The numerical analysis of thermal effect and weld shaping of DE-GMAW under composite heat source

The action of the composite heat source model in DE-GMAW has been carried out according to the characteristics of the DE-GMA W process, and the distribution of surface and body heat source was analyzed. The weld temperature field distribution has been derived from the appropriate boundary conditions and the thermal physical property parameters by COMSOL software. The effects of the positions of the surface and body heat source on the cross- sectional shape were investigated by studying the experimental welding thermal cycle curve. The simulated results are fully compliant with the experimental data under the same conditions. This illustrates that the composite heat source model is correct. It reflects the thermal mechanism of DE-GMA W process, and reveals the internal influence of weld shaping.

YAG laser welding with surface activating flux

YAG laser welding with surface activating flux has been investigated, and the influencing factors and mechanism are discussed. The results show that both surface activating flux and surface active element S have fantastic effects on the YAG laser weld shape, that is to obviously increase the weld penetration and D/W ratio in various welding conditions. The mechanism is thought to be the change of weld pool surface tension temperature coefficient, thus, the change of fluid flow pattern in weld pool due to the flux.

Time Dependant Weld Shape in Ar-O_2 Shielded Stationary GTA Welding

The stationary gas tungsten arc welding （GTA） is carried out on SUS304 stainless steel under Ar-0.1%O2 and Ar-0.3%O2 mixed shielding to observe the evolution of the molten pool and investigate the role of Marangoni convection on the weld shape. After welding, the oxygen content in the weld metal was measured by using an oxygen/nitrogen analyzer. Small addition of oxygen to the argon based shielding gas can effectively adjust the weld pool oxygen content. Oxygen plays an important role as an surface active element in determining the pattern of Marangoni convection in the stainless steel weld pool. When the weld metal oxygen content is over the critical value, 0.01 wt pct, corresponding to the Ar-0.3%O2 mixed shielding gas, the Marangoni convection changes from outward to inward direction and the weld shape dramatically changes from wide shallow shape to narrow deep shape.

Effect of laser characteristics on the weld shape and properties of penetration laser weld of BT20 titanium alloy

The laser beam welding of BT20 titanium alloy was conducted to investigate the weld shape, microstructures and properties. The full penetration weld characteristics produced by CO_2 laser and by YAG laser were compared. The results show that the full penetration weld of YAG laser welding closes to “X” shape, and weld of CO_2 laser welding is “nail-head” shape. Those result from special heating mode of laser deep penetration welding. The tension strength of CO_2 laser and YAG laser joints equal to that of the base metal, but the former has better ductility. All welds consist mainly of the acicular α phase and a few β phase in microstructure. The dendritic crystal of CO_2 laser weld is a little finer than YAG laser weld. According the research CO_2 laser is better than YAG laser for welding of BT20 titanium alloy.

Gas Pool Coupled Activating TIG Welding Method with Coupling Arc Electrode

Gas pool coupled activating TIG(GPCA?TIG) welding put forward in?house can dramatically enhance weld penetration of TIG welding through introducing active element oxygen to reverse the Marangoni convection flow in the molten pool. In order to further improve the welding productivity, the normal solid tungsten electrode is replaced by a kind of coupling arc electrode. The changes of arc pressure distribution along anode surface and the weld appearance were evaluated. On this basis, the dependences of weld shape characterized with weld depth, width and undercut on the main welding parameters were discussed. The results indicate, the substitution of coupling arc electrode can lead to an obvious decrease of arc pressure. Compared to hollow tungsten electrode and twin tungsten electrodes, the coupling arc electrode is much easier to manufacture and has more compacter structure. Combined with the symmetric distribution of arc pressure in di erent directions, this electrode has extensive adaptability. In the GPCA?TIG welding with coupling arc electrode, both the substitution of coupling arc electrode and the introduction of outer active gas oxygen can reduce the possibilities of producing humping bead and undercut. Their joint action makes this welding method have the capability of realizing high travel speed and deep penetration welding.

Weld shape and microstructure of TC4 laser welding with activating flux of Na_(2)SiF_(6)

Na_(2)SiF_(6) was used as surface activating flux for laser welding of TC4 titanium alloy. The effect of Na_(2)SiF_(6) on TC4 titanium alloy laser welding was determined by observing the weld surface. The morphological characteristics of the high temperature plasma above the workpiece was observed and analyzed by using high-speed digital camera system. The variation of weld depth,width and microstructure were analyzed by optical microscope. The experimental results show that laser weld of TC4 titanium alloy has good appearance with activating flux of Na_(2)SiF_(6), weld penetration increases by about 0.8%–12%, while weld surface width decrease by about 10%–29%, the depth to width ratio is effectively improved. The inhomogeneity of weld microstructure was improved, and the crystallization direction of β columnar crystals on the upper part of the weld was changed, the grain size and microstructure of the weld were refined by Na_(2)SiF_(6).

Effect of Welding Parameters on GTA Weld Shape for Pure Iron Plate under Ar-O_2 Mixed Shielding

Weld shape variation for different welding parameters is investigated on pure iron plate under gas tungsten arc （GTA） welding with argon-oxygen mixed shielding. Results showed that small addition of oxygen to the argon base shielding gas can effectively adjust the oxygen adsorption to the molten pool. An inward Marangoni convection occurs on the pool surface when the oxygen content in the weld pool is over the critical value, 80×10^-6, for pure iron plate under Ar-0.3%O2 mixed shielding. Low oxygen content in the weld pool changes the inward Marangoni to an outward direction under the Ar-0.1%O2 shielding. The GTA weld shape depends to a large extent on the pattern and strength of the Marangoni convection on the pool surface, which is determined by the content of surface active element, oxygen, in the weld pool and the welding parameters. The strength of the Marangoni convection on the liquid pool is a product of the temperature coefficient of the surface tension （dσ/dT） and the temperature gradient （dT/dr） on the pool surface. Different welding parameters will change the temperature distribution and gradient on the pool surface, and therefore, affect the strength of Marangoni convection and the weld shape.

Neural network modeling for weld shape process of P-GMAW

Weld shape control is a fundamental issue in automatic welding. In this paper, a double side visual system is established for pulsed gas metal arc welding （ P-GMAW） , and both topside and backside weld pool images can be captured and stored continuously in real time. By analyzing the weld shape regulation with the molten metal volume, some topside weld pool characterized parameters （WPCPs） are proposed for determining penetration in butt welding of thin mild steel. Moreover, some BP network models are established to predict backside Weld pool width with welding parameters and WPCPs as inputs.

Study on welding power source used in intelligent control system for weld pool shape in pulsed GTAW

This paper analyses the performance request of arc welding power source used in intelligent control of weld pool shape in pulsed GTAW, and develops a sample power source. The main circuit of the power source takes the structure of single ended inverter with two switches, and takes IGBTs as power switches. The working frequency of the inverter is set at 20 kHz. The control circuit takes PWM circuit as center, and uses single chip computer to complete the manage functions such as the control of working sequence, setting and changing of the welding parameters, sensing of the welding states and communication with outside computer etc. The dynamic reacting time of the whole power is 1 ms, the range of the output current is 5～250 A, the precision of the output current reaches to 1 A. The power strikes arc by contacting workpiece under 5 A, and have convenient interface with system computer. All above shows this power source is one with high performance.

Numerical simulation for pulsed laser-gas tungsten arc hybrid welding of magnesium alloy

Based on the extended application of COMSOL multiphysics, a novel dual heat source model for pulsed laser-gas tungsten arc （GTA） hybrid welding was established. This model successfully solved the problem of simulation inaccuracy caused by energy superposition effect between laser and arc due to their different physical characteristics. Numerical simulation for pulsed laser-GTA hybrid welding of magnesium alloy process was conducted, and the simulation indicated good agree- ments with the measured thermal cycle curve and the shape of weld beads. Effects of pulse laser parameters （laser-excited current, pulse duration, and pulse frequency） on the temperature field and weld pool morphology were investigated. The experimental and simulation results suggest that when the laser pulse energy keeps constant, welding efficiency of the hybrid heat source is increased by increasing laser current or decreasing pulse duration due to the increased ratio of the weld bead depth to width. With large laser currents, severe spatters tend to occur. For optimized welding process, the laser current should be controlled in the range of 150-175 A, the pulse duration should be longer than 1 ms, and the pulse frequency should be equal to or slightly greater than 20 Hz.

Weld Shape Variation and Electrode Oxidation Behavior under Ar-(Ar-CO_2) Double Shielded GTA Welding

Double shielded gas tungsten arc welding （GTAW, also known as tungsten inert gas （TIG） welding） of an SUS304 stainless steel with pure inert argon as the inner layer shielding and the At-CO2 or CO2 active gas as the out layer shielding was proposed in this study to investigate its effect on the tungsten electrode protection and the weld shape variation. The experimental results showed that the inner inert argon gas can successfully prevent the outer layer active gas from contacting and oxidizing the tungsten electrode during the welding process. Active gas, carbon dioxide, in the outer layer shielding is decomposed in the arc and dissolves in the liquid pool, which effectively adjusts the active element, oxygen, content in the weld metal. When the weld metal oxygen content is over 70×10-6, the surface-tension induced Marangoni convection changes from outward into inward, and the weld shape varies from a wide shallow one to a narrow deep one. The effect of the inner layer gas flow rate on the weld bead morphology and the weld shape was investigated systematically. The results show that when the flow rate of the inner argon shielding gas is too low, the weld bead is easily oxidized and the weld shape is wide and shallow. A heavy continuous oxide layer on the liquid pool is a barrier to the liquid pool movement.

Research on modeling of heat source for electron beam welding fusion-solidification zone

In this paper, the common heat source model of point and linear heat source in the numerical simulation of electron beam welding （EBW） were summarized and introduced. The combined point-linear heat source model was brought forward and to simulate the welding temperature fields of EBW and predicting the weld shape. The model parameters were put forward and regulated in the combined model, which included the ratio of point heat source to linear heat source Qpr and the distribution of linear heat source Lr. Based on the combined model, the welding temperature fields of EBW were investigated. The results show that the predicted weld shapes are conformable to those of the actual, the temperature fields are reasonable and correct by simulating with combined point-linear heat source model and the typical weld shapes are gained.