Antimonene-based saturable absorber for a soliton mode-locked and Q-switched fiber laser in the 2 μm wavelength region

We demonstrate antimonene as a saturable absorber(SA) to generate an ultrafast mode-locked and Q-switched laser in the 2 μm wavelength region. The two antimonene-based SAs were prepared and inserted separately in a thulium–holmiumdoped fiber laser to produce the pulsed laser. Antimonene was coated onto a tapered fiber to generate soliton mode-locked pulses and used in thin-film form for the generation of Q-switched pulses. The mode-locking was stable within a pump power of 267 m W–511 m W, and the laser operated at a central wavelength of 1897.4 nm. The mode-locked laser had a pulse width of 1.3 ps and a repetition rate of 12.6 MHz, with a signal-to-noise ratio of 64 d B. Q-switched laser operation was stable at a wavelength of 1890.1 nm within a pump power of 312 m W–381 m W. With the increase in pump power from 312 m W to 381 m W, the repetition rate increased to a maximum of 56.63 k Hz and the pulse width decreased to a minimum value of 2.85 μs. Wide-range tunability of the Q-switched laser was also realized within the wavelength range of1882 nm–1936 nm.

High stability and low noise laser-diode end-pumped Nd:YAG ceramic passively Q-switched laser at 1123 nm based on a Ti_(3)C_(2)T_(x)-PVA saturable absorber

We report a high repetition frequency, high power stability and low laser noise laser-diode(LD) end-pumped Nd: YAG ceramic passively Q-switched laser at 1123 nm based on a Ti_(3)C_(2)T_(x)-polyvinyl alcohol(PVA) film as a saturable absorber(SA). A Brewster polarizer(BP) and a birefringent crystal(BC) are incorporated to enable frequency selection and filtering for the passively Q-switched 1123 nm pulsed laser to improve the power stability and reduce the noise. When the pump power is 5.1 W, an average output power of 457.9 m W is obtained, corresponding to a repetition frequency of 1.09 MHz,a pulse width of 56 ns, a spectral line width of 0.65 nm, a power instability of ±0.92%, and a laser noise of 0.89%.The successful implementation of the “Ti_(3)C_(2)T_(x)-PVA film passively Q-switching” combined with “frequency selection and filtering of BP + BC” technology path provides a valuable reference for developing pulsed laser with high repetition frequency, high stability and low noise.

A Laser-Diode-Pumped Nd:YAG Laser Q-Switched with a YAG Color Center Chip

A laser-diode-pumped Nd: YAG laser Q-switched Passively with a YAG colorcenter chip has been deveolped. The Q-switched pulse output has a duration of 25-70ns,an energy of about 7.9 μJ and a repetition frequency of 1.25-5.0kHz when the laser cavityparameters and pump power are changed. The Q-switched dynamics is analyzed with therate equation theorry. The theoretical and experimental results agree well.

1.5-MHz repetition rate passively Q-switched Nd:YVO4 laser based on WS2 saturable absorber

A transmission-type tungsten disulfide（WS_2）-based saturable absorber（SA） is fabricated and applied to passively Q-switched Nd：YVO_4 laser.The WS_2 nanosheets are deposited on a quartz substrate by the vertical evaporation method.By inserting the WS2 SA into the plano-concave laser cavity,we achieve 153-ns pulses with an average output power of1.19 W at 1064 nm.To the best of our knowledge,both of them are the best results among those obtained by the Q-switched solid-state lasers with WS_2-based absorbers.The repetition rate ranges from 1.176 MHz to 1.578 MHz.As far as we know,it is the first time that MHz level Q-switched pulses have been generated in all solid state lasers based on low-dimensional materials so far.

A compact graphene Q-switched erbium-doped fiber laser using optical circulator and tunable fiber Bragg grating

We demonstrate a passively Q-switched tunable erbium-doped fiber laser （EDFL） based on graphene as a saturable absorber （SA）. A three-port optical circulator （OC） and a strain-induced tunable fiber Bragg grating （TFBG） are used as the two end mirrors in an all-fiber linear cavity. The Q-switched EDFL has a low pump threshold of 23.8 mW. The pulse repetition rate of the fiber laser can be widely changed from 9.3 kHz to 69.7 kHz by increasing the pump power from 23.8 mW to 219.9 mW. The minimum pulse duration is 1.7 p.s and the highest pulse energy is 25.4 nJ. The emission wavelength of the laser can be tuned from 1560.43 nm to 1566.27 nm by changing the central wavelength of the straininduced TFBG.

High-power xenon lamp-pumped Er:YAP pulse laser operated in free-running and acousto-optical Q-switching modes

We demonstrate a high-energy and high-power pulse laser on a xenon lamp-pumped Er:YAP crystal. The laser performance and thermal focal lengths under different working frequencies are discussed. The results show that the thermal lens effect is gradually aggravated with the increase of working frequencies, and even working at 100 Hz, a single pulse energy of 234 m J can be achieved. A maximum average power of 41.5 W is achieved with a working frequency of 20 Hz and slope efficiency of 2.82%. This output power is much higher than other xenon lamp-pumped erbium laser devices.A Q-switched laser is demonstrated by using the TeO2crystal, the maximum output energies of 11.5 m J and 3.5 m J are obtained at 50 and 100 Hz, the corresponding peak powers are 93.4 k W and 17.2 kW, respectively.The laser wavelengths and beam quality factors are also characterized in the free-running and Q-switched modes. A higher pulse energy and peak power laser could be achieved further by improving the damage threshold of TeO2acousto-optical Q-switching. All the experimental results illustrate that the xenon lamp-pumped Er:YAP laser is a promising candidate for high-power and high-frequency mid-infrared laser devices.

Passively Q-Switched Nd,Cr:YAG Laser Simultaneous Dual-Wavelength Operation at 946 nm and 1.3μm

A diode-end-pumped Q-switched high-efficiency Nd, Cr：YAG laser with simultaneous dual-wavelength emission at 946nm and 1.3μm is demonstrated. The maximum output power of 1.93 W with simultaneous dual-wavelength operation is achieved at an absorbed pump power of 13.32 W and an absorbed slope efficiency of 15.15%. The maximum optical-optical efficiency is 14.49% with pulse widths of 16.38ns at 946nm and 26.65ns at 1.3μm. A maximum total repetition rate of 43.25 kHz is obtained.

Q-Switched Raman Fiber Laser with Molybdenum Disulfide-Based Passive Saturable Absorber

We demonstrate a Q-switched Raman fiber laser using molybdenum disulfide （MoS2） as a saturable absorber （SA）. The SA is assembled by depositing a mechanically exfoliated MoS2 onto a fiber ferrule facet before it is matched with another clean ferrule via a connector. It is inserted in a Raman fiber laser cavity with a total cavity length of about 8kin to generate a Q-switching pulse train operating at 1560.2nm. A 7.7-kin-long dispersion compensating fiber with 584 ps.nm-i km-1 of dispersion is used as a nonlinear gain medium. As the pump power is increased from 395 m W to 422 m W, the repetition rate of the Q-switching pulses can be increased from 132.7 to 137.4 kHz while the pulse width is concurrently decreased from 3.35μs to 3.03μs. The maximum pulse energy of 54.3 nJ is obtained at the maximum pump power of 422 roW. These results show that the mechanically exfoliated MoS2 SA has a great potential to be used for pulse generation in Raman fiber laser systems.

Acousto-Optically Q-Switched Operation of Yb:CNGG Disordered Crystal Laser

We report the repetitively Q-switched laser operation of the Yb-doped calcium niobium gallium garnet disordered garnet crystal, achieved with an acousto-optic modulator in a compact plano-concave resonator that is endpumped by a 935-nm diode laser. An average output power of 1.96 W is produced at pulse repetition rate of50 k Hz at emission wavelengths around 1035 nm, with a slope efficiency of 16%. The highest pulse energy of 269 μJ is generated at pulse repetition rate of 1 k Hz, with pulse width 12.1 ns and peak power 20.53 kW.

Continuous-Wave and Actively Q-Switched Diode-Pumped Er:LuAG Ring Laser at 1650 nm

We demonstrate a cw and actively Q-switched Er：LuAO laser resonantly dual-end-pumped by 1532nm fibre- coupled laser diodes. A maximum cw output power of 1.9W at 1650.3nm is obtained at a pump power of 25.5 W, corresponding to a slope efficiency of 43.3 %. In the Q-switched regime, the maximum pulse energy of 3.51 mJ is reached at a pulse repetition rate of 100 Hz, a pulse duration of 90.5ns and a pump power of 25.5 W. At the repetition rate of 400 Hz, the output energy is 2.12m J, corresponding to a pulse duration of 125.4 ns.

Q-Switched Ytterbium-Doped Fiber Laser Using Black Phosphorus as Saturable Absorber

We demonstrate a Q-switched ytterbium-doped fiber laser （YDFL） using a newly developed multi-layer black phosphorous （BP） saturable absorber （SA）. The BP SA is prepared by mechanically exfoliating a BP crystal and sticking the acquired BP flakes onto a scotch tape. A small piece of the tape is then placed between two ferrules and incorporated in a YDFL cavity to achieve a stable Q-switched operation in a 1.0 μm region. The laser has a pump threshold of 55.1 mW, a pulse repetition rate that is tunable from 8.2 to 32.9 kHz, and the narrowest pulse width of 10.8 μs. The highest pulse energy of 328 nJ is achieved at the pump power of 97.6 mW. Our results show that multi-layer BP is a promising SA for Q-switching laser operation.

Widely Tunable Middle Infrared Optical Parametric Oscillator Pumped by the Q-Switched Ho：GdVO_4 Laser

We demonstrate a middle infrared ZnGeP_2 optical parametric oscillator pumped by the Q-switched Ho：GdVO_4 laser. When the incident Ho pump power is 4.12 W, the maximum average output power of the ZGP-OPO laser is 2.05 W, corresponding to a slope efficiency of 74.6%. The ZGP-OPO laser produces 4.2 ns mid-infrared pulses at a pulse repetition rate of 5 kHz. In addition, we obtain 0.8 um of tunable range for the signal wave and 2.1 um of tunable range for the idler wave.

Q-Switched Erbium-Doped Fiber Laser Using Cadmium Selenide Coated onto Side-Polished D-Shape Fiber as Saturable Absorber

A stable Q-switched erbium doped fiber laser emitting at 1558 nm is demonstrated using a cadmium selenide（CdSe） material coated onto a side-polished D-shape fiber as the saturable absorber（SA）. By elevating the input pump power from the threshold of 91 mW to the maximum available power of 136 mW, a pulse train with a maximum repetition rate of 57.44 kHz, minimum pulse width of 3.76 us, maximum average output power of7.99 mW, maximum pulse energy of 0.1391 uJ, and maximum peak power of 36.99 mW are obtained. The signalto-noise ratio of the spectrum is measured to be around 75 dB. This CdSe based SA is simple, robust, and reliable,and thus suitable for making a portable pulse laser source.

High-energy pulse generation using Yb-doped Q-switched fiber laser based on single-walled carbon nanotubes

An all-fiber laser using a single-walled carbon nanotube（SWCNT） as the saturable absorber（SA） for Q-switched operation in the 1031 nm region is demonstrated in this work. A lasing threshold as low as 17 mW was realized for continuous wave operation. By further increasing the pump power, stable Q-switched pulse trains are obtained when the pump power ranges from 38 mW to 125 mW, corresponding to repetition rate varying from 40.84 kHz to 66.24 kHz, the pulse width from 2.0 μs to 1.0 μs,and the highest single pulse energy of 40.6 nJ respectively.

Efficient Passively Q-Switched Nd:YAG/Cr4+:YAG/LBO Microchip Laser

Performance of an LD-end-pumped passively Q-switched Nd： YA G/Cr4＋ ： YA G microchip laser operating at 1123 nm is studied. A maximum average output power of 517row with an optical-to-optical conversion efficiency of 12.6% and a slope efficiency of 25.8% is obtained under a pump power of 4.1 W. A minimum pulse width of 1.1 ns with a pulse repetition rate of 20.2kHz is obtained, and the corresponding pulse energy and peak power are 25.6μJ and 23.3kW, respectively. To our knowledge, the 23.3kW peak power is the highest among 1123nm lasers. Additionally, based on the 1123 nm laser, with LBO as the frequency doubler, a 288-mW green-yellow laser at 561 nm is successfully achieved.

High-Power Passively Q-Switched Nd:YAG Laser at 1112 nm with a Cr^(4+):YAG Saturable Absorber

A high-power passively Q-switched Nd：YAG laser operating at lll2nm with Cr4＋：yAO as a saturable absorber is demonstrated. Under 808 nm diode-direct pumping, the maximum average output power of 2.73 W is achieved at the pump power of 16.65 W, corresponding to an optical-to-optical conversion efficiency of 16.4%. At the same time, the pulse width, pulse repetition rate, single pulse energy and peak power are 27.2ns, 9 kHz, 303.3#3 and 11.2kW, respectively. As far as we know, the result gives the highest average output power at 1112nm generated by an 808 nm diode-end-pumped Nd：YAG laser.

Erbium-Doped Zirconia-Alumina Silica Glass-Based Fiber as a Saturable Absorber for High Repetition Rate Q-Switched All-Fiber Laser Generation

We propose and demonstrate a Q-switched erbium-doped fiber laser （EDFL） using an erbium-doped zirconia-alumina silica glass-based fiber （Zr-EDF） as a saturable absorber. As a 16-cm-long Zr-EDF is incorporated into a ring EDFL cavity, a stable Q-switching pulse train operating at 1565？nm wavelength is successfully obtained. The repetition rate is tunable from 33.97？kHz to 71.23？kHz by increasing the pump power from the threshold of 26？mW to the maximum of 74？mW. The highest pulse energy of 26.67？nJ is obtained at the maximum pump power.

Zinc-oxide nanoparticle-based saturable absorber deposited by simple evaporation technique for Q-switched fiber laser

A Q-switched erbium-doped fiber laser(EDFL)incorporating zinc-oxide(ZnO)nanoparticles-based saturable absorber(SA)is proposed and demonstrated.To form the SA,the ZnO nanoparticles,which are originally in the powder form,are first dissolved in ethanol and subsequently deposited onto the surface of fiber ferrule by using the adhesion effect with the evaporation technique.By integrating the ZnO nanoparticle-based SA into a laser cavity of an EDFL,a self-started and stable Q-switching is achieved at a low threshold power of 20.24 mW.As the pump power is increased,the pulse repetition rate is tunable from 10.34 kHz to 25.59 kHz while pulse duration decreases from 21.39μs to 3.65μs.Additionally,this Q-switched laser has a maximum energy per pulse of 19.34 nJ and an average output power of 0.46 mW.These results indicate the feasibility and functionality of the ZnO nanoparticles-based SA for Q-switched generation,which offers the flexibility and easy integration of the SA into a ring laser cavity.

High conversion efficiency, high power density Q-switched fiber laser

An acoustic-optic Q-switched all-fiber laser With a high-repetition-rate, a short pulse width, a wide spectrum, and a high conversion efficiency is experimentally demonstrated. In the laser configuration, a （1＋1）x 1 side-pumping coupler is introduced to perform backward pumping, and a 10/130%tm Yb fiber is adopted. The acoustic-optic component operates in the first direction, achieving a Q-switched pulse with a repetition rate adjustable in the range of 20 kHz-80 kHz. Under a repetition rate of 20 kHz and a pump power of 6.76 W, the fiber laser obtains a highly efficient and stable pulse output, with an average power of 4.3 W, a pulse width of 56 ns, a peak power of 3.83 kW, and a power density of 1.39x 101~ W/cm2. Particularly, the optic-optic conversion efficiency of the laser reaches as high as 64%. Another feature of the pulsed laser is that the high reflection mirror reflects the pump light as well, which brings the secondary absorption of the pump power into the gain fiber.

Tandem-pumped 1120-nm actively Q-switched fiber laser

We report on a tandem-pumped actively Q-switched fiber laser system emitting at 1120 nm.Parasitic oscillation is challenging in Yb-doped Q-switched 1120-nm fiber laser,which is suppressed by pumping with a fiber laser at 1018 nm.At least four times improvement in output peak power is demonstrated in a single laser setup with 1018-nm fiber laser pumping instead of 976-nm laser diode pumping.This is,to the best of our knowledge,the first demonstration of a tandem-pumped Q-switched fiber laser.