waste solids and those had been already testified by the latest two years data about the urban waste solids from Loudi City of China. With this model, the predicted amount of the waste solids produced in Loudi City in the next 30 years is 8049000 ton in total.

Microstructural analysis of marl stabilized with municipal solid waste and nano-MgO

Municipal solid waste(MSW)is accumulating over elapsed time across the world,and it is observed in many projects associated with weak soils,such as marl.Therefore,effective solutions to the environmental problem are essential.Conventional techniques for stabilizing marl generally use substances such as lime and cement,which could exacerbate pollution.For this,some new stabilizers,e.g.nano-MgO,are used.There are large quantities of marls and MSW in Shiraz City,Iran.The present study aims to evaluate the feasibility of using nano-MgO as a green low-carbon binder to remove MSW from the environment and make construction projects more cost-effective.Consolidated drained shear tests were conducted to evaluate the mechanical behaviors of the nano-MgO treated marl specimens at high normal stresses.The marl specimens containing MSW percentages of 15%,25%,35%,and 45%and nano-MgO percentages of 0.25%,0.5%,0.75%,and 1%,were used.It is found that the marl containing 15%and 25%MSW and 0.5%nano-MgO at 28-d curing can perform cation exchange and form new cementitious products.The soils with merely MSW show good performance due to the removal of the kaolinite and the formation of brucite.However,the soil with 25%MSW and 0.5%nano-MgO shows the same strength enhancement as the specimen with the optimal nano-MgO(0.75%)through the formation of dolomite,with a 20.59%increase in strain energy(SE).

Effects of Using Municipal Solid Waste Incineration Tailings as Lightweight Aggregate on the Mechanical Properties of Specified Density Concrete

Municipal solid waste incineration tailings were used as lightweight aggregate(MSWIT-LA)in the preparation of specified density concrete to study the effects on compressive strength,axial compressive strength,flexural strength,microhardness,total number of pores,pore area,and pore spacing.The results showed that the internal curing and morphological effects induced by an appropriate quantity of MSWIT-LA improved the compressive response of specified density concrete specimens,whereas an excessive quantity of MSWIT-LA significantly reduced their mechanical properties.An analysis of pore structure indicated that the addition of MSWIT-LA increased the total quantity of pores and promoted cement hydration,resulting in a denser microstructure than that of ordinary concrete.The results of a principal component analysis showed that the mechanical response of specified density concrete prepared with 25%MSWIT-LA was superior to that of an equivalent ordinary concrete.It was therefore concluded that MSWIT-LA can be feasibly applied to achieve excellent specified density concrete properties while utilising municipal solid waste incineration tailings to protect the environment and alleviate shortages of sand and gravel resources.

CO_(2) mineralization by typical industrial solid wastes for preparing ultrafine CaCO_(3): A review

Mineral carbonation is a promising CO_(2) sequestration strategy that can utilize industrial wastes to convert CO_(2) into high-value CaCO_(3).This review summarizes the advancements in CO_(2) mineralization using typical industrial wastes to prepare ultrafine CaCO_(3).This work surveys the mechanisms of CO_(2) mineralization using these wastes and its capacities to synthesize CaCO_(3),evaluates the effects of carbonation pathways and operating parameters on the preparation of CaCO_(3),analyzes the current industrial application status and economics of this technology.Due to the large amount of impurities in solid wastes,the purity of CaCO_(3) prepared by indirect methods is greater than that prepared by direct methods.Crystalline CaCO_(3) includes three polymorphs.The polymorph of CaCO_(3) synthesized by carbonation process is determined the combined effects of various factors.These parameters essentially impact the nucleation and growth of CaCO_(3) by altering the CO_(2) supersaturation in the reaction system and the surface energy of CaCO_(3) grains.Increasing the initial pH of the solution and the CO_(2)flow rate favors the formation of vaterite,but calcite is formed under excessively high pH.Vaterite formation is favored at lower temperatures and residence time.With increased temperature and prolonged residence time,it passes through aragonite metastable phase and eventually transforms into calcite.Moreover,polymorph modifiers can decrease the surface energy of CaCO_(3) grains,facilitating the synthesis of vaterite.However,the large-scale application of this technology still faces many problems,including high costs,high energy consumption,low calcium leaching rate,low carbonation efficiency,and low product yield.Therefore,it is necessary to investigate ways to accelerate carbonation,optimize operating parameters,develop cost-effective agents,and understand the kinetics of CaCO_(3) nucleation and crystallization to obtain products with specific crystal forms.Furthermore,more studies on life cycle assessment(LCA)should be conducted to fully confirm the feasibility of the developed technologies.

The Application of Solid Waste in Thermal Insulation Materials: A Review

As socioeconomic development continues,the issue of building energy consumption has attracted significant attention,and improving the thermal insulation performance of buildings has become a crucial strategic measure.Simultaneously,the application of solid waste in insulation materials has also become a hot topic.This paper reviews the sources and classifications of solid waste,focusing on research progress in its application as insulation materials in the domains of daily life,agriculture,and industry.The research shows that incorporating household solid waste materials,such as waste glass,paper,and clothing scraps into cementitious thermal insulation can significantly reduce the thermal conductivity of the materials,leading to excellent thermal insulation properties.Insulation materials prepared from agricultural solid waste,such as barley straw,corn stalk,chicken feather,and date palm fibers,possess characteristics of lightweight and strong thermal insulation.Industrial solid waste,including waste tires,iron tailings,and coal bottom ash,can also be utilized in the preparation of insulation materials.These innovative applications not only have positive environmental significance by reducing waste emissions and resource consumption,but also provide efficient and sustainable insulation solutions for the construction industry.However,to further optimize the mix design and enhance the durability of insulation materials,continuous research is required to investigate the mechanisms through which solid waste impacts the performance of insulation materials.

Bird’s-eye view of recycled solid wastes in road engineering

Recent trends in road engineering have explored the potential of incorporating recycled solid wastes into infrastructures that including pavements,bridges,tunnels,and accessory structures.The utilization of solid wastes is expected to offer sustainable solutions to waste recycling while enhancing the performance of roads.This review provides an extensive analysis of the recycling of three main types of solid wastes for road engineering purposes:industrial solid waste,infrastructure solid waste,and municipal life solid waste.Industrial solid wastes suitable for road engineering generally include coal gangue,fly ash,blast furnace slag,silica fume,and steel slag,etc.Infrastructure solid wastes recycled in road engineering primarily consist of construction&demolition waste,reclaimed asphalt pavements,and recycled cement concrete.Furthermore,recent exploration has extended to the utilization of municipal life solid wastes,such as incinerated bottom ash,glass waste,electronics waste,plastic waste,and rubber waste in road engineering applications.These recycled solid wastes are categorized into solid waste aggregates,solid waste cements,and solid waste fillers,each playing distinct roles in road infrastructure.Roles of solid waste acting aggregates,cements,and fillers in road infrastructures were fully investigated,including their pozzolanic properties,integration effects to virgin materials,modification or enhancement solutions,engineering performances.Utilization of these materials not only addresses the challenge of waste management but also offers environmental benefits aiming carbon neutral and contributes to sustainable infrastructure development.However,challenges such as variability in material properties,environmental impact mitigation,secondary pollution to environment by leaching,and concerns regarding long-term performance need to be further addressed.Despite these challenges,the recycled solid wastes hold immense potential in revolutionizing road construction practices and fostering environmental stewardship.This review delves into a bird’seye view of the utilization of recycled solid wastes in road engineering,highlighting advances,benefits,challenges,and future prospects.

Household Solid Waste Awareness and Practices among Residents of Windhoek, Namibia

This study explores household solid waste management (HSWM) practices and awareness among residents of Windhoek West, a rapidly urbanizing constituency in the Khomas Region of Namibia. Employing a descriptive methodology, the research investigates the interplay between public awareness, regulatory frameworks, and the availability of waste management facilities to assess their impact on waste management behaviors. Our findings indicate significant gaps in both knowledge and infrastructure that hinder effective waste management. The study reveals that while there is a high willingness among residents to engage in recycling and waste reduction, actual practices are limited due to inadequate facilities and lack of stringent enforcement of waste policies. This research identifies key factors that influence waste management practices, including demographic characteristics and access to waste management facilities. It also proposes actionable strategies such as expanding recycling and sorting facilities, enhancing educational campaigns tailored to local needs, and implementing regular enforcement mechanisms. These strategies are aimed at improving compliance with waste management protocols and fostering a culture of environmental responsibility. The results of this investigation show the critical role of ongoing education and infrastructural improvement in bridging existing knowledge gaps and facilitating effective waste management practices. This research lays a foundational step toward enhancing sustainable urban development and effective waste management in Windhoek, providing valuable insights for policymakers, community leaders, and stakeholders engaged in urban environmental management.

The Impact of Solid Waste Generation, Storage and Separation Practices among Households on the Environment in Freetown

As urbanization and population growth continue to increase in Freetown, due to changes in economic, social, environmental, political, and demographic factors, the municipal solid waste (MSW) generation also continues to increase, making its management difficult for the municipal authority. Efficient separation and storage of solid waste at the source of generation can boost resource and energy recovery from MSW. This study examines the municipal solid waste management (MSWM) process, focusing on generation, storage and separation practices among households and their impact on the environment in Freetown. It emphasizes the inclusion of MSWM programs in primary schools to raise public awareness, the implementation of effective waste management practices, and the enforcement of related policies to enhance the MSWM sector, contributing to sustainable MSWM in Freetown. By utilizing both qualitative and quantitative methods, 393 structured questionnaires were administered across three selected sections to collect data on household solid waste storage and separation practices. The analysis employed descriptive statistics, using Origin-Pro9 and MS Excel. The findings show that with a population of 1.53 million people in Freetown, the per capita solid waste generation is 0.58 kg per day. The findings also show that 97% of the households have storage facilities as a result of the increase in awareness and education about the proper storage of solid waste. However, 96% of respondents do not practice separation of solid waste at the source of generation, which has become a concern among researchers in Sierra Leone. Additionally, 88% of respondents are unaware of ISWM principles, with only 12% aware, most of whom have received some education on proper solid waste management. The study recommends improving MSWM in Freetown to protect public health and the environment.

Assessment of the Characteristics of the Municipal Solid Waste Compost in Lebanon

Waste management is crucial due to the fast increase of human population, causing an increase in solid waste generation which if not properly managed causes environmental problems. Around 57% of the wastes generated from homes are made up of green material (fruits, vegetables…). Thus, reusing and recycling green wastes through composting is one way of reducing the waste load to landfills. Composting is the transformation of raw organic materials into organic soil amendments that provide nutrients to crops and enhance the tilth, fertility, and productivity of soils. Aerobic windrow composting system at Sukomi Greensite facility located at Karantina is performed, where materials biodegrade under controlled conditions to produce compost. However, assessment of the quality of the compost is fundamental in order to determine its usages. Thus, regular testing of physical, chemical and biological parameters was performed for adequate monitoring purposes. The basic objective of this study was to determine the characteristics of the Lebanese municipal solid waste compost on a yearly basis and compare these characteristics amongst the years. Hence, each parameter was tested and compared to the BNQ international Canadian standards for proper classification of the compost and adequate identification of its usages. The preliminary data obtained were statistically diagnosed through principal component analysis by Spadv55 software. All the data reflected the normal content value of the studied parameters with minor differences between the years except for year 2007 which demonstrated higher levels of Potassium, Phosphate, Lead and Cadmium. The characteristics of the compost enabled it to be used as a soil amendment on all types of agricultural and landscape commodities at the adequate dosages and proper timing. This data will additionally reflect the efficiency of the solid waste management practices adopted via highlighting the importance of the implementation of the integrated solid waste management practices.

Solid Waste Sector Tested by Stakeholder Dynamics in Koudougou (Burkina Faso)

Solid waste management is one of the major concerns of the authorities in the town of Koudougou. The town’s dynamic is reflected in relative demographic growth and consumption patterns that are conducive to the formation of landfill sites. These landfills are the source of numerous environmental consequences and risk factors for local residents. The aim of this article is to analyze the dysfunctions in the solid waste sector caused by the interplay of actors. It draws on secondary data from the state of the art on the subject and primary data collected from 305 households and 89 actors in the sector between September 2022 and March 2023, as part of an ongoing thesis. These data show that the interplay of actors contributes to the malfunctioning of pre-collection and secondary collection, and remains a factor in the proliferation of illegal dumpsites.

Current Situation Analysis and Suggestions for Solid Waste Management Practices among Households in Freetown

Freetown which is the capital city of Sierra Leone is facing challenges with population growth, urbanization, and industrialization, leading to an increase in municipal solid waste (MSW) generation. The study aims to evaluate MSW generation, composition, and disposal methods, as well as the impact of collection fees, policy implementation, and women’s participation in municipal solid waste management (MSWM). The study used both qualitative and quantitative methods for data collection and analysis. The study administered 393 structured questionnaires in three selected sections to collect data on variables such as family size, education, level of knowledge, etc. The study used door-to-door data collection to determine the rate of solid waste generation, composition, and disposal in 66 households from two of the selected sections and 34 households from the other section to evaluate the current situation of MSWM practices among households in Freetown. The study used a descriptive statistic to analyze the data collected using Origin-Pro9 and MS Excel software. The findings showed that with a 4.2% urban growth rate, Freetown had a population of 1,467,543 in 2023, generating 851 tons of MSW per day, with organic waste accounting for 78% of the total MSW generated. Plastic waste generation also increased from 7.6% in 2020 to 13% in 2023. The study emphasizes the need to sustain the MSWM system by prioritizing solid waste collection fees, policy enforcement, and women’s participation in the MSWM sector. It further suggests and provides recommendations for developing an efficient and sustainable MSWM system in Sierra Leone, including knowledge transfer from countries like China and the US.

Model Prediction and Optimal Control of Gas Oxygen Content for A Municipal Solid Waste Incineration Process

In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.

Production Practice of Solid Waste Desulfurizer Disposal in European Metallurgical Furnace

In order to realize the OY Smelting Furnace disposal of solid waste,municipal waste,form a model of steel enterprises and urban integration,through the production practice of smelting furnace,analyzes the mechanism of solid waste disposal,and proposed the disposal of solid waste desulfurization agent and disposal method:According to the theory to guide the actual production process,the test ton of iron with 10-15kg of desulfurizer in the production process does not affect the quality of molten iron and slag quality.

Assessment of Municipal Solid Waste Management in the Farmgate Area of Dhaka North City Corporation

This investigation is focused on conducting a thorough analysis of Municipal Solid Waste Management (MSWM). MSWM encompasses a range of interdisciplinary measures that govern the various stages involved in managing unwanted or non-utilizable solid materials, commonly known as rubbish, trash, junk, refuse, and garbage. These stages include generation, storage, collection, recycling, transportation, handling, disposal, and monitoring. The waste materials mentioned in this context exhibit a wide range of items, such as organic waste from food and vegetables, paper, plastic, polyethylene, iron, tin cans, deceased animals, byproducts from demolition activities, manure, and various other discarded materials. This study aims to provide insights into the possibilities of enhancing solid waste management in the Farmgate area of Dhaka North City Corporation (DNCC). To accomplish this objective, the research examines the conventional waste management methods employed in this area. It conducts extensive field surveys, collecting valuable data through interviews with local residents and key individuals involved in waste management, such as waste collectors, dealers, intermediate dealers, recyclers, and shopkeepers. The results indicate that significant amounts of distinct waste categories are produced daily. These include food and vegetable waste, which amount to 52.1 tons/day;polythene and plastic, which total 4.5 tons/day;metal and tin-can waste, which amounts to 1.4 tons/day;and paper waste, which totals 5.9 tons/day. This study highlights the significance of promoting environmental consciousness to effectively shape the attitudes of urban residents toward waste disposal and management. It emphasizes the need for collaboration between authorities and researchers to improve the current waste management system.

Modeling Solid Waste Minimization Performance at Source in Dar es Salaam City, Tanzania

Municipal solid waste generation is strongly linked to rising human population and expanding urban areas, with significant implications on urban metabolism as well as space and place values redefinition. Effective management performance of municipal solid waste management underscores the interdisciplinarity strategies. Such knowledge and skills are paramount to uncover the sources of waste generation as well as means of waste storage, collection, recycling, transportation, handling/treatment, disposal, and monitoring. This study was conducted in Dar es Salaam city. Driven by the curiosity model of the solid waste minimization performance at source, study data was collected using focus group discussion techniques to ward-level local government officers, which was triangulated with literature and documentary review. The main themes of the FGD were situational factors (SFA) and local government by-laws (LGBY). In the FGD session, sub-themes of SFA tricked to understand how MSW minimization is related to the presence and effect of services such as land use planning, availability of landfills, solid waste transfer stations, material recovery facilities, incinerators, solid waste collection bins, solid waste trucks, solid waste management budget and solid waste collection agents. Similarly, FGD on LGBY was extended by sub-themes such as contents of the by-law, community awareness of the by-law, and by-law enforcement mechanisms. While data preparation applied an analytical hierarchy process, data analysis applied an ordinary least square (OLS) regression model for sub-criteria that explain SFA and LGBY;and OLS standard residues as variables into geographically weighted regression with a resolution of 241 × 241 meter in ArcMap v10.5. Results showed that situational factors and local government by-laws have a strong relationship with the rate of minimizing solid waste dumping in water bodies (local R square = 0.94).

Prediction of NO_(x)concentration using modular long short-term memory neural network for municipal solid waste incineration

Air pollution control poses a major problem in the implementation of municipal solid waste incineration(MSWI).Accurate prediction of nitrogen oxides(NO_(x))concentration plays an important role in efficient NO_(x)emission controlling.In this study,a modular long short-term memory(M-LSTM)network is developed to design an efficient prediction model for NO_(x)concentration.First,the fuzzy C means(FCM)algorithm is utilized to divide the task into several sub-tasks,aiming to realize the divide-and-conquer ability for complex task.Second,long short-term memory(LSTM)neural networks are applied to tackle corresponding sub-tasks,which can improve the prediction accuracy of the sub-networks.Third,a cooperative decision strategy is designed to guarantee the generalization performance during the testing or application stage.Finally,after being evaluated by a benchmark simulation,the proposed method is applied to a real MSWI process.And the experimental results demonstrate the considerable prediction ability of the M-LSTM network.

Comprehensive utilization of solid waste resources: Development of wet shotcrete for mines

The development of solid waste resources as constituent materials for wet shotcrete has significant economic and environmental advantages. In this study, the concept of using tailings as aggregate and fly ash and slag powder as auxiliary cementitious material is proposed and experiments are carried out by response surface methodology(RSM). Multivariate nonlinear response models are constructed to investigate the effect of factors on the uniaxial compressive strength(UCS) of tailings wet shotcrete(TWSC). The UCS of TWSC is predicted and optimized by constructing Gaussian process regression(GPR) and genetic algorithm(GA). The UCS of TWSC is gradually enhanced with the increase of slag powder dosage and fineness modulus, and it is enhanced first and then decreased with the increase of fly ash dosage. The microstructure of TWSC has the highest gray value and the highest UCS when the fly ash dosage is about 120 kg·m^(-3). The GPR–GA model constructed in this study achieves high accuracy prediction and optimization of the UCS of TWSC under multi-factor conditions.

Forecasting the Municipal Solid Waste Using GSO-XGBoost Model

Waste production rises in tandem with population growth and increased utilization.The indecorous disposal of waste paves the way for huge disaster named as climate change.The National Environment Agency(NEA)of Singapore oversees the sustainable management of waste across the country.The three main contributors to the solid waste of Singapore are paper and cardboard(P&C),plastic,and food scraps.Besides,they have a negligible rate of recycling.In this study,Machine Learning techniques were utilized to forecast the amount of garbage also known as waste audits.The waste audit would aid the authorities to plan their waste infrastructure.The applied models were k-nearest neighbors,Support Vector Regressor,ExtraTrees,CatBoost,and XGBoost.The XGBoost model with its default parameters performed better with a lower Mean Absolute Percentage Error(MAPE)of 8.3093(P&C waste),8.3217(plastic waste),and 6.9495(food waste).However,Grid Search Optimization(GSO)was used to enhance the parameters of the XGBoost model,increasing its effectiveness.Therefore,the optimized XGBoost algorithm performs the best for P&C,plastics,and food waste with MAPE of 4.9349,6.7967,and 5.9626,respectively.The proposed GSO-XGBoost model yields better results than the other employed models in predicting municipal solid waste.

Development of Wet Shotcrete with Solid Waste as Aggregate:Strength Optimization and Mix Proportion Design

The super-fine particle size of tailings is its drawback as a recycled resource,which is reflected in the low strength of the new construction and industrial materials formed when it is mixed with cement and other cementitious materials.Therefore,it is crucial to study the effect of tailings particle size and cementitious material on the strength of tailings wet shotcrete(TWSC)and to investigate the optimal mix proportion.In this paper,a multivariate nonlinear response model was constructed by conducting central composite experiments to investigate the effect of different factors on the strength of TWSC.The strength prediction and mix proportion optimization of TWSC are carried out by machine learning techniques.The results show that the response model has R^(2)>0.94 and P<0.01,which indicates that the model has high reliability.Moreover,the strength of TWSC increases with the increase of tailings fineness modulus and decrease of water-binder ratio,while it also increases and then decreases with the increase of replacement rate of slag powder to cement(SRC rate).The extreme learning machine(ELM)constructed in this paper predicts the strength of TWSC with an accuracy of more than 98%and achieves rapid prediction under multi-factor conditions.It is worth mentioning that the ELM combined with the genetic algorithm(ELM-GA)collaboratively solved to obtain the mix proportion for C15 and C20 strength grades of TWSC and the maximum error is verified by experiments to be less than 2%.

Spatio-Temporal Characteristics of Heat Transfer of Methanation in Fluidized Bed for Pyrolysis and Gasification Syngas of Organic Solid Waste

Methanation is an effective way to efficiently utilize product gas generated from the pyrolysis and gasification of organic solid wastes.To deeply study the heat transfer and mass transfer mechanisms in the reactor,a successful three-dimensional comprehensive model has been established.Multiphase flow behavior and heat transfer mechanisms were investigated under reference working conditions.Temperature is determined by the heat release of the reaction and the heat transfer of the gas-solid flow.The maximum temperature can reach 951 K where the catalyst gathers.In the simulation,changes in the gas inlet velocity and catalyst flow rate were made to explore their effects on CO conversion rate and temperature for optimization purposes.As the inlet gas velocity increases from 2.78 to 4.79 m/s,the CO conversion rate decreases from 81.6%to 72.4%.However,more heat is removed from the reactor,and the temperature rise increases from 78.03 to 113.49 K.When the catalyst flow rate is increased from 7.18 to 17.96 kg/(m^(2)·s),the mass of the catalyst in the reactor is increased from 0.0019 to 0.0042 kg,and the CO conversion rate is increased from 66.8%to 81.5%.However,this increases the maximum temperature in the reactor from 940.0 to 966.4 K.