Composition optimization and performance prediction for ultra-stable water-based aerosol based on thermodynamic entropy theory

Water-based aerosol is widely used as an effective strategy in electro-optical countermeasure on the battlefield used to the preponderance of high efficiency,low cost and eco-friendly.Unfortunately,the stability of the water-based aerosol is always unsatisfactory due to the rapid evaporation and sedimentation of the aerosol droplets.Great efforts have been devoted to improve the stability of water-based aerosol by using additives with different composition and proportion.However,the lack of the criterion and principle for screening the effective additives results in excessive experimental time consumption and cost.And the stabilization time of the aerosol is still only 30 min,which could not meet the requirements of the perdurable interference.Herein,to improve the stability of water-based aerosol and optimize the complex formulation efficiently,a theoretical calculation method based on thermodynamic entropy theory is proposed.All the factors that influence the shielding effect,including polyol,stabilizer,propellant,water and cosolvent,are considered within calculation.An ultra-stable water-based aerosol with long duration over 120 min is obtained with the optimal fogging agent composition,providing enough time for fighting the electro-optic weapon.Theoretical design guideline for choosing the additives with high phase transition temperature and low phase transition enthalpy is also proposed,which greatly improves the total entropy change and reduce the absolute entropy change of the aerosol cooling process,and gives rise to an enhanced stability of the water-based aerosol.The theoretical calculation methodology contributes to an abstemious time and space for sieving the water-based aerosol with desirable performance and stability,and provides the powerful guarantee to the homeland security.

Natural rubber latex as a potential additive for water-based drilling fluids

The environmental hazards and"carbon footprint"of oil and gas drilling can be significantly reduced by replacing traditional petroleum-based chemical additives with natural materials derived from plants and animals.This paper explored for the first time the interaction mechanism between natural rubber latex(NRL)and bentonite suspensions(BTs)through a series of characterization experiments,as well as the potential applications in water-based drilling fluids(WBDF).The gel viscoelasticity experiments showed that NRL could decrease the consistency coefficient(k)and flow index(n)of BTs,and enhance the shear thinning performance of BTs as pseudo-plastic fluids.In addition,0.5 w/v%NRL not only increased the critical yield stress and strengthened the structural strength between the bentonite particles,but also facilitated the compatibility of pressure loss and flow efficiency.The evaluation of colloidal stability and WBDF performance indicated that NRL particles could promote the hydration and charge stability on the surface of BTs particles,and optimize the particle size distribution and flow resistance of WBDF under the"intercalation-exfoliation-encapsulation"synergistic interaction.Moreover,NRL can improve the rheological properties of WBDF at high temperatures(<150.C),and form a dense blocking layer by bridging and sealing the pores and cracks of the filter cake,which ultimately reduces the permeability of the cake and the filtration loss of WBDF.

Indoor Formaldehyde Removal Techniques through Paints: Review

Due to its ability to cause illnesses and discomfort even at low concentrations, formaldehyde pollution of indoor air poses a significant risk to human health. Sources of formaldehyde in indoor environments include textiles, paints, wallpapers, glues, adhesives, varnishes, and lacquers;furniture and wooden products like particleboard, plywood, and medium-density fiberboard that contain formaldehyde-based resins;shoe products;cosmetics;electronic devices;and other consumer goods like paper products and insecticides. According to the World Health Organisation, indoor formaldehyde concentrations shouldn’t exceed 0.1 mg/m3. The methods include membrane separation, plasma, photocatalytic decomposition, physisorption, chemisorption, biological and botanical filtration, and catalytic oxidation. Materials based on metal oxides and supported noble metals work as oxidation catalysts. Consequently, a paint that passively eliminates aldehydes from buildings can be developed by adding absorbents and formaldehyde scavengers to the latex composition. It will be crucial to develop techniques for the careful detection and removal of formaldehyde in the future. Additionally, microbial decomposition is less expensive and produces fewer pollutants. The main goal of future research will be to develop a biological air quality control system that will boost the effectiveness of formaldehyde elimination. The various methods of removing formaldehyde through paints have been reviewed here, including the use of mixed metal oxides, formaldehyde-absorbing emulsions, nano titanium dioxide, catalytic oxidation, and aromatic formaldehyde abating materials that can improve indoor air quality.

Improving the anti-collapse performance of water-based drilling fluids of Xinjiang Oilfield using hydrophobically modified silica nanoparticles with cationic surfactants

Wellbore instability,especially drilling with water-based drilling fluids(WBDFs)in complex shale for-mations,is a critical challenge for oil and gas development.The purpose of this paper is to study the feasibility of using hydrophobically modified silica nanoparticle(HMN)to enhance the comprehensive performance of WBDFs in the Xinjiang Oilfield,especially the anti-collapse performance.The effect of HMN on the overall performance of WBDFs in the Xinjiang Oilfield,including inhibition,plugging,lu-bricity,rheology,and filtration loss,was studied with a series of experiments.The mechanism of HMN action was studied by analyzing the changes of shale surface structure and chemical groups,wettability,and capillary force.The experimental results showed that HMN could improve the performance of WBDFs in the Xinjiang Oilfeld to inhibit the hydration swelling and dispersion of shale.The plugging and lubrication performance of the WBDFs in the Xinjiang Oilfield were also enhanced with HMN based on the experimental results.HMN had less impact on the rheological and filtration performance of the WBDFs in the Xinjiang Oilfield.In addition,HMN significantly prevented the decrease of shale strength.The potential mechanism of HMN was as follows.The chemical composition and structure of the shale surface were altered due to the adsorption of HMN driven by electrostatic attraction.Changes of the shale surface resulted in significant wettability transition.The capillary force of the shale was converted from a driving force of water into the interior to a resistance.In summary,hydrophobic nanoparticles presented afavorable application potential for WBDFs.

Hydrophobic Small-Molecule Polymers as High-Temperature-Resistant Inhibitors in Water-Based Drilling Fluids

Water-based drilling fluids can cause hydration of the wellbore rocks,thereby leading to instability.This study aimed to synthesize a hydrophobic small-molecule polymer(HLMP)as an inhibitor to suppress mud shale hydration.An infrared spectral method and a thermogravimetric technique were used to characterize the chemical composition of the HLMP and evaluate its heat stability.Experiments were conducted to measure the linear swelling,rolling recovery rate,and bentonite inhibition rate and evaluate accordingly the inhibition performance of the HLMP.Moreover,the HLMP was characterized through measurements of the zeta potential,particle size distribution,contact angles,and interlayer space testing.As confirmed by the results,the HLMP could successfully be synthesized with a favorable heat stability.Furthermore,favorable results were found for the inhibitory processes of the HLMP on swelling and dispersed hydration during mud shale hydration.The positively charged HLMP could be electrically neutralized with clay particles,thereby inhibiting diffusion in the double electron clay layers.The hydrophobic group in the HLMP molecular structure resulted in the formation of a hydrophobic membrane on the rock surface,enhancing the hydrophobicity of the rock.In addition,the small molecules of the HLMP could plug the spaces between the layers of bentonite crystals,thereby reducing the entry of water molecules and inhibiting shale hydration.

Water-based synthesis of nanoscale hierarchical metal-organic frameworks:Boosting adsorption and catalytic performance

The combination of nano sizes,large pore sizes and green synthesis is recognized as one of the most crucial and challenging problems in constructing metal-organic frameworks(MOFs).Herein,a water-based strategy is proposed for the synthesis of nanoscale hierarchical MOFs(NH-MOFs)with high crystallinity and excellent stability.This approach allows the morphology and porosity of MOFs to be fine tuned,thereby enabling the nanoscale crystal generation and a well-defined hierarchical system.The aqueous solution facilitates rapid nucleation kinetics,and the introduced modulator acts as a deprotonation agent to accelerate the deprotonation of the organic ligand as well as a structure-directing agent(SDA)to guide the formation of hierarchical networks.The assynthesized NH-MOFs(NH-ZIF-67)were assessed as efficient adsorbents and heterogeneous catalysts to facilitate the diffusion of guest molecules,outperforming the parent microZIF-67.This study focuses on understanding the NH-MOF growth rules,which could allow tailor-designing NH-MOFs for various functions.

Water-Based Environmentally Friendly Pesticide Formulations Based on Cyclodextrin/Pesticide Loading System

Difenoconazole(DIF)is a representative variety of broad-spectrum triazole fungicides and liposoluble pesticides.However,the water solubility of DIF is so poor that its application is limited in plant protection.In addition,the conventional formulations of DIF always contain abundant organic solvents,which may cause pollution of the environment.In this study,two DIF/cyclodextrins(CDs)inclusion complexes(ICs)were successfully prepared,which were DIF/β-CD IC and DIF/hydroxypropyl-β-CD IC(DIF/HP-β-CD IC).The effect of cyclodextrins on the water solubility and the antifungal effect of liposoluble DIF pesticide were investigated.According to the phase solubility test,the molar ratio and apparent stability constant of ICs were obtained.Fourier transform infrared spectroscopy,thermal gravity analysis,X-ray diffraction and scanning electron microscopy were used systematically to characterize the formation and characteristics of ICs.The results noted that DIF successfully entered the cavities of two CDs.In addition,the antifungal effect test proved the better performance of DIF/HP-β-CD IC,which exceeded that of DIF emulsifiable concentrate.Therefore,our study provides informative direction for the intelligent use of liposoluble pesticides with cyclodextrins to develop water-based environmentally friendly formulations.

De Novo Synthesis of Biopaint Using Transformed Bacteria: Analysis of Spectral Intensity Trends and Comparison to Commercial Paint

Background: Commercial paint pigments contain toxic heavy metals that harm humans and pollute the environment. To mitigate these harms, ecologically safe pigments are necessary. Objective: This experiment aims to create a biopaint de-novo using transformed Escherichia coli bacteria and compare it to commercial paint. Methods: Genetically engineered E. coli bacteria producing magenta pigment were grown in petri dishes. The pigment protein was extracted, filtered, and dehydrated into a crystalline powder. This was mixed with acrylic medium to make biopaint. The biopaint and commercial paint were applied on acrylic paper;red, green, blue, and total spectral intensities were measured daily under different testing conditions. Spectral intensity variability was measured and compared using the Coefficient of Variation (CV). Trends in spectral intensity were analyzed using regression analysis. Results: The differences in the CV of biopaint to commercial paint were less than 20% under all testing conditions. Spectral intensities for both biopaint and commercial paint did not show any significant change during the testing period under the conditions of room temperature, heat, and humidity. However, under the cold testing condition, biopaint showed a slight but statistically significant (p-value Conclusion: This experiment proves that E. coli-derived pigments can be used to make biopaint which has a similar durability to commercial paint as measured by the spectral intensities.

Investigation of the Film Formation in Dynamic Air Spray Painting

To accurately predict the film thickness distribution during dynamic spraying performed with air guns and support accordingly the development of intelligent spray painting,the spray problem was analyzed numerically.In particular,the Eulerian-Eulerian approach was employed to calculate the paint atomization and film deposition process.Different spray heights,spray angles,spray gun movement speeds,spray trajectory curvature radii,and air pressure values were considered.Numerical simulation results indicate that the angle of spray painting significantly affects the velocity of droplets near the spray surface.With an increase in the spraying angle,spraying height and spray gun movement speed,the maximum film thickness decreases to varying degrees,and the uniformity of the film thickness also continuously worsens.When the spray gun moves along an arc trajectory,at smaller arc radii,the film thickness on the inside of the arc is slightly greater than that on the outside,but the impact on the maximum film thickness is minimal.Increasing air pressure expands the coating coverage area,results in finer atomization of paint droplets,and leads to a thinner and a more uniform paint film.However,if the pressure is too high,it can cause paint splattering.Using the orthogonal experimental method,multiple sets of simulation calculations were conducted,and the combined effects of spraying height,spray angle,and spray gun movement speed on the film thickness distribution were comprehensively analyzed to determine optimal configurations.Finally,the reliability of the numerical simulations was validated through dynamic spray painting experiments.

Drishti Paint 3.2:a new open-source tool for both 2D and 3D segmentation

X-ray computed tomography(CT)has been an important technology in paleontology for several decades.It helps researchers to acquire detailed anatomical structures of fossils non-destructively.Despite its widespread application,developing an efficient and user-friendly method for segmenting CT data continues to be a formidable challenge in the field.Most CT data segmentation software operates on 2D interfaces,which limits flexibility for real-time adjustments in 3D segmentation.Here,we introduce Curves Mode in Drishti Paint 3.2,an open-source tool for CT data segmentation.Drishti Paint 3.2 allows users to manually or semi-automatically segment the CT data in both 2D and 3D environments,providing a novel solution for revisualizing CT data in paleontological studies.

Co-pyrolysis of Sewage Sludge with Paint Sludge: Kinetics and Thermodynamic Analysis via Iso-conversional Methods

This study explored the synergistic interaction of sewage sludge(SS)and automotive paint sludge(PS)during co-pyrolysis for the optimized treatment of sewage sludge in cement kiln systems,utilizing thermogravimetric analysis(TGA)and thermogravimetric-mass spectrometry(TGA-MS).The result reveals the coexisting synergistic and antagonistic effects in the co-pyrolysis of SS/PS.The synergistic effect arises from hydrogen free radicals in SS and catalytic components in PS,while the main source of the antagonistic effect is that,during the mechanical mixing process,the SS/PS is converted from the particulate form into a dough-like rubbery which contributes to the film-forming effect,hindering the volatilization of volatile components.SS/PS co-pyrolysis reduces the yielding of tar production while increasing coke and gas.This study will provide some in-depth insights into the co-pyrolysis of SS/PS,and offer theoretical support for the subsequent research on the collaborative disposal processes in cement kilns.

Improved Scatter Search Algorithm for Multi-skilled Personnel Scheduling of Ship Block Painting

This paper focuses on the optimization method for multi-skilled painting personnel scheduling.The budget working time analysis is carried out considering the influence of operating area,difficulty of spraying area,multi-skilled workers,and worker’s efficiency,then a mathematical model is established to minimize the completion time. The constraints of task priority,paint preparation,pump management,and neighbor avoidance in the ship block painting production are considered. Based on this model,an improved scatter search(ISS)algorithm is designed,and the hybrid approximate dynamic programming(ADP)algorithm is used to improve search efficiency. In addition,the two solution combination methods of path-relinking and task sequence combination are used to enhance the search breadth and depth. The numerical experimental results show that ISS has a significant advantage in solving efficiency compared with the solver in small scale instances;Compared with the scatter search algorithm and genetic algorithm,ISS can stably improve the solution quality. Verified by the production example,ISS effectively shortens the total completion time of the production,which is suitable for scheduling problems in the actual painting production of the shipyard.

The Study of “Imitation” Aesthetics in Ancient Painting Theory-Taking the Chinese and Western Sources as an Example

The theory of“imitation”in painting occupies a leading position in western art,which originated from the theory of“imitation”in ancient Greece,and has become one of the art theories affecting the world through the continuous development of later generations.Through the exploration of the source of“imitation”in China and the West,there are some comments on the meaning of“imitation”in Chinese classical painting theory,such as“transfer model writing”and“image form”,which is obvious differences from the west.Traditional Chinese painting is a combination of careful observation of natural things and subjective emotions to express their own aesthetic feelings,and ultimately form a vivid artistic conception.Modern imitation is borrowed from Western imitation.In fact,imitation in traditional painting has its own meaning,which contains Chinese aesthetic thought.“Imitation”aesthetics is unique in traditional Chinese painting and is the most important form of painting art.

Analysis of Color and Artistic Conception in Painting Art

The charm of painting,as a bright pearl in the treasure house of culture,lies in its visual language constructed through colors and lines,which conveys the artist’s unique perception of life and profound emotions.Color,as the most intuitive and expressive language in painting,is not only a simple reproduction of material colors but also a projection of the artist’s inner world.Artistic conception,as a core concept in traditional Chinese painting theory,refers to the emotional atmosphere and spiritual mood embedded in paintings.The purpose of this paper is to discuss the interaction between color and mood in painting art,to analyze the techniques of using color in different painting styles and their influence on the creation of mood,and to provide new perspectives and methods for the creation of paintings.

Exploration of the Expression of Color Emotion in Oil Painting Sketch Creation

This paper deeply analyzes the expression of color emotion in oil painting sketch creation.Starting with the three basic attributes of color theory(hue,lightness,and purity),this paper discusses its emotional symbolic significance and the relationship between contrast and harmony.By interpreting the works of artists such as Van Gogh’s Sunflower,Monet’s Rouen Cathedral,and Cézanne’s Mont Sainte-Victoire,this paper shows the unique charm of different colors in conveying emotions,creating atmosphere,and expressing themes.At the same time,it is expounded that in the creation of an oil painting sketch,the effective expression of color emotion can be realized by observing nature,using subjective colors,and reasonable composition and layout of colors,so as to enhance the artistic value of the works.

Analysis of Viewing Paintings from the Perspective of Iconography

Distinguished from purely formalistic research methods,iconography pursues the interpretation of the hidden historical and humanistic connotations behind artworks,and is a discipline that combines visual text and content analysis methods.Combining the three stages of iconography proposed by Panofsky,the paper studies Shizeng Chen’s Viewing Paintings from the perspective of iconography,summarizing the formation and change of the images and contents of the artworks in the cultural system and civilization at that time,as well as their implied ideology,and analyzing the hidden spirit of the times and the historical significance behind them,so as to expound their iconographic significance.Through an in-depth discussion at three levels:pre-pictorial iconographic description,iconographic analysis,and iconographic interpretation,the facts and surface contents reproduced in the images,the traditional level of literary,artistic,and cultural knowledge,as well as the interpretation of the potential meanings are revealed.

Color Expression and Mood Creation in Imagery Oil Painting

Oil painting is a traditional Western painting form.With the introduction of China and the influence of China’s traditional painting and aesthetics,the painting style became more distinctive,expanding a new development direction of oil painting,and thus imagery oil painting came into being.Color,as the most important element in imagery oil painting,mainly plays the role of mood creation and emotional expression.Many creators are good at injecting their thoughts and emotions into the paintings through color matching,so as to enhance the artistic expression of the paintings.This paper analyzes the color expression characteristics of imagery oil painting and explores the color expression techniques in imagery oil painting and mood creation of imagery oil painting from several aspects.

Carbon nanotube enhanced water-based drilling fluid for high temperature and high salinity deep resource development

Drilling fluids face failure during drilling deep reservoir with high temperature and high salt.The experimental results show that high temperature and salinity reduce the negative charge on the surface of bentonite in the drilling fluid and cause the coalescence of bentonite particles.As a result,the particles coalesce,the grid structure is destroyed,and the rheological properties,rock-carrying capacity and filtration properties are lost.To resolve the foregoing,in this study,0.05-wt%carbon nanotubes are introduced into a 4%bentonite drilling fluid under conditions where the temperature and concentration of added Na Cl reach 180°C and 10 wt%,respectively.The carbon nanotubes adsorb on the bentonite surface and increase the space among bentonite particles.The steric hindrance prevents the coalescence of bentonite in high temperature and high salt environment.Thus bentonite maintains the small size distribution of bentonite and supports the bentonite grid structure in the drilling fluid.As a result,the rock-carrying capacity of the drilling fluid increases by 85.1%.Moreover,the mud cake formed by the accumulation of small-sized bentonite particles is dense;consequently,the filtration of bentonite drilling fluid reduced by 30.2%.

High temperature and high pressure rheological properties of high-density water-based drilling fluids for deep wells

To maintain tight control over rheological properties of high-density water-based drilling fluids, it is essential to understand the factors influencing the theology of water-based drilling fluids. This paper examines temperature effects on the rheological properties of two types of high-density water-based drilling fluids （fresh water-based and brine-based） under high temperature and high pressure （HTHP） with a Fann 50SL rheometer. On the basis of the water-based drilling fluid systems formulated in laboratory, this paper mainly describes the influences of different types and concentration of clay, the content of a colloid stabilizer named GHJ-1 and fluid density on the rheological parameters such as viscosity and shear stress. In addition, the effects of aging temperature and aging time of the drilling fluid on these parameters were also examined. Clay content and proportions for different densities of brine-based fluids were recommended to effectively regulate the rheological properties. Four theological models, the Bingham, power law, Casson and H-B models, were employed to fit the rheological parameters. It turns out that the H-B model was the best one to describe the rheological properties of the high-density drilling fluid under HTHP conditions and power law model produced the worst fit. In addition, a new mathematical model that describes the apparent viscosity as a function of temperature and pressure was established and has been applied on site.

Measurements of Formaldehyde and TVOC Emission from Paints and Coating Materials using Small Chamber Method for Building Composites

An optimal test method for paint is proposed; additionally, the Field and Laboratory Emission Cell （FLEC） method used in Europe is applied as a substitute for the 20 L small chamber method. The emission factors of total volatile organic compounds （TVOC） and formaldehyde from oil-based paint, emulsion paint, and water-dispersion paint with a coating weight of 300 g/m2, cured for 24/48 hours, were measured using the 20 L small chamber method. The emission rate of TVOC and formaldehyde from all paints began to stabilize after approximately 7 days after 24/48 hours of curing even though Korean standards stipulate that paint should be measured and analyzed after the third day of application. The emission factor of TVOC and formaldehyde from oil-based, emulsion, and water-dispersion paints were also measured using the FLEC method. There was good correlation between the 20 L small chamber method and the FLEC method for oil-based, emulsion, and water-dispersion paint emissions. With the FLEC method, using paints prepared under identical conditions, the emission rate was stable 24 hours after installation of samples because the air flow rate of FLEC is much higher than that of a 20 L small chamber, and the relative cell volume of FLEC is much smaller than that of a 20 L small chamber.