Physical Investigation of Directional Wave Focusing and Breaking Waves in Wave Basin

An experimental scheme for the generation of directional focusing waves in a wave basin is established in this paper. The effects of the directional range, frequency width and center frequency on the wave focusing are studied. The distribution of maximum amplitude and the evolution of time series and spectra during wave packet propagation and the variation of water surface parameters are extensively investigated. The results reveal that the characteristics of focusing waves are significantly influenced by wave directionality and that the breaking criteria for directional waves are distinctly different from those for unidirectional waves.

Effects of wave propagation anisotropy on the wave focusing by negative refractive sonic crystal flat lenses

In this study, wave propagation anisotropy in a triangular lattice crystal structure and its associated waveform shaping in a crystal structure are investigated theoretically. A directional variation in wave velocity inside a crystal structure is shown to cause bending wave envelopes. The authors report that a triangular lattice sonic crystal possesses six numbers of a high symmetry direction, which leads to a wave convergence caused by wave velocity anisotropy inside the crystal. However, two of them are utilized mostly in wave focusing by an acoustic fiat lens. Based on wave velocity anisotropy, the pseudo ideal imaging effect obtained in the second band of the flat lens is discussed.

Deflagration and detonation induced by shock wave focusing at different Mach numbers

Shock wave focusing is an effective way to create a hot spot or a high-pressure and hightemperature region at a certain place,showing its unique usage in detonation initiation,which is beneficial for the development of detonation-based engines.The flame propagation behavior after the autoignition induced by shock wave focusing is crucial to the formation and self-sustaining of the detonation wave.In this study,wedge reflectors with two different angles(60°and 90°)and a planar reflector are employed,and the Mach number of incident shock waves ranging from 2.0 to 2.8 is utilized to trigger different flame propagation modes.Dynamic pressure transducers and the high-speed schlieren imaging system are both employed to investigate the shock-shock collision and ignition procedure.The results reveal a total of four flame propagation modes:deflagration,DDT(Deflagration-to-Detonation Transition),unsteady detonation,and direct detonation.The detonation wave formed in the DDT and unsteady detonation mode is only approximately 75%-85%of the Chapman-Jouguet(C-J)speed;meanwhile,the directly induced detonation wave speed is close to the C-J speed.Transverse waves,which are strong evidence for the existence of detonation waves,are discovered in experiments.The usage of wedge reflectors significantly reduces the initial pressure difference ratio needed for direct detonation ignition.We also provide a practical method for differentiating between detonation and deflagration modes,which involves contrasting the speed of the reflected shock wave with the speed of the theoretically nonreactive reflected shock wave.These findings should serve as a reference for the detonation initiation technique in advanced detonation propulsion engines.

Efficient Focusing Models for Generation of Freak Waves

Four focusing models for generation of freak waves are presented. An extreme wave focusing model is presented on the basis of the enhanced High-Order Spectral （HOS） method and the importance of the nonlinear wave-wave interaction is evaluated by comparison of the calculated results with experimental and theoretical data. Based on the modification of the Longuet-Higgins model, four wave models for generation of freak waves （a. extreme wave model ＋ random wave model; b. extreme wave model ＋ regular wave model; e. phase interval modulation wave focusing model; d. number modulation wave focusing model with the same phase） are proposed. By use of different energy distribution techniques in the four models, freak wave events are obtained with different Hmax/Hs in finite space and time.

Experimental Study on 2-D Focusing Wave Run-up on A Vertical Cylinder

In this paper,the focused wave groups with different parameters and their actions on a vertical cylinder are experimentally studied. The harmonic wave characteristics of the focusing waves are analyzed by the addition and subtraction of the crest and trough focusing waves. The analyzed results show that higher order harmonics can be generated because of the interaction of component waves. Nonlinearity increases with the inputted wave amplitude and the frequency width increment. Further, the wave run-up around the vertical circular cylinder is experimentally studied. It increases with the wave steepness and the relative cylinder diameter increase. However, the variations of wave run-up around the circular cylinder are different. The researches provide a reference for further numerical studies.

An efficient focusing model for generation of freak waves

Based on the Longuet-Higgins wave model theory, the previews studies have shown that freak waves can be generated in finite space and time successfully. However, as to generating high nonlinear freak waves, the simulation results will be unrealistic. Therefore, a modified phase modulation method for simulating high nonlinear freak waves was developed. The surface elevations of some wave components at certain time and place are positive by modulating the corresponding random initial phases, then the total surface elevation at the focused point is enhanced and furthermore a freak wave event is generated. The new method can not only make the freak wave occur at certain time and place, but also make the simulated wave surface time series satisfy statistical properties of the realistic sea state and keep identical with the target wave spectrum. This numerical approach is of good precision and high efficiency by the comparisons of the simulated freak waves and the recorded freak waves.

The influence of radial entrance width of the circular cavity on incident shock wave focusing

Despite the achievement of shock wave focusing with certain reflectors,the influence of the radial entrance width of a circular cavity on the flow field has yet to be addressed.In this study,we systematically investigated the effects of the shock wave focusing process in a cavity based on the radial entrance widths.An experimental system was installed to research the evolution of the flow field under conditions with different radial entrance widths of 3.0,11.1,19.5,and 33.0 mm.A schlieren system was used to photograph the structures of the flow field in the cavity,and a data acquisition system was used to record the dynamic pressure histories of different points.A numerical simulation was carried out to investigate greater details of the shock wave focusing process.A third-order strong stability-preserving Runge-Kutta method,third-order weighed essential non-oscillation scheme,and an adaptive mesh refinement algorithm were adopted to simulate the shock wave reflection,diffraction,and focus process.Good agreement between the experimental and numerical results was observed.By comparing the evolution process of the flow field under the conditions of four different entrance cavity widths,we found that when the entrance width was 19.5 mm,there was the stronger intensity of the shock wave focusing in the focal region,and the larger pressure value at the apex of the cavity than the other three entrance widths,occur.This study improves our understanding of shock wave focusing.

Numerical Study of Two-Dimensional Focusing Waves

Two-dimensional focusing waves are generated and investigated by numerical method. The numerical model is developed by introducing the wave maker boundary on the high-order spectral （HOS） method proposed by Dommermuth and Yue in 1987 and verified by theoretical and experimental data. Some cases of focusing waves considering different parameters such as assumed focusing amplitudes, frequency bandwidth, central frequency and frequency spectrum are generated. Characteristics of the focusing wave including surface elevations, the maximum crest, shift of focusing points and frequency spectra are discussed. The results show that the focusing wave characteristics are strongly affected by focusing amplitudes, frequency bandwidth, central frequency and frequency spectrum.

Numerical Study of Influence of Currents on Nonlinear Focusing Waves

In this paper, a numerical model for nonlinear wave propagation in currents is formulated by a set of enhanced fully nonlinear Boussinesq equations with ambient currents. This model is verified by comparison with the published results. Then the influence of currents on nonlinear focusing waves is studied by use of the numerical model. It is found that the effect of currents on the surface elevations at the fecal location is negligible. Following currents can augment the maximum crest of focusing wave while decrease the focusing time, and vice versa for opposing currents. Furthermore, both opposing and following currents can shift the focal location forward relative to that in quiescent water.

Influences of Floater Motion on Gap Resonance Triggered by Focused Wave Groups

The current study investigates the hydrodynamic characteristics of gap resonance within a narrow gap formed by two adjacent boxes subjected to incident focused transient wave groups.A two-dimensional(2D)numerical wave tank based on the OpenFOAM package is utilized for this purpose.The weather-side box is fixed while the lee-side box is allowed to heave freely under wave actions.The effects of the focused wave amplitude and spectral peak period on the wave amplification within the gap,motion of the lee-side box,and wave forces(including horizontal and vertical wave forces)acting on each box are systematically examined.For comparison,another structural layout consisting of two fixed boxes is also considered.The results reveal that the release of the heave degree of freedom(DoF)of the lee-side box results in remarkably distinct resonance features.In the heave-box system,both its fluid resonant period and the period corresponding to the maximum heave displacement of the lee-side box are significantly larger(i.e.,1.6-1.7 times)than the fluid resonant period of the fixed-box system.However,the wave amplification factor inside the gap in the heave-box system is significantly lower than that in the fixed-box one.Both the variations of the maximum horizontal and vertical wave forces with the spectral peak period and their magnitudes are also significantly different between the two structural systems.

An analytical approximation of focusing-wave-induced load on a semi-submerged cylinder

Owing to the complexity of the physical mechanisms of rouge waves,the theoretical study of the rogue-wavestructure interaction problems still makes little progress.However,for regular-shaped structures,it is possible to give a theoretical analysis,if a relatively simple model of the rogue waves is used.The wave load,induced by a focusing wave which is known as an intuitive basic model of the rouge waves,upon a semi-submerged cylinder is studied analytically.The focusing wave is approximate by the Gauss envelope wave,an ideal model which contains most features of the rogue wave.The diffraction velocity potential is derived through the separation of flow field,and the formulas of the horizontal force and bending moment are proposed.The derived formulas are simplified appropriately,and validated through comparison against numerical results.In addition,the influence of parameters,such as the focusing degree,the submerging depth and the wave focusing position,is thoroughly investigated.

Simulation of Horizontal-Two-Dimension Focused Waves Using A Two-Layer Boussinesq-Type Model

Accurate simulation of the horizontal-two-dimension(H2D)focused wave group in deep water requires high accuracy of a numerical model.The two-layer Boussinesq-type model(Liu and Fang,2016;Liu et al.,2018)with the highest spatial derivative of 2 has high accuracy in both linear and nonlinear properties.Based on the further development of the velocity equations(Liu et al.,2023),the H2D numerical model for water waves is established with the prediction-correction-iteration model in the finite difference method,and a composite fourth-order Adams-Bashforth-Moulton scheme is used for time integration.The wave generation method proposed by Hsiao et al.(2005)is applied and calibrated in this H2D model.The numerical calculations lead to the following three main conclusions:First,compared with the analytical solution of Stokes linear waves,the calculated velocity profiles show higher accuracy by using the improved velocity formulas.Second,the simulations of the focused multidirectional wave group are carried out,and good agreements are found,demonstrating that the present H2D numerical model shows high accuracy in simulating focused multidirectional wave groups,and the effectiveness of the improved velocity formulas is also validated.Furthermore,the velocity profiles throughout the computational domain at the time of maximum wave crest are given.Finally,the FFT method is used to obtain the amplitude with different frequencies for several locations,and the changes of the wavelet energy spectrum at different locations are presented for several cases.

Generation and Properties of Freak Waves in A Numerical Wave Tank

Freak waves are generated based on the mechanism of wave focusing in a 2D numerical wave tank. To set up the nonlinear numerical wave tank, the Boundary Element Method is used to solve potential flow equations incorporated with fully nonlinear free surface boundary conditions. The nonlinear properties of freak waves, such as high frequency components and wave profile asymmetry, are discussed. The kinematic data, which can be useful for the evaluation of the wave forces exerted on structures to avoid underestimation of linear predictions, are obtained, and discussed, from the simulated results of freak waves.

Numerical modelling of nonlinear extreme waves in presence of wind

A numerical wave flume with fully nonlinear free surface boundary conditions is adopted to investigate the temporal characteristics of extreme waves in the presence of wind at various speeds. Incident wave trains are numerically generated by a piston-type wave maker, and the wind-excited pressure is introduced into dynamic boundary conditions using a pressure distribution over steep crests, as defined by Jeffreys＇ sheltering mechanism.A boundary value problem is solved by a higher-order boundary element method（HOBEM） and a mixed Eulerian-Lagrangian time marching scheme. The proposed model is validated through comparison with published experimental data from a focused wave group. The influence of wind on extreme wave properties,including maximum extreme wave crest, focal position shift, and spectrum evolution, is also studied. To consider the effects of the wind-driven currents on a wave evolution, the simulations assume a uniform current over varying water depth. The results show that wind causes weak increases in the extreme wave crest, and makes the nonlinear energy transfer non-reversible in the focusing and defocusing processes. The numerical results also provide a comparison to demonstrate the shifts at focal points, considering the combined effects of the winds and the wind-driven currents.

Theoretical demonstration of the hybrid focusing points of sonic crystal flat lenses and possible applications

We demonstrate the hybrid focusing points of sonic crystals for a multi-source array applied to flat sonic crystal lenses. The contributions of different point source couples form hybrid focusing points. Ray-trace analyses are conducted for acoustic flat lenses with multi-source configurations. The finite-difference time-domain （FDTD） simulation of flat lenses with multi-source configurations demonstrates the establishment of pure and hybrid focusing points in a pyramidal constellation. The number of focusing points in the pyramidal constellation depends on the number of point sources. We propose an acoustic device for fine-tuning the location of a far-field hybrid focusing point and discuss its benefits for acoustic energy focusing application.

Extreme Wave Simulation with Iterative Adaptive Approach in Numerical Wave Flume

Extreme wave is highly nonlinear and may occur due to diverse reasons unexpectedly.The simulated results of extreme wave based on wave focusing,which were generated using high order spectrum method,are presented.The influences of the steepness,frequency bandwidth as well as frequency spectrum on focusing position shift were examined,showing that they can affect the wave focusing significantly.Hence,controlled accurate generation of extreme wave at a predefined position in wave flume is a difficult but important task.In this paper,an iterative adaptive approach is applied using linear dispersion theory to optimize the control signal of the wavemaker.The performance of the proposed approach is numerically investigated for a wide variety of scenarios.The results demonstrate that this approach can reproduce accurate wave focusing effectively.

3-D simulations of freak waves based on high-order spectral method

Three-dimensional ( 3-D) directional wave focusing is one of the mechanisms that contribute to the generation of freak waves. To simulate and analyze this phenomenon,a 3-D wave focusing model is proposed based on the enhanced high-order spectral method,which solves the fully nonlinear potential flow equations with a free surface within periodic unbounded 3-D domains. The numerical model is validated against a fifth-order Stokes solution for regular waves. Laboratory-scale freak waves are observed with wave components having equal amplitudes. Investigations of the appearance and propagation of freak-wave events in a 3-D open wavefield defined by a directional wave spectrum are then realized.

Focused Wave Properties Based on A High Order Spectral Method with A Non-Periodic Boundary

In this paper, a numerical model is developed based on the High Order Spectral （HOS） method with a non-periodic boundary. A wave maker boundary condition is introduced to simulate wave generation at the incident boundary in the HOS method. Based on the numerical model, the effects of wave parameters, such as the assumed focused amplitude, the central frequency, the frequency bandwidth, the wave amplitude distribution and the directional spreading on the surface elevation of the focused wave, the maximum generated wave crest, and the shifting of the focusing point, are numerically investigated. Especially, the effects of the wave directionality on the focused wave properties are emphasized. The numerical results show that the shifting of the focusing point and the maximum crest of the wave group are dependent on the amplitude of the focused wave, the central frequency, and the wave amplitude distribution type. The wave directionality has a definite effect on multidirectional focused waves. Generally, it can even out the difference between the simulated wave amplitude and the amplitude expected from theory and reduce the shifting of the focusing points, implying that the higher order interaction has an influence on wave focusing, especially for 2D wave. In 3D wave groups, a broader directional spreading weakens the higher nonlinear interactions.

Nonlinear Dynamic Behaviors of A Floating Structure in Focused Waves

Floating structures are commonly seen in coastal and offshore engineering. They are often subjected to extreme waves and, therefore, their nonlinear dynamic behaviors are of great concern. In this paper, an in-house CFD code is developed to investigate the accurate prediction of nonlinear dynamic behaviors of a two-dimensional（2-D） box-shaped floating structure in focused waves. Computations are performed by an enhanced Constrained Interpolation Profile（CIP）-based Cartesian grid model, in which a more accurate VOF（Volume of Fluid） method, the THINC/SW scheme（THINC： tangent of hyperbola for interface capturing; SW： Slope Weighting）, is used for interface capturing. A focusing wave theory is used for the focused wave generation. The wave component of constant steepness is chosen. Comparisons between predictions and physical measurements show good agreement including body motions and free surface profiles. Although the overall agreement is good, some discrepancies are observed for impact pressure on the superstructure due to water on deck. The effect of grid resolution on the results is checked. With a fine grid, no obvious improvement is seen in the global body motions and impact pressures due to water on deck. It is concluded that highly nonlinear phenomena, such as distorted free surface, large-amplitude body motions, and violent impact flow, have been predicted successfully.

An Efficient Model for Transient Surface Waves in Both Finite and Infinite Water Depths

A numerical model is developed to simulate fully nonlinear extreme waves in finite and infinite water-depth wave tanks. A semi-mixed Enlerian-Lagrangian formulation is adopted and a higher-order boundary element method in conjunction with an image Green function is used for the fluid domain. The botmdary values on the free surface are updated at each time step by a fourth-order Runga-Kutta time-marching scheme at each time step. Input wave characteristics are specified at the upstream boundary by an appropriate wave theory. At the downstream boundary, an artificial damping zone is used to prevent wave reflection back into the computational domain. Using the image Green function in the whole fluid domain, the integrations on the two lateral walls and bottom are excluded. The simulation results on extreme wave elevations in finite and infinite water-depths are compared with experimental results and second-order analytical solutions respectively. The wave kinematics is also discussed in the present study.