The water-saving potential of using micro-sprinkling irrigation for winter wheat production on the North China Plain

The shortage of groundwater resources is a considerable challenge for winter wheat production on the North China Plain.Water-saving technologies and procedures are thus urgently required.To determine the water-saving potential of using micro-sprinkling irrigation(MSI)for winter wheat production,field experiments were conducted from 2012 to 2015.Compared to traditional flooding irrigation(TFI),micro-sprinkling thrice with 90 mm water(MSI1)and micro-sprinkling four times with 120 mm water(MSI2)increased the water use efficiency by 22.5 and 16.2%,respectively,while reducing evapotranspiration by 17.6 and 10.8%.Regardless of the rainfall pattern,MSI(i.e.,MSI1 or MSI2)either stabilized or significantly increased the grain yield,while reducing irrigation water volumes by 20–40%,compared to TFI.Applying the same volumes of irrigation water,MSI(i.e.,MSI3,micro-sprinkling five times with 150 mm water)increased the grain yield and water use efficiency of winter wheat by 4.6 and 11.7%,respectively,compared to TFI.Because MSI could supply irrigation water more frequently in smaller amounts each time,it reduced soil layer compaction,and may have also resulted in a soil water deficit that promoted the spread of roots into the deep soil layer,which is beneficial to photosynthetic production in the critical period.In conclusion,MSI1 or MSI2 either stabilized or significantly increased grain yield while reducing irrigation water volumes by 20–40%compared to TFI,and should provide water-saving technological support in winter wheat production for smallholders on the North China Plain.

Using irrigation intervals to optimize water-use efficiency and maize yield in Xinjiang,northwest China

Worldwide, scarce water resources and substantial food demands require efficient water use and high yield.This study investigated whether irrigation frequency can be used to adjust soil moisture to increase grain yield and water use efficiency(WUE) of high-yield maize under conditions of mulching and drip irrigation.A field experiment was conducted using three irrigation intervals in 2016: 6, 9, and 12 days(labeled D6, D9, and D12) and five irrigation intervals in 2017: 3, 6, 9, 12, and 15 days(D3, D6, D9, D12, and D15).In Xinjiang, an optimal irrigation quota is 540 mm for high-yield maize.The D3, D6, D9, D12, and D15 irrigation intervals gave grain yields of 19.7, 19.1–21.0, 18.8–20.0, 18.2–19.2, and 17.2 Mg ha^-1 and a WUE of 2.48, 2.53–2.80, 2.47–2.63, 2.34–2.45, and 2.08 kg m-3, respectively.Treatment D6 led to the highest soil water storage, but evapotranspiration and soil-water evaporation were lower than other treatments.These results show that irrigation interval D6 can help maintain a favorable soil-moisture environment in the upper-60-cm soil layer, reduce soilwater evaporation and evapotranspiration, and produce the highest yield and WUE.In this arid region and in other regions with similar soil and climate conditions, a similar irrigation interval would thus be beneficial for adjusting soil moisture to increase maize yield and WUE under conditions of mulching and drip irrigation.

Effects of water application uniformity using a center pivot on winter wheat yield, water and nitrogen use efficiency in the North China Plain

In recent years, the use of fertigation technology with center pivot irrigation systems has increased rapidly in the North China Plain (NCP). The combined effects of water and nitrogen application uniformity on the grain yield, water use efficiency (WUE) and nitrogen use efficiency (NUE) have become a research hotspot. In this study, a two-year field experiment was conducted during the winter wheat growing season in 2016–2018 to evaluate the water application uniformity of a center pivot with two low pressure sprinklers (the R3000 sprinklers were installed in the first span, the corresponding treatment was RS;the D3000 sprinklers were installed in the second span, the corresponding treatment was DS) and a P85A impact sprinkler as the end gun (the corresponding treatment was EG), and to analyze its effects on grain yield, WUE and NUE. The results showed that the water application uniformity coefficients of R3000, D3000 and P85A along the radial direction of the pivot (CUH) were 87.5, 79.5 and 65%, respectively. While the uniformity coefficients along the traveling direction of the pivot (CUC) were all higher than 85%. The effects of water application uniformity of the R3000 and D3000 sprinklers on grain yield were not significant (P>0.05);however, the average grain yield of EG was significantly lower (P<0.05) than those of RS and DS, by 9.4 and 11.1% during two growing seasons, respectively. The coefficients of variation (CV) of the grain yield had a negative correlation with the uniformity coefficient. The CV of WUE was more strongly affected by the water application uniformity, compared with the WUE value, among the three treatments. The NUE of RS was higher than those of DS and EG by about 6.1 and 4.8%, respectively, but there were no significant differences in NUE among the three treatments during the two growing seasons. Although the CUH of the D3000 sprinklers was lower than that of the R3000, it had only limited effects on the grain yield, WUE and NUE. However, the cost of D3000 sprinklers is lower than that of R3000 sprinklers. Therefore, the D3000 sprinklers are recommended for winter wheat irrigation and fertigation in the NCP.

Improving Water Use Efficiency for a Sustainable Productivity of Agricultural Systems Using Subsurface Drip Irrigation

The sustainability of agricultural production depends on conservation and appropriate use and management of scarce water resources especially in arid and semi-arid areas where irrigation is required for the production of food and cash crops. The objective of this paper was to evaluate the effects of surface and subsurface drip irrigation （SDI） at 5, 20 and 35 cm depths on water＇s dynamic in soil （Soil moisture distribution, water＇s stock in soil and irrigation water use efficiency） to produce maize in semiarid climates. Field study was conducted at the Higher Institute of Agronomy of Chott Meriem, Tunisia. The results indicated that soil moisture content under subsurface drip irrigation at 35 cm （T3） depth was more uniform compared to 5 cm （T1） and 20 cm （T2）. Moreover, irrigation water use efficiency was higher in this treatment. Indeed, it increased about 18%, 14% and 7% for T3, T2 and T1, respectively when compared with surface drip irrigation. The results of the present study showed that SDI allows uniform soil moisture, minimize the evaporative loss and delivery water directly to the plant root zone and consequently increases use efficiency. Further research is needed in order to determine whether corn production with SDI is feasible in the arid region.

High-Precision Direct Determination of the ^(87)Sr/^(86)Sr Isotope Ratio of Bottled Sr-Rich Natural Mineral Drinking Water Using MC-ICP-MS

Strontium has four naturally occurring stable isotopes,84Sr,86Sr,87Sr,and 88Sr,with abundances of 0.56,9.87,approximately 7.04,and 82.53 atomic %,respectively.The 87Sr/86Sr isotope ratio is variable due to the addition of radiogenic 87Sr produced by the beta decay of 87Rb with a half-life of 4.88 ± 0.05 Ga.Thus,

Assessing Water Availability and Unmet Water Demand Using the WEAP Model in the Semi-Arid Bweengwa, Kasaka and Magoye Sub-Catchments of Southern Zambia

Located in the semi-arid zone of Zambia, the Mutama-Bweengwa, Kasaka and Magoye sub-catchments have witnessed a high demand for water due to increase in population and socio-economic activities putting more pressure on water resources. This study assesses the hydrological components and ascertains the available water resources and unmet demand in the sub-catchments using the Water Evaluation And Planning (WEAP) Model and hydrometeorological data collected between 1951 and 2018. The model was calibrated and validated on 1971-1981 and 2008-2018 data respectively. The results reveal that the sub-catchments have transitioned from positive to negative water balance with -164.295 Mm3/year for Mutama-Bweengwa, -19.021 Mm3/year for Kasaka and -86.368 Mm3/year for Magoye. Evaporation was 1815.259 Mm3/year for Mutama-Bweengwa, 1162.655 Mm3/year for Kasaka and 1505.664 Mm3/year for Magoye. The demand for water has been increasing over time for various purposes such as irrigation, domestic, urban/rural water supply and livestock. The overall water storage in the sub-catchments showed a negative water balance for the year 2018. The observed and simulated peak streamflow were 8.16 m3/s and 7.7 m3/s occurring during the month of January and February respectively. The WEAP model performance achieved R2 of 0.98 during calibration and 0.95 for validation, and an NSE of 0.83 for calibration and 0.85 during validation. The values of objective functions show that the hydrology of the Mutama-Bweengwa, Kasaka and Magoye sub-catchments as predicted by the WEAP model provides satisfactory confidence for prediction of future streamflow and hence projection based on future scenarios.

Determination of Leafy Vegetables Need in Water andNitrogen Use Efficiency by Using the Diviner 2000 andthe Isotopes Techniques: Case of Amaranth(Amaranthus cruentus)

A study was conducted to determine how the nitrogen(N)in the fertilisers can be quantified and what amounts of fertilizers should be given to leafy vegetables to achieve their requirements.This study also aimed to determine the efficient use of water by the plant.The experiment was laid out in a randomized complete block with three replicates and three levels of urea(T0=0 kg/ha,T1=43.5 kg/ha,T2=65 kg/ha).Estimation of growth parameters and biomass yield revealed that the treatments produced statistically identical values.But numerically,T1(43.5 kg of urea/ha)gave the highest yields and T2(65 kg of urea/ha)produced the lowest.It was the same for the determination of the water use efficiency(WUE)by the plant where T1 produced the highest values compared to T2.The yield curve as a function of the applied urea dose allowed the identification of the urea dose that corresponds to optimal yield in amaranth.From the dose of 65 kg of urea/ha,any increase becomes harmful to the plant.This results in a decrease in yield in the amaranth plant.

Determination of Chromate Ion in Water Using High Performance Capillary Electrophoresis

A new rapid method for the analysis of chromate ion in water by using high performance capillary electrophoresis is described. The detection limit is 1.0 mu g/ml by using 100 m mol/l Tris-HCl buffer containing 2 m mol/l 1,6-hexanediamine which was used as an electroosmosis modifier to improve the separation and detection sensitivity.

Quality Problems in Waters Used for Drinking Purposes in Italy

With a grant from the Italian Ministry of the Environment, the National Institute of Health (Istituto Superiore di Sanita) promoted and coordinated some activities aimed at determining the extent and the intensity of contamination of waters used for human consumption by some chemical agents, and describing causes and modalities of contamination and human health implications. The chemical agents examined were herbicides, nitrates, trihalomethanes, asbestos, manganese and fluoride. In this paper a first nationwide picture of these problems is reported.

Rainwater Harvesting in Multifamily Social Interest Housing

This study evaluated the reduction of water consumption in a SIH （social interest housing） complex from the simulation of implanting a rainwater harvesting system. The methodology consisted of characterization of the case study, survey data of water consumption and data of precipitation in the area, on-site visits to define the average consumption and monthly water distribution, and sizing of a rainwater harvesting tank following the Netuno Program. It was obtained 22.500 L as the ideal volume for the tank, supplying the demand for drinkingwater in 32%, although the reduction in the drinking water bills would be minor, since the object of the case study is considered SIH, and residents pay a fixed fee for consuming up to 10 m3 per month. Therefore, it becomes necessary to analyze this situation from a sustainable and environmental perspective, and the benefits are no longer only economic, but rather they take on a more comprehensive social dimension.

Sequential Parameter Estimation Using Modal Dispersion Curves in Shallow Water

Existing sequential parameter estimation methods use the acoustic pressure of a line array as observations. The modal dispersion curves are employed to estimate the sound speed profile（SSP） and geoacoustic parameters based on the ensemble Kalman filter. The warping transform is implemented to the signals received by a single hydrophone to obtain the dispersion curves. The experimental data are collected at a range-independent shallow water site in the South China Sea. The results indicate that the SSPs are well estimated and the geoacoustic parameters are also well determined. Comparisons of the observed and estimated modal dispersion curves show good agreement.

A study on the simulation of carbon and water fluxes of Dangxiong alpine meadow and its response to climate change

The alpine meadow ecosystem accounts for 27%of the total area of the Tibetan Plateau and is also one of the most important vegetation types.The Dangxiong alpine meadow ecosystem,located in the south-central part of the Tibetan Plateau,is a typical example.To understand the carbon and water fluxes,water use efficiency(WUE),and their responses to future climate change for the alpine meadow ecosystem in the Dangxiong area,two parameter estimation methods,the Model-independent Parameter Estimation(PEST)and the Dynamic Dimensions Search(DDS),were used to optimize the Biome-BGC model.Then,the gross primary productivity(GPP)and evapotranspiration(ET)were simulated.The results show that the DDS parameter calibration method has a better performance.The annual GPP and ET show an increasing trend,while the WUE shows a decreasing trend.Meanwhile,ET and GPP reach their peaks in July and August,respectively,and WUE shows a“dual-peak”pattern,reaching peaks in May and November.Furthermore,according to the simulation results for the next nearly 100 years,the ensemble average GPP and ET exhibit a significant increasing trend,and the growth rate under the SSP5–8.5 scenario is greater than that under the SSP2–4.5 scenario.WUE shows an increasing trend under the SSP2–4.5 scenario and a significant increasing trend under the SSP5–8.5 scenario.This study has important scientific significance for carbon and water cycle prediction and vegetation ecological protection on the Tibetan Plateau.

Yields,growth and water use under chemical topping in relations to row configuration and plant density in drip-irrigated cotton

Background Water deficit is an important problem in agricultural production in arid regions.With the advent of wholly mechanized technology for cotton planting in Xinjiang,it is important to determine which planting mode could achieve high yield,fiber quality and water use efficiency(WUE).This study aimed to explore if chemical topping affected cotton yield,quality and water use in relation to row configuration and plant densities.Results Experiments were carried out in Xinjiang China,in 2020 and 2021 with two topping method,manual topping and chemical topping,two plant densities,low and high,and two row configurations,i.e.,76 cm equal rows and 10+66 cm narrow-wide rows,which were commonly applied in matching harvest machine.Chemical topping increased seed cotton yield,but did not affect cotton fiber quality comparing to traditional manual topping.Under equal row spacing,the WUE in higher density was 62.4%higher than in the lower one.However,under narrow-wide row spacing,the WUE in lower density was 53.3%higher than in higher one(farmers’practice).For machine-harvest cotton in Xinjiang,the optimal row configuration and plant density for chemical topping was narrow-wide rows with 15 plants m-2 or equal rows with 18 plants m-2.Conclusion The plant density recommended in narrow-wide rows was less than farmers’practice and the density in equal rows was moderate with local practice.Our results provide new knowledge on optimizing agronomic managements of machine-harvested cotton for both high yield and water efficient.

Effects of thinning and understory removal on water use efficiency of Pinus massoniana:evidence from photosynthetic capacity and stable carbon isotope analyses

Understanding the relationship between forest management and water use efficiency(WUE)is important for evaluating forest adaptability to climate change.However,the effects of thinning and understory removal on WUE and its key controlling processes are not well understood,which limits our comprehension of the physiological mechanisms of various management practices.In this study,four forest management measures(no thinning:NT;understory removal:UR;light thinning:LT;and heavy thinning:HT)were carried out in Pinus massoniana plantations in a subtropical region of China.Photosynthetic capacity and needle stable carbon isotope composition(δ^(13)C)were measured to assess instantaneous water use efficiency(WUE_(inst))and long-term water use efficiency(WUE_(i)).Multiple regression models and structural equation modelling(SEM)identified the effects of soil properties and physiological performances on WUE_(inst)and WUE_(i).The results show that WUE_(inst)values among the four treatments were insignificant.However,compared with the NT stand(35.8μmol·mol^(-1)),WUE_(i)values significantly increased to 41.7μmol·mol^(-1)in the UR,50.1μmol·mol^(-1)in the LT and 46.6μmol·mol^(-1)in HT treatments,largely explained by photosynthetic capacity and soil water content.Understory removal did not change physiological performance(needle water potential and photosynthetic capacity).Thinning increased the net photosynthetic rate(A_n)but not stomatal conductance(g_s)or predawn needle water potential(ψ_(pd)),implying that the improvement in water use efficiency for thinned stands was largely driven by radiation interception than by soil water availability.In general,thinning may be an appropriate management measure to promote P.massoniana WUE to cope with seasonal droughts under future extreme climates.

Water and nitrogen footprint assessment of integrated agronomic practice management in a summer maize cropping system

The footprints of water and nitrogen(WF and NF)provide a comprehensive overview of the type and quantity of water consumption and reactive nitrogen(Nr)loss in crop production.In this study,a field experiment over two years(2019 and 2020)compared three integrated agronomic practice management(IAPM)systems:An improved management system(T2),a high-yield production system(T3),and an integrated soil-crop management system(ISCM)using a local smallholder farmer’s practice system(T1)as control,to investigate the responses of WF,Nr losses,water use efficiency(WUE),and nitrogen use efficiency(NUE)to IAPM.The results showed that IAPM optimized water distribution and promoted water use by summer maize.The evapotranspiration over the whole maize growth period of IAPM increased,but yield increased more,leading to a significant increase in WUE.The WUE of the T2,T3,and ISCM treatments was significantly greater than in the T1 treatment,in 2019 and 2020respectively,by 19.8-21.5,31.8-40.6,and 34.4-44.6%.The lowest WF was found in the ISCM treatment,which was 31.0%lower than that of the T1 treatment.In addition,the ISCM treatment optimized soil total nitrogen(TN)distribution and significantly increased TN in the cultivated layer.Excessive nitrogen fertilizer was applied in treatment T3,producing the highest maize yield,and resulting in the highest Nr losses.In contrast,the ISCM treatment used a reduced nitrogen fertilizer rate,sacrificing grain yield partly,which reduced Nr losses and eventually led to a significant increase in nitrogen use efficiency and nitrogen recovery.The Nr level in the ISCM treatment was34.8%lower than in the T1 treatment while NUE was significantly higher than in the T1 treatment by 56.8-63.1%in2019 and 2020,respectively.Considering yield,WUE,NUE,WF,and NF together,ISCM should be used as a more sustainable and clean system for sustainable production of summer maize.

Rice Cultivation under Film Mulching Can Improve Soil Environment and Be Beneficial for Rice Production in China

Rice cultivation under film mulching is an integrated management technology that can conserve water, increase soil temperature, improve yield, and enhance water and nitrogen use efficiencies. Despite these advantages, the system does have its drawbacks, such as soil organic matter reduction and microplastic pollution, which impede the widespread adoption of film mulching cultivation in China. Nonetheless, the advent of degradable film, controlled-release fertilizer, organic fertilizer, and film mulching machinery is promoting the development of rice film mulching cultivation. This review outlines the impact of rice cultivation under film mulching on soil moisture, soil temperature, soil fertility, greenhouse gas emissions, weed control, and disease and pest management. It also elucidates the mechanism of changes in rice growth, yield and quality, water use efficiency, and nitrogen use efficiency. This paper incorporates a review of published research articles and discusses some uncertainties and shortcomings associated with rice cultivation under film mulching. Consequently, prospective research directions for the technology of rice film mulching cultivation are outlined, and recommendations for future research into rice cultivation under film mulching are proposed.

Effects of Water-Fertilizer Coupling on Growth Characteristics and Water Use Efficiency of Camellia petelotii Seedlings

Camellia petelotii(Merr.)Sealy is an endangered Chinese native species that originates from Guangxi Zhuang Autonomous Region,China.Previous research demonstrated that proper water and fertilizer treatments could improve the growth and quality of Camellia species.This study uses a three-factor,five-level quadratic rotational combination experimental design to investigate the impact of water-fertilizer coupling on plant growth character-istics and the most suitable treatment for 24-month-old grafted C.petelotii seedlings.The experimental design includes irrigation levels[30%,40%,55%,70%,80%offield capacity(FC)],nitrogen application(0,2.17,5.43,8.70,10.87 g·plant^(-1)),and phosphorus application(0,0.96,2.40,3.85,4.81 g·plant^(-1)).The results indicated that:(1)Water-nitrogen and water-phosphorus interactions significantly affected ground diameter,chlorophyll content and specific leaf weight(SLW),while water-nitrogen interactions significantly affected plant height and photo-synthesis;(2)Application of nitrogen(8.70 g·plant^(-1))and phosphorus(3.85 g·plant^(-1))fertilizers under appropri-ate irrigation conditions(40%FC and 70%FC)improved growth.Applying fertilizers containing either nitrogen(10.87 g·plant^(-1))or phosphorus(4.81 g·plant^(-1))under adequate irrigation(55%FC)increased the Chl content.However,high nitrogen levels(10.87 g·plant^(-1))reduced photosynthesis.Conversely,it was enhanced under appropriate phosphorus(4.81 g·plant^(-1))when the irrigation level was 55%FC,indicating the sensitivity of C.pete-lotii seedlings to nitrogen fertilizer.(3)Under specific conditions of 40%FC or 70%FC irrigation and 8.70 g·plant^(-1) or 2.17 g·plant^(-1) nitrogen fertilizer application,3.85 g·plant^(-1) phosphorus addition boosted the SLW whereas,0.96 g·plant^(-1) phosphorus addition inhibited it.Under W=55%FC,deficiencies in either nitrogen(N=0 g·plant^(-1))or phosphorus(P=0 g·plant^(-1))significantly decreased leaf growth,affecting SLW.In summary,C.petelotii was more sensitive to nitrogen fertilizer at W=55%FC,and nitrogen deficiency inhibited C.petelotii growth in terms of ground diameter more than phosphorus deficiency.The C.petelotii seedlings performed best when treated with 55%FC,5.43 g·plant^(-1) nitrogen,2.40 g·plant^(-1) phosphorus per plant.These parameter esti-mates could optimize water and fertilizer application for C.petelotii seedlings.

Regulation effects of water and nitrogen on yield,water,and nitrogen use efficiency of wolfberry

Wolfberry(Lycium barbarum L.)is important for health care and ecological protection.However,it faces problems of low productivity and resource utilization during planting.Exploring reasonable models for water and nitrogen management is important for solving these problems.Based on field trials in 2021 and 2022,this study analyzed the effects of controlling soil water and nitrogen application levels on wolfberry height,stem diameter,crown width,yield,and water(WUE)and nitrogen use efficiency(NUE).The upper and lower limits of soil water were controlled by the percentage of soil water content to field water capacity(θ_(f)),and four water levels,i.e.,adequate irrigation(W0,75%-85%θ_(f)),mild water deficit(W1,65%-75%θ_(f)),moderate water deficit(W2,55%-65%θ_(f)),and severe water deficit(W3,45%-55%θ_(f))were used,and three nitrogen application levels,i.e.,no nitrogen(N0,0 kg/hm^(2)),low nitrogen(N1,150 kg/hm^(2)),medium nitrogen(N2,300 kg/hm^(2)),and high nitrogen(N3,450 kg/hm^(2))were implied.The results showed that irrigation and nitrogen application significantly affected plant height,stem diameter,and crown width of wolfberry at different growth stages(P<0.01),and their maximum values were observed in W1N2,W0N2,and W1N3 treatments.Dry weight per plant and yield of wolfberry first increased and then decreased with increasing nitrogen application under the same water treatment.Dry weight per hundred grains and dry weight percentage increased with increasing nitrogen application under W0 treatment.However,under other water treatments,the values first increased and then decreased with increasing nitrogen application.Yield and its component of wolfberry first increased and then decreased as water deficit increased under the same nitrogen treatment.Irrigation water use efficiency(IWUE,8.46 kg/(hm^(2)·mm)),WUE(6.83 kg/(hm^(2)·mm)),partial factor productivity of nitrogen(PFPN,2.56 kg/kg),and NUE(14.29 kg/kg)reached their highest values in W2N2,W1N2,W1N2,and W1N1 treatments.Results of principal component analysis(PCA)showed that yield,WUE,and NUE were better in W1N2 treatment,making it a suitable water and nitrogen management mode for the irrigation area of the Yellow River in the Gansu Province,China and similar planting areas.

Development,hotspots and trend directions of groundwater numerical simulation:A bibliometric and visualization analysis

Groundwater is a vital component of the hydrological cycle and essential for the sustainable development of ecosystems.Numerical simulation methods are key tools for addressing scientific challenges in groundwater research.This study uses bibliometric visualization analysis to examine the progress and trends in groundwater numerical simulation methods.By analyzing literature indexed in the Web of Science database from January 1990 to February 2023,and employing tools such as Citespace and VOSviewer,we assessed publication volume,research institutions and their collaborations,prolific scholars,keyword clustering,and emerging trends.The findings indicate an overall upward trend in both the number of publications and citations concerning groundwater numerical simulations.Since 2010,the number of publications has tripled compared to the total before 2010,underscoring the increasing significance and potential of numerical simulation methods in groundwater science.China,in particular,has shown remarkable growth in this field over the past decade,surpassing the United States,Canada,and Germany.This progress is closely linked to strong national support and active participation from research institutions,especially the contributions from teams at Hohai University,China University of Geosciences,and the University of Science and Technology of China.Collaboration between research teams is primarily seen between China and the United States,with less noticeable cooperation among other countries,resulting in a diverse and dispersed development pattern.Keyword analysis highlights that international research hotspots include groundwater recharge,karst water,geothermal water migration,seawater intrusion,variable density flow,contaminant and solute transport,pollution remediation,and land subsidence.Looking ahead,groundwater numerical simulations are expected to play a more prominent role in areas such as climate change,surface water-groundwater interactions,the impact of groundwater nitrates on the environment and health,submarine groundwater discharge,ecological water use,groundwater management,and risk prevention.