Study on corrosion behavior of heat exchanger in water source heat pump

Water source heat pump is a new kind of energy saving process.One of the most common problems for water source heat pump system is the corrosion of the copper in heat exchanger.The quality of water is the key factor.The river water collected in six different places of the Yangtze River and Jialing River in Chongqing were analyzed.Various parameters(pH,coexisted ions,and hardness value)were investigated.It showed that the Yangtze River and Jialing River water was suitable for developing water source heat pump technology.Further more,aimed at the temperature and pH of the raw water's variation range in a year,the corrosion behavior of copper material was studied by controlling the water environmental condition.Corrosion rate of copper is accelerated at high temperature and lower pH value.

Research on Performance of Ground-Source Heat Pump Double U Underground Pipe Heat Exchange

This paper uses FLUENT software building the three-dimensional unsteady state model of ground source heat pump single U and double U underground pipe to study on heat exchange of underground pipe system in the condition of unsteady state long-term continuous running, analyzes the change of soil temperature filed around underground pipe and performance of underground pipe heat exchange between single U and double U pipe system. The results show that double U pipe system is better than single U system, which can improve unit depth heat exchange efficiency, reduce the number of wells and reduce the initial investment.

Performance and Optimization of Air Source Heat Pump Water Heater with Cyclic Heating

A new type of microchannel condenser applied in the air source heat pump water heater(ASHPWH)with cyclic heating was proposed in this study.The operating performance of the ASHPWH was frst tested.Then,the structure of the microchannel condenser was optimized with the implement of vortex generators.Finally,a numerical model of the ASHPWH was established and the optimized microchannel condenser was studied.The experimental results showed that the average coefficient of performance(COP)of the 1HP(735 W)ASHPWH reached 3.48.In addition,the optimized microchannel condenser could be matched with a 3 HP(2430W)ASHPWH with an average heating capacity of 10.30 kW,and achieving an average COP of 4.24,14.6%higher than the limit value in the national standard.

中深层地埋管热泵供热系统运行特性实测研究

通过大量工程实测研究,总结了中深层地埋管热泵供热技术的运行特性。中深层地埋管具有出水温度高、取热功率大、长期运行稳定的特点,为热泵系统提供了高品位的低温热源,以提升其运行性能;同时中深层地埋管自身存在间歇蓄热特性,能很好地满足建筑供热需求变化与柔性用能;无级变频热泵机组更适合与中深层地埋管匹配运行,节能减排效果显著;热源侧水系统具有小流量、大扬程,且阻力随着流量变化而大幅度变化的特性。研究结果可为提升该技术的供热性能提供关键指导。

地下水源热泵回灌中大肠杆菌阻塞试验研究

以地下水源热泵回灌过程中大肠杆菌堵塞作为研究对象,通过自主研发的砂层颗粒迁移-沉积试验系统观察大肠杆菌在多孔介质孔隙孔道内的运移、沉积。分别以石英石、玻璃珠作为多孔介质做对比性试验,通过试验得出:石英石颗粒不均匀,级配不良,颗粒间的咬合力为大肠杆菌的沉积提供了“温床”,进而孔隙水压力呈现先增大后减小再稳定的状态;但玻璃珠颗粒粒径均匀,同时颗粒之间光滑,咬合力小,不利于大肠杆菌的沉积,孔隙水压力呈现陡减的现象。建立大肠杆菌渗透率衰减数学模型,将理论值和室内试验值进行数据拟合,从验证的结果看,所提渗透率衰减模型对预见微生物的迁移和沉积所引起的孔隙率减小是有效的。

水源热泵回灌中大肠杆菌阻塞迁移沉积特性参数试验研究

以地下水源热泵回灌过程中大肠杆菌堵塞作为研究对象,通过自主研发的砂层颗粒迁移-沉积试验系统观察大肠杆菌在多孔介质孔隙孔道内的运移、沉积。以3种不同长度的试验箱体开展大肠杆菌在多孔介质里的运移沉积规律,通过试验得出:1)石英石颗粒内部的内摩擦力有利于大肠杆菌的沉积,流动速度对大肠杆菌引起的微生物堵塞起到关键作用:2)3种(60、80、100 cm)不同长度的试验箱体在流速作用下以100和80 cm为对象,其沉积率提高了57.1%;以80和60 cm为对比对象,其沉积率提高了27.3%;3)大肠杆菌的恢复率与流体速度也成正相关作用,其堵塞原理类似沉积率特性。

大型地埋管群地源热泵三维传热-渗流耦合模拟

为确定地下水渗流对大尺度、多分支埋管集群地源热泵系统换热区温度场和换热特性的影响,基于上海天文馆880个地埋管地源热泵场地,建立考虑地下水渗流和地质分层的三维传热-渗流耦合模型,并利用现场热响应试验对模型进行验证。结果表明:渗流作用引起管群内和支管群之间沿地下水流动方向发生温度干扰,89.5~120.3 m埋深范围内的温度干扰现象相对明显;地下水渗流有利于提高管群的换热总量,缩小夏季和冬季工况的换热量差距;换热量增加百分比随水力梯度的增加而增大,两者呈对数函数关系,当水力梯度大于0.005时,换热量增加百分比趋于平稳。

水-冰相变凝固换热与热泵耦合供热系统实验研究

针对河北山区农村水源不足、地源钻井成本高、太阳能不稳定、造价高、没有合适的热泵低温热源等问题,研发了水-冰相变换热器;利用水的相变潜热作为热泵的低温热源,设计了水-冰相变凝固换热与热泵耦合供热系统,搭建了实验平台,经测试平台运行稳定可靠。通过对实验数据进行分析计算,得到系统性能系数在2.87~3.42之间。研究结果可为解决河北山区农村供暖问题提供参考。

“两抽两灌”水源热泵系统应用效果分析及优化布置

为探究丹东市某工程地下水源热泵系统的实际应用效果及布井方式的合理性,采用COMSOL Multiphysics软件,建立三维水热耦合数值模型,对“两抽两灌”水源热泵系统进行为时一年的运行水温监测,并对实际应用中抽灌井的布置方式以及抽灌井间距是否存在含水层“热贯通”问题进行分析,将存在的问题与工程场地条件相结合。结果表明,采用“抽灌井平行布置”时,且抽灌井间距离为55 m时,发生“热贯通”的程度最轻,为丹东市水源热泵规划提供科学设计方法及参考依据。

Performance analysis of air-water dual source heat pump water heater with heat recovery

A new air-water dual source heat pump water heater with heat recovery is proposed.The heat pump system can heat water by using a single air source,a single water source,or air-water dual sources.The water is first pre-heated by waste hot water,then heated by the heat pump.Waste heat is recovered by first preheating the cold water and as water source of the heat pump.According to the correlated formulas of the coefficient of performance of air-source heat pump and water-source heat pump,and the gain coefficient of heat recovery-preheater,the formulas for the coefficient of performance of heat pump in six operating modes are obtained by using the dimensionless correspondence analysis method.The system characteristics of heat absorption and release associated with the heat recovery-preheater are analyzed at different working conditions.The developed approaches can provide reference for the optimization of the operating modes and parameters.The results of analysis and experiments show that the coefficient of performance of the device can reach 4-5.5 in winter,twice as much as air source heat pump water heater.The utilization of waste heat in the proposed system is higher than that in the system which only uses waste water to preheating or as heat source.Thus,the effect of energy saving of the new system is obvious.On the other hand,the dimensionless correspondence analysis method is introduced to performance analysis of the heat pump,which also has theoretical significance and practical value.

油田联合站水源热泵能效比软测量方法及节能效果研究

油田联合站水源热泵的应用既有效减少了以天然气为燃料的加热炉碳排放量,又解决了采暖伴热和机泵冷却的问题。但如何能精准方便测量和提高其能效比(COP)值,对水源热泵在油田推广应用有着重大意义。为此,采用BP神经网络对油田在运水源热泵的COP进行建模,测得与实际运行参数平均相对误差均小于1%,证明这种基于BP神经网络建模的水源热泵COP值软测量方法是可行的;另外,通过仿真模型分析,提出将水源热泵间接式单蒸发工艺改进为直进式双蒸发工艺,水源热泵COP值由3.6~4.2提高到4.5~4.8,年节约电耗174.1×104 kWh。研究结果对油田水源热泵的推广应用和系统节能降耗起到了积极作用。

Data-driven sensitivity analysis and electricity consumption prediction for water source heat pump system using limited information

The studies on predicting the energy consumption of air conditioning systems are meaningful to building energy conservation and management. Generally, the more comprehensive the building information is, the easier the prediction model can be developed. However, it is very difficult to get detailed information about existing/old buildings (information-poor buildings), it is a big challenge to predict the energy consumption accurately by limited information. This study aims to predict the electricity consumption of the water source heat pump system of an office building based on meteorological data. The key variables are selected by error analysis and sensitivity analysis, and the effects of each variable on the models’ prediction performance can be obtained. Besides, the prediction models are established by support vector regression algorithm and trained by the local meteorological data. The results show that the positive and negative variables can be identified, and these positive variables are responsible for more than 70% of the total importance. Moreover, the root mean square error falls to 4.6044 from 7.8227 and the relative square error falls to 0.1494 from 0.4313 when the negative inputs are removed. And the errors reduce further to 4.1160 and 0.1194 by parameter optimization.

水环热泵系统辅助热源容量设计与调控策略

提出采用工况分析法设计水环热泵系统辅助热源容量,利用循环水能量变化量逆推建立辅助热源容量模型,并以天津地区某办公建筑群为实例,设计3种辅助热源容量方案,采用负荷与水温2种热量调控方案分析辅助热源对系统运行的影响,并采用负荷能耗分析法分析控制方案。测试结果表明:3种辅助热源容量方案均能够保证系统正常运行,按55%负荷率选取设计容量时,系统能效最高;优化中低负荷的供热量、实现机组与辅助热源能量平衡是提升系统能效的关键技术;相比负荷控制,水温调节更适宜水环热泵系统。

Water pumping analysis and experimental validation of beach well infiltration intake system in a seawater source heat pump system

Based on energy conservation equation and Darcy＇s law, a model of beach well infiltration intake system applied in a seawater source heat pump system was established. The model consists of the seawater seepage and the heat transfer process. A porous medium model in a software named FLUENT was applied to simulate the seepage and the heat transfer process. This model was also validated by field experiment conducted on the seashore in Tianjin, China. The maximum relative error between simulation results and experimental results was 2.1% （less than 5%）, which was acceptable in engineering applica- tion. The porosity and coefficient of thermal conductivity of the aquifer soil were determined to be 0.49 W/（m. K） and 1.46W/（m.K）, respectively in the simulation. In addition, the influencing factors of pumping water of beach well were also analyzed. The pumping water was found to increase when the distance between the beach well and the impervious boundary becomes longer, when the distance between the beach well and the supplying water source shortens, when the diameter of the beach well enlarges, and the drawdown enlarges.

竖进平出型地埋管群换热器结构与控制优化

【目的】为提高浅层地热能利用效率,亟须对影响地源热泵系统性能的地埋管换热器结构和控制开展优化设计。【方法】建立了一种竖进平出型地埋管群换热器模型,研究其换热系统性能,探究其最佳结构及运行方式。【结果】管群布置横纵比越低,单位面积换热量越大,横纵比超过0.15后对系统影响较小;换热器间距越小,土壤利用率越高,但热短路损失越大;双列双出型埋管每延米换热量相较于双列单出型结构提升7%以上;负荷较大工况下叉排布置结构的换热效果更好;整个夏季优化结构的平均出口温度下降2.28℃,换热器周围土壤温度下降1℃以上;实际运行过程中应优先考虑采用流速随负荷变化控制模式。【结论】研究结果可为地源热泵换热器的设计、制造提供理论依据。

土壤源热泵地埋管侧水系统优化运行研究

本文基于江苏无锡某典型厂房土壤源热泵空调项目的实测数据,以地源侧系统总能耗最低为目标,构建设备模型对地源水泵运行工况进行优化,并与两种传统控制策略的运行效果进行对比,据此提出进一步的优化建议。结果表明:基于负荷的优化控制策略,其节能效果要明显优于定频控制策略,冬夏季典型测试日平均节能率分别为28.33%和13.27%,相比于5℃温差变频策略节能了3.61%和2.21%。适当增大地埋管的埋管深度或管径,可以进一步提升该优化控制策略的节能效果。传统的定温差控制策略在负荷率大于60%时,可在5℃基础上将温差增加1~5℃以提升节能效果。

基于改进粒子群算法的中深层地源热泵供暖系统运行优化

构建变工况运行且包含蓄热装置的中深层地源热泵供暖系统,基于改进粒子群算法,分别以运行费用、系统COP和地热能利用系数为目标函数对系统运行进行优化,并对优化结果进行比较和分析。结果表明:对应目标函数优化后的运行费用、系统COP和地热能利用系数分别为279.27元、6.4420和0.8527。以系统COP为目标函数的优化效果与运行费用相反,而与地热能利用系数相近。

高校宿舍太阳能-空气源热泵复合热水系统设计与应用探讨

在当前积极倡导节能减排的政策要求下,可再生能源利用逐渐普及。以西安建筑科技大学学生宿舍太阳能-空气源热泵复合热水系统为例,阐述了复合热水系统的构成、工作原理,对太阳能集热系统、空气源热泵换热系统、热水供水系统等进行了设计计算,给出了集热器、热泵机组、集热水箱、供热水箱等主要设备的选型结果,提出了系统运行控制方案,并结合实际运行工况下的热性能数据,计算得到系统在不同季节的太阳能保证率、热泵能效比COP值,表明系统具有极大的节能性。

地埋管换热系统改造项目关键技术节点施工工艺研究

天津某管业公司建筑原采用常压燃气热水锅炉供热和分体式空调供冷,现拟以浅层地热能为基础能源对原供热制冷系统进行改造,施工前首先通过现场岩土热响应试验、地下管线探测等查明施工场地岩土体结构和换热能力,掌握地下综合管线的分布,并对建筑单位冷热负荷指标校正。重点阐述地埋管换热系统施工过程的关键技术节点,即竖直换热孔钻进、下管、回填及水平管线连接等,为类似改造项目提供参考。