Aiming at the signal bandwidth design problem for multi-target imaging task,a kind of multiple input multiple output(MIMO)radar waveform design method is proposed.At first,the closed-loop feedback between the range pr...Aiming at the signal bandwidth design problem for multi-target imaging task,a kind of multiple input multiple output(MIMO)radar waveform design method is proposed.At first,the closed-loop feedback between the range profile and the signal bandwidth,which can design the minimum bandwidth of a transmitting signal that can distinguish each scatterer of the target in range direction,is established.Then,considering the request of beam pattern and the bandwidth limitation,a waveform optimization model is established and solved.Therefore,the multi-target observation and the dynamic adjustment of the signal bandwidth are accomplished.In the end,the simulation results prove the performance of the algorithm in a low SNR circumstance.展开更多
In high voltage input DC-DC converter, auxiliary winding of isolation transformer is usually used to supply power for control circuit. Due to the wide-range of input voltage, the variable output voltage of auxiliary w...In high voltage input DC-DC converter, auxiliary winding of isolation transformer is usually used to supply power for control circuit. Due to the wide-range of input voltage, the variable output voltage of auxiliary winding will cause a series of problems, such as variable drive pulse amplitude, increased driver switching devices loss and drive transformer core saturation. This paper analyzes the influence of variable output voltage of auxiliary winding in detail. A novel method is proposed to solve the problem of large variation range of auxiliary winding output voltage, which is adding a buck converter between the auxiliary winding and the control circuit. A dual switch forward convert has been designed with 300 V - 800 V input and 24 V/5 A output. The results show that this method is effective by comparing the different results of using buck converter or not.展开更多
High Resolution Wide Swath (HRWS) Synthetic Aperture Radar (SAR) often suffers from low Signal-to-Noise Ratio (SNR) due to small transmitting antenna, especially in phased array antenna systems. Digital Beam Forming (...High Resolution Wide Swath (HRWS) Synthetic Aperture Radar (SAR) often suffers from low Signal-to-Noise Ratio (SNR) due to small transmitting antenna, especially in phased array antenna systems. Digital Beam Forming (DBF) based on Single Input and Multiple Output (SIMO) achieves receiving array gain at the cost of increasing data rate. This letter proposes a new HRWS SAR method, which employs intra-pulse null steering to get receiving gain in elevation and decrease the data rate, and Multiple Input and Multiple Output (MIMO) using Space-Time Block Coding (STBC) in azimuth to get transmitting gain and receiving array gain simultaneously. The feasibility is verified by deduction and simulations.展开更多
Mutual coupling reduction or isolation enhancement in antenna arrays is an important area of research as it severely affects the performance of an antenna.In this paper,a new type of compact and highly isolated Multip...Mutual coupling reduction or isolation enhancement in antenna arrays is an important area of research as it severely affects the performance of an antenna.In this paper,a new type of compact and highly isolated Multiple-Input-Multiple-Output(MIMO)antenna for ultra-wideband(UWB)applications is presented.The design consists of four radiators that are orthogonally positioned and confined to a compact 40×40×0.8 mm3 space.The final antenna design uses an inverted L shape partial ground to produce an acceptable reflection coefficient(S11<−10 dB)in an entire UWB band(3.1–10.6)giga hertz(GHz).Moreover,the inter-element isolation has also been enhanced to>20 db for majority of the UWB band.The antenna was fabricated and tested with the vector network analyzer(VNA)and in an anechoic chamber for scattering parameters and radiation patterns.Furthermore,different MIMO diversity performance metrics are also measured to validate the proposed model.The simulation results and the experimental results from the constructed model agree quite well.The proposed antenna is compared with similar designs in recently published literature for various performance metrics.Because of its low envelope correlation coefficient(ECC<0.1),high diversity gain(DG>9.99 dB),peak gain of 4.6 dB,reduced channel capacity loss(CCL<0.4 b/s/Hz),and average radiation efficiency of over 85%,the proposed MIMO antenna is ideally suited for practical UWB applications.展开更多
Power generation using dielectric elastomer transducers is cheap, light, stackable, easy to install, and highly efficient. Also, since the dielectric elastomer transducer is an actuator developed into an artificial mu...Power generation using dielectric elastomer transducers is cheap, light, stackable, easy to install, and highly efficient. Also, since the dielectric elastomer transducer is an actuator developed into an artificial muscle, if the DE motor is further developed, it might be possibly be able to drive a vehicle. Efficient robot driving, various industrial machines and the use of dielectric elastomer sensors to optimize the driving may also help solve the above problems from the perspective of eco-driving. This paper describes the latest level of development of dielectric elastomers, their main problems and solutions to these problems, and their potential applications. The possibilities and concrete plans for building local global smart cities (including local generation power for local consumption), efficient transportation, and environmental monitoring systems utilizing dielectric elastomers are also discussed.展开更多
Two novel schemes are proposed to synthesize high resolution range profile (HRRP) based on co-located multiple-input multiple-output (MIMO) system in the context of the joint radar and communication system. The differ...Two novel schemes are proposed to synthesize high resolution range profile (HRRP) based on co-located multiple-input multiple-output (MIMO) system in the context of the joint radar and communication system. The difference between two schemes is the pattern of selecting pulses, which depends on the demand for the velocity information. The system, a type of frequency diverse array (FDA), takes full advantage of the phase-coded orthogonal frequency division multiplexing (OFDM) signal. Furthermore, the complete discrete form of the phase-coded OFDM echoes is utilized to derive the HRRP processing. The velocity estimation in the second scheme aims to eliminate velocity ambiguity, and high velocity can be retrieved exactly. Meanwhile, the imaging method is investigated with random frequency coding applied to an array. The desired performance of resolving velocity ambiguity and suppressing noise is shown by means of comparisons with previous work. The advantages in the radar imaging and the significance of the work are concluded in the end.展开更多
A fully integrated Ku-band voltage controlled oscillator （VCO） is presented in an InGaP/GaAs hetero- junction bipolar transistor （HBT） technology. To achieve the wide tuning range （TR）, the VCO employs a Colpitt...A fully integrated Ku-band voltage controlled oscillator （VCO） is presented in an InGaP/GaAs hetero- junction bipolar transistor （HBT） technology. To achieve the wide tuning range （TR）, the VCO employs a Colpitts configuration, and the VCO simultaneously achieves high output power. The implemented VCO demonstrates an oscillation frequency range from 12.82 to 14.97 GHz, a frequency TR of 15.47%, an output power from 0.31 to 6.46 dBm, and a phase noise of -94.9 dBc/Hz at 1 MHz offset from 13.9 GHz center frequency. The VCO con- sumes 52.75 mW from 5 V supply and occupies an area of 0.81 × 0.78 mm2. Finally, the figures-of-merit for VCOs is discussed.展开更多
Given the statistical gaps in material flow among provinces in China, a method was introduced to estimate regional physical imports and exports （RPIE）, which includes international and interregional imports/ exports...Given the statistical gaps in material flow among provinces in China, a method was introduced to estimate regional physical imports and exports （RPIE）, which includes international and interregional imports/ exports. This method uses provincial monetary input- output tables （MIOT） and international trade statistics. A coefficient matrix representing correlations between monetary value and physical mass for years 2000-2009 was obtained based on a detailed commodity classification and 22 material production sectors in MIOT. With the coefficient matrix as reference, RPIE was measured. Pilot calculation of both regional physical trade balance and domestic material consumption, as well as a brief analysis of these methods, were conducted using 2002 data.展开更多
A CMOS triode transconductor was developed with common mode feedback suitable for operating in low-voltage and low-power applications. The design is based on a body-driven input stage with feedback loops to extend bot...A CMOS triode transconductor was developed with common mode feedback suitable for operating in low-voltage and low-power applications. The design is based on a body-driven input stage with feedback loops to extend both the signal input range and the tuning capability. The effective transconductance of the body-driven triode stage is increased using a partial positive feedback technique which also partially solves the problem introduced by the small transconductance. This design uses the UMC 0.18 μm CMOS process. Simulations show the transconductor operated with 1 V supply voltage has less than -55 dB total harmonic distortions （THD） in the complete tuning range （0 V≤ Vcont≤ 0.43 V） for a 1 MHz 0.8 Vp-p differential input. The power consumption is 70 μW for a 0.43 V control voltage.展开更多
基金Supported by the National Natural Science Foundation of China(61631019)
文摘Aiming at the signal bandwidth design problem for multi-target imaging task,a kind of multiple input multiple output(MIMO)radar waveform design method is proposed.At first,the closed-loop feedback between the range profile and the signal bandwidth,which can design the minimum bandwidth of a transmitting signal that can distinguish each scatterer of the target in range direction,is established.Then,considering the request of beam pattern and the bandwidth limitation,a waveform optimization model is established and solved.Therefore,the multi-target observation and the dynamic adjustment of the signal bandwidth are accomplished.In the end,the simulation results prove the performance of the algorithm in a low SNR circumstance.
文摘In high voltage input DC-DC converter, auxiliary winding of isolation transformer is usually used to supply power for control circuit. Due to the wide-range of input voltage, the variable output voltage of auxiliary winding will cause a series of problems, such as variable drive pulse amplitude, increased driver switching devices loss and drive transformer core saturation. This paper analyzes the influence of variable output voltage of auxiliary winding in detail. A novel method is proposed to solve the problem of large variation range of auxiliary winding output voltage, which is adding a buck converter between the auxiliary winding and the control circuit. A dual switch forward convert has been designed with 300 V - 800 V input and 24 V/5 A output. The results show that this method is effective by comparing the different results of using buck converter or not.
文摘High Resolution Wide Swath (HRWS) Synthetic Aperture Radar (SAR) often suffers from low Signal-to-Noise Ratio (SNR) due to small transmitting antenna, especially in phased array antenna systems. Digital Beam Forming (DBF) based on Single Input and Multiple Output (SIMO) achieves receiving array gain at the cost of increasing data rate. This letter proposes a new HRWS SAR method, which employs intra-pulse null steering to get receiving gain in elevation and decrease the data rate, and Multiple Input and Multiple Output (MIMO) using Space-Time Block Coding (STBC) in azimuth to get transmitting gain and receiving array gain simultaneously. The feasibility is verified by deduction and simulations.
基金Deanship of ScientificResearch,King Abdulaziz University for providing financial vide grant number (KEP-MSc-41-135-1443).
文摘Mutual coupling reduction or isolation enhancement in antenna arrays is an important area of research as it severely affects the performance of an antenna.In this paper,a new type of compact and highly isolated Multiple-Input-Multiple-Output(MIMO)antenna for ultra-wideband(UWB)applications is presented.The design consists of four radiators that are orthogonally positioned and confined to a compact 40×40×0.8 mm3 space.The final antenna design uses an inverted L shape partial ground to produce an acceptable reflection coefficient(S11<−10 dB)in an entire UWB band(3.1–10.6)giga hertz(GHz).Moreover,the inter-element isolation has also been enhanced to>20 db for majority of the UWB band.The antenna was fabricated and tested with the vector network analyzer(VNA)and in an anechoic chamber for scattering parameters and radiation patterns.Furthermore,different MIMO diversity performance metrics are also measured to validate the proposed model.The simulation results and the experimental results from the constructed model agree quite well.The proposed antenna is compared with similar designs in recently published literature for various performance metrics.Because of its low envelope correlation coefficient(ECC<0.1),high diversity gain(DG>9.99 dB),peak gain of 4.6 dB,reduced channel capacity loss(CCL<0.4 b/s/Hz),and average radiation efficiency of over 85%,the proposed MIMO antenna is ideally suited for practical UWB applications.
文摘Power generation using dielectric elastomer transducers is cheap, light, stackable, easy to install, and highly efficient. Also, since the dielectric elastomer transducer is an actuator developed into an artificial muscle, if the DE motor is further developed, it might be possibly be able to drive a vehicle. Efficient robot driving, various industrial machines and the use of dielectric elastomer sensors to optimize the driving may also help solve the above problems from the perspective of eco-driving. This paper describes the latest level of development of dielectric elastomers, their main problems and solutions to these problems, and their potential applications. The possibilities and concrete plans for building local global smart cities (including local generation power for local consumption), efficient transportation, and environmental monitoring systems utilizing dielectric elastomers are also discussed.
基金supported by the National Natural Science Foundation of China(6107116361071164+8 种基金6147119161501233)the Fundamental Research Funds for the Central Universities(NP2014504)the Aeronautical Science Foundation(20152052026)the Electronic&Information School of Yangtze University Innovation Foundation(2016-DXCX-05)the Funding for Outstanding Doctoral Dissertation in NUAA(BCXJ15-03)the Funding of Jiangsu Innovation Program for Graduate Education(KYLX15 0281)the Fundamental Research Funds for the Central Universitiespartly funded by the Priority Academic Program Development of Jiangsu Higher Education Institutions(PADA)
文摘Two novel schemes are proposed to synthesize high resolution range profile (HRRP) based on co-located multiple-input multiple-output (MIMO) system in the context of the joint radar and communication system. The difference between two schemes is the pattern of selecting pulses, which depends on the demand for the velocity information. The system, a type of frequency diverse array (FDA), takes full advantage of the phase-coded orthogonal frequency division multiplexing (OFDM) signal. Furthermore, the complete discrete form of the phase-coded OFDM echoes is utilized to derive the HRRP processing. The velocity estimation in the second scheme aims to eliminate velocity ambiguity, and high velocity can be retrieved exactly. Meanwhile, the imaging method is investigated with random frequency coding applied to an array. The desired performance of resolving velocity ambiguity and suppressing noise is shown by means of comparisons with previous work. The advantages in the radar imaging and the significance of the work are concluded in the end.
基金Project supported by the National Basic Research Program of China(No.2010CBxxxx05)the Advance Research Project of China(No.51308xxxx06)+2 种基金the Advance Research Foundation of China(No.9140A08xxxx11DZ111)Doctoral Scientific Research Foundation of Henan University of Science and Technology(No.400613480011)the Foundation of He’nan Educational Commettee(No.15A510001)
文摘A fully integrated Ku-band voltage controlled oscillator （VCO） is presented in an InGaP/GaAs hetero- junction bipolar transistor （HBT） technology. To achieve the wide tuning range （TR）, the VCO employs a Colpitts configuration, and the VCO simultaneously achieves high output power. The implemented VCO demonstrates an oscillation frequency range from 12.82 to 14.97 GHz, a frequency TR of 15.47%, an output power from 0.31 to 6.46 dBm, and a phase noise of -94.9 dBc/Hz at 1 MHz offset from 13.9 GHz center frequency. The VCO con- sumes 52.75 mW from 5 V supply and occupies an area of 0.81 × 0.78 mm2. Finally, the figures-of-merit for VCOs is discussed.
文摘Given the statistical gaps in material flow among provinces in China, a method was introduced to estimate regional physical imports and exports （RPIE）, which includes international and interregional imports/ exports. This method uses provincial monetary input- output tables （MIOT） and international trade statistics. A coefficient matrix representing correlations between monetary value and physical mass for years 2000-2009 was obtained based on a detailed commodity classification and 22 material production sectors in MIOT. With the coefficient matrix as reference, RPIE was measured. Pilot calculation of both regional physical trade balance and domestic material consumption, as well as a brief analysis of these methods, were conducted using 2002 data.
文摘A CMOS triode transconductor was developed with common mode feedback suitable for operating in low-voltage and low-power applications. The design is based on a body-driven input stage with feedback loops to extend both the signal input range and the tuning capability. The effective transconductance of the body-driven triode stage is increased using a partial positive feedback technique which also partially solves the problem introduced by the small transconductance. This design uses the UMC 0.18 μm CMOS process. Simulations show the transconductor operated with 1 V supply voltage has less than -55 dB total harmonic distortions （THD） in the complete tuning range （0 V≤ Vcont≤ 0.43 V） for a 1 MHz 0.8 Vp-p differential input. The power consumption is 70 μW for a 0.43 V control voltage.
