In this paper, toughness properties and microstructurc of low-alloyed multipass welds with yield strength above 700MPa have 6een studied using the weld thermal simulation and throughout thickness CTOD fracture mechani...In this paper, toughness properties and microstructurc of low-alloyed multipass welds with yield strength above 700MPa have 6een studied using the weld thermal simulation and throughout thickness CTOD fracture mechanics tests. Impact testing of thermal simulated specimens showed that the primary weld metal and the fine gmmed weld metal had good toughness, while the coarse grained weld metal had the lowest toughness value as the local brittle zone (LBZ) in multipass weld metals. Cleavage fracture in CTOD testing of thick multipass weld metals was initiated from martensite-austenite (MA) phases in the LBZ. MA phases were distributed at the prior austenite grain boundaries and around ferrite grains. As the size of the local brittle zone along the fatigue crack front increases, CTOD frncture toughness of multipass weld metals decreases. The weakest link theory was used to evaluate effect of the local brittle zone on fracture toughness of thick multipass weld metals. The estimated curves agree well with the eaperimental data.展开更多
By using thermo-simulation,Auger analysis and Charpy Ⅴ impact test and with the observation of the microstructures in which cleavage crack was initiated,the morphology and toughness of the local brittle zone of C-Mn ...By using thermo-simulation,Auger analysis and Charpy Ⅴ impact test and with the observation of the microstructures in which cleavage crack was initiated,the morphology and toughness of the local brittle zone of C-Mn and Cr-Ni-Mo multipass weld metals have been investigated.The results indicated that the local brittle zone in C-Mn weld metals with low and high Mn％ and Cr- Ni-Mo weld metals is different.With statistical analysis,it has been revealed that the more the local brittle zone and the lower their toughness,the lower the toughness of the entire weld metals.The alloy elements have a noticeable influ- ence on the toughness of the local brittle zone,thereby changing the toughness of weld metals.展开更多
Metal active gas （ MAG） welding has been carried out on microalloy controlled rolling steel （S355J2W） by two kinds of welding wires with different Ti content. The mechanical tests have been carried out on the weld...Metal active gas （ MAG） welding has been carried out on microalloy controlled rolling steel （S355J2W） by two kinds of welding wires with different Ti content. The mechanical tests have been carried out on the welded joint. The optical microscope and scanning electron microscope （SEM） observations have been performed to investigate the effect of microalloy element Ti on the microstructure of weld metal and impact fracture, respectively. The microstrueture of the MAG multipass weld metal includes the columnar grain zone （CGZ） consisting of primary ferrite （ PF）, ferrite with second phase （FS） and acicularferrite （AF）, and the fine grain zone （FGZ） consisting of polygonal ferrite due to the heat effect of subsequent welding pass. It has been found that the small amount of Ti can significantly increase the impact energy of the weld metal at low temperature and weakly affect tensile strength of welded joint. By adding small amount of Ti, the inclusions have changed from Mn-Si-O inclusions to Ti-bearing inclusions, which causes the Mn-depleted zones（MDZs） much larger and is beneficial to the impact energy by promoting the AF formation, refining the PF and pinning the austenite grain boundary during the subsequent transformation process.展开更多
Different investigations of the union of dissimilar materials such as stainless steel and different castings have been carried out, but rapid cooling immediately after welding has not been considered, in this work it ...Different investigations of the union of dissimilar materials such as stainless steel and different castings have been carried out, but rapid cooling immediately after welding has not been considered, in this work it was investigated how rapid cooling affects the metallurgical microstructure and consequently the mechanical properties. The effect of welding parameters on the microstructure and mechanical properties of the joint between dissimilar metals, an E-308-16 austenitic stainless steel and Gray Cast Iron was also analyzed. Gray cast iron samples (GCI) were fabricated, welded and cooled. The main welding parameters studied in this work are the welding technique and the type of filler electrodes. Flux-coated electrode E-308-16 was applied for this different joint. An experimental study was carried out for the analysis of welded joints of similar and dissimilar steels. The microstructure of the welded joints was analyzed using an optical microscope, in the base metals, heat affected zone (HAZ) and filler metal. The mechanical properties of the welded joints were evaluated by Vickers microhardness and tensile strength tests. The hardness profile showed differences in hardness between the base metals, the heat affected zone and the filler metal. The metallurgical microstructures observed along the welded areas corresponded to the profile. The hardness differences determined the effect on the mechanical and metallurgical characteristics of the welded samples as a result of the cooling rate differences. This research work is important because it allows us to analyze the possibility of reworking pieces of dissimilar materials by welding or, failing that, to determine if this may or may not be possible.展开更多
Austenitic stainless steel(ASS) and High nickel steel(HNS) welding consumables are being used for welding Q&T steels, as they have higher solubility for hydrogen in austenitic phase, to avoid hydrogen induced crac...Austenitic stainless steel(ASS) and High nickel steel(HNS) welding consumables are being used for welding Q&T steels, as they have higher solubility for hydrogen in austenitic phase, to avoid hydrogen induced cracking(HIC) but they are very expensive. In recent years, the developments of low hydrogen ferritic steel(LHF) consumables that contain no hygroscopic compounds are utilized for welding Q&T steels. Heat affected zone(HAZ) softening is another critical issue during welding of armour grade Q&T steels and it depends on the welding process employed and the weld thermal cycle. In this investigation an attempt has been made to study the influence of welding consumables and welding processes on metallurgical characteristics of armour grade Q&T steel joints by various metallurgical characterization procedures. Shielded metal arc welding(SMAW) and flux cored arc welding(FCAW) processes were used for making welds using ASS, LHF and HNS welding consumables. The joints fabricated by using LHF consumables offered lower degree of HAZ softening and there is no evidence of HIC in the joints fabricated using LHF consumables.展开更多
In this work, the effect of heat input on the mechanical properties of low-carbon steel was studied using two welding processes: Oxy-Acetylene Welding (OAW) and Shielded Metal Arc Welding (SMAW). Two different edge pr...In this work, the effect of heat input on the mechanical properties of low-carbon steel was studied using two welding processes: Oxy-Acetylene Welding (OAW) and Shielded Metal Arc Welding (SMAW). Two different edge preparations on a specific size, 10-mm thick low-carbon steel, with the following welding parameters: dual welding voltage of 100 V and 220 V, various welding currents at 100, 120, and 150 Amperes and different mild steel electrode gauges of 10 and 12 were investigated. The tensile strength, hardness and impact strength of the welded joint were carried out and it was discovered that the tensile strength and hardness reduce with the increase in heat input into the weld. However, the impact strength of the weldment increases with the increase in heat input. Besides it was also discovered that V-grooved edge preparation has better mechanical properties as compared with straight edge preparation under the same conditions. Microstructural examinations conducted revealed that the cooling rate in different media has significant effect on the microstructure of the weldment. Pearlite and ferrite were observed in the microstructure, but the proportion of ferrite to pearlite varied under different conditions.展开更多
This paper presents the study carried out to study the microstructure and mechanical properties of AISI 304 stainless steel and gray iron, in order to recognize the effect of welding parameters on the joint. The shiel...This paper presents the study carried out to study the microstructure and mechanical properties of AISI 304 stainless steel and gray iron, in order to recognize the effect of welding parameters on the joint. The shielded metal arc welding technique was applied with a 3.2 mm diameter nickel coated electrode under preheating and post heat conditions at 350°C. Vickers hardness test and metallographic analysis were carried out at the heat affected zone and at the interface to determine the effect on mechanical and metallurgical characteristics. Vickers hardness differences among joint areas were directly related to microstructural changes. There are no significant differences in AISI 304 hardness, but the hardness increased at the heat affected zone and decreased at the filler metal. Grey iron hardness at the heat affected zone was even lower and more slightly superior than grey iron hardness.展开更多
文摘In this paper, toughness properties and microstructurc of low-alloyed multipass welds with yield strength above 700MPa have 6een studied using the weld thermal simulation and throughout thickness CTOD fracture mechanics tests. Impact testing of thermal simulated specimens showed that the primary weld metal and the fine gmmed weld metal had good toughness, while the coarse grained weld metal had the lowest toughness value as the local brittle zone (LBZ) in multipass weld metals. Cleavage fracture in CTOD testing of thick multipass weld metals was initiated from martensite-austenite (MA) phases in the LBZ. MA phases were distributed at the prior austenite grain boundaries and around ferrite grains. As the size of the local brittle zone along the fatigue crack front increases, CTOD frncture toughness of multipass weld metals decreases. The weakest link theory was used to evaluate effect of the local brittle zone on fracture toughness of thick multipass weld metals. The estimated curves agree well with the eaperimental data.
文摘By using thermo-simulation,Auger analysis and Charpy Ⅴ impact test and with the observation of the microstructures in which cleavage crack was initiated,the morphology and toughness of the local brittle zone of C-Mn and Cr-Ni-Mo multipass weld metals have been investigated.The results indicated that the local brittle zone in C-Mn weld metals with low and high Mn％ and Cr- Ni-Mo weld metals is different.With statistical analysis,it has been revealed that the more the local brittle zone and the lower their toughness,the lower the toughness of the entire weld metals.The alloy elements have a noticeable influ- ence on the toughness of the local brittle zone,thereby changing the toughness of weld metals.
文摘Metal active gas （ MAG） welding has been carried out on microalloy controlled rolling steel （S355J2W） by two kinds of welding wires with different Ti content. The mechanical tests have been carried out on the welded joint. The optical microscope and scanning electron microscope （SEM） observations have been performed to investigate the effect of microalloy element Ti on the microstructure of weld metal and impact fracture, respectively. The microstrueture of the MAG multipass weld metal includes the columnar grain zone （CGZ） consisting of primary ferrite （ PF）, ferrite with second phase （FS） and acicularferrite （AF）, and the fine grain zone （FGZ） consisting of polygonal ferrite due to the heat effect of subsequent welding pass. It has been found that the small amount of Ti can significantly increase the impact energy of the weld metal at low temperature and weakly affect tensile strength of welded joint. By adding small amount of Ti, the inclusions have changed from Mn-Si-O inclusions to Ti-bearing inclusions, which causes the Mn-depleted zones（MDZs） much larger and is beneficial to the impact energy by promoting the AF formation, refining the PF and pinning the austenite grain boundary during the subsequent transformation process.
文摘Different investigations of the union of dissimilar materials such as stainless steel and different castings have been carried out, but rapid cooling immediately after welding has not been considered, in this work it was investigated how rapid cooling affects the metallurgical microstructure and consequently the mechanical properties. The effect of welding parameters on the microstructure and mechanical properties of the joint between dissimilar metals, an E-308-16 austenitic stainless steel and Gray Cast Iron was also analyzed. Gray cast iron samples (GCI) were fabricated, welded and cooled. The main welding parameters studied in this work are the welding technique and the type of filler electrodes. Flux-coated electrode E-308-16 was applied for this different joint. An experimental study was carried out for the analysis of welded joints of similar and dissimilar steels. The microstructure of the welded joints was analyzed using an optical microscope, in the base metals, heat affected zone (HAZ) and filler metal. The mechanical properties of the welded joints were evaluated by Vickers microhardness and tensile strength tests. The hardness profile showed differences in hardness between the base metals, the heat affected zone and the filler metal. The metallurgical microstructures observed along the welded areas corresponded to the profile. The hardness differences determined the effect on the mechanical and metallurgical characteristics of the welded samples as a result of the cooling rate differences. This research work is important because it allows us to analyze the possibility of reworking pieces of dissimilar materials by welding or, failing that, to determine if this may or may not be possible.
基金Armament Research Board (ARMREB), New Delhi for funding this project work (Project no. MAA/03/ 41)
文摘Austenitic stainless steel(ASS) and High nickel steel(HNS) welding consumables are being used for welding Q&T steels, as they have higher solubility for hydrogen in austenitic phase, to avoid hydrogen induced cracking(HIC) but they are very expensive. In recent years, the developments of low hydrogen ferritic steel(LHF) consumables that contain no hygroscopic compounds are utilized for welding Q&T steels. Heat affected zone(HAZ) softening is another critical issue during welding of armour grade Q&T steels and it depends on the welding process employed and the weld thermal cycle. In this investigation an attempt has been made to study the influence of welding consumables and welding processes on metallurgical characteristics of armour grade Q&T steel joints by various metallurgical characterization procedures. Shielded metal arc welding(SMAW) and flux cored arc welding(FCAW) processes were used for making welds using ASS, LHF and HNS welding consumables. The joints fabricated by using LHF consumables offered lower degree of HAZ softening and there is no evidence of HIC in the joints fabricated using LHF consumables.
文摘In this work, the effect of heat input on the mechanical properties of low-carbon steel was studied using two welding processes: Oxy-Acetylene Welding (OAW) and Shielded Metal Arc Welding (SMAW). Two different edge preparations on a specific size, 10-mm thick low-carbon steel, with the following welding parameters: dual welding voltage of 100 V and 220 V, various welding currents at 100, 120, and 150 Amperes and different mild steel electrode gauges of 10 and 12 were investigated. The tensile strength, hardness and impact strength of the welded joint were carried out and it was discovered that the tensile strength and hardness reduce with the increase in heat input into the weld. However, the impact strength of the weldment increases with the increase in heat input. Besides it was also discovered that V-grooved edge preparation has better mechanical properties as compared with straight edge preparation under the same conditions. Microstructural examinations conducted revealed that the cooling rate in different media has significant effect on the microstructure of the weldment. Pearlite and ferrite were observed in the microstructure, but the proportion of ferrite to pearlite varied under different conditions.
文摘This paper presents the study carried out to study the microstructure and mechanical properties of AISI 304 stainless steel and gray iron, in order to recognize the effect of welding parameters on the joint. The shielded metal arc welding technique was applied with a 3.2 mm diameter nickel coated electrode under preheating and post heat conditions at 350°C. Vickers hardness test and metallographic analysis were carried out at the heat affected zone and at the interface to determine the effect on mechanical and metallurgical characteristics. Vickers hardness differences among joint areas were directly related to microstructural changes. There are no significant differences in AISI 304 hardness, but the hardness increased at the heat affected zone and decreased at the filler metal. Grey iron hardness at the heat affected zone was even lower and more slightly superior than grey iron hardness.
