In this study,the perovskite nanocomposite PrFe_(x)Co_(1-x)O_(3)(Pr(S))was successfully synthesized by the sol-gel method;PrFe_(x)Co_(1-x)O_(3)/Al-pillared montmorillonite(Pr(S)/Mt)catalysts were prepared by impregnat...In this study,the perovskite nanocomposite PrFe_(x)Co_(1-x)O_(3)(Pr(S))was successfully synthesized by the sol-gel method;PrFe_(x)Co_(1-x)O_(3)/Al-pillared montmorillonite(Pr(S)/Mt)catalysts were prepared by impregnation(D)method and solid-melting(G)method,respectively,with Pr(S)as the active component and Al-pillared montmorillonite as the carrier.The catalysts were applied to treat the 2-hydroxybenzoic acid(2-HA)-simulated wastewater by catalytic wet peroxide oxidation(CWPO)technique,and the chemical oxygen demand(COD)removal rate and the 2-HA degradation rate were used as indicators to evaluate the catalytic performance.The results of the experiment indicated that the solid-melting method was more conducive to preparing the catalyst when the Co/Fe molar ratio of 7:3 and the optimal structural properties of the catalysts were achieved.The influence of operating parameters,including reaction temperature,catalyst dosage,H_(2)O_(2)dosage,pH,and initial 2-HA concentration,were optimized for the degradation of 2-HA by CWPO.The results showed that 97.64%of 2-HA degradation and 75.23%of COD removal rate were achieved under more suitable experimental conditions.In addition,after the catalyst was used five times,the degradation rate of 2-HA could still reach 76.93%,which implied the high stability and reusability of the catalyst.The high catalytic activity of the catalyst was due to the doping of Co into PrFeO_(3),which could promote the generation of HO·,and the high stability could be attributed to the loading of Pr(S)onto Al-Mt,which reduced the leaching of reactive metals.The study of reaction mechanism and kinetics showed that the whole degradation process conformed to the pseudo-firstorder kinetic equation,and the Langmuir-Hinshelwood method was applied to demonstrate that catalysis was dominant in the degradation process.展开更多
Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing...Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing free radicals, the stability of catalysts is often insufficient, which has become a bottleneck in the application of CWAO. In this paper, a copper-based catalyst with excellent hydrothermal stability was designed and prepared. TiO_(2) with excellent stability was used as the carrier to ensure the longterm anchoring of copper and reduce the leaching of the catalyst. The one pot sol–gel method was used to ensure the super dispersion and uniform distribution of copper nanoparticles on the carrier, so as to ensure that more active centers could be retained in a longer period. Experiments show that the catalyst prepared by this method has good stability and catalytic activity, and the catalytic effect is not significantly reduced after 10 cycles of use. The oxidation degradation experiment of m-cresol with the strongest biological toxicity and the most difficult to degrade in coal chemical wastewater was carried out with this catalyst. The results showed that under the conditions of 140℃, 2 MPa and 2 h, m-cresol with a concentration of up to 1000 mg·L^(-1) could be completely degraded, and the COD removal rate could reach 79.15%. The biological toxicity of wastewater was significantly reduced. The development of the catalyst system has greatly improved the feasibility of CWAO in the treatment of refractory wastewater such as coal chemical wastewater.展开更多
There have been many studies on life cycle assessment in sewage treatment,but there are scarce few studies on the treatment of industrial wastewater in combination with advanced oxidation technology,especially in cata...There have been many studies on life cycle assessment in sewage treatment,but there are scarce few studies on the treatment of industrial wastewater in combination with advanced oxidation technology,especially in catalytic wet air oxidation(CWAO).There are no cases of using actual industrialized data onto life cycle assessment.This paper uses Simapro 9.0 software to establish a life cycle assessment model for the treatment of high-concentration organic wastewater by CWAO,and comprehensively explains the impact on the environment from three aspects:the construction phase,the operation phase and the demolition phase.In addition,sensitivity analysis and uncertainty analysis were performed.The results showed that the key factors affecting the environment were marine ecotoxicity,mineral resource consumption and global warming,the operation stage had the greatest impact on the environment,which was related to high power consumption during operation and emissions from the treatment process.Sensitivity analysis showed that electricity consumption has the greatest impact on abiotic depletion and freshwater aquatic ecotoxicity,and it also proved that global warming is mainly caused by pollutant emissions during operation phase.Monte Carlo simulations found slightly higher uncertainty for abiotic depletion and toxicity-related impact categories.展开更多
The catalytic wet air oxidation of aniline over Ru catalysts supported on modified Ti 2 (Ti 2, Ti0.9Ce0.1O2, Ti0.9Zr0.1O2) is investigated. A series of characterization techniques are conducted to deter...The catalytic wet air oxidation of aniline over Ru catalysts supported on modified Ti 2 (Ti 2, Ti0.9Ce0.1O2, Ti0.9Zr0.1O2) is investigated. A series of characterization techniques are conducted to determine the relationship between the physico-chemical properties and the catalytic performance. As a result of the good metal dispersion and large number of surface oxygen species, the Ru/Ti0.9 Zr0.1O2 catalyst presents the best catalytic activity among the tested samples. The effects of the operating conditions on the reaction are investigated and the optimal reaction conditions are determined. Based on the relationship between the by-products concentration and the reaction time, the reaction path for the catalytic oxidation of aniline is established. Carbonaceous deposits on the surface of the support are known to be the main reason for catalyst deactivation. The catalysts maintain a constant activity even after three consecutive cycles.展开更多
A copper-based non-aqueous-phase desulfurization agent is prepared by adding CuCl_(2) to the solvent N,Ndimethylformamide(DMF).Static desulfurization experiments show that the agent has high efficiency.However,the des...A copper-based non-aqueous-phase desulfurization agent is prepared by adding CuCl_(2) to the solvent N,Ndimethylformamide(DMF).Static desulfurization experiments show that the agent has high efficiency.However,the desulfurization reaction leads to the formation of a copper sulfide precipitate.It is found that the addition of chloride ions in the form of hydrochloric acid or potassium chloride prevents the formation of copper sulfide,and elemental sulfur is precipitated instead.The efficient absorption of H2S by the Cu/HCl–DMF agent relies on the rapid coordination of Cu^(2+)with DMF,Cl^(−),and H2S molecules to form a[Cu(DMF)_(n−p)(HS−)_(p)(Cl−)_(m)]_((2−p−m))+complex.The desulfurization agent has a sulfur capacity of up to 9.81 g/L when used in static bubble desulfurization at atmospheric pressure.The system has low viscosity and good chemical and thermal stability.It can be rapidly regenerated through continuous oxidation.After five repetitions of the regeneration procedure,the sulfur capacity reaches more than 91%of the initial capacity,indicating the potential of the system for commercial applications.展开更多
A novel process, microwave assisted catalytic wet air oxidation(MW-CWO), was applied for the degradation of H-acid(1-amino-8-naphthol-3, 6-disulfonic acid) in aqueous solution. Ni-loaded granular activated carbon(GAC)...A novel process, microwave assisted catalytic wet air oxidation(MW-CWO), was applied for the degradation of H-acid(1-amino-8-naphthol-3, 6-disulfonic acid) in aqueous solution. Ni-loaded granular activated carbon(GAC), prepared by immersion-calcination method, was used as catalyst. The results showed that the MW-CWO process was very effective for the degradation of H-acid in aqueous solution under atmospheric pressure with 87.4% TOC (total organic carbon) reduction in 20 min. Ni on GAC existed in the form of NiO as specified by XRD. Loss of Ni was significant in the initial stage, and then remained almost constant after 20 min reaction. BET surface area results showed that the surface property of GAC after MW-CWO process was superior to that of blank GAC.展开更多
A wet catalytic oxidation at room temperature was investigated with solution containing ferric, ferrous and cupric ions for H2S removal. The experiments were carried out in a two step process, and the results obtained...A wet catalytic oxidation at room temperature was investigated with solution containing ferric, ferrous and cupric ions for H2S removal. The experiments were carried out in a two step process, and the results obtained show that the removal efficiency of H2S can always reach 100% in a 300 mm scrubbing column with four sieve plates, and the regeneration of ferric ions in 200 mm bubble column can match the consumed ferric species in absorption. Removal of H2S, production of elemental sulfur and regeneration of ferric, cupric ions can all be accomplished at the same time. No raw material is consumed except O2 in flue gas or air, the process has no secondary pollution and no problem of catalyst degradation and congestion.展开更多
The wet oxidation of AlGaAs with high Al content in a distributed Bragg reflectors (DBR) is studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Some voids distribute along t...The wet oxidation of AlGaAs with high Al content in a distributed Bragg reflectors (DBR) is studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Some voids distribute along the oxide/GaAs interfaces due to the stress induced by the wet oxidation of the AlGaAs layers. These voids decrease the shrinkage of the Al2O3 layers to 8% instead of the theoretical 20% when compared to the unoxidized AlGaAs layers. With the extension of oxidation time, the reactants are more completely transported to the front interface and the products are more completely transported out along the porous interfaces. As a result,the oxide quality is better.展开更多
Catalytic wet air oxidation(CWAO) was employed to reduce the organic compounds in landfill leachate and the effects of temperature, oxygen pressure, catalyst dosage, and concentration of the organic compounds on the T...Catalytic wet air oxidation(CWAO) was employed to reduce the organic compounds in landfill leachate and the effects of temperature, oxygen pressure, catalyst dosage, and concentration of the organic compounds on the TOC and COD Cr removal rates were studied. The degradation kinetics of landfill leachate was also investigated and an exponential experiential model consisting of four influential factors was established to describe the reduction of the organic compounds in the landfill leachate. Meanwhile, the GC-MS technique was used to detect the components of the organic intermediates for the inference of the decomposition mechanisms of the organic compounds in landfill leachate. The results reveal that the reaction temperature and the catalyst dosage are the most important factors affecting the degradation reaction of the organic compounds and that the principal intermediates confirmed by GC-MS are organic acids at a percentage of more than 88% with no aldehydes or alcohols detected. The decomposition mechanisms of the organic compounds in landfill leachate were inferred based on the GC-MS information as follows: the activated gas phase O 2 captured the hydrogen of the organic pollutants to produce free radicals, which then initiated the catalytic reaction. So most of the organic compounds were oxidized into CO 2 and H 2O ultimately. In general, catalytic wet air oxidation over catalyst Co 3O 4/Bi 2O 3 was a very promising technique for the treatment of landfill leachate.展开更多
A kind of CWAO catalyst, RuO_2/γ-Al_2O_3, was prepared by dipping Al_2O_3into the aqueous solution of RuCl_3·3H_2O. XRD, SEM and TEM were used to determine the catalyticstructure. Influences of the calcination t...A kind of CWAO catalyst, RuO_2/γ-Al_2O_3, was prepared by dipping Al_2O_3into the aqueous solution of RuCl_3·3H_2O. XRD, SEM and TEM were used to determine the catalyticstructure. Influences of the calcination temperature, the initial pH of the feed solution anddegradation temperature on the activity of the RuO_2/γ-Al_2O_3 catalyst were investigated and thereaction mechanism was preliminarily studied. Results showed that uniform dispersion of RuO_2crystallites was observed on the surface of the catalyst. The activity of the catalyst was higher atcalcination temperature of 300℃ for 3 h and the particle reunion occurred and some large RuO_2crystallites were abundant at high calcination temperature of 500℃ The activity of the catalyst wasbetter in the acid solution than in the alkaline solution. Increasing degradation temperature andusing the catalyst could shorten the induction periods so that the phenol and COD removal wereincreased. For RuO_2/γ-Al_2O_3 catalyst, the phenol and COD removal were respectively 98% and 80%in a temperature of 150℃, pH of 5.6 and pressure of 3 MPa after a 2 h reaction. This indicated thatRu/γ-Al_2O_3 catalyst had good activity.展开更多
Polyvinyl alcohol (PVA)-containing desizing wastewater was treated by various wet oxidation methods.Parameters such as reaction temperature, initial solution pH, and the dosage of H2O2 were investigated in terms of ch...Polyvinyl alcohol (PVA)-containing desizing wastewater was treated by various wet oxidation methods.Parameters such as reaction temperature, initial solution pH, and the dosage of H2O2 were investigated in terms of chemical oxygen demand (CODcr) and total organic carbon (TOC) removal rate. Up to 90% of the initial CODcr was removed by wet air oxidation(WAO) at 270℃ with stoichiometric oxygen supply, while at temperature of 200℃, the CODcr removal rate was found to be 80%. Similar results were obtained by Promoted WAO (PWAO) and wet peroxide oxidation(WPO) at a lower temperature of 150℃. Reaction temperature was found to have a significant effect on the oxidation performance for all the methods. Initial solution pH was observed to play a significant role in PWAO and WPO where H2O2 was employed. Comparison of WAO, CWAO(catalytic wet air oxidation), PWAO and WPO shows that the rate of CODcr removal increases in the order: WAO, CWAO, PWAO and WPO.展开更多
The removal of hydrogen sulfide from gas plays an important role in rational utilization of resources and environ- mental protection. In this paper, the process of hydrogen sulfide removal by wet oxidation method in a...The removal of hydrogen sulfide from gas plays an important role in rational utilization of resources and environ- mental protection. In this paper, the process of hydrogen sulfide removal by wet oxidation method in a rotating packed bed was investigated in a scale for treating 10 000 Nm3/h of gas. On the basis of studying the influence of the species and con- centration of alkali source, the liquid/gas volume ratio, the high gravity factor, and the hydrogen sulfide content in feed gas on the desulfurization effect, the suitable technological conditions were obtained. The hydrogen sulfide removal efficiency could reach 98.0% under these conditions. The results of continuous operation of process facilities showed that the high gravity method has many merits including higher desulfurization rate, good stability in operation, lower liquid/gas volume ratio, greater operation elasticity, and apparent energy saving effects.展开更多
Catalytic wet air oxidation (CWAO) of o-chlorophenol in wastewater was studied in a stainless steel autoclave using four different Fe catalysts in the temperature range of 100?200 °C. Experimental results showed ...Catalytic wet air oxidation (CWAO) of o-chlorophenol in wastewater was studied in a stainless steel autoclave using four different Fe catalysts in the temperature range of 100?200 °C. Experimental results showed that high rate of o-chlorophenol and CODCr (Chemical Oxygen Demand, mg/L) removal by CWAO was obtained at relatively low temperature and pressure. The catalysts Fe2(SO4)3, FeSO4, Fe2O3 and FeCl3 all exhibited high catalytic activity. More than 93.7% of the initial CODCr and nearly 100% of o-chlorophenol were removed at 150 °C after 150 min with FeSO4 as catalyst. The CWAO of o-chlorophenol was found to be pseudo-first order reaction with respect to o-chlorophenol, with activation energy of 75.56 kJ/mol in the temperature range of 100-175 °C.展开更多
A Cu–Fe–La/γ-Al_2O_3(CFLA) catalyst was prepared by the excessive impregnation method and characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron ...A Cu–Fe–La/γ-Al_2O_3(CFLA) catalyst was prepared by the excessive impregnation method and characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The results indicate that the catalyst contained mostly Cu^(2+), Fe^(3+), and La^(3+)and a small amount of Cu^+, Fe^(2+), and La. The active components were uniformly distributed in the catalyst, and the particle size of the components was approximately 7.5 nm. The CFLA catalyst was used for the treatment of methyl orange(MO) solution by catalytic wet air oxidation(CWAO), and it exhibited a high catalytic activity. The catalytic reaction involved variable valence states of metals and free-radical reaction mechanism. The CWAO reaction of MO solution was fitted by a segmented first-order dynamic model, and the rapid reaction apparent activation energy was 13.9 k J·mol^(-1).展开更多
Four metal oxide catalysts composed of copper(Cu), stannum(Sn), copper-stannum(Cu-Sn) and copper-cerium(Cu-Ce) respectively were prepared by the co-impregnation method, and γ-alumina(γ-Al 2O 3) is selected as supp...Four metal oxide catalysts composed of copper(Cu), stannum(Sn), copper-stannum(Cu-Sn) and copper-cerium(Cu-Ce) respectively were prepared by the co-impregnation method, and γ-alumina(γ-Al 2O 3) is selected as support. A first-order kinetics model was established to study the catalytic wet air oxidation of phenol at different temperature when these catalysts were used. The model simulations are good agreement with present experimental data. Results showed that the reaction rate constants can be significantly increased when catalysts were used, and the catalyst of 6% Cu—10%Ce/γ-Al 2O 3 showed the best catalytic activity. This is consistent with the result of catalytic wet air oxidation of phenol and the COD removal can be arrived at 98.2% at temperature 210℃, oxygen partial pressure 3 MPa and reaction time 30 min. The activation energies of each reaction with different catalysts are nearly equal, which is found to be about 42 kJ/mol and the reaction in this study is proved to be kinetics control.展开更多
Catalytic wet air oxidation (CWAO) was investigated in laboratory-scale experiments for the treatment of o-chlorophenol in wastewater. Experimental results showed that wet air oxidation (WAO) process in the absence of...Catalytic wet air oxidation (CWAO) was investigated in laboratory-scale experiments for the treatment of o-chlorophenol in wastewater. Experimental results showed that wet air oxidation (WAO) process in the absence of catalyst was also effective for o-chlorophenol in wastewater treatment. Up to 80% of the initial CODCr was removed by wet air oxidation at 270℃ with twice amount of the required stoichiometric oxygen supply. At temperature of 150℃, the removal rate of CODCr was only 30%. Fe2(SO4)3, CuSO4, Cu(NO3)2 and MnSO4 exhibited high catalytic activity. Higher removal rate of CODCr was obtained by CWAO. More than 96% of the initial CODCr was removed at 270℃ and 84.6%-93.6% of the initial CODCr was removed at 150℃. Mixed catalysts had better catalytic activity for the degradation of o-chlorophenol in wastewater.展开更多
A narrowed Si_(0.7)Ge_(0.3)channel fin field-effect transistor(FinFET)device is demonstrated in detail by using an accuratecyclic wet treatment process.The Si_(0.7)Ge_(0.3)fin/per side of 0.63 nm in thickness can be a...A narrowed Si_(0.7)Ge_(0.3)channel fin field-effect transistor(FinFET)device is demonstrated in detail by using an accuratecyclic wet treatment process.The Si_(0.7)Ge_(0.3)fin/per side of 0.63 nm in thickness can be accurately removed in each cycleby utilizing a self-limited oxidation with 40%HNO_(3)solution in 40 s and oxidation removal can be achieved with 1%HFsolution in 10 s.As a result,after the dummy gate removal,the fin width of Si_(0.7)Ge_(0.3)can be narrowed from 20 nm to 8 nmby utilizing 10 cycles of this wet treatment process.Compared with the conventional Si_(0.7)Ge_(0.3)FinFET under a similarprocess,the narrowed Si_(0.7)Ge_(0.3)channel FinFET can realize a strong gate control capability by using this newly developedwet treatment process,because its subthreshold slope can be reduced by 24%,improving from 87 mV/dec to 64 mV/dec.展开更多
Two series of cobalt(Ⅲ)\|containing spinel catalysts were prepared by the decomposition of the corresponding nitrates. The catalysts doped with bismuth oxide exhibit a higher activity in the wet air oxidation of acet...Two series of cobalt(Ⅲ)\|containing spinel catalysts were prepared by the decomposition of the corresponding nitrates. The catalysts doped with bismuth oxide exhibit a higher activity in the wet air oxidation of acetic acid than those without dopant bismuth oxide. The catalysts were investigated by XRD,TEM,ESR,UV\|DRS and XPS,and the interaction between Co and Bi was studied as well. It has been found that nano\|sized bismuth oxide is paved on the surface of cobalt spinel crystal and the structures of cobalt(Ⅲ)\|containing spinel are still maintained. The shift of the binding energy of Bi\-\{\%4f\%\-\{7/2\}\} is related to the catalytic activity of these catalysts doped with bismuth oxide.展开更多
The pretreatment technology of wet air oxidation(WAO) and coagulation and acidic hydrolysis for apramycin wastewater was investigated in this paper. The COD, apramycin, NH^+_4 concentration, and the ratio of BOD_5/COD...The pretreatment technology of wet air oxidation(WAO) and coagulation and acidic hydrolysis for apramycin wastewater was investigated in this paper. The COD, apramycin, NH^+_4 concentration, and the ratio of BOD_5/COD were analyzed, and the color and odor of the effluent were observed. WAO of apramycin wastewater, without catalyst and with RuO_2/Al_2O_3 and RuO_2-CeO_2/Al_2O_3 catalysts, was carried out at degradation temperature of 200℃ and the total pressure of 4 MPa in a 1 L batch reactor. The result showed that the apramycin removals were respectively 50 2% and 55 0%, COD removals were 40 0% and 46 0%, and the ratio of BOD_5/COD was increased to 0 49 and 0 54 with RuO_2/Al_2O_3 and RuO_2-CeO_2/Al_2O_3 catalysts in catylytic wet air oxidation(CWAO) after the reaction of 150 min. With the pretreatment of coagulation and acidic hydrolysis, COD and apramycin removals were slight decreased, and the ratio of BOD_5/COD was increased to 0 45, and the effluents was not suitable to biological treatment. The color and odor of the wastewater were effectively controlled and the reaction time was obviously shortened with WAO. HO_2· may promote organic compounds oxidized in WAO of the apramycin wastewater. The addition of CeO_2 could promote the activity and stability of RuO_2/Al_2O_3 in WAO of apramycin wastewater.展开更多
In this paper, we described the optimization of the wet oxidation pretreatment conditions to enhance enzymatic hydrolysis efficiency, using poplar waste from the stock section of a paper mill as the raw material. We s...In this paper, we described the optimization of the wet oxidation pretreatment conditions to enhance enzymatic hydrolysis efficiency, using poplar waste from the stock section of a paper mill as the raw material. We showed that the optimal conditions of the pretreatment for poplar waste were an initial p H value of 10, a temperature of 195℃, a holding time of 15 min, and an oxygen pressure of 1.2 MPa. In this case, the yield of the obtained solid material produced by the process was 51.7% and the reducing sugar yield was 46.8%. The solid part obtained from the pretreatment process was hydrolyzed by cellulase L-10. The optimal enzymatic conditions were a temperature of 49℃, a duration time of 56 h, an enzyme dosage of 38 FPU/g at a p H value of 4.8, and a solid-to-liquor ratio of 1∶50. The resulting cellulose conversion rate reached 96.4% in terms of the pretreated substances. In addition, a chemical composition analysis of the poplar waste and pretreated material indicated that about 92% of the hemicelluloses and 43% of the lignin in the raw material were degraded and dissolved. In addition, the crystallization decreased from 57.5% to 54.8%. An obvious fibrillation of the fiber pretreated by the wet oxidization process was observed by SEM. Moreover, high-performance liquid chromatography(HPLC) results showed a high xylose content and monosaccharide degradation products in the pretreatment solution. In conclusion, the wet oxidation pretreatment process could efficiently degrade or remove the lignin and hemicellulose, as well as reduce the crystallinity of the lignocellulosic material, which resulted in animprovement of the enzymatic ability and an increase in the cellulose conversion rate.展开更多
基金supported by the Key Research and Development Program of Shaanxi,China(2018GY-067).
文摘In this study,the perovskite nanocomposite PrFe_(x)Co_(1-x)O_(3)(Pr(S))was successfully synthesized by the sol-gel method;PrFe_(x)Co_(1-x)O_(3)/Al-pillared montmorillonite(Pr(S)/Mt)catalysts were prepared by impregnation(D)method and solid-melting(G)method,respectively,with Pr(S)as the active component and Al-pillared montmorillonite as the carrier.The catalysts were applied to treat the 2-hydroxybenzoic acid(2-HA)-simulated wastewater by catalytic wet peroxide oxidation(CWPO)technique,and the chemical oxygen demand(COD)removal rate and the 2-HA degradation rate were used as indicators to evaluate the catalytic performance.The results of the experiment indicated that the solid-melting method was more conducive to preparing the catalyst when the Co/Fe molar ratio of 7:3 and the optimal structural properties of the catalysts were achieved.The influence of operating parameters,including reaction temperature,catalyst dosage,H_(2)O_(2)dosage,pH,and initial 2-HA concentration,were optimized for the degradation of 2-HA by CWPO.The results showed that 97.64%of 2-HA degradation and 75.23%of COD removal rate were achieved under more suitable experimental conditions.In addition,after the catalyst was used five times,the degradation rate of 2-HA could still reach 76.93%,which implied the high stability and reusability of the catalyst.The high catalytic activity of the catalyst was due to the doping of Co into PrFeO_(3),which could promote the generation of HO·,and the high stability could be attributed to the loading of Pr(S)onto Al-Mt,which reduced the leaching of reactive metals.The study of reaction mechanism and kinetics showed that the whole degradation process conformed to the pseudo-firstorder kinetic equation,and the Langmuir-Hinshelwood method was applied to demonstrate that catalysis was dominant in the degradation process.
基金support provided by the National Natural Science Foundation of China (21978143 and 21878164)。
文摘Catalytic wet air oxidation(CWAO) can degrade some refractory pollutants at a low cost to improve the biodegradability of wastewater. However, in the presence of high temperature and high pressure and strong oxidizing free radicals, the stability of catalysts is often insufficient, which has become a bottleneck in the application of CWAO. In this paper, a copper-based catalyst with excellent hydrothermal stability was designed and prepared. TiO_(2) with excellent stability was used as the carrier to ensure the longterm anchoring of copper and reduce the leaching of the catalyst. The one pot sol–gel method was used to ensure the super dispersion and uniform distribution of copper nanoparticles on the carrier, so as to ensure that more active centers could be retained in a longer period. Experiments show that the catalyst prepared by this method has good stability and catalytic activity, and the catalytic effect is not significantly reduced after 10 cycles of use. The oxidation degradation experiment of m-cresol with the strongest biological toxicity and the most difficult to degrade in coal chemical wastewater was carried out with this catalyst. The results showed that under the conditions of 140℃, 2 MPa and 2 h, m-cresol with a concentration of up to 1000 mg·L^(-1) could be completely degraded, and the COD removal rate could reach 79.15%. The biological toxicity of wastewater was significantly reduced. The development of the catalyst system has greatly improved the feasibility of CWAO in the treatment of refractory wastewater such as coal chemical wastewater.
基金supported by National Natural Science Foundation of China(52100072,52100213)the Fundamental Research FundsfortheCentralUniversities(JZ2021HGTA0159,JZ2021HGQA0212)+2 种基金the Strategic Priority Research Program of the Chinese Academy of Sciences(XDA21021101)the Scientific Research Common Program of Beijing Municipal Commission of Education(KM202010017006)the Beijing Natural Science Foundation(8214056)。
文摘There have been many studies on life cycle assessment in sewage treatment,but there are scarce few studies on the treatment of industrial wastewater in combination with advanced oxidation technology,especially in catalytic wet air oxidation(CWAO).There are no cases of using actual industrialized data onto life cycle assessment.This paper uses Simapro 9.0 software to establish a life cycle assessment model for the treatment of high-concentration organic wastewater by CWAO,and comprehensively explains the impact on the environment from three aspects:the construction phase,the operation phase and the demolition phase.In addition,sensitivity analysis and uncertainty analysis were performed.The results showed that the key factors affecting the environment were marine ecotoxicity,mineral resource consumption and global warming,the operation stage had the greatest impact on the environment,which was related to high power consumption during operation and emissions from the treatment process.Sensitivity analysis showed that electricity consumption has the greatest impact on abiotic depletion and freshwater aquatic ecotoxicity,and it also proved that global warming is mainly caused by pollutant emissions during operation phase.Monte Carlo simulations found slightly higher uncertainty for abiotic depletion and toxicity-related impact categories.
基金supported by the National Natural Science Foundation of China(21333003,21577034)National Basic Research Program of China(2013CB933200)+1 种基金National High Technology Research and Development Program of China(2015AA034603)the Fundamental Research Funds for the Central Universities(WJ1514020)~~
文摘The catalytic wet air oxidation of aniline over Ru catalysts supported on modified Ti 2 (Ti 2, Ti0.9Ce0.1O2, Ti0.9Zr0.1O2) is investigated. A series of characterization techniques are conducted to determine the relationship between the physico-chemical properties and the catalytic performance. As a result of the good metal dispersion and large number of surface oxygen species, the Ru/Ti0.9 Zr0.1O2 catalyst presents the best catalytic activity among the tested samples. The effects of the operating conditions on the reaction are investigated and the optimal reaction conditions are determined. Based on the relationship between the by-products concentration and the reaction time, the reaction path for the catalytic oxidation of aniline is established. Carbonaceous deposits on the surface of the support are known to be the main reason for catalyst deactivation. The catalysts maintain a constant activity even after three consecutive cycles.
基金the China National Science and Technology Major Project(2016ZX05017)the Sinopec Group Corporation 2020 Science and Technology Project“Organic Sulfur Catalytic Hydrolysis Technology Improves Quality Research”(No.120049-1).
文摘A copper-based non-aqueous-phase desulfurization agent is prepared by adding CuCl_(2) to the solvent N,Ndimethylformamide(DMF).Static desulfurization experiments show that the agent has high efficiency.However,the desulfurization reaction leads to the formation of a copper sulfide precipitate.It is found that the addition of chloride ions in the form of hydrochloric acid or potassium chloride prevents the formation of copper sulfide,and elemental sulfur is precipitated instead.The efficient absorption of H2S by the Cu/HCl–DMF agent relies on the rapid coordination of Cu^(2+)with DMF,Cl^(−),and H2S molecules to form a[Cu(DMF)_(n−p)(HS−)_(p)(Cl−)_(m)]_((2−p−m))+complex.The desulfurization agent has a sulfur capacity of up to 9.81 g/L when used in static bubble desulfurization at atmospheric pressure.The system has low viscosity and good chemical and thermal stability.It can be rapidly regenerated through continuous oxidation.After five repetitions of the regeneration procedure,the sulfur capacity reaches more than 91%of the initial capacity,indicating the potential of the system for commercial applications.
基金The Hi Tech Research and Development Program(863) of China(No. 2002AA649090) and the National Basic Research Program(973) of China(No.2003CB415006)
文摘A novel process, microwave assisted catalytic wet air oxidation(MW-CWO), was applied for the degradation of H-acid(1-amino-8-naphthol-3, 6-disulfonic acid) in aqueous solution. Ni-loaded granular activated carbon(GAC), prepared by immersion-calcination method, was used as catalyst. The results showed that the MW-CWO process was very effective for the degradation of H-acid in aqueous solution under atmospheric pressure with 87.4% TOC (total organic carbon) reduction in 20 min. Ni on GAC existed in the form of NiO as specified by XRD. Loss of Ni was significant in the initial stage, and then remained almost constant after 20 min reaction. BET surface area results showed that the surface property of GAC after MW-CWO process was superior to that of blank GAC.
文摘A wet catalytic oxidation at room temperature was investigated with solution containing ferric, ferrous and cupric ions for H2S removal. The experiments were carried out in a two step process, and the results obtained show that the removal efficiency of H2S can always reach 100% in a 300 mm scrubbing column with four sieve plates, and the regeneration of ferric ions in 200 mm bubble column can match the consumed ferric species in absorption. Removal of H2S, production of elemental sulfur and regeneration of ferric, cupric ions can all be accomplished at the same time. No raw material is consumed except O2 in flue gas or air, the process has no secondary pollution and no problem of catalyst degradation and congestion.
文摘The wet oxidation of AlGaAs with high Al content in a distributed Bragg reflectors (DBR) is studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Some voids distribute along the oxide/GaAs interfaces due to the stress induced by the wet oxidation of the AlGaAs layers. These voids decrease the shrinkage of the Al2O3 layers to 8% instead of the theoretical 20% when compared to the unoxidized AlGaAs layers. With the extension of oxidation time, the reactants are more completely transported to the front interface and the products are more completely transported out along the porous interfaces. As a result,the oxide quality is better.
基金Program Foundation for Environmental Protection of 2 0 0 2 by Jilin Province Environm ental ProtectionBureau
文摘Catalytic wet air oxidation(CWAO) was employed to reduce the organic compounds in landfill leachate and the effects of temperature, oxygen pressure, catalyst dosage, and concentration of the organic compounds on the TOC and COD Cr removal rates were studied. The degradation kinetics of landfill leachate was also investigated and an exponential experiential model consisting of four influential factors was established to describe the reduction of the organic compounds in the landfill leachate. Meanwhile, the GC-MS technique was used to detect the components of the organic intermediates for the inference of the decomposition mechanisms of the organic compounds in landfill leachate. The results reveal that the reaction temperature and the catalyst dosage are the most important factors affecting the degradation reaction of the organic compounds and that the principal intermediates confirmed by GC-MS are organic acids at a percentage of more than 88% with no aldehydes or alcohols detected. The decomposition mechanisms of the organic compounds in landfill leachate were inferred based on the GC-MS information as follows: the activated gas phase O 2 captured the hydrogen of the organic pollutants to produce free radicals, which then initiated the catalytic reaction. So most of the organic compounds were oxidized into CO 2 and H 2O ultimately. In general, catalytic wet air oxidation over catalyst Co 3O 4/Bi 2O 3 was a very promising technique for the treatment of landfill leachate.
基金This project is supported by the Natural High Tech. R&D Program of China (No. 2002AA601260)
文摘A kind of CWAO catalyst, RuO_2/γ-Al_2O_3, was prepared by dipping Al_2O_3into the aqueous solution of RuCl_3·3H_2O. XRD, SEM and TEM were used to determine the catalyticstructure. Influences of the calcination temperature, the initial pH of the feed solution anddegradation temperature on the activity of the RuO_2/γ-Al_2O_3 catalyst were investigated and thereaction mechanism was preliminarily studied. Results showed that uniform dispersion of RuO_2crystallites was observed on the surface of the catalyst. The activity of the catalyst was higher atcalcination temperature of 300℃ for 3 h and the particle reunion occurred and some large RuO_2crystallites were abundant at high calcination temperature of 500℃ The activity of the catalyst wasbetter in the acid solution than in the alkaline solution. Increasing degradation temperature andusing the catalyst could shorten the induction periods so that the phenol and COD removal wereincreased. For RuO_2/γ-Al_2O_3 catalyst, the phenol and COD removal were respectively 98% and 80%in a temperature of 150℃, pH of 5.6 and pressure of 3 MPa after a 2 h reaction. This indicated thatRu/γ-Al_2O_3 catalyst had good activity.
文摘Polyvinyl alcohol (PVA)-containing desizing wastewater was treated by various wet oxidation methods.Parameters such as reaction temperature, initial solution pH, and the dosage of H2O2 were investigated in terms of chemical oxygen demand (CODcr) and total organic carbon (TOC) removal rate. Up to 90% of the initial CODcr was removed by wet air oxidation(WAO) at 270℃ with stoichiometric oxygen supply, while at temperature of 200℃, the CODcr removal rate was found to be 80%. Similar results were obtained by Promoted WAO (PWAO) and wet peroxide oxidation(WPO) at a lower temperature of 150℃. Reaction temperature was found to have a significant effect on the oxidation performance for all the methods. Initial solution pH was observed to play a significant role in PWAO and WPO where H2O2 was employed. Comparison of WAO, CWAO(catalytic wet air oxidation), PWAO and WPO shows that the rate of CODcr removal increases in the order: WAO, CWAO, PWAO and WPO.
基金the Shanxi Provin-cial Youth Science and Technology Research Fund (No.2008021009-2) for the financial support to this project
文摘The removal of hydrogen sulfide from gas plays an important role in rational utilization of resources and environ- mental protection. In this paper, the process of hydrogen sulfide removal by wet oxidation method in a rotating packed bed was investigated in a scale for treating 10 000 Nm3/h of gas. On the basis of studying the influence of the species and con- centration of alkali source, the liquid/gas volume ratio, the high gravity factor, and the hydrogen sulfide content in feed gas on the desulfurization effect, the suitable technological conditions were obtained. The hydrogen sulfide removal efficiency could reach 98.0% under these conditions. The results of continuous operation of process facilities showed that the high gravity method has many merits including higher desulfurization rate, good stability in operation, lower liquid/gas volume ratio, greater operation elasticity, and apparent energy saving effects.
基金Project (No. 20407015) supported by the National Natural ScienceFoundation of China
文摘Catalytic wet air oxidation (CWAO) of o-chlorophenol in wastewater was studied in a stainless steel autoclave using four different Fe catalysts in the temperature range of 100?200 °C. Experimental results showed that high rate of o-chlorophenol and CODCr (Chemical Oxygen Demand, mg/L) removal by CWAO was obtained at relatively low temperature and pressure. The catalysts Fe2(SO4)3, FeSO4, Fe2O3 and FeCl3 all exhibited high catalytic activity. More than 93.7% of the initial CODCr and nearly 100% of o-chlorophenol were removed at 150 °C after 150 min with FeSO4 as catalyst. The CWAO of o-chlorophenol was found to be pseudo-first order reaction with respect to o-chlorophenol, with activation energy of 75.56 kJ/mol in the temperature range of 100-175 °C.
基金Supported by the Natural Science Foundation of Guangdong Province(2014A030312007)the China Postdoctoral Science Foundation(2014M552202)the Started Project for Professor of Hanshan Normal University(QD20140615)
文摘A Cu–Fe–La/γ-Al_2O_3(CFLA) catalyst was prepared by the excessive impregnation method and characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The results indicate that the catalyst contained mostly Cu^(2+), Fe^(3+), and La^(3+)and a small amount of Cu^+, Fe^(2+), and La. The active components were uniformly distributed in the catalyst, and the particle size of the components was approximately 7.5 nm. The CFLA catalyst was used for the treatment of methyl orange(MO) solution by catalytic wet air oxidation(CWAO), and it exhibited a high catalytic activity. The catalytic reaction involved variable valence states of metals and free-radical reaction mechanism. The CWAO reaction of MO solution was fitted by a segmented first-order dynamic model, and the rapid reaction apparent activation energy was 13.9 k J·mol^(-1).
文摘Four metal oxide catalysts composed of copper(Cu), stannum(Sn), copper-stannum(Cu-Sn) and copper-cerium(Cu-Ce) respectively were prepared by the co-impregnation method, and γ-alumina(γ-Al 2O 3) is selected as support. A first-order kinetics model was established to study the catalytic wet air oxidation of phenol at different temperature when these catalysts were used. The model simulations are good agreement with present experimental data. Results showed that the reaction rate constants can be significantly increased when catalysts were used, and the catalyst of 6% Cu—10%Ce/γ-Al 2O 3 showed the best catalytic activity. This is consistent with the result of catalytic wet air oxidation of phenol and the COD removal can be arrived at 98.2% at temperature 210℃, oxygen partial pressure 3 MPa and reaction time 30 min. The activation energies of each reaction with different catalysts are nearly equal, which is found to be about 42 kJ/mol and the reaction in this study is proved to be kinetics control.
基金Supported by the Returnee Fourndation of China Ministry of Education.
文摘Catalytic wet air oxidation (CWAO) was investigated in laboratory-scale experiments for the treatment of o-chlorophenol in wastewater. Experimental results showed that wet air oxidation (WAO) process in the absence of catalyst was also effective for o-chlorophenol in wastewater treatment. Up to 80% of the initial CODCr was removed by wet air oxidation at 270℃ with twice amount of the required stoichiometric oxygen supply. At temperature of 150℃, the removal rate of CODCr was only 30%. Fe2(SO4)3, CuSO4, Cu(NO3)2 and MnSO4 exhibited high catalytic activity. Higher removal rate of CODCr was obtained by CWAO. More than 96% of the initial CODCr was removed at 270℃ and 84.6%-93.6% of the initial CODCr was removed at 150℃. Mixed catalysts had better catalytic activity for the degradation of o-chlorophenol in wastewater.
基金Project supported by the Beijing Municipal Natural Science Foundation,China(Grant No.4202078).
文摘A narrowed Si_(0.7)Ge_(0.3)channel fin field-effect transistor(FinFET)device is demonstrated in detail by using an accuratecyclic wet treatment process.The Si_(0.7)Ge_(0.3)fin/per side of 0.63 nm in thickness can be accurately removed in each cycleby utilizing a self-limited oxidation with 40%HNO_(3)solution in 40 s and oxidation removal can be achieved with 1%HFsolution in 10 s.As a result,after the dummy gate removal,the fin width of Si_(0.7)Ge_(0.3)can be narrowed from 20 nm to 8 nmby utilizing 10 cycles of this wet treatment process.Compared with the conventional Si_(0.7)Ge_(0.3)FinFET under a similarprocess,the narrowed Si_(0.7)Ge_(0.3)channel FinFET can realize a strong gate control capability by using this newly developedwet treatment process,because its subthreshold slope can be reduced by 24%,improving from 87 mV/dec to 64 mV/dec.
文摘Two series of cobalt(Ⅲ)\|containing spinel catalysts were prepared by the decomposition of the corresponding nitrates. The catalysts doped with bismuth oxide exhibit a higher activity in the wet air oxidation of acetic acid than those without dopant bismuth oxide. The catalysts were investigated by XRD,TEM,ESR,UV\|DRS and XPS,and the interaction between Co and Bi was studied as well. It has been found that nano\|sized bismuth oxide is paved on the surface of cobalt spinel crystal and the structures of cobalt(Ⅲ)\|containing spinel are still maintained. The shift of the binding energy of Bi\-\{\%4f\%\-\{7/2\}\} is related to the catalytic activity of these catalysts doped with bismuth oxide.
文摘The pretreatment technology of wet air oxidation(WAO) and coagulation and acidic hydrolysis for apramycin wastewater was investigated in this paper. The COD, apramycin, NH^+_4 concentration, and the ratio of BOD_5/COD were analyzed, and the color and odor of the effluent were observed. WAO of apramycin wastewater, without catalyst and with RuO_2/Al_2O_3 and RuO_2-CeO_2/Al_2O_3 catalysts, was carried out at degradation temperature of 200℃ and the total pressure of 4 MPa in a 1 L batch reactor. The result showed that the apramycin removals were respectively 50 2% and 55 0%, COD removals were 40 0% and 46 0%, and the ratio of BOD_5/COD was increased to 0 49 and 0 54 with RuO_2/Al_2O_3 and RuO_2-CeO_2/Al_2O_3 catalysts in catylytic wet air oxidation(CWAO) after the reaction of 150 min. With the pretreatment of coagulation and acidic hydrolysis, COD and apramycin removals were slight decreased, and the ratio of BOD_5/COD was increased to 0 45, and the effluents was not suitable to biological treatment. The color and odor of the wastewater were effectively controlled and the reaction time was obviously shortened with WAO. HO_2· may promote organic compounds oxidized in WAO of the apramycin wastewater. The addition of CeO_2 could promote the activity and stability of RuO_2/Al_2O_3 in WAO of apramycin wastewater.
基金financial support of the Twelfth Five-Year National Science and Technology Support Program(2014BAD02B02)
文摘In this paper, we described the optimization of the wet oxidation pretreatment conditions to enhance enzymatic hydrolysis efficiency, using poplar waste from the stock section of a paper mill as the raw material. We showed that the optimal conditions of the pretreatment for poplar waste were an initial p H value of 10, a temperature of 195℃, a holding time of 15 min, and an oxygen pressure of 1.2 MPa. In this case, the yield of the obtained solid material produced by the process was 51.7% and the reducing sugar yield was 46.8%. The solid part obtained from the pretreatment process was hydrolyzed by cellulase L-10. The optimal enzymatic conditions were a temperature of 49℃, a duration time of 56 h, an enzyme dosage of 38 FPU/g at a p H value of 4.8, and a solid-to-liquor ratio of 1∶50. The resulting cellulose conversion rate reached 96.4% in terms of the pretreated substances. In addition, a chemical composition analysis of the poplar waste and pretreated material indicated that about 92% of the hemicelluloses and 43% of the lignin in the raw material were degraded and dissolved. In addition, the crystallization decreased from 57.5% to 54.8%. An obvious fibrillation of the fiber pretreated by the wet oxidization process was observed by SEM. Moreover, high-performance liquid chromatography(HPLC) results showed a high xylose content and monosaccharide degradation products in the pretreatment solution. In conclusion, the wet oxidation pretreatment process could efficiently degrade or remove the lignin and hemicellulose, as well as reduce the crystallinity of the lignocellulosic material, which resulted in animprovement of the enzymatic ability and an increase in the cellulose conversion rate.