Single-phase full-color Ba_3Lu_2(SiO_4)_3:Eu^(2+) phosphor for white-light emitting diodes

we developed a new silicate-based full-color phosphor Ba3Lu2（SiO4）3：Eu2＋ through solid state reaction.The host crystal structure was isostructural with Ca3Y2（SiO4）3 instead of garnet-type.The phosphor absorbed near-ultraviolet light from 250 to 400 nm,which was very suitable for a color converter of white LED that used UV-LED as the primary light source.The photoluminescence peak wavelength of Ba3Lu2（SiO4）3：Eu2＋ was about 461 nm and a shoulder peak was around 522 nm,which resulted from the 5d-4f transition of the Eu2＋.The optimum concentration of Eu2＋ was 3.45 mol.% of Ba2＋ content in Ba3Lu2（SiO4）3 host.It is a promising candidate for application in white LED as a white light converter.

Interface engineering yields efficient perovskite light-emitting diodes

Metal-halide perovskites(MHPs)have emerged as a new class of semiconductors used in perovskite solar cells(PSCs)[1-5],perovskite light-emitting diodes(PeLEDs)[6-12],photo/X-ray detectors[13-16],and memristors[17,18].Pe LEDs can emit different light with high purity[19,20].

Materials and device engineering to achieve high-performance quantum dots light emitting diodes for display applications

Quantum dots(QDs)have attracted wide attention from academia and industry because of their advantages such as high emitting efficiency,narrow half-peak width,and continuously adjustable emitting wavelength.QDs light emitting diodes(QLEDs)are expected to become the next generation commercial display technology.This paper reviews the progress of QLED from physical mechanism,materials,to device engineering.The strategies to improve QLED performance from the perspectives of quantum dot materials and device structures are summarized.

Green Vertical‑Cavity Surface‑Emitting Lasers Based on InGaN Quantum Dots and Short Cavity

Room temperature low threshold lasing of green GaNbased vertical cavity surface emitting laser(VCSEL)was demonstrated under continuous wave(CW)operation.By using self-formed InGaN quantum dots(QDs)as the active region,the VCSEL emitting at 524.0 nm has a threshold current density of 51.97 A cm^(-2),the lowest ever reported.The QD epitaxial wafer featured with a high IQE of 69.94%and theδ-function-like density of states plays an important role in achieving low threshold current.Besides,a short cavity of the device(~4.0λ)is vital to enhance the spontaneous emission coupling factor to 0.094,increase the gain coefficient factor,and decrease the optical loss.To improve heat dissipation,AlN layer was used as the current confinement layer and electroplated copper plate was used to replace metal bonding.The results provide important guidance to achieving high performance GaN-based VCSELs.

A green-yellow emitting β-Sr_2SiO_4:Eu^(2+) phosphor for near ultraviolet chip white-light-emitting diode

Sr2SiO4：xEu^2＋ phosphors were synthesized through the solid-state reaction technique. The crystal phase of Sr2SiO4：xEu^2＋ phosphor manipulated by Eu^2＋ concentration was studied. The phase transited from β to α＇ in Sr2SiO4：xEu^2＋ phosphor with increasing europium concentration. The single β phase was formed as x≤005 and changed α＇ phase when x〉0.01. The emission spectrum of the β-Sr2SiO4：Eu^2＋ phosphor consisted of a green-yellow broadband peaking at around 540 nm and a blue band at 470 nm under near ultraviolet excitation. The white LEDs by combining near ultraviolet chips with β-Sr2SiO4：Eu^2＋ phosphors were fabricated. The luminous efficiency （15.7lm/W） was higher than α＇-Sr2SiO4：Eu^2＋ phosphor white LED.

Fabrication of High Color Rendering Index White Light Emitting Diodes from Gold Nanoclusters

We demonstrated gold nanoclusters as color tunable emissive light converters for the application of white light emitting diodes (WLEDs). A blue LED providing 460 nm to excite gold nanoclusters mixed with UV curable material generates broad bandwidth emission at the visible range. Increasing the amount of gold nanoclusters, the correlated color temperature of WLEDs tuned from cold white to warm white, and also results in the variation of color rendering index (CRI). The highest CRI in the experiment is 92.

Standard-definition White-light,High-definition White-light versus Narrow-band Imaging Endoscopy for Detecting Colorectal Adenomas:A Multicenter Randomized Controlled Trial

Objective This study aimed to compare the performance of standard-definition white-light endoscopy(SD-WL),high-definition white-light endoscopy(HD-WL),and high-definition narrow-band imaging(HD-NBI)in detecting colorectal lesions in the Chinese population.Methods This was a multicenter,single-blind,randomized,controlled trial with a non-inferiority design.Patients undergoing endoscopy for physical examination,screening,and surveillance were enrolled from July 2017 to December 2020.The primary outcome measure was the adenoma detection rate(ADR),defined as the proportion of patients with at least one adenoma detected.The associated factors for detecting adenomas were assessed using univariate and multivariate logistic regression.Results Out of 653 eligible patients enrolled,data from 596 patients were analyzed.The ADRs were 34.5%in the SD-WL group,33.5%in the HD-WL group,and 37.5%in the HD-NBI group(P=0.72).The advanced neoplasm detection rates(ANDRs)in the three arms were 17.1%,15.5%,and 10.4%(P=0.17).No significant differences were found between the SD group and HD group regarding ADR or ANDR(ADR:34.5%vs.35.6%,P=0.79;ANDR:17.1%vs.13.0%,P=0.16,respectively).Similar results were observed between the HD-WL group and HD-NBI group(ADR:33.5%vs.37.7%,P=0.45;ANDR:15.5%vs.10.4%,P=0.18,respectively).In the univariate and multivariate logistic regression analyses,neither HD-WL nor HD-NBI led to a significant difference in overall adenoma detection compared to SD-WL(HD-WL:OR 0.91,P=0.69;HD-NBI:OR 1.15,P=0.80).Conclusion HD-NBI and HD-WL are comparable to SD-WL for overall adenoma detection among Chinese outpatients.It can be concluded that HD-NBI or HD-WL is not superior to SD-WL,but more effective instruction may be needed to guide the selection of different endoscopic methods in the future.Our study’s conclusions may aid in the efficient allocation and utilization of limited colonoscopy resources,especially advanced imaging technologies.

Peripheral carbazole units-decorated MR emitter containing B−N covalent bond for highly efficient green OLEDs with low roll-off

Boron−nitrogen doped multiple resonance(BN-MR)emitters,characterized by B−N covalent bonds,offer distinctive advantages as pivotal building blocks for facile access to novel MR emitters featuring narrowband spectra and high efficiency.However,there remains a scarcity of exploration concerning synthetic methods and structural derivations to expand the library of novel BN-MR emitters.Herein,we present the synthesis of a BN-MR emitter,tCz[B−N]N,through a one-pot borylation reaction directed by the amine group,achieving an impressive yield of 94%.The emitter is decorated by incorporating two 3,6-di-tbutylcarbazole(tCz)units into a B−N covalent bond doped BN-MR parent molecule via para-C−π−D and para-N−π−D conjugations.This peripheral decoration strategy enhances the reverse intersystem crossing process and shifts the emission band towards the pure green region,peaking at 526 nm with a narrowband full-width at half maximum(FWHM)of 41 nm.Consequently,organic light emitting diodes(OLEDs)employing this emitter achieved a maximum external quantum efficiency(EQEmax)value of 27.7%,with minimal efficiency roll-off.Even at a practical luminance of 1000 cd·m^(−2),the device maintains a high EQE value of 24.6%.

Very-High Color Rendering Index Hybrid White Organic Light-Emitting Diodes with Double Emitting Nanolayers

A very-high color rendering index white organic light-emitting diode(WOLED) based on a simple structure was successfully fabricated. The optimized device exhibits a maximum total efficiency of 13.1 and 5.4 lm/W at 1,000 cd/m2. A peak color rendering index of 90 and a relatively stable color during a wide range of luminance were obtained. In addition, it was demonstrated that the 4,40,400-tri(9-carbazoyl) triphenylamine host influenced strongly the performance of this WOLED.These results may be beneficial to the design of both material and device architecture for high-performance WOLED.

Internal quantum efficiency drop induced by the heat generation inside of light emitting diodes (LEDs)

The reasons for low output power of AlGalnP Light Emitting Diodes （LEDs） have been analysed. LEDs with AlGaInP material have high internal but low external quantum efficiency and much heat generated inside especially at a large injected current which would reduce both the internal and external quantum efficiencies. Two kinds of LEDs with the same active region but different window layers have been fabricated. The new window layer composed of textured 0.5 μm GaP and thin Indium-Tin-Oxide film has shown that low external quantum efficiency （EQE） has serious impaction on the internal quantum efficiency （IQE）, because the carrier distribution will change with the body temperature increasing due to the heat inside, and the test results have shown the evidence of LEDs with lower output power and bigger wavelength red shift.

Synthesis and luminescent properties of polycrystalline Gd_2(MoO_4)_3:Dy^(3+) for white light-emitting diodes

Polycrystalline Gd2(MoO4)3:Dy3+ phosphors have been synthesized by high temperature solid-state reaction method. The phosphors were characterized with X-ray diffractometer, thermogravimetric analysis and different scanning calorimeter, scanning electron microscopy, and photoluminescence spectrofluorimeter. Several peaks at 351, 389, 425, 452, and 472 nm appeared in photoluminescence excitation spectrum, which matched well with the emission of the ultraviolet (UV) and blue-light emitting diode (LED) chips. Upon excitation at 389 nm UV light, intense emissions centered at 484, 575 and 668 nm were attributed to the transitions of 4F9/2→6H15/2, 4F9/2→6H13/2 and 4F9/2→6H11/2 of Dy3+, respectively. The chromaticity coordinates and correlative color temperatures have been calculated and presented in the Commission International de I’Eclairage (CIE) diagrams. The results indicated that Gd1.9(MoO4)3:Dy0.13+ with CIE coordinates of (x=0.38, y=0.41) and the correlative color temperature of 4134 K is a potential candidate for white LEDs.

Metal–organic–vapor phase epitaxy of InGaN quantum dots and their applications in light-emitting diodes

InGaN quantum dot is a promising optoelectronic material, which combines the advantages of low-dimensional and wide-gap semiconductors. The growth of InGaN quantum dots is still not mature, especially the growth by metal--organic- vapor phase epitaxy （MOVPE）, which is challenge due to the lack of, itin-situ monitoring tool. In this paper, we reviewed the development of InGaN quantum dot growth by MOVPE, including our work on growth of near-UV, green, and red InGaN quantum dots. In addition, we also introduced the applications of InGaN quantum dots on visible light emitting diodes.

Near-infrared lead chalcogenide quantum dots:Synthesis and applications in light emitting diodes

This paper reviews the recent progress in the synthesis of near-infrared(NIR) lead chalcogenide(PbX;PbX = PbS,PbSe, PbTe) quantum dots(QDs) and their applications in NIR QDs based light emitting diodes(NIR-QLEDs). It summarizes the strategies of how to synthesize high efficiency PbX QDs and how to realize high performance Pb X based NIR-QLEDs.

White light-emitting diodes from perovskites

White light-emitting diodes(WLEDs),as key infrastructure,play an important role in the field of lighting and display.In the past few decades,many methods were developed to prepare WLEDs.A common strategy is to use blue LEDs to excite yttrium aluminum garnet(YAG)phosphors and generate composite white light,which is now the main technology for commercial lighting.In 2014,Nobel Prize in Physics was awarded to Nakamura et al.for their contribution to blue LEDs[1,2].

Potential red-emitting phosphor GdNbO_4:Eu^(3+),Bi^(3+) for near-UV white light emitting diodes

A red-emitting phosphor GdNbO4：Eu3＋,Bi3＋ was prepared by a high temperature solid-state reaction technique. The phosphor was characterized by X-ray diffraction （XRD）, particle size analyzer and fluorescence spectrometer. The single phase of GdNbO4：Eu3＋,Bi3＋ was obtained at 1150~C and the average particle diameter was about 2.30 μm. Excitation and emission spectra reveal that the phosphor can be ef- ficiently excited by ultraviolet （UV） light （394 nm） and emit the strong red light of 612 nm due to the Eu3＋ transition of SD0~TF2. The opti- mum content of Eu3＋ doped in the phosphor GdNbOn：Eu3＋ is 20mo1%. The phosphor Gdo.80NbO4：0.20Eu3＋,0.03Bi3＋ shows much stronger photoluminescence intensity and better chromaticity coordinates （x=0.642, 0.352） than GdNbO4：Eu3＋. It is confirmed that Gdo.80NbO4：0.20Eu3＋,0.03Bi3＋ is a potential candidate for near-UV chip-based white light emitting diodes.

Organic Light Emitting Diodes with Lithium Contained Alq3 as Electron Injection Layer

lNovel lithium doped tris 8 hydroxylquinoline aluminium(Alq3:Li) layer is deposited between emission layer and electron injection aluminium electrode as an electron injection assistant layer in different organic light emitting diodes(OLED) to lower the electron injection barrier. In these devices, Alq3 is used as emission layer, and a bilayer film of N,N bis (1 naphhyl) N,N diphenyl 1,1 biphenyle 4,4' diamine(NPB) and 4,4,4' tris(3 methyl phenylphenylamino) triphenylamine( m MTDATA) used as hole transport layer(HTL). The electroluminescent performance of devices with different thicknesses of Alq3∶Li shows that the insertion of the lithium doped Alq3 layer can reduce the turn on voltage by at least 2 volts, and the stability of devices with this lithium doped Alq3 layer is improved too. It can also change the efficiency of devices. Compared with an ultra thin lithium fluoride(LiF) layer, Alq3∶Li sheet gives similar effects but higher efficiency and can be much thicker and hence it is easier to control the deposition.

Organic light emitting diodes using magnesium doped organic acceptor as electron injection layer and silver as cathode

Organic light emitting diodes employing magnesium doped electron acceptor 3, 4, 9, 10 perylenetetracarboxylic dianhydride （Mg：PTCDA） as electron injection layer and silver as cathode were demonstrated. As compared to Mg ： Ag cathode, the combination of the Mg ： PTCDA layer and silver provided enhanced electron injection into tris （8- quinolinolato） aluminium. The device with 1 ： 2 Mg ： PTCDA and Ag showed an increase of about 12% in the maximum current efficiency, mainly due to the improved hole-electron balance, and an increase of about 28% in the maximum power efficiency, as compared to the control device using Mg ： Ag cathode. The properties of Mg ： PTCDA composites were studied as well.

Multifunctional silicon-based light emitting device in standard complementary metal oxide semiconductor technology

A three-terminal silicon-based light emitting device is proposed and fabricated in standard 0.35 μm complementary metal-oxide-semiconductor technology. This device is capable of versatile working modes： it can emit visible to near infra-red （NIR） light （the spectrum ranges from 500 nm to 1000 nm） in reverse bias avalanche breakdown mode with working voltage between 8.35 V-12 V and emit NIR light （the spectrum ranges from 900 nm to 1300 nm） in the forward injection mode with working voltage below 2 V. An apparent modulation effect on the light intensity from the polysilicon gate is observed in the forward injection mode. Furthermore, when the gate oxide is broken down, NIR light is emitted from the polysilicon/oxide/silicon structure. Optoelectronic characteristics of the device working in different modes are measured and compared. The mechanisms behind these different emissions are explored.

Pure blue and white light electroluminescence in a multilayer organic light-emitting diode using a new blue emitter

We characterized the 6,12-bis{[N-（3,4-dimethylphenyl）-N-（2,4,5-trimethylphenyl）]amino} chrysene （BmPAC）, which has been proven to be a blue fluorescent emission with high EL efficiency. The blue fluorescent device exhibits good performance with an external quantum efficiency of 5.8% and current efficiency of 8.9 cd/A, respectively. Using BmPAC, we also demonstrate a hybrid phosphorescence/fluorescence white organic light-emitting device （WOLED） with high efficiency of 36.3 cd/A. In order to improve the relative intensity of blue light, we plus a blue light-emitting layer （BEML） in front of the orange light emitting layer （YEML） to take advantage of the excess singlet excitons. With the new emitting layer of BEML/YEML/BEML, we demonstrate the fluorescence/phosphorescence/fluorescence WOLED exhibits good performance with a current efficiency of 47 cd/A and an enhanced relative intensity of blue light.

Luminescence characteristics of Eu^(3+) activated borate phosphor for white light emitting diode

In this paper, the Sr3Y2 （BO3）4 ：Eu^3＋ phosphor was synthesized by high temperature solid-state reaction method and the luminescence characteristics were investigated. The emission spectrum exhibits one strong red emission at 613 nm corresponding to the electric dipole 5^Do-7^F2 transition of Eu^3＋ under 365 nm excitation, this is because Eu^3＋ substituted for Y^3＋ occupied the non-centrosymmetric position in the crystal structure of Sr3Y2（BO3）4. The excitation spectrum indicates that the phosphor can be effectively excited by ultraviolet （254 nm, 365 nm and 400 nm） and blue （470 nm） light. The effect of Eu^3＋ concentration on the red emission of Sr3Y2（BO3）4 ：Eu^3＋ was measured, the result shows that the emission intensities increase with increasing Eu^3＋ concentration, then decrease. The Commission Internationale del＇Eclairage chromaticity （x, y） of Sr3Y2（BO3）4 ：Eu^3＋ phosphor is （0.640, 0.355） at 15 mol% Eu^3＋.