Preparation and Swelling Kinetic Analysis of Poly (HPMC-co-AA-co-AM) Super Absorbent Resin

Super absorbent resin(SAR)is prepared by aqueous high temperature polymerization using hydroxypropyl methylcellulose(HPMC)as monomer backbone material,acrylic acid(AA)and acrylamide(AM)as the graft copolymer monomer,potassium persulfate(KPS)as the initiator to generate free radicals,and N,N`-methylenebisacrylamide(MBA)as cross-linking agent for cross-linking reaction.Simutaneously,the influence of individual factors on the water absorption is investigated,and these factors are mainly AA,AM,KPS,MBA,HPMC,and reaction temperature.The optimized conditions are obtained by the experiment repeating for several times.The water absorption multiplicity and salt absorption multiplicity under the conditions are 782.4 and 132.5 g/g,respectivity.Furthermore,the effects of different temperatures and salt concentrations on its water absorption,as well as the swelling kinetics of SAR are studied.It is indicated the water-absorbing swelling process is mainly caused by the difference in water osmotic pressure and Na+concentration inside and outside the cross-linked molecular structure of the resin,which is not only consistent with the quasi-secondary kinetic model,but also with the Fick diffusion model.

Microwave absorption and thermal properties of coral-like SiC aerogel composites prepared by water glass as a silicon source

As a heat-resistant wave-absorbing material,silicon carbide(SiC)aerogel has become a research hotspot at present.However,the most common silicon sources are organosilanes,which are costly and toxic.In this work,SiC aerogels were successfully prepared by using water glass as the silicon source.Specifically,the microstructure and chemical composition of SiC aerogels were controlled by adjusting the Si to C molar ratio during the sol–gel process,and the effect on SiC aerogel microwave absorption properties was investigated.The SiC aerogels prepared with Si:C molar ratio of 1:1 have an effective electromagnetic wave absorption capacity,with a minimum reflection loss value of-46.30 dB at 12.88 GHz and an effective frequency bandwidth of 4.02 GHz.They also have good physical properties,such as the density of0.0444 g/cm^(3),the thermal conductivity of 0.0621 W/(m·K),and the specific surface area of 1099 m^(2)/g.These lightweight composites with microwave-absorbing properties and low thermal conductivity can be used as thermal protection materials for space shuttles and reusable carriers.

Assessment of Super Absorbent Polymer (SAP) on Plant Available Water (PAW) in Dry Lands

One of the ways of overcoming the cost of irrigation is through in-situ water harvesting at the plant roots. Super absorbent polymer (SAP) can facilitate water harvesting at the plant roots. This study attempted to assess the effect of SAP on plant available water (PAW) of different soils. In this study, SAP was sequentially added at the rate of 0.2%, 0.3% and 0.5% of the soil weight and its impact assessed in clay, sandy clay and sandy loam soils. The moisture retention characteristics of the original and SAP treated soils were studied using soil water retention curves (SWRC) and results modelled using Gardner model. PAW was estimated from SWRC as the difference between moisture content at 1.5 and 3 bar in all soils. The difference in PAW between original and treated soils was assessed at 5% level of significance. The WRC of all the samples was adequately found to be described by the Gardner model (Coefficient of determination R2 ≥ 98% and residual standard error (RSE) ≤ 0.04). SWRC changed with increase in SAP percentage in clay, sandy clay and sandy loam soils. Clay had a higher change in water retention then sandy clay and lastly sandy loam. Plant available water content (PAW) in all soils increased. In clay soil it increased with increase in SAP from 0.3291 at zero SAP to 0.6223 at 0.5% SAP. Sandy clay soil increased in PAW from 0.2721 at zero SAP to 0.5335 at 0.5% SAP and Sandy loam soils from 0.1691 at zero SAP to 0.3461 at 0.5% SAP. Hence, from the study SAP can be used to conserve irrigation water in the plant roots and therefore reducing the cost since PAW has been increased.

Characteristics and Performance of Novel Water-Absorbent Slow Release Nitrogen Fertilizers

In this article, a research on the characteristics and performance of water-absorbent slow release nitrogen fertilizer （WASRNF） using infrared spectroscopy （IR）, scanning electronic microscopy （SEM）, differential scanning calorimetry （DSC）, and thermogravimetry analysis （TGA）, was present. The results indicate that the water absorbency and nitrogen analysis of WASRNF is 103 g g^-1 and 30%, respectively, and WASRNF exhibits approximately neutral pH and very low salt index. WASRNF is a copolymer of nitrogen fertilizer and super absorbent polymer （SAP） monomers which is formed through hydrogen bond interaction, and the molecule contains hydrophilic groups, which is responsible for the absorption and water retention capacity of the molecule. WASRNF is a gel that exhibits the ability to swell, but does not dissolve in water. WASRNF shows non-homogenous nature as a whole, but in local zone it is homogenous, the copolymer molecule shows chain network that is the physical structure responsible for absorption and retention of water in WASRNF. The water retained in WASRNF exists as free and nonfreezing bound and freezing bound water states, with the free and the nonfreezing water accounting for more than 95% of water retained in WASRNF, and the nonfreezing bound water for less than 5%. WASRNF functions in delaying the release of nitrogen from it, thereby serving a novel slow release nitrogenous fertilizer.

改性方法对玉米秸秆纤维素-腐植酸基吸水树脂性能的影响

分别采用等离子体和紫外固化法对玉米秸秆纤维素-腐植酸基吸水树脂(CS-HA-PAA)进行改性,通过傅里叶变换红外光谱仪和扫描电子显微镜对改性吸水树脂的结构和形貌进行表征,考察了改性吸水树脂的耐盐性、耐酸碱性、保水性、反复吸液性等性能。结果表明:改性后CS-HA-PAA亲水基团增多,表面粗糙且产生孔洞结构,有利于提高吸水性能;采用最佳工艺条件制备的等离子体改性CS-HA-PAA和紫外固化改性CS-HA-PAA的吸水率分别可达1053.2g/g、869.44g/g,NaCl质量浓度为9g/L时最高吸盐水率分别为181.03g/g、151.49g/g,等离子体改性CS-HA-PAA的吸水、耐盐性能优于紫外固化法改性CS-HA-PAA。

Influence of Suspension Parameters on Water Absorbency of Starch-poly(sodium acrylate) Synthesized by Inverse Suspension Polymerization

Superabsorbents starch grafted sodium polyacrylate was prepared by inverse suspension polymerization, using toluene as the continuous phase, potassiun persulfate as the initiator. The effect of suspension parameters, such as volume ratio of continuous phase and dispersed phase,type and dosage of suspending agents, on water absorbency of the starch grafted polymer was studied.Different starch derivatives were also investigated.Superabsorbents made of cationic starch has higher water absorbency than that made of native corn starch.

Recent progress and future prospects of oil-absorbing materials

Oil and organic solvent contamination, derived from oil spills and organic solvent leakage, has been recognized as one of the major environmental issues imposing a serious threat to both human and ecosystem health. Among the various presented technologies applied for oil/water separation, oil absorption process has been explored widely and offers satisfactory results especially with surface modified oil-absorbing material and/or hybrid absorbents. In this review, we summarize the recent research activities involved in the designing strategies of oil-absorbing absorbents and their application in oil absorption. Then, an extensive list of various oil-absorbing materials from literature, including polymer materials, porous inorganic materials and biomass materials, has been compiled and the oil adsorption capacities toward various types of oils and organic solvents as available in the literature are presented along with highlighting and discussing the various factors involved in the designing of oil-absorbing absorbents tested so far for oil/water separation. Finally, some future trends and perspectives in oil-absorbing material are outlined.

Preparation of Liquor Flavoring from Yellow Water Based on Water Absorbent Resin

[Objective] This study was conducted to extract the scarce natural liquor flavorings desired by many liquor factories from yellow water. [Method] Strong water absorbent resin was used to absorb moisture from the yellow water in order to concentrate it into dense yellow water at first, followed by azcotropic dis- tillation of the previously concentrated yellow water, and then, catalytic esterification was performed to the remaining liquid after the distillation. [ Results] The 7. 066 7 fractions of concentrated yellow water with 56.7% ethanol could be obtained after the treatment of 100 fractions of yellow water with strong water absorbent resin. Azeotrope of 0.432 8 fraction of natural acetaldehyde, 0. 269 4 fraction of ethyl formate and methyl alcohol, 0. 975 0 fraction of ethyl acetate and methyl alco- hol could be obtained after the azeotropic distillation per 100 fractions of concentrated yellow water. After the addition of CaC12, O. 220 7 fraction of ethyl formate and 0. 514 2 fraction of ethyl acetate could be obtained after distillation of the azeotrope. Finally, 92. 094 8 fractions of esterification liquid with 38 kinds of flavor- ing compound could be obtained after catalytic esterification of 100 fractions of concentrated yellow water, and the content of ethyl acetate, ethyl propionate, ethyl- butyrate, ethyl valerate, ethyl lactate and ethyl bexanoate were as much as 142.9, 22.2, 54.2, 3.3,75.4 and 158.9 g/L, respectively. [ Conclusion] Top-grade Luzhou-flavor liquor could be made by mixing 6.5 fractions of common liquor with acetaldehyde, ethyl formate, ethyl acetate and esterification liquid which were ob- tained from 1 fraction of yellow water. Therefore, the yellow water has a great recycling value, and it tells us that the technique of extracting liquor flavorings from yellow water has tremendous market value.

Micro- and nanoporous materials capable of absorbing solvents and oils reversibly： the state of the art

Treatment of petroleum spills and organic solvent pollution in general is an important issue; several techniques are under development to remove oil from water. The use of absorbents is one of the most common techniques to tackle this problem. These absorbents can be classified based on their characteristics of recyclability into irreversible and reversible ones. In this review, we discuss the application of several materials as oil absorbents, according to their classification and characteristics such as hydrophobicity, surface area and oil absorption capacity. Also, the fabrication methods for some materials are presented and analyzed.

Three-dimensional hydrodynamic model of Xiamen waters

A semi-implicit and Eulerian - Lagrangian finite difference method for three-dimensionalshallow flow has been extended to a more complete system of equations incorporating second-moment turbulence closure model and transport equations of salinity and temperature. The simulation for flooding and drying of mudflats has been improved. The model is applied to Xiamen waters. Based on extensive survey data, water level elevation, temperature and salinity field along the eastern open boundary and at the Jiulong River inlets and runoffs are analyzed, specified and calibrated. The computed results show good agreement with the measured data, reproduce flooding, emergence of large and complex mudflat region.

The diffusive fluxes of inorganic nitrogen across the intertidal sediment-water interface of the Changjiang Estuary in China

Ammonium and nitrate concentrations were analyzed in near-bottom water and pore water collected from ten stations of the intertidal flat of the Changjiang Estuary during April, July, November and February. The magnitudes of the benthic exchange fluxes were determined on the basis of concentration gradients of ammonium and nitrate at the near-bottom water and interstitial water interface in combination with calculations of a modified Fick＇ s first law. Ammonium fluxes varied from - 5.05 to 1.43 μg/（ cm^2·d） and were greatly regulated by the production of ammonium in surface sediments, while nitrate fluxes ranged from - 0. 38 to 1.36 μg/ （ cm^2·d） and were dominated by nitrate concentrations in the tidal water. It was found that ammonium was mainly released from sediments into water columns at most of stations whereas nitrate was mostly diffused from overlying waters to intertidal sediments. In total, 823.75 t/a ammonium-N was passed from intertidal sediments to water while about 521.90 t/a nitrate-N was removed from overlying waters to intertidal sediments. This suggests that intertidal sediments had the significant influence on modulating inorganic nitrogen in the tidal water.

Application of sustainable basil seed as an eco-friendly multifunctional additive for water-based drilling fluids

Basil seed,containing anionic heteropolysaccharides in its outer pericarp,swells as gelatinous hydrocolloid when soaked in water.In this study,basil seed powder(BSP)was used as a multifunctional additive for water-based drilling fluids.The chemical composition,water absorbency,rheological properties of aqueous suspension of BSP were tested.The effect of BSP on the rheological and filtration of bentonitebased drilling fluid before and after thermal aging was investigated.The inhibition characteristics were evaluated by linear swelling,shale cuttings dispersion and shale immersion test.Lubricity improvement by BSP was measured with extreme pressure lubricity test.The results revealed that incorporation of BSP into bentonite suspension improved rheological and filtration properties effectively after thermal aging of 120℃.BSP exhibited superior inhibitive capacity to xanthan and synergistic effect with KCl.BSP could reduce friction by forming hydration layer.The nanoscale three-dimensional network structures enable BSP to maintain high water retention and absorb strongly on bentonite and metal surface,contributing to enhanced rheology,filtration,inhibition and lubrication properties.The versatile characteristic of BSP,as well as biodegradation makes it a promising additive using in high performance water-based drilling fluid and a potential alternative to conventional synthetic polymers.

Using irrigation intervals to optimize water-use efficiency and maize yield in Xinjiang,northwest China

Worldwide, scarce water resources and substantial food demands require efficient water use and high yield.This study investigated whether irrigation frequency can be used to adjust soil moisture to increase grain yield and water use efficiency(WUE) of high-yield maize under conditions of mulching and drip irrigation.A field experiment was conducted using three irrigation intervals in 2016: 6, 9, and 12 days(labeled D6, D9, and D12) and five irrigation intervals in 2017: 3, 6, 9, 12, and 15 days(D3, D6, D9, D12, and D15).In Xinjiang, an optimal irrigation quota is 540 mm for high-yield maize.The D3, D6, D9, D12, and D15 irrigation intervals gave grain yields of 19.7, 19.1–21.0, 18.8–20.0, 18.2–19.2, and 17.2 Mg ha^-1 and a WUE of 2.48, 2.53–2.80, 2.47–2.63, 2.34–2.45, and 2.08 kg m-3, respectively.Treatment D6 led to the highest soil water storage, but evapotranspiration and soil-water evaporation were lower than other treatments.These results show that irrigation interval D6 can help maintain a favorable soil-moisture environment in the upper-60-cm soil layer, reduce soilwater evaporation and evapotranspiration, and produce the highest yield and WUE.In this arid region and in other regions with similar soil and climate conditions, a similar irrigation interval would thus be beneficial for adjusting soil moisture to increase maize yield and WUE under conditions of mulching and drip irrigation.

Layer regrouping for water-flooded commingled reservoirs at a high water-cut stage

Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to improve oil recovery for high water-cut multilayered reservoirs. Dif- ferent regroup scenarios may lead to different production performances. Based on unstable oil-water flow theory, a multilayer commingled reservoir simulator is established by modifying the production split method. Taking into account the differences of layer properties, including per- meability, oil viscosity, and remaining oil saturation, the pseudo flow resistance contrast is proposed to serve as a characteristic index of layer regrouping for high water-cut multilayered reservoirs. The production indices of multi- layered reservoirs with different pseudo flow resistances are predicted with the established model in which the data are taken from the Shengtuo Oilfield. Simulation results show that the pseudo flow resistance contrast should be less than 4 when the layer regrouping is implemented. The K-means clustering method, which is based on the objec- tive function, is used to automatically carry out the layer regrouping process according to pseudo flow resistances. The research result is applied to the IV-VI sand groups of the second member of the Shahejie Formation in the Shengtuo Oilfield, a favorable development performance is obtained, and the oil recovery is enhanced by 6.08 %.

The Coupling Coordination Evolution Research of Economy - Ecology - Society System in Xinjiang：Based on the Interaction Perspective of Water Resources

Under the water resources perspective,coupling coordination of economy-ecology-society system in Xinjiang was taken as the research object. By building the coupling evaluation index system of the water resources-economy-ecology-society system,quantitative evaluation and analysis of the coupling coordination of the water resources-economy-ecology-society system from 2001 to 2014 were conducted. The results showed that benefit indexes of economic system and social system grew rapidly,while benefit indexes of water resources system and ecosystem fluctuated smoothly from 2001 to 2014; coupling state of the whole system was at rival stage,and coupling coordination was reluctant coordination type,and the coupling index was slightly higher than the coupling coordination index. Moreover,it showed that the more the coupling systems,the lower indices of coupling and the coupling coordination.

Green-Naghdi Theory,Part A:Green-Naghdi(GN) Equations for Shallow Water Waves

In this work,Green-Naghdi (GN) equations with general weight functions were derived in a simple way. A wave-absorbing beach was also considered in the general GN equations. A numerical solution for a level higher than 4 was not feasible in the past with the original GN equations. The GN equations for shallow water waves were simplified here, which make the application of high level (higher than 4) equations feasible. The linear dispersion relationships of the first seven levels were presented. The accuracy of dispersion relationships increased as the level increased. Level 7 GN equations are capable of simulating waves out to wave number times depth . Numerical simulation of nonlinear water waves was performed by use of Level 5 and 7 GN equations, which will be presented in the next paper.

Water Hammer Model of Shock Absorber Throttle Slice

In allusion to easy invalidation of damping valve in vehicle shock absorber caused by the impact from the road surface, the importance of the study of damping valve water hammer pressure is presented. The physical model of damping valve with the circle throttle slice is established. The time for the throttle slice deformation is studied by using the finite software, and the laws that how the structure parameters affect the deformation time are obtained. Combining the theory of water hammer, the water hammer initial and boundary condition of the damping valve is deduced, and the water hammer model of throttle slice is established. The analysis of simulation results indicates that the water hammer pressure amplitude and the amount of water hammer oscillation period can be reduced and the dependability of the valve can be enhanced by modifying the structure parameters and aperture width between slice and valve body.

Coupling metal oxide nanoparticle catalysts for water oxidation to molecular light absorbers

Water oxidation, as a mandatory reaction of solar fuels conversion systems, requires the use of light absorbers with electronic properties that are well matched with those of the multi-electron catalyst in order to achieve high efficiency. Molecular light absorbers offer flexibility in fine tuning of orbital energetics,and metal oxide nanoparticles have emerged as robust oxygen evolving catalysts. Hence, these material choices offer a promising approach for the development of photocatalytic systems for water oxidation.However, efficient charge transfer coupling of molecular light absorbers and metal oxide nanoparticle catalysts has proven a challenge. Recent new approaches toward the efficient coupling of these components based on synthetic design improvements combined with direct spectroscopic observation and kinetic evaluation of charge transfer processes are discussed.

Influence of Reaction Parameters on Water Absorbency of Starch Grafted Superabsorbents

Superabsorbents starch grafted sodium polyacrylate was synthesized by inverse suspension polymerization, using toluene as the continuous phase, potassium persulfate as the initiator. The effect of reaction parameters, such as starch pretreatment temperature, neutralization degree of monomer, reaction time and temperature, concentration of initiator, molar ratio of monomer and starch, on water absorbency of the starch grafted polymer was studied. The effects of the last two parameters were investigated by uniform design method, and the prediction equation was obtained.

PRELIMINARY STUDIES ON STRUCTURES AND PROPERTIES OF WATER-RETENTIVE, FLAME-RETARDANT ACRYLIC FIBERS

The blend fibers of acrylonitrile-vinylidene chloride-sodium methallysulfonate copolymer(AN-VDC-SMAS) and cellulose acetate (CA) with various blend ratios were investigated bymeans of SEM, DDV, WAXD, etc. The results show that AN-VDC-SMAS and CA areincompatibale; the numerous microvoids in the blend fiber resulted from the phase seperationcan remarkably improve the water absorbability and the dyeing behavior but hardly influencethe mechanical properties. On the other hand, the crystal structure of the continuous phaseAN-VDC-SMAS is not influnced by the dispersed phase CA.